MEGATRONIX MEGALARM MEGA 462 User manual

MEGA 462
1
MEGA 462
DELUXE 3-CHANNEL
CAR ALARM SECURITY SYSTEM
Installation And Operation Manual
MEGATRONIX
CALIFORNIA, U.S.A.

MEGA 462
2

MEGA 462
3
WIRING DIAGRAM
H1: Main 5 Pin White harness
H3: 6 Pin White Mini Connector
Black Antenna Wire
LED Indicator
Valet Switch
H7/3 Blue Wire: (-) 200mA Unlock
H7/1 Green Wire: (-) 200mA Lock Pulse
Pulse
H7 3 Pin
White
H2 4 Pin
Orange
H5 2 Pin
Blue
H6 2 Pin
White
H4 Black
Wire
Dual Zone
Shock
Sensor
H1 5 Pin
White
H3 6 Pin
White
H1: MAIN 5 PIN WIRE HARNESS:
5. Red Wire: +12V To Constant Battery Source
4. Brown Wire: Positive output To
3. Black Wire: Ground to Vehicle FRAME
2. White Wire: Parking Light Relay Output
15A Fuse
1. Red / White Wire: Parking Light Relay input
Siren Or Horn (Programmable)
H3: 6 PIN MINI CONNECTOR WIRE HARNESS:
6. Gray Wire: (-) 200ma Programmable Output
2. Blue Wire: Zone 2 / Instant Trigger Ground Input
1. Violet Wire: Zone 3 / Positive Door Pin Switch Input
4. Yellow Wire: Zone 5 / To Ignition Switched + 12V
5. Orange Wire: 200mA Grounded when armed
3. Green Wire: Zone 3 / Negative Door Pin Switch Input
85
86
30
87a
87
Cut
To start solenoid
From ignition switch
Red
wire
White wire
Orange
wire
Channel 2 / 2 Step Door Unlock / Pager Output.
12V
12V

MEGA 462
4
WIRING
Keep wiring away from moving engine parts, exhaust pipes and high-tension cable. Tape wires that pass
through holes on the firewall to prevent fraying. Watches out sharp edges that may damage wires and
causes short circuit.
CAUTION: Do not connect the wire harness to the control module until all wiring to vehicle is complete.
H1: MAIN 5 PIN WIRE HARNESS:
H1/1. RED / WHITE WIRE –PARKING LIGHT RELAY INPUT --
The RED/WHITE wire is the input to the flashing parking light relay. The connection of the RED/WHITE
wire will determine the output polarity of the flashing parking light relay.
If the vehicle you are working on has +12volt switched parking lights, you don’t need connect this wire.
This wire already connected to +12volt.
If the vehicle’s parking lights are ground switched, cut the RED/WHITE wire, connect the RED/WHITE to
chassis ground.
H1/2. WHITE WIRE -- PARKING LIGHT RELAY OUTPUT (+12 V 10A OUTPUT) --
Connect the WHITE wire to the parking light wire coming from the headlight switch. Do not connect the
white wire to the dashboard lighting dimmer switch. (Damage to the dimmer will result). The limitation of
the white wire is 10 AMP max. Do not exceed this limit or damage to the alarm and parking relay will
result.
H1/3. BLACK WIRE -- SYSTEM GROUND –
This is main ground connection of the alarm module. Make this connection to a solid section of the
vehicle frame. Do not connect this wire to any existing ground wires supplied by the factory wire loom,
make the connection to the vehicle's frame directly.
H1/4. BROWN WIRE -- SIREN DRIVE OR HORN OUTPUT -- (Set Feature III –1 Programming)
SIREN DRIVE OUTPUT (Factory default setting)
This is the positive (+) output connection for the siren. Current capacity is 2 amps. Make connection to
the (+) red wire from the siren. Make the (-) black wire coming from the siren to a good chassis ground.
(+) LOW CURRENT HORN OUTPUT -- (Set Alarm Feature III –1 To Horn Output)
This wire is provided to use the existing vehicle's horn as the alarm system's optional's warning audible
device. It's a transistorized low current output, and should only be connected to the low current positive
(+) output from the vehicle's horn switch.
H1/5. RED WIRE -- SYSTEM POWER (+12V CONSTANT) --
The RED wire supplies power to the system. Connect this wire to a constant +12 volt source.
H2: 4 PIN ORANGE CONNECTOR FOR 2 STAGE SHOCK SENSOR
4. Green Wire / Warn Away Input
3. Blue Wire / Zone 4 Ground Trigger
2. Black Wire / Negative
1. Red Wire / +12Volts
Function: Allows easy positive, negative, instant trigger, and warn-away trigger connection with quick
disconnect ability for other detection devices.
H3: 6-PIN MINI CONNECTOR WIRE HARNESS.
H3/1. VIOLET WIRE -- POSITIVE DOOR SWITCH SENSING INPUT--
This wire is the positive trigger input wire for positive door pin switch. This wire is connection for "positive"
type factory door pins(typical FORD MOTOR). Locate the "common wire" for all door pins and make the
connection of the Violet Wire here.
H3/2. BLUE WIRE -- GROUND INSTANT TRIGGER INPUT --
This wire is the ground trigger input wire for hood/trunk pin switches.
H3/3. GREEN WIRE -- NEGATIVE DOOR SWITCH SENSING INPUT --
This wire is the ground trigger input wire for negative door pin switch. This wire is connection for "grounding"
type factory door pins locate the "common wire" that connects the door pin switches. Make the connection of
the Green Wire here.
H3/4. YELLOW WIRE –TO IGNITION SWITCHED +12V --
This wire is connected to a switched 12 volts source. This wire should receive "12 Volts" when the ignition
key is in the "ON" and "START" position. When the ignition is turned "OFF", this wire should receive "0"
voltage.
H3/5. ORANGE WIRE –(-) 200mA GROUNDED OUTPUT WHEN ARMED --
This wire will become grounded when the alarm is armed. The current capacity of this wire is 200mA. This
output can control starter disable, when an intrusion is detected and the system is triggered. The vehicles
prevent from any unauthorized starting.
a). Find the wire from the starter solenoid, (usually located on the starter) and going to the ignition switch.

MEGA 462
5
b). When found, use voltmeter, connect one probe of the voltmeter to ground and connect the other end of
the probe to the starter wire, it should receive "12 Volts" only when the ignition key in the "START"
position.
c). After locating the correct wire, cut it in half, try to start the vehicle. The engine should not "crank over".
d). When the extend wires are needed, they must be exactly same gauge as the cut wire. Connect the cut
wire from the key switch to the RED wire (pin #30) of the relay, and connect the starter wire to the
WHITE wire (pin #87a ) of the relay.
e). Connect the H3/5 ORANGE Wire from the control module to the ORANGE wire (pin #86) of the relay.
NOTE: If more than one electronic device will be connected to the H3/5 ORANGE Wire, it will be
necessary to isolate the connection of each device control wires with a 1N4003 diode.
87
87a
85
30
86
IN4003 Diode
H3/5 Orange wire
“Start”
“On”
White wire
X
Cut
Red wire
Orange wire
“Acc”
“Off”
Starter
H3/6 . GRAY WIRE –(-) 200mA PROGRAMMABLE OUTPUT –
CHANNEL 2 OUTPUT (Factory default setting)
This will become a 1 second pulse ground by press and hold the button II on transmitter for two seconds,
the current capacity of this wire is 200 mA. this feature allows you to remote control trunk release or
other electric device.
2 STEPS UNLOCK OUTPUT (Set Feature III –2 Programming to “2 Step Door Unlock Output)
The 2 steps unlock feature will work for the most fully electronic door lock circuit. The vehicle must have
an electronic door lock switch (not the lock knob or key switch), which locks and unlocks all of vehicle's
doors. When wired for this feature, press the button II one time will disarm the alarm and unlock the
driver's door only. If, press button II two times within 3 seconds, the alarm will disarm and all doors will
unlock.
PAGER OUTPUT (Set Feature III –2 Programming to “PAGER Output)
This wire provides a negative output, when the alarm triggered. The current capacity of this wire is
200mA. For optional electrical device in this system, please connected to an additional relay. (I.E. Pager
interface....)
H4: RF ANTENNA - BLACK THIN WIRE
The black thin wire on control module is the receiver antenna wire. Antenna placement is very important!
Ensure that it is unwrapped and stretched out with the last 6" straight and keep it away from large metal
objects or chassis for best reception.
H7: 3 PIN DOOR LOCK CONNECTOR:
Blue Wire
Green Wire
(- ) 200mALock Pulse
(- ) 200mAUnlock Pulse
3 Pin Mini-Molex Connector
I
INSTALL NEW DOOR LOCK MOTOR
Blue Wire
Green
Wire
+12V
30
86
87a
85
87
30
86
87a
85
87
3 Pin
Plug To
Alarm
NEGATIVE TRIGGER DOOR LOCK SYSTEM
Blue Wire Door Unlock
Green Wire Door Lock
Locking
Master
Switch
To Exiting
Door Lock Relay
POSITIVE TRIGGER DOOR LOCK SYSTEM
Locking
Master
Switch
To Exiting
Door Lock Relay
+ 12V
Blue Wire
Green
Wire
+12V
30
86
87a
85
87
30
86
87a
85
87
3 Pin
Plug To
Alarm

MEGA 462
6
+12V
Master Door
Lock Switch
X
X
Splice
Splice
Cut the Existing
Lock Wire
To Door
Lock
Motor
To Slave Door
Lock switches
Cut the Existing
Unlock Wire
3 Pin Plug
To Alarm
5-WIRE ALTERNATING DOOR LOCK
30
86
87a
85
87
30
86
87a
85
87
+12V
Green Wire
Blue Wire
VACUUM OPERATED CENTROL LOCKING
Green Wire
Blue Wire
+12V
X
Cut
Compressor
Door Switch
30
86
87a
85
87
30
86
87a
85
87
3 Pin
Plug To
Alarm
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
5 WIRE ALTERNATING DOOR LOCKS
+12V
Cut the Existing
Lock Wire
Cut Existing Unlock
Wire
X
Cut the Unlock Wire
Lock
Unlock
OEM Door Master Lock
Switch
OEM Slave
Door Lock
Switch
+12V
Lock
Unlock
To All Other
Door Lock
Motors
6-Pin
Plug
From
Alarm
H3/6 Gray
Wire
x
X
H7/1
Blue Wire
OEM Driver’s
Door Lock Motor
+ 12V
+ 12V
85
86
87
87A
30
30
87
85
87A
86
30
87
85
87A
86
H7/3 Green Wire
3 Pin
Plug
To
Alarm
VACUUM OPERATED DOOR LOCKING SYSTEM:
TYPICAL OF MERCEDES BENZ AND AUDI.
Locate the wire under the driver's kick panel. Use the
voltmeter connecting to ground, verify that you have the
correct wire with the doors unlocked, the voltmeter will
receive "12 volts". Lock the doors and the voltmeter will
read "0 volt". Move the alligator clip to +12V and the
voltmeter will receive "12 volts". Cut this wire and make
connections. Be sure to program door lock timer to
3 seconds.(See Feuture II –1 Programming.)
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
GROUND SWITCHED DOOR LOCKS
Cut Existing Unlock
Wire
X
Lock
Unlock
OEM Door Master Lock Switch
To All Other
Door Lock
Motors
6-Pin
Plug
From
Alarm
H3/6 Gray Wire
OEM
Driver's
Door Lock
Motor
Existing Neg.
Lock Wire
Existing Neg.
Unlock Wire
86
30
85
87
87A
+ 12V
H7/3 Green
Wire
Door Lock
H7/1 Blue
Wire
Door Unlock
3 Pin Plug
To Alarm
OEM Door
Lock Relay
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
POSITIVE SWITCHED DOOR LOCKS
Cut Existing Unlock
Wire
X
Lock
Unlock
OEM Door Master Lock Switch
To All Other
Door Lock
Motors
6-Pin
Plug
From
Alarm
H3/6
Gray Wire
OEM Driver's
Door Lock
Motor
+ 12V
Existing Pos.
Lock Wire
Existing Pos.
Unlock Wire
30
87A
87
86
85
+12V
+ 12V
OEM Door
Lock Relay
86
30
85
87
87A
H7/1 Blue
Wire
Door Unlock
H7/3 Green Wire
Door Lock
+ 12V
86
30
85
87
87A

MEGA 462
7
PROGRAMMING
A. PROGRAMMING TRANSMITTER:
Enter:
1. Turn the Ignition switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 3 times and hold it until a long chirp is hearing then release the valet switch. You
are
now in the Transmitter programming mode.
Program:
1. Press button on one of the transmitter until the siren respond with a confirming chirp the first transmitter is
now programmed.
2. Press button on the second transmitter until the siren respond with a confirming chirp, the second
transmitter is now programmed.
3. Apply the same procedure to program 3rd and 4th.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. A 3 long chirps to confirm exit.
Note: If more than 4 transmitters programmed, the system only kept the last 4 transmitters.
B. ALARM FEATURES PROGRAMMING:
ALARM FEATURE “I” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 2times and hold it until one chirp and a long chirp is hearing then release the
valet switch. You are now in the Alarm feature ‘I’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
a. The siren chirps and LED pause will indicate the latest setting.
b. The factory default setting is always [1] LED flash, [1] chirp.
4 Depress the transmitter button ‘A’ to change the feature. Simple re-depressing the transmitter button ‘A’
again until the module advances to your desired setting.
a. In this case, Press button ‘A’ again, the module would advance to [2] LED flash, [2] chirp. Press button
‘A’ again, the module would advance to [3] LED flash, [3] chirps etc.
b. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
1. Button I
Chirps on
Chirps off
2. Button II
Automatic Rearm On
Automatic Rearm Off
3. Button I + II
With Door Ajar error chirp.
Bypass Door Ajar error chirp
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps to confirm exit.
ALARM FEATURE “II” PRORAMMING:
1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch 4times and hold it until two chirps and a long chirp is hearing then release the
valet switch. You are now in the Alarm feature ‘II’ programming mode.
3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
1 Button I
0.9-second Door lock
pulses.
3.0-second Door lock
pulse.
Double pulse unlock
2 Button II
Active arming
Passive arming without
passive door locking
Passive arming with
passive door locking.
3 Button I + II
Ignition controlled door
locks & unlocks
Without ignition controlled
door locks & unlocks
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps to confirm exit.
ALARM FEATURE “III” PRORAMMING:
1 Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch 6 times and hold it until three chirps and a long chirp is hearing then release the
valet switch. You are now in the Alarm feature ‘III’ programming mode.
3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse

MEGA 462
8
1 Button I
H1/4 Brown Wire = Siren
Output
H1/4 Brown Wire = Horn
Output
2 Button II
H3/6 Gray Wire = Trunk
(Channel 2) Output
H3/6 Gray Wire = Two
Step Door Unlock Output
H3/6 Gray Wire = Pager
Output
3 Button I + II
Car Jacking Off
Car Jacking On
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps to confirm exit.
OPERATION MANUAL
A. TRANSMITTER OPERATION:
Transmitter Button
System Function
Remark
Button I
Arm / Lock door
Button I –I
Arm and Delete Optional Sensor
Press twice.
Button I
Car Locator
System in Armed
Button I for 3 seconds
Panic function
Press 3 seconds
Button II
Disarm & Unlock Door
Button II –II
Two Steps Door Unlock & Disarm
System
Press twice within 3 seconds.
Button II for 2 seconds
Disarm & Pop Trunk Release
Press 2 seconds
Button I + II
Silent Arm / Disarm
Ignition in "off" position.
Button I + II for 2 seconds
Activate Anti Car-Jacking
Ignition in "on" position.
B. LED INDICATOR:
LED
Function
LED
Function
Off
Disarmed
2 flashes... pause
Trigger on trunk/hood
Slow flash
Armed
3 flashes... pause
Trigger on door switch
Fast flash
Passive arming
4 flashes... pause
Trigger on Dual Zone Shock Sensor
On (solid)
Valet mode
5 flashes... pause
Trigger on Ignition switch
C. CHIRP INDICATORS: D. PARKING LIGHT:
Chirp
Function
Parking light
Function
1 chirp
Arm
1 flash
Arm
2 chirps
Disarm
2 flashes
Disarm
3 chirps
Defective reminder
3 flashes
Disarm / Intrusion
4 chirps
Disarm / Intrusion
12 flashes
Car Locator
6 chirps
Car Locator
E. ALARM OPERATING CONDITION:
Siren
Parking Light
LED
Doors
Starter disable
Pager
1. Arming
1 Chirp
1 Flash
Slow flash
Locking
On
2. Disarming
2 or 4 Chirps
2 or 3 Flashes
Off or Fast
flash
Unlocking
Off
3. Trigger
Alarming
Flashes
Slow flash
On
On
4. Panic
Alarming
Flashes
Slow flash
Locking
On
F. ACTIVE ARMING –LOCK & ARM:
1. Press button I on transmitter.
2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The
vehicle’s door will lock upon arming when interfaced with the security system.
Note: Defective sensor reminder: If the siren sounds 3 chirps, then you have left a door, trunk, or hood
lid ajar. (See Feature “I - 3 Programming)
SILENT ARMING / DISARMING: Press the button I + II together on the transmitter will arm or disarm
your security system, No chirp sound will be heard, arm / disarm confirmation will be through the vehicles
parking lights only.
SHOCK SENSOR / OPTIONAL SENSOR BY-PASS: Press the button I on the transmitter twice within 3
seconds will arm the security system, by-pass the shock sensor and the optional sensor connected to 4
pin plug. The system will chirp one additional time to confirm the sensor bypass mode was activated. The
sensor bypass feature is programmed to activate for one arming cycle only. The security system will
return to normal operation during the next arming cycle.
G. PASSIVE ARMING: (See Feature “II - 2” Programming)
Active arming / disarming is controlling your security system via the remote transmitter. This security
system is equipped with an optional Passive Arming feature, which allows the security system to arm 30
seconds after the last door is closed. Operation is as follows.
1. Turn the ignition to the “OFF” position and exit the vehicle.

MEGA 462
9
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any
door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once the
vehicle all entrances are closed.
3. After 30-second time has elapsed, the security system will automatically “ARM”. The siren will chirp [1]
time and the parking lights will flash [1] time.
PASSIVE DOOR LOCKING: (See Feature “II - 2” Programming)
The vehicle’s door will automatically lock after passive arming cycle has been completed.
H. ACTIVE DISARMING –UNLOCK & DISARM:
1. Press the button II on the transmitter.
2. The siren will chirp twice and parking light will flash twice to indicating that the security system is now
disarmed. The vehicle’s door will unlock disarming when interfaced with the security system.
TAMPER DISARMING: If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash
3 times.
TWO STEP DOOR UNLOCK: (See Feature III –2 Programming.) This feature will independently unlock
the driver’s door only when disarming the security system. Pushing the button II on the transmitter two
times within 3 seconds will unlock the entire vehicle.
AUTOMATIC RE-ARM (See Feature “I - 2” Programming): If this feature is selected, the security system
will automatically re-arm itself 60 seconds after disarming with remote transmitter. Automatic rearm will
cancel if any door is opened before the 60 seconds timer has elapsed.
I. DISARMING WITHOUT A TRANSMITTER
The Override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Within 10 seconds push and release the valet switch
The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle
normally.
J. VALET MODE:
The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your
transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm
function are bypassed, however the remote panic feature and remote door lock will remain operational.
Enter Valet Mode:
1. Turn the ignition to “ON” position.
2. Push and hold valet switch for 2 seconds until the LED turns on. The LED will remain on as long as
the system is in 'valet mode.
Exit Valet Mode:
1. Return to normal operation, turn ignition 'ON'.
2. Push and hold valet switch for 2 seconds, The LED will turn off indicate the system are exiting the valet
mode.
K. PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency.
1. Press and hold the button I on the transmitter for 3 seconds. The alarm will immediately sound.
2. To stop the alarm, press and hold the button I or II on the transmitter, the panic mode will be turned
off immediately.
3. If the button is not pressed, the alarm will automatically stop after 30 seconds.
L. TRIGGER THE SYSTEM
When armed, your vehicle is protected as follows:
1. Light impact will trigger the warn-away signal. A long chirp from siren/horn.
2. Heavy impact / Doors open / Hood open / Trunk open / Turns on the ignition switch will trigger the
programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren and parking
lights will turn on to alerting of an intrusion for 30 seconds. Then it will stop and automatic reset and re-arm.
If the one of sensors or detectors still active, the alarm system will sound a maximum of 6 cycles of 30
seconds .
M. ANTI CAR-JACKING
Warning: If you don't need the anti car-jacking function in this alarm system, be sure to set anti
car-jacking feature “OFF”. This system is default setting all anti car-jacking “OFF”. (See Alarm Feature III
- 3 Programming.)
1. TRANSMITTER ACTIVATE THE ANTI CAR-JACKING:
Press and hold button I + II on the transmitter for 2 seconds while the vehicle’s ignition is ON.
The parking light will turn on for 1.5 seconds to indicate trigger the anti car-jacking.
2. DOOR SWITCH ACTIVATE ANTI CAR-JACKING:
It operate as below:
1. Turn the ignition switch to “ON” position, the system is armed.

MEGA 462
10
2. Once the system is armed, If you are forced from the vehicle, the system will active the anti
Car-jacking trigger when the door is opened and closed.
TRIGGER THE ANTI CAR-JACKING MODE:
3-timer circuits will function as follows:
First timer:
a. 50 seconds after the system has been triggered. The siren will start chirping for 15 seconds.
b. During this 15 seconds period of chirping, you will be alerting to push the valet switch once to turn off
the anti car-jacking feature.
c. If not, it will enter second timer anti car-jacking.
Second timer:
65 seconds after the system has been triggered. The siren starts alarming and the parking light starts
flashing.
Third timer:
90 seconds after the system has been triggered
a. The siren still alarming and the parking light flashing, and
b. The starter disable will activate to prevent the vehicle from starting.
c. It will remain active until the vehicle's battery power exhausted.
OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR-JACKING:
Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will stop and
the system disarmed
N. IGNITION CONTROL DOOR LOCKS. (See Feature II –3 Programming.).
If the vehicle’s door lock have been interfaced to the security system, the system will automatically lock
the vehicle's door when the ignition is turned “ON” and /or unlock the vehicle’s door when the ignition is
turned “OFF”.
O. TRUNK RELEASE. (See Feature III –2 Programming.).
Press and hold button II on transmitter for two seconds to remote control the trunk release or other electric
devices.
P. CAR LOCATOR
Under Arm situation press the button I on the transmitter to active car locator function. The siren will chirp
6 times. The parking light will flash 12 times, for you to easily locate your car.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions.
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.

MEGA 462
11

MEGA 462
12