meitav-tec ETN-24-PM-H-1S Safety guide

Meitav-tec Ltd (Contel group)
Tel: [phone] Fax: [phone]
www.meitavtec.com - [e-mail]
ETN-24-PM-H-1S
Owner’s Manual – Installation and Operating Instructions
Please read this manual carefully before installation and use.
Index
Wiring Connections 1
Operating Manual 2
Technician Settings 3
Meitav-tec Ltd (Contel group)
Tel: [phone] Fax: [phone]
www.meitavtec.com - [e-mail]
ETN-24-PM-H-1S
Owner’s Manual – Installation and Operating Instructions
Please read this manual carefully before installation and use.
Index
Wiring Connections 1
Operating Manual 2
Technician Settings 3

1. Wiring Connections
TERMINAL FUNCTION
OP Cool output – 3 wire (OPEN)
CL Cool output – 3 wire (CLOSE)
COM Cool output – 3 wire (COMMON)
C 24VAC
R 24VAC (RED)
W1 Heat
G Fan
1. Wiring Connections
TERMINAL FUNCTION
OP Cool output – 3 wire (OPEN)
CL Cool output – 3 wire (CLOSE)
COM Cool output – 3 wire (COMMON)
C 24VAC
R 24VAC (RED)
W1 Heat
G Fan

2. Operating Manual
2.1 Turning the thermostat ON
•Press the ON button to turn the thermostat ON.
•The word "ON" will appear on display.
2.2 Turning the thermostat OFF
•Press the OFF button to turn the thermostat OFF.
•The word "OFF" will appear on display.
2.3 Adjusting temperature
•Press the “+” or “-“ buttons - the set-point temperature will flash.
•Using the “+” and “-“ buttons adjust the set-point temperature.
2.4 Selecting modes
Press the MODE button to switch between the four modes:
•Cool
•Heat
•Cool/heat (auto-change over),
•Fan only.
2. Operating Manual
2.1 Turning the thermostat ON
•Press the ON button to turn the thermostat ON.
•The word "ON" will appear on display.
2.2 Turning the thermostat OFF
•Press the OFF button to turn the thermostat OFF.
•The word "OFF" will appear on display.
2.3 Adjusting temperature
•Press the “+” or “-“ buttons - the set-point temperature will flash.
•Using the “+” and “-“ buttons adjust the set-point temperature.
2.4 Selecting modes
Press the MODE button to switch between the four modes:
•Cool
•Heat
•Cool/heat (auto-change over),
•Fan only.

3. Technician Settings
3.1 Setting time for motor cycle
•Disconnect power to the thermostat and open the cover.
•Short jumper “D”.
•Close the thermostat and reconnect power.
•Using the “+” and “-“ buttons adjust time for the motor cycle. The number on the display
represents seconds and will be multiplied by 10. Example: “15” Æ15 X 10 = 150 seconds.
(range 10…250 seconds)
•Disconnect power to the thermostat and open the cover again.
•Open jumper “D”.
•Close the thermostat and reconnect power.
CDE CDE
Jumper
short
Jumper
open
3. Technician Settings
3.1 Setting time for motor cycle
•Disconnect power to the thermostat and open the cover.
•Short jumper “D”.
•Close the thermostat and reconnect power.
•Using the “+” and “-“ buttons adjust time for the motor cycle. The number on the display
represents seconds and will be multiplied by 10. Example: “15” Æ15 X 10 = 150 seconds.
(range 10…250 seconds)
•Disconnect power to the thermostat and open the cover again.
•Open jumper “D”.
•Close the thermostat and reconnect power.
CDE CDE
Jumper
short
Jumper
open