MELAG Cliniclave 45 User manual

Technical Manual
Cliniclave® 45
Cliniclave® 45 M
Large steam sterilizer
from software version 3.218
EN
Read this manual carefully and in the correct order before setting up and commissioning the device. The instructions in-
clude important safety information. You also receive a user manual with the device. Please store this manual and the
user manual carefully and in close proximity to the device. They represent a component of the product.
0197

Contents
Contents
1 General guidelines ...............................................................................................................................................................4
Symbols used ......................................................................................................................................................................4
Formatting rules...................................................................................................................................................................4
2 Installation requirements.....................................................................................................................................................5
Installation material..............................................................................................................................................................5
Installation location ..............................................................................................................................................................6
On-side connections for installation.....................................................................................................................................7
Space requirements...........................................................................................................................................................10
Safeguarding in accordance with EN 1717........................................................................................................................12
Checking the rotating field direction of the CEE socket.....................................................................................................12
System and network safety................................................................................................................................................13
3 Setup and installation ........................................................................................................................................................15
Dispatch / delivery .............................................................................................................................................................15
Removal from the packaging .............................................................................................................................................15
Installing Cliniclave 45 .......................................................................................................................................................19
Installing Cliniclave 45 M ...................................................................................................................................................26
4 Operational readiness........................................................................................................................................................34
Determining the delivery capacity and the conductivity of the reverse osmosis unit .........................................................34
Operational readiness........................................................................................................................................................35
Checking the pressure of the reverse osmosis unit...........................................................................................................36
Instructing the user ............................................................................................................................................................36
5 Settings and adjustment....................................................................................................................................................37
Setting the door hinge........................................................................................................................................................37
Aligning the door panels ....................................................................................................................................................37
Inserting the shelf ..............................................................................................................................................................38
Setting the display position ................................................................................................................................................38
Settings on the device .......................................................................................................................................................39
6 Frequently Asked Questions (FAQ)..................................................................................................................................41
What does the log name mean?........................................................................................................................................41
How to format a CF card on the computer correctly? ........................................................................................................41
How to integrate the device in a (practice) network?.........................................................................................................42
How do I determine the IP address or network setting of a computer (Windows 7/10)? ...................................................44
What do the terms IP address, subnetwork and DHCP mean?.........................................................................................44
How can I check the software version of the steam sterilizer? ..........................................................................................44
7 Technical tables .................................................................................................................................................................45
Feed water quality .............................................................................................................................................................45
Precision and drift behaviour .............................................................................................................................................46
Nominal value tolerances ..................................................................................................................................................47
Pressure-time charts..........................................................................................................................................................48

1 General guidelines
4
1 General guidelines
Read this manual carefully and in the correct order before setting up and commissioning the device. The
instructions include important safety information. You also receive a user manual with the device. Please
store this manual and the user manual carefully and in close proximity to the device. They represent a
component of the product.
Should the manual no longer be legible, is damaged or has been lost, you can download a new copy from
MELAG download centre at www.melag.com.
Symbols used
Symbol Explanation
Indicates a dangerous situation, which if not avoided, could entail slight to life-
threatening injuries.
Draws your attention to a situation, which if not avoided, could result in damage to the
instruments, the practice fittings or the device.
Draws your attention to important information.
Formatting rules
Example Explanation
see Chapter 2 Reference to another text section within this document.
Universal-
Program
Words or phrases appearing on the display of the device are marked as display text.

2 Installation requirements
5
2 Installation requirements
Installation material
The installation set (art. no. ME09027) for the water connection includes:
Qty. Article Art. no.
1 Siphon for Cliniclave series (incl. extension pipe) ME72420
1 Rubber seal 3/4'' for external water supply ME56950
1 Hose clamp ---
1 Hanger bolt M8x60 ---
Included in the scope of delivery of the steam sterilizer (and required for installation):
Qty. Article Art. no.
1 Water outlet hose (1.5 m) inc. 2 flat seals for Cliniclave45 ME86610
1 Water outlet hose (2.1m) inc. 2 flat seals for Cliniclave45M ME86620
The following additional material can be ordered as required:
Qty. Article Art. no.
1 Water tap 3/4” with safety combination ME37310
1 Water stop ME01056
The connection set*) for installation of the MELAdem56 reverse osmosis unit contains:
Qty. Article Art. no.
1 Feed water hose (PE hose, 1.3m, Ø10/8mm) ---
1 Outlet hose (PE hose, 0.7m, Ø6/4mm) ---
1 Permeate line (PE hose, 1m, Ø6/4mm) ---
1 Inlet hose (PE hose, 0.7m, Ø8/6mm) ---
1 Manometer for measuring the primary pressure in the pressure
tank
---
The connection set*) for installation of the MELAdem56M reverse osmosis unit contains:
Qty. Article Art. no.
1 Feed water hose (PE hose, 2m, Ø10/8mm) ---
1 Outlet hose (PE hose, 2m, Ø6/4mm) ---
1 Inlet hose (PE hose, 2m, Ø8/6mm) ---
1 Manometer for measuring the primary pressure in the pressure
tank
---
*) Only included in the scope of delivery of the steam sterilizer if a corresponding reverse osmosis unit is
included in the scope of delivery.
The required volume of feed water for immediate commissioning:
13 l (Cliniclave45), 20 l (Cliniclave45M) in accordance with EN285, Appendix B

2 Installation requirements
6
Installation location
WARNING
Failure to comply with the setup conditions can result in injuries and/or damage to the
steam sterilizer.
nThe steam sterilizer should only be setup, installed and commissioned by persons
authorised by MELAG.
nThe steam sterilizer is not suitable for operation in explosive atmospheres.
nThe steam sterilizer is conceived for use outside the patient area. The device should be
located a minimum of 1.5m radius away from the treatment area.
General requirements
Property Requirements of the installation location
Cliniclave45 Cliniclave45M
Clear width from the entrance of
the practice to the installation
location
min. 70 cm
Installation surface level and horizontal, in accordance with EN285: waterproof, collects or
deflects water running out of the steam sterilizer
Installation location interior of a building (dry and protected from dust)
Floor loading (normal operation) 332 kg | 83 kg per caster*)503 kg | 125.8 kg per caster**)
Floor loading (hydraulic
pressure test)
400 kg | 100 kg per caster*)610 kg | 152.5 kg per caster**)
Heat emission (at maximum
solid load and with an opened
door)
1.4 kW 2.0 kW
Ambient temperature 5-40 °C (ideal range 16-26 °C)
Sufficient ventilation of the room must be guaranteed.
Relative humidity max. 80 % at temperatures of up to 31 °C, max. 50 % at 40 °C
(decreasing in linear fashion in-between)
Altitude (star connection) max. 3000 m
Altitude (delta connection) max. 4000 m
Illumination in accordance with EN ISO 12100 and EN 1837
*) incl. MELAdem56
**) incl. MELAdem56 M
Steam egress can occur during operation. Do not set up the device in the immediate proximity of a smoke
detector. Maintain clearance from materials which could suffer damage from steam.

2 Installation requirements
7
On-side connections for installation
Necessary installation requirements for the connections (all dimensions in mm)
Siphon with extension
pipe
)
3)
3) 2)
A - Connection area for the inlet hose on the siphon
1) This specification applies to the use of an extension pipe (siphon and extension pipe included in the installation set).
2) The extension pipe can be cut to the desired length.
3) The type EA back-flow preventer (included in the kiwa connection set, art. no. ME86902) is only required in the Netherlands.
Mains supply
WARNING
Improper installation may lead to a short-circuit, fire, water damage or electrical shock.
This could result in serious injury.
nOnly have the device set up, installed and commissioned by people authorised by MELAG.
Implement the following safety measures when dealing with the cable and power plug:
uNever damage or alter the power plug or cable.
uNever bend or twist the power cable.
uNever remove the plug by pulling on the power cable. Always take a grip on the plug.
uNever place any heavy objects on the power cable.
uNever run the power cable over areas in which it could become trapped (e.g. doors or windows).
uNever lead the cable along a source of heat.
uNever use any nails, paper fasteners or similar objects to fix the cable.
uShould the power plug or cable suffer damage, switch off the device. The power cable or plug should
only be replaced by authorised technicians.

2 Installation requirements
8
Building-side requirements of the mains connection
Property On-site requirements
Cliniclave45 Cliniclave45M
Local requirements The electrical equipment must accord with DIN VDE 0100. A main switch (all-
pole) should be fitted outside the installation room. This must be marked as a
separator for the device and be easily accessible for the operator. The feed line
to the electrical connection must be laid separately from the distribution to the
device. Observe the clockwise rotating field!
Electrical power 10.5 kW 13.5 kW
Power supply (star
connection)
CEE socket (red)
with 3x380-415 V + N + PE, 16 A,
50/60 Hz, position PE: 6 h
CEE socket (red)
with 3x380-415 V + N + PE, 32 A,
50/60 Hz, position PE: 6 h
Building-side fuse
protection (star
connection)
A separate circuit with fuse (to
guarantee continued practice operation
during device sterilizer malfunction):
3x16 A, RCD 30 mA
A separate circuit with fuse (to
guarantee continued practice operation
during device sterilizer malfunction):
3x32 A, RCD 30 mA
Power supply (delta
connection)
CEE socket (blue)
with 3x220-240 V + PE, 32 A,
50/60 Hz, position PE: 9 h
CEE socket (blue)
with 3x220-240 V + PE, 63 A,
50/60 Hz, position PE: 9 h
Building fuses
(delta connection)
A separate circuit with fuse (to
guarantee continued practice operation
during steam sterilizer malfunction):
3x32 A, RCD 30 mA
A separate circuit with fuse (to
guarantee continued practice operation
during steam sterilizer malfunction):
3x63 A, RCD 30 mA
Length of the power
cable from the floor unit
1.8 m
Other Additional socket 230V 50Hz for leakage water detector (water stop),
MELAprint60 label printer or MELAprint42/44 log printer
Connection to a network socket / MELAprint 60 label printer
The installation in the floor unit requires a network cable of sufficient length.
The planned length of the network cable in the floor unit amounts to 60 cm with Cliniclave45 and 112 cm
with Cliniclave45M.
When selecting the length of a suitable network cable, take into account the additional length from the floor
unit to the peripheral device or network socket.

2 Installation requirements
9
Water connection
Requirements for the water connection
Cold water Feed water Wastewater
Connection in the
practice
To the cold water cut-off
valve (water inflow tap)
G3/4“
To a water treatment unit To a surface-mounted
siphon (included in the
installation set)
Length of the hose from
the floor unit
1.30 m -- 1 m
Installation height 55-65cm -- max. 55 cm (upper edge
of the siphon)
Min. flow pressure 1.5 bar at 8 l/min 0.5 bar at 5 l/min --
Recommended flow
pressure
2.5-6 bar at 8 l/min 2-4 bar at 5 l/min --
Min. static water
pressure
-- 2bar --
Max. static water
pressure
10 bar 5bar --
Max. throughflow volume -- -- short-term max. 9 l/min
Max. water temperature 20 °C (ideal 15 °C)1) -- short-term max. 90 °C
Water quality drinking water, water
hardness 4-12°dH (in
accordance with
EN285)2)
EN 285, Appendix B,
table B.1, max.
conductivity 5 µS/cm
--
Measures for protecting
the drinking water supply
None (internally secured
against backflow into the
drinking water supply by
an air gap in accordance
with EN1717, fluid
category class 5)
With MELAdem56/
MELAdem56M
none (internally secured
against backflow into the
drinking water supply by
an air gap in accordance
with EN1717, fluid
category class 5)
Other water treatment
treatment unit for
Additional protection
required in accordance
with EN1717, fluid
category class 5
--
Leakage water detector MELAG recommends the installation of a leakage water detector with a cut-off
valve (e.g. MELAG water stop).
PLEASE NOTE
Fit the outlet hose at a constant decline without kinks or sagging. In case of deviations to
the installation arrangements, consult with MELAG.
Failure to do so can result in malfunctions of the device.
1) The higher the temperature, the longer the operating times and the higher the water consumption.
2) Higher levels of water hardness necessitate the upstream installation of a water-softening unit.

2 Installation requirements
10
Space requirements
Space requirement for Cliniclave 45:
left: fore view, door hinge left
right: view from above, door hinge left (D1, D2) and door hinge right
Device dimensions Cliniclave 45
Width A 64 cm
Height device with floor unit B1158 cm
Height to door of steam sterilizer
(free area below the swivel range
of the door)
B285 cm
Depth C 91 cm
Min. clearance to the side of the
door hinge*)
D125 cm (opening angle 95°)
D275 cm (opening angle 170°)
Min. clearance to the side wall of
the floor unit
D38 cm
Min. clearance to the rear E 15 cm
Free space when door open fully F180 cm (opening angle 95°)
F270 cm (opening angle 170°)
Niche width required G197 cm (opening angle 95°)
G2147 cm (opening angle 170°)
Clearance of door to device rear
panel
H 140 cm (opening angle 95°)
Clearance of door to the wall I 152 cm (opening angle 95°)
*) With door hinge right, keep the clearances mirror-inverted (dotted line).
A free area of 60cm must be given each side of the steam sterilizer or must be achievable by moving the
steam sterilizer to facilitate maintenance.

2 Installation requirements
11
Space requirement Cliniclave 45M
left: fore view, door hinge left
right: view from above, door hinge left (D1, D2) and door hinge right
Device dimensions Cliniclave45M
Width A 64 cm
Height device with floor unit B1158 cm
Height to door of steam sterilizer
(free area below the swivel range
of the door)
B285 cm
Depth C 153 cm
Min. clearance to the side of the
door hinge*)
D125 cm (opening angle 95°)
D275 cm (opening angle 170°)
Min. clearance to the side wall of
the floor unit
D38 cm
Min. clearance to the rear E 15 cm
Free space when door open fully F1145 cm (opening angle 95°)
F2135 cm (opening angle 170°)
Niche width required G197 cm (opening angle 95°)
G2147 cm (opening angle 170°)
Clearance of door to device rear
panel
H 202 cm (opening angle 95°)
Clearance of door to the wall I 214 cm (opening angle 95°)
Sum of door width and floor width With a 90°curve at least 230 cm
*) With door hinge right, keep the clearances mirror-inverted (dotted line).
A free area of 60cm must be given each side of the steam sterilizer or must be achievable by moving the
steam sterilizer to facilitate maintenance.

2 Installation requirements
12
Safeguarding in accordance with EN 1717
The connection of the device to the water line is comparable with the connection of a washing machine in
a domestic context. In general, the connection of consumers to the drinking water supply should be per-
formed in accordance with EN1717, so that the drinking water supply is protected against contamination
through the possible flow back of the water. The device has been developed in accordance with all the re-
quirements of EN1717 and is equipped with an air gap in accordance with fluid category 5. This obviates
the need for additional protection from a safety combination consisting of a back-flow preventer and a pipe
aerator. If a safety combination is already present, the drinking water supply is subject to double protec-
tion; this need not be removed. If the device is supplied with feed water via the MELAdem56/
MELAdem56M reverse osmosis unit, EN1717 has been fulfilled, even in the absence of a building safety
system. The drinking water supply is protected, as the water treatment unit is supplied with water via the
air gap integrated in the device. If the device is supplied with feed water via a domestic network, the water
treatment unit requires protection via a protection unit in accordance with EN1717, fluid category 5. Com-
ply with your national regulations.
Checking the rotating field direction of the CEE socket
NOTICE
An incorrect rotating field can result in preservatives entering the device from the pump.
An opposite rotating field can cause malfunctions and damage to the device and practice
fittings.
nNever connect the device to the power supply without first having checked the rotating field
direction of the power supply. The device has been conceived exclusively for a clockwise
rotating field.
1. Check the direction of rotation of the high-voltage
current socket using a rotating field tester. The
mains socket must have a clockwise rotating field. If
this is not the case, commission a qualified
electrician to change the rotating field on the high-
voltage current socket.
2. If it is not possible to adapt it to the electric socket,
commission a qualified electrician to switch phases L2
and L3 in the high-voltage current plug (figure:
example Cliniclave45 star connection 16A).

2 Installation requirements
13
System and network safety
The device is fitted with multiple external interfaces. Comply with the following information pertaining to the
use of these interfaces to ensure safe operation of the device, especially to ensure incorporation in the lo-
cal network (LAN).
Interfaces and connections
NOTICE
Only connect the hardware to the device which is listed in the following table. Only use
the software which has been intended for the purpose and approved by the
manufacturer.
Interface Type Hardware Purpose/software
CF card slot CF type I MELAflash CF card up to 4GB with
an FAT16 or FAT32 file system
Writing log data on a MELAflash CF
card
MELAflash CF card up to 4GB with
a FAT16 file system
Device software update
Ethernet Ethernet
IEEE 802.3
Switch port
(via CAT-5 patch cable)
MELAview
saving log data, querying device
data
MELAtrace
saving log data
FTP server
saving log data
MELAconnect (mobile app)
querying device data
Connection to the local network
(LAN)
MELAprint60
(via CAT-5 patch cable)
Label print
MELAprint42/44
(via CAT-5 patch cable with network
adapter)
Log printing
NOTICE
When performing a device software update, use only the update data authorized by
MELAG for the corresponding device type.
Operating the device with memory media
To prevent data loss, only use memory media to save the log data with the following characteristics:
nFunctional capability (without malware etc.)
nWriteable
nFormatted with a correct file system
Perform regular data backup. Restrict access to the device and systems with access authorization to the
necessary circle of persons.

2 Installation requirements
14
Operating the device in the local network (LAN)
NOTICE
Do not connect the device to a public network (e.g. the internet).
An Ethernet/IP-based network connection (LAN) is required to operate the device in a local network. In its
delivery state, the device is configured to obtain the IP address automatically from a DHCP server operat-
ed in a LAN.
NOTICE
Check the IP address carefully during the conversion for a manual configuration before
connecting the device to the LAN.
An incorrectly-entered IP address can cause IP conflicts in the network and thus disturb
another device in your network.
In the LAN with a firewall, only permit connections to and from the device which correspond to the intend-
ed use of the device. All ports not used are blocked on the device side.
The device is able to make the following connections as standard:
Log Port source Port
destination
Direction Purpose
TCP ≥1025 21 Outgoing FTP control
TCP Any ≥1025 Listening / incoming FTP (active) data transfer (device set
to FTP logging)
UDP 68 67 Outgoing Communication to DHCP server -
requests to the DHCP server
UDP 67 68 Listening / incoming Answers from DHCP server(s)
TCP Any 80 Listening Data transfer to the MELAconnect app
or web browser
TCP Any 65001 Listening / incoming Data transfer log data (device set to
TCP logging)
UDP 17784 17784 Outgoing Broadcast search log printer
TCP 50001 50000 Outgoing Data transfer to log printer
UDP 42380 3000 Outgoing Broadcast search label printer
TCP 52382 - 53382 9100 Outgoing Data transfer to label printer
Network bandwidth / Quality of Service (QoS)
The device does not place any requirements on the LAN bandwidth for data transfer, that exceed the
standard time-out times of the respective logs.
Process Volume max. Volume normal
Transfer status, legend, program, malfunction log 10kB 2-6kB
System log 64kB --
Graphic log 800kB 580kB
Data transfer MELAconnect 240bit/s per device c. 200bit/s per device
Data transfer, web interface (browser) 12kbits/s per connection --

3 Setup and installation
15
3 Setup and installation
WARNING
Improper installation may lead to a short-circuit, fire, water damage or electrical shock.
This could result in serious injury.
nOnly have the device set up, installed and commissioned by people authorised by MELAG.
Dispatch / delivery
CAUTION
Danger of back injury and crushing from lifting excess loads.
nMELAG recommends carrying the device with at least six people.
Depending on the transport route and method, the device and the floor unit will be delivered either
screwed together or separately.
Method 1: Complete dispatch
The device is delivered on the floor unit as a single package. Comply with the separate instructions when
removing the transport packaging “Unpacking the complete dispatch package” (doc. AS_015-17).
Method 2: Separate delivery of device and floor unit
NOTICE
After having removed the packing hull, do not to contribute the device directly on the
floor; this could damage the hose connections and components on the underside of
device.
Transport the device and floor unit on the shipping pallet as close as possible to the installation location.
Only then place the two components on top of each other using the transport bars provided.
Removal from the packaging
This section indicates how to proceed when the floor unit and steam sterilizer have been dispatched
separately. If the steam sterilizer is delivered screwed to the floor unit, begin with step 8.
Cliniclave45
1. Remove the packaging from the steam sterilizer
and floor unit. Leave the steam sterilizer to stand on
the shipping pallet.
2. If possible, set up the floor unit directly at the
installation location.
3. Unscrew the four plastic screws from the front and
back of the side walls of the steam sterilizer.
4. Fit the two transport bars on the left and right-hand
side of the steam sterilizer each with 4 hexagonal
screws and 4 spacers. Tighten the screws fully.
5. Lift the steam sterilizer from the shipping pallet onto
the floor unit so that the device door and the floor
unit door face to the same side.

3 Setup and installation
16
6. Ensure that the four pins on the underside of the
steam sterilizer (marking) are guided into slots on the
floor unit. The power cable and the inlet hose must be
led into the floor unit and may not become jammed.
Align the steam sterilizer with the floor unit so that the
housing parts are flush along the side (use the
transport bars). The plastic fronts of the floor unit and
the steam sterilizer must also be aligned.
7. Working from below in the floor unit, tighten the
nuts with toothed lock washers (included in the
scope of delivery) to the pins, in order to screw the
floor unit and steam sterilizer together.
8. With separate delivery of steam sterilizer and
floor unit:
Remove the transport bars and retain them for later
use.
With a complete dispatch:
Unpack the device in accordance with the separate
set of instructions “Unpacking the complete
dispatch package” (doc. AS_015-17).
Remove the carrying handles and retain them for
later use.
9. Screw the four plastic screws in the location on
which the transport bars or carrying handless were
previously screwed in.
10. Connect the display, see Connecting the display
[}page18].
NOTICE
The housing screws can loose while transporting.
Tighten all housing screws.
Cliniclave45M
1. Remove the packaging from the steam sterilizer
and floor unit.
2. If possible, set up the floor unit directly at the
installation location.
3. Unscrew the four plastic screws from the front and
back of the side walls of the steam sterilizer. Do not
remove the plastic screws in the centre of the
device.
4. Fit the two transport bars left and right of the steam
sterilizer with four hexagonal screws and spacers.
Tighten the screws fully.

3 Setup and installation
17
5. Working with a minimum of six people, lift the
steam sterilizer from the shipping pallet onto the
floor unit so that the device door and the floor unit
door face to the same side.
6. Ensure that the six pins on the underside of the steam
sterilizer (marking) are guided into slots on the floor
unit. The power cable and the inlet hose must be led
into the floor unit and may not become jammed. Align
the steam sterilizer with the floor unit so that the
housing parts are flush along the side (use the
transport bars). The plastic fronts of the floor unit and
the steam sterilizer must also be aligned.
7. Working from below in the floor unit, tighten the
nuts with toothed lock washers (included in the
scope of delivery) to the pins, in order to screw the
floor unit and steam sterilizer together.
8. With separate delivery of steam sterilizer and
floor unit:
Remove the transport bars and retain them for later
use.
With a complete dispatch:
Unpack the device in accordance with the separate
set of instructions “Unpacking the complete
dispatch package” (doc. AS_015-17).
Remove the carrying handles and retain them for
later use.
9. Screw the four plastic screws in the location on
which the transport bars or carrying handless were
previously screwed in.
10. Connect the display, see Connecting the display
[}page18].
NOTICE
The housing screws can loose while transporting.
Tighten all housing screws.

3 Setup and installation
18
Connecting the display
1. Remove the display from the service hatch and
remove the packaging.
2. Connect the Ethernet cable of the device to the
display.
3. Slide the display into the fore long groove at the
device.
4. Guide both lateral display locking elements into the
same guide groove on the steam sterilizer.
5. Press the display downwards until you feel it
engaging. The display can be set at various
positions to permit ergonomic working, see Setting
the display position [}page38].

3 Setup and installation
19
Installing Cliniclave 45
Installing the steam sterilizer
PLEASE NOTE
To prevent water damage, MELAG recommends the use of a leakage water detector e.g.
the MELAG water stop.
1. Installing the leakage water detector (optional).
2. Lead the cold water inflow hose with Aqua-Stop
(pos.a) through the lower opening in the rear panel of
the floor unit to the outside and connect it to the
building cold water inflow.
a
b
c
d
3. Connect the outlet hose (pos.b) to the wastewater
fitting on the steam sterilizer using one of the seals
included in the scope of delivery. Place it in the
tensioning carriage (pos. c) and lead it through the
upper opening in the rear panel of the floor unit.
4. Connect the outlet hose to the siphon using the
other seal.
5. Lead the power plug (pos.d) through the lower
opening in the rear panel of the floor unit. Do not
yet plug the power plug into the mains socket.
Connecting the network cable (optional)
The network cable can be connected to a computer (in the practice network) or to the label printer.
1. Connect the network cable on the underside of the
device to the network socket (pos.a). Guide the
network cable in the floor unit over the cable clips.
a
2. Lead the power cable through the upper opening in
the rear panel of the floor unit to the outside.
3. Connect the network cable to the network socket/
the label printer (optional).

3 Setup and installation
20
Installing the MELAdem 56 (optional)
Proceed as follows to connect the reverse osmosis unit and prepare flushing:
1. Loosen the screws (TX20) (pos. a1/2) on the cover of
the osmosis module and pull the cover upwards.
Proceed with caution.
a1/2
2. Work carefully to remove the closure caps from the
hose connections on the underside of the steam
sterilizer. To do so, disconnect the union nuts. Store
the sealing caps carefully. They could be required for
transport or decommissioning.
3. Connect the feed water hose (pos.b), the outlet hose
(pos.c) and the inlet hose (pos.d) to the floor trough
connections of the steam sterilizer; see Installation
material [}page5] for the hose diameter and lengths.
d
cb
4. Remove the closure caps from the reverse osmosis
unit connections. Connect the outlet hose (pos.e), the
inflow hose (pos.f) and the permeate line (pos.g)
with the corresponding connections of the reverse
osmosis unit.
gfe