MEGATRONIX MEGALARM MEGA 2000 User manual

MEGA 2000 OPERATE
1
MEGA 2000
2-WAY LCD REMOTE ENGINE STARTER
AND KEYLESS ENTRY SYSTEM
Operation Manual
MEGATRONIX
CALIFORNIA, U.S.A.

MEGA 2000 OPERATE
2

MEGA 2000 OPERATE
3
WARNINGS:
As with any product that performs automatic functions, there are certain safety precautions that you
must practice and be aware of before using device.
1. Keep the transmitter out of reach of children.
2. Do not leave anyone in the vehicle while running on remote start.
3. Alert servicing personnel that the vehicle is equipped with a remote start system.
4. Do not start the vehicle by remote while it is in an enclosed area or garage.
5. Always apply the parking brake and lock the vehicle as you exit the vehicle.
6. Vehicle windows should be rolled up before vehicle is remote started.
7. If the unit malfunctions, disconnect the remote start fuse until the problem is resolved.
8. Use and operation of this system is the sole responsibility of the vehicle owner or operator.
9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets.
OPERATION:
A. REMOTE TRANSMITTER OPERATION:
Transmitter
Button
System Function
Remark
Lock Doors & Arm System
-
Arm and Delete The 2 Stage Shock
Sensor
Press twice within 3 seconds
-
Arm System and Hidden Alarm Function
Press within 3 seconds
Car Locator
Upon armed
(3-second)
Panic function
Press and Hold for 3 seconds
+
Silent Arming / Disarming
Ignition in "off" position
+
(2-second)
Active Anti Car-Jacking Mode
Ignition in "on" position press
and
hold for 2 seconds
Unlock Doors & Disarm System
-
Two Steps Door Unlock & Disarm System
Press twice within 3 seconds
(2-second)
Trunk Release (Channel 3)
Press and Hold for 2 seconds
-
Passive Arming By-pass
While the system Disarmed
-
Activate or Turn Off The Remote Start
Press twice within 3 seconds
+
Turbo Time Mode
+
Channel # 4 Timer Output
B. LED INDICATORS:
LED
Function
LED
Function
Off
Disarmed
2 flashes... pause
Zone 2 / Trigger on Trunk/Hood
Slow Flash
Armed
3 flashes... pause
Zone 3 / Trigger on Door Switch
Fast Flash
Passive Arming
4 flashes... pause
Zone 4 / Trigger on Shock Sensor
On (Solid)
Valet Mode
5 flashes... pause
Zone 5 / Trigger on Ignition Switch
C. CHIRP INDICATORS: D. PARKING LIGHT:
Chirp
Function
Parking light
Function
1 chirp
Arm
1 flash
Arm
2 chirps
Disarm
2 flashes
Disarm
3 chirps
Ajar Warning
3 flashes
Disarm / Triggered
4 chirps
Disarm /
Triggered
12 flashes
Car Locator
6 chirps
Car Locator
Constant On
Under Remote Start
E. ALARM OPERATING CONDITION:
Siren / Horn
Parking Light
LED
Doors
Starter
Dome Light
1. Arming
1 or 3 Chirps
1 Flash
Slow Flash
Locking
Disable
2. Disarming
2 or 4 Chirps
2 or 3 Flashes
Unlocking
Turns on 30 sec

MEGA 2000 OPERATE
4
3. Trigger
Alarming
Flashes
Slow Flash
Disable
Flashes
4. Panic
Alarming
Flashes
Flashes
5. Car-Jacking
Alarming
Flashes
Disable
Flashes
6. Car Locator
6 Chirps
12 Flashes
Locking
F. ACTIVE ARMING –LOCK & ARM:
1.Press button on the transmitter.
2. The siren will chirp once and parking light will flash once indicating that the system is now armed.
The vehicle door will lock and dome light turns on for 10 seconds upon arming when interfaced
with the security system.
AJAR WARNING: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.
(See Alarm Feature “I - 4 Programming)
SILENT ARMING / DISARMING: Press the transmitter and buttons at the same time will
arm or disarm your security system, No chirp sound will be heard, arm / disarm confirmation will be
through the vehicles parking lights only.
SHOCK SENSOR BY-PASS: Press the button on the transmitter two times within 3 seconds
will arm the security system and by-pass the shock sensor. The system will chirp one additional
time to confirm the sensor bypass mode was activated. The sensor bypass feature is programmed
to activate for one arming cycle only. The security system will return to normal operation during the
next arming cycle.
HIDDEN ALARM FUNCTION: Press the button first; within 3 seconds press the button to
activate the hidden alarm function. The security system will arm and with “Hidden Alarm Function”.
The siren / horn will be silenced even if the sensor is triggered in the armed status.
G. PASSIVE ARMING
Active arming / disarming is controlling your security system via the remote transmitter. This
security system is equipped with an optional Passive Arming feature, which allows the security
system to arm 30 seconds after the last door is closed. Operation is as follows.
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you
reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing
again once the vehicle all entrances are closed.
3. After 30-second time has elapsed, the security system will automatically “ARM”. The siren will
chirp [1] time and the parking lights will flash [1] time.
PASSIVE ARMING WITH PASSIVE DOOR LOCKING (See Alarm Feature “I - 2”
Programming):
The vehicle doors will automatically lock after passive arming cycle has been completed.
PASSIVE ARMING BY-PASS: While the system disarmed, Press the button twice, the
security will respond with [1] chirp and LED will turn “ON”. The security system will remain in this
temporally state for as long as you wish. To exit passive by-pass, press the transmitter or
button and the system will return to normal status.
H. ACTIVE DISARMING –UNLOCK & DISARM:
1. Press button on the transmitter.
2. The siren will chirp once and parking light flash once to indicating that the security system is
now disarmed. The vehicle’s door will unlock and dome light turns on for 30 seconds upon
disarming when interfaced with the security system.
TAMPER DISARMING: If alarm triggered, upon disarm the system, siren chirp 4 times, parking
light flash 3 times.
PATHWAY ILLUMINATION (See Alarm Feature “II - 4” Programming): This feature turns the
parking light “ON” for 30 seconds upon a unlock signal and for 10 seconds upon the lock signal.
TWO STEPS DOOR UNLOCK (See Alarm Feature “II - 1” Programming): This feature will
independently unlock the driver’s door only when disarming the security system. Pushing the
button a second time within 3 seconds will unlock the other doors.
AUTOMATIC RE-ARM (See Alarm Feature “I - 3” Programming): If this feature is selected, the
security system will automatically re-arm itself in 60 seconds after disarming with remote transmitter.
Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed.
I. DISARMING WITHOUT A TRANSMITTER (Alarm Feature II -6 Programming)

MEGA 2000 OPERATE
5
OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default Setting)
The Override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Within 10 seconds push and release the valet switch. The alarm will stop sounding and enter
the disarm mode. You can now start and operate the vehicle normally.
OVERRIDE THE ALARM WITH PASSWORD PIN CODE: (Alarm Feature II - 6 Programming)
Unlike valet switch easily found, and defeated, this security system allows the consumer to program
a password pin code, offering a higher level of security.
1. Enter the vehicle and turn the ignition switch to 'ON’ position (Alarm will sound).
2. Within 5 seconds, enter your chosen the first digit code by press and release the Valet Switch.
(When finished above procedures, system's siren stop alarming, parking light stop flashing, but
the vehicle cannot be start and drive away).
3. Within 15 seconds of last digit code enter (the 1st code), turn Ignition Switch “OFF” then “ON”.
4. Within 15 seconds, enter your chosen of second digit code by pressing and release Valet Switch.
5. Turn the ignition switch “OFF” position. [4] Chirps form siren/horn, [3] flash from parking light to
indicate the system was disarmed.
Note: You must override the alarm within 60 seconds. If not, the system will automatically re-arm.
EXAMPLE: To Override the System with the Password Code 83, you would;
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound).
2. Within 5 seconds, Press and Release the Valet Switch 8 times
(When finished above procedures, system's siren stops alarming, parking light stop flashing,
other sensor stop trigger, but the vehicle cannot be start and drive away.)
3. Within 15 seconds of last digit code enter (1st code), turn Ignition Switch “OFF” and then “ON”.
4. Within 15 seconds, Press and Release the Valet Switch 3 times
5. Turn the Ignition Switch to “Off” position. [4] Chirps form siren/horn, [3] flash from parking light to
indicate the system was disarmed.
J. VALET MODE: (System in Disarm or Valet mode)
The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand
your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all
alarm function and remote start functions are bypassed, however the remote panic feature and
remote door locks will remain operational. To use the valet mode, the system must first be
disarmed either by using you remote transmitter, or by operating the Manual override sequence.
Enter Valet Mode:
1. From the disarmed condition, turn the ignition to “ON” position.
2. Push and hold valet switch for 2 seconds until the LED turns on. The LED wills remain on as
long as the system is in 'valet mode'.
Exit Valet Mode:
1. Return to normal operation, turn ignition 'on'.
2. Push and hold valet switch for 2 seconds, The LED wills turns off indicate the system are exiting
the valet mode.
K. CAR LOCATOR
Under armed mode, press the button to active car locator function. The siren will chirp 6 times.
The parking light will flash 12 times, for you to easily locate your car.
L. PANIC FUNCTION:
Transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency.
1. Press and hold the button for 3 second. The alarm will immediately sound.
2. During panic mode, the normal function of this transmitter button will be suspended. The
transmitter and buttons can be used to lock and unlock the door (if the option is installed),
however once the button is pressed, the vehicle’s starter disable device, (where installed) will
be enable allowing the vehicle to start.
3. To stop the alarm, press and hold the transmitter or button on the transmitter again for 3
seconds. Also if any transmitter buttons other than or button is pressed and released, the
panic mode will be turned off immediately.
4. If the button is not pressed, the alarm will automatically stop after 30 seconds.
M. TRIGGER THE SYSTEM
When armed, your vehicle is protected as follows:
1. Light impact will trigger the warn-away signal.

MEGA 2000 OPERATE
6
2. Heavy impacts / doors open / hood open / trunk open / turn on the ignition key will trigger the
programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren, horn,
parking lights, and dome light will turn on to alerting of an intrusion for 30 seconds. Then it will stop
and automatic reset and re-arm. If the one of sensors or detectors still active, the alarm system will
sound a maximum of 6 times of 30 seconds cycles.
N. ANTI CAR- JACKING
Warning: If you don't need the carjacking function in this alarm system, be sure to set carjacking
feature “OFF”. This system is default setting all car-jacking “OFF”. (See Alarm Feature I -5
Programming.)
ACTIVE ANTI CAR JACKING:
1. Press and hold the transmitter and buttons at the same time for 2 seconds while the
vehicle’s ignition is ON. The parking lights will turns on for 1.5 seconds to indicate the system
enters the car-jacking mode.
2. Once the system in car-jacking mode, if you are forced from the vehicle, the system will be
trigger when the door is opened and closed while the ignition is “ON”.
PASSIVE ANTI CAR- JACKING:
1. Turn the ignition switch to “ON” position; the system enters the car-jacking mode.
2. Once the system in car-jacking mode, If you are forced from the vehicle, the system will trigger
when the door is opened and closed while the ignition is “ON”.
TRIGGER THE ANTI CAR -JACKING MODE:
A). 50 seconds after system has been triggered, siren will start chirping for 15 seconds.
B). During this 15 seconds period of chirping, you will be alerting to push the valet switch once to
turn off the car-jacking feature. If not, it will enter second timer carjacking.
C). 65 seconds after system has been triggered, siren starts alarming and parking lights flashing.
D). 90 seconds after the system has been triggered.
1. The siren still alarming and the parking light flashing, AND
2. The starter disable will activate to prevent the vehicle from starting.
3. It will remain active until the vehicle's battery power exhausted.
OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR- JACKING:
Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will
stop and the system disarmed
Note: If you use password pin code to double protect the vehicle security, you will need to use it to
completely disarm the system.
O. DOME LIGHT CONVENIENCE DELAY & SUPERVISION
The alarm with a unique feature which will turn on your vehicle dome light as following:
1. Upon disarming, the interior light will remain on for 30 seconds.
2. If the vehicle is intruded, the interior light will flash for the same duration as the siren.
Note: Turn on the ignition switch or arm the alarm will turn off the dome light.
P. IGNITION CONTROL DOOR LOCK/UNLOCK. (See Alarm Feature II –2
Programming).
If vehicles door locks have been wired to security system, system will automatically lock vehicle's
doors when ignition is turned “ON” and /or unlock vehicle’s doors when ignition is turned “OFF”
Q. TRUNK RELEASE (CHANNEL 3) OUTPUT.
Press and hold button on the transmitter for two seconds to remote control the
trunk release or other electric devices.
R. CHANNEL 4 TIMER CONTROL OUTPUT (See Alarm Feature III –4 Programming.)
Press the transmitter and buttons at the same time to active Channel 4 function. Channel 4
is user-programmable timer output. You may program the built-in timer to send a ground signal for
any time duration from 1 second to 120 seconds. For instance, this timer output may be used to
turn on the headlight, power window or sunroof. (Factory defaults setting at momentary output.)
S. DRIVER PAGING / LOSE & FOUND (For two-way transceiver operation only)
It is useful the event that someone wants to page the driver of the parked vehicle or someone
cannot find his LCD remote control transceiver.
Under the ignition switch “off” condition, press and hold the valet switch for 2 seconds to page the
driver, one chirp sound shall be emitted from the vehicle and the paging melody sound continues
sounding from you Remote LCD transceiver and CALL indication flashes on the LCD screen.
T. OUT OF RANGE INDICATION: (See Alarm Feature II –5 Programming.)

MEGA 2000 OPERATE
7
If this feature is selected, system will automatically check range every 30 minutes after armed.
1. If user is within range, RANGE icon will display on LCD screen.
2. If user is out of range, five short “bi” sounds emit and RANGE icon will disappear on LCD screen.
Note: Programming “out of range indication”will decrease the life expectancy of battery
U. POWER ON MEMONRY:
This security system is equipped with circuitry that will allow the unit to remember its alarm state if
the power is lost and then reconnected.
V. ALARM UPGRADE
This unit is capable of being upgraded to an alarm system so as to detect if a thief is trying to open
a door, the hood, or the trunk and has an input for a shock sensor to detect impact to the vehicle by
a thief. If you would like to upgrade this unit to an alarm system, please contact your authorized
reseller. REMOTE START OPERATION:
A. TO REMOTE START THE VEHICLE:
1. Press button twice on the transmitter.
2. The parking light will activate to indicate the remote start received the signal. (A melody sounding
from your Remote LCD transceiver and IGN icon will flashes on the LCD screen to confirm the
remote start was activated.)
3. The engine will start approximately 5 seconds.
4. Once the engine is running, after couple seconds the parking light will turn on again and climate
controls will activate and adjust the vehicles interior temperature to your preset setting (While the
vehicle is running, the RUNNING icon on the LCD screen will flash and it will indicate countdown
timer based on the 5, 10, 20 or 30 minute run time set up by your installation center).
5. The vehicle will run for 5 to 30 minute cycle and automatically shut down. (When the unit shuts
off the countdown timer will turn off and the transmitter will play a melody.)
Note: The Remote Start Unit will not start the vehicle if any one of the following
conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. Move the optional remote start enable toggle switch to OFF position. (If installed)
4. The gear selector is in any gear other then “PARK” or “NEUTRAL”
SAFE START (Child Safety Mode) (See Start Feature I –5 Programming)
Factory defaults setting to press the button twice on the transmitter to start the vehicle.
Programming this feature to eliminate accidental remote start, when kids enter this transmitter, user
presses the transmitter and buttons at the same time to start the vehicle.
B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START:
To operate the vehicle while the remote start is running vehicle engine.
Insert the ignition key and turn it to “ON” (not the start) position.
Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.
C. TEMPORARY STOP FEATURE:
This feature allows the vehicle to remain running after the key has been removed from the ignition.
This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of
time, but would like to leave the motor running and the climate control on.
1. Before turning off the engine, press the button twice on the transmitter and the LED indicator
will flash 3 times to confirm enter.
2. Turn the ignition key to OFF position. (The engine will stay running.)
3. The engine will run until the pre-programmed time elapsed or shutdown input is received.
E. TURBO TIMER MODE: (See Start Feature “I - 6” Programming)
Turbo timer mode keeps the engine running after arriving at you destination for a programmable
period of 1/ 3 or 5 minutes, This allows the system’s time to conveniently cool down the turbo after
you have left the vehicle. To activate:
1. While engine is running, place the transmission gear in park position and pull up the hand brake.
2. Before turning off the engine, press and release and buttons at the same time.
-- The parking light wills turn on to indicate the remote start has entered turbo charger mode. --
3. Pull off the “Ignition Key” from the key cylinder.
-- Engine keeps running. --

MEGA 2000 OPERATE
8
4. Exit and secure the vehicle.
-- Engine continues running until the pre-programmed time elapsed. --
F. TIMER START: (See Start Feature “I - 7” Programming)
This unit can be programmed to start and run the engine every 3 (2) hours. The engine will run for
the programmed running time and then shut down.
IMPORTANT: Timer Start should be used only in open areas, never start and run the vehicle in on
enclosed space as a garage or carport.
This feature is design for an extreme cold climate usage. The system will auto start the vehicle
every 3 (2) hours, to prevent engine freezing and hard to start.
A MAXIMUM OF SIX CYCLES CAN OCCUR.
ENTER:
1. Press the button twice to remote start the vehicle. As soon as the vehicle is running and the
parking light have turned on or flashing.
2. Immediately depress the button once, within 2 seconds
3. Rapidly depresses the button. The parking light will flash (3) times. The siren or horn chirps
(3) times. The vehicle is now programmed to start every 3 (2) hours.
4. Press the brake pedal to stop the vehicle running.
Exit the timer start:
Timer start can be exited manually as follows:
Make sure the remote start system is not operating the engine.
2. Turn the ignition on. The LED and parking light will flash (4) times. The horn chirps (4) times. OR
1. Press the button twice to remote start the vehicle. As soon as the vehicle is running and the
parking light have turned on or flashing.
2. Immediately depress the button then press and hold the button for 2 seconds. The
parking light will flash (4) times. The siren or horn chirps (4) times. The vehicle is no longer
programmed to start automatically.
G. TO TURN OFF THE REMOTE START:
When the engine is running (by remote start), if you want to stop it:
Press button twice on the remote transmitter under remote start mode.
Move the optional remote start enable toggle switch to OFF position (If installed).
Press the brake pedal. Vehicle will shut down and turn off parking light to indicate engine stopped.
H. SHUT-DOWN INPUT FOR REMOTE STARTER:
If any of the following conditions exist while the system is operating, the engine will not start or will
shut down immediately:
1. The hood is opened.
2. The brake pedal is pressed.
3. Engine is over-revved {“Tachometer checking type” only}.
4. The pre-programmed run time (5/10/20/30 minutes) has elapsed.
5. Press button twice on the remote transmitter under remote start mode.
6. Move the optional remote start enable toggle switch to OFF position (If installed).
7. The vehicle refused to start running after {3} unsuccessful attempts.
I. DISABLING THE REMOTE START SYSTEM: (If installed)
This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle
from being remote started accidentally. This feature is useful if the vehicle is being serviced or
stored in an enclosed area. To disable the remote start, move the optional remote start enable
toggle switch to the OFF position.
LCD REMOTE CONTROL TRANSCEIVER:

MEGA 2000 OPERATE
9
NOTE: If the system is interfered by stronger radio frequency around, sources of high voltage
electric power or such Obstacles like tall buildings and so on, the transmission range may
get shorter as the system uses low output powered frequency.
A. BATTERY REPLACEMENT:
A 1.5V type AAA Alkaline battery powers the Remote Transmitter. When the power of the battery
weakens, a icon shall be displayed on the LCD screen. When the old battery is replaced to
new one, there will be beep sounds indicate the power is up.
B. REMOTE LCD ICONS WITH FUNCTION:
Door Lock
Your vehicle doors are locked
Door Unlock
Your vehicle doors are unlocked
and the system is Disarmed
Armed Mode
Your vehicle is in armed mode
Valet Mode
All the function shall be
temporarily on hold.
Remote Transmission
You are transmitting the signal to
control unit
In –Range Indicator
Your are within the remote
control range.
Trunk/Hood Trigger
Trunk or Hood is illegally opened
(Zone 2)
Door Open Warning
Doors are illegally opened (Zone
3)
Shock Sensor Trigger
Trigger on Shock Sensor (Zone 4)
Ignition Trigger
Trigger on Ignition Switch (Zone
5)
Warn Away trigger
Trigger on Shock Sensor (Zone 1)
Low Battery
You have to replace the battery
of remote control.
Vibration Mode
Remote Control vibrates when the
system is triggered
Driver paging / Lose and
Found
Someone is paging you in front
of your vehicle
Power Save Mode
Save the battery power
Engine Running
Your vehicle's engine is running
C. PROGRAMMING OF THE LCD REMOTE TRANSMITTER:
NOTE: Press and hold all four remote control buttons simultaneously until one long beep is
heard. LCD PROGRAMMING MODE has now been entered.
Transceiver Button
System Function
Remark
PROGRAM MODE -
Switching code for 2nd / 1st Car
Operation
Press within 5 seconds
PROGRAM MODE -
Melody / Vibration Mode
Press within 5 seconds
PROGRAM MODE -
Power Save Mode
Press within 5 seconds
LCD screen lamp turns on for 5 seconds.
-+
System’s Status Check
Press within 3 seconds
-+
Clear the Flash Icon and Melody Sound
Press within 3 seconds

MEGA 2000 OPERATE
10
1. Second Vehicle Security Operation: Remote transmitter can be utilized to control a second
vehicle security system. To program the remote control transmitter to a second vehicle, follow the
instructions for Transmitter programming. All programming parameters same except for following:
For Regular Remote Control Transmitter:
1. Prior to pushing any button on the transmitter, press Select II button first on the transmitter.
2. Once II button is pressed the LED on the transmitter will illuminate for 3.5 seconds to indicate
the second transmitter pin code has built-in.
3. While the LED is illuminated, press any button on the remote control transmitter to control a
second vehicle security system.
For 2-way LCD Remote Control Transceiver:
2nd Car Operation: While the “II”icon display on the LCD screen, you can remote control and
communicate with a second vehicle security system. It has two short “bi” sounds while pressing the
button of the LCD screen transceiver.
1. Press and hold all four remote control buttons simultaneously until one
long beep is heard. Programming has now been entered.
2. Within 5 seconds press & hold button until two beep sounds are heard &
the “II”icon will display on LCD screen indicating 2nd transceiver pin code
has built-in.
3. To exit programming mode, take no action for five seconds. Remote control
will generate two long beeps to indicate programming mode has been exited.
Back to 1st Car Operation: You can remote control and communicate with a first vehicle security
system. It has one short “bi” sound while pressing the button of the LCD screen transceiver.
1. Press and hold all four remote control buttons simultaneously until one
long beep is heard. Programming has now been entered.
2. Within 5 seconds press and hold button until one beeping sound is heard.
3. To exit programming mode, take no action for five seconds. Remote control
will generate two long beeps to indicate programming mode has been exited.
2. Vibration / Melody Mode: Useful when you are in a noisy place and difficult to hear beep sound
from remote control as remote control in this mode vibrates it if your security system is triggered.
1. Press and hold all four remote control buttons simultaneously until one
long beep is heard. Programming has now been entered.
2. Within 5 seconds, press the button to select the mode of vibration or
melody, the icon will displayed on the LCD screen to show the LCD
remote transceiver is on vibration mode.
3. To exit programming mode, take no action for five seconds. Remote control
will generate two long beeps to indicate programming mode has been exited.
3. Power-Save Mode: While the power save mode, the LCD remote transceiver “sleep”until a
button is pushed, extending the life of battery. When power save mode is “Off”, the remote control
will wake up periodically to check for messages from the security module.
1. Press and hold all four remote control buttons simultaneously until one
long beep is heard. Programming has now been entered.
2. Within 5 seconds, press the button to toggle “On”or “Off”. The remote will
beep once for “On”, twice for “Off”. When power save mode is “On”, the
icon on the LCD screens to indicate entry the “power save mode”
3. To exit programming mode, take no action for five seconds. Remote control
will generate two long beeps to indicate programming mode has been exited.
4. Screen Lamp ON: Press the button once, the LCD screen lamp will turns on for 5 seconds
5. System’s Status Check When you want to check the system’s present status through the LCD
screen, Press the transceiver button first, within 3 seconds press and buttons at the same
time. It responds with one melody sound, the LCD screen should be illuminated.
Note: If it has no responds then you are out of range.
6. Clear the Flash Icon and Melody Sound: Press button first, within 3 seconds press
and buttons at same time. It will clear flash icon and melody sound on LCD screen transceiver
7. Stop The Trigger Melody Sound: While triggering the alarm the LCD screen will alert user
through melody sound and flashing trigger icon, press any button on the LCD remote transmitter to
stop melody sound only, the remote control buttons will not send a command to the system.

MEGA 2000 OPERATE
11
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions.
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.

MEGA 2000 OPERATE
12