Meler MICRON NON STOP User manual

ADHESIVE
MELTER
MICRON NON
STOP
INSTRUCTIONS
MANUAL
MA-5147-ENG 151220
GLUING SOLUTIONS

Published by:
Focke Meler Gluing Solutions, S. A.
Pol. Arazuri-Orkoien, c/B, nº3 A
E-31170 Arazuri - Navarra - Spain
Tel.: + 34 948 351 110
e-mail: [e-mail]
www.meler.eu
Focke Group
Edition December 2020
© Copyright by Focke Meler
All rights reserved. Its reproduction, diffusion or use by electronic or other
means of all or any part of this document without the express authorization of
its owner is strictly prohibited.
The specifications and information contained in this manual may be modified
without prior notice.
The official language of this manual is only the English language. The
remaining versions of the manual in other languages are mere translations
without any official value or efficacy. In case of discrepancies or contradictions
between the English version of the manual and any other version of the manual
written in another language, the English version will prevail.

TABLE OF CONTENTS MA-5147-ENG MICRON NON STOP ADHESIVE MELTER
TABLE OF CONTENTS
1. SAFETY GUIDELINES 1-1
General 1-1
Symbols 1-1
Mechanical components 1-2
Electrical components 1-2
Hydraulic components 1-2
Pneumatic components 1-2
Thermal components 1-3
Materials 1-3
Noise emission declaration 1-3
Intended use 1-4
Limited use 1-4
2. INTRODUCTION 2-1
Description 2-2
Modes of operation 2-2
Hot-melt melter identification 2-3
Main components 2-3
Control card components 2-4
Pumping control card components 2-5
LOGO programmer 2-6
Micron Non Stop series range 2-6
3. INSTALLATION 3-1
Introduction 3-1
Installation requirements 3-1
Free space 3-1

FOCKE MELER GLUING SOLUTIONS TABLE OF CONTENTS
Electrical Consumption 3-2
Compressed air 3-3
Other factors 3-3
Unpacking 3-3
Contents 3-3
Mounting the equipment 3-4
Electrical power connection 3-4
Pneumatic connection 3-5
Hose and applicator connection 3-5
Parameter Programming 3-6
Programming working temperatures 3-6
Selecting the overheating value 3-7
Keeping a component on display 3-7
External I/O connections 3-8
Output disabled 3-10
4. MELTER OPERATION 4-1
General information 4-1
Filling the tank 4-2
Starting up the melter equipment 4-3
Melter equipment displays 4-3
Displaying the temperature for each component 4-4
Alarm displays 4-5
Display and adjustment of the cylinder working temperature 4-7
Display and adjustment of the working speed 4-7
Temperature adjustment 4-7
Programming the applicator parameters 4-8
Programming process 4-9
Timer to switch between ON - Standby - OFF modes 4-12

TABLE OF CONTENTS MA-5147-ENG MICRON NON STOP ADHESIVE MELTER
Password to access parameter programming 4-13
Total equipment service hours counter 4-13
Counter that warns of the need to change the adhesive agent filter 4-14
Setting the clock 4-15
Programming the current day and hour 4-15
Programming equipment activation/deactivation 4-16
Disabling the equipment activation/deactivation program 4-17
Programming the equipment’s standby function activation/deactivation 4-17
Disabling the equipment standby function programming 4-18
Special function buttons 4-19
Pumping control 4-20
Starting up the pump control card 4-20
Pumping safety measures 4-20
Password security 4-21
LED indicators 4-22
Modes of operation 4-23
Mode of operation with internal pumping control and internal speed control 4-23
Mode of operation with internal pumping control and external speed control 4-24
Mode of operation with external pumping control and internal speed control 4-25
Mode of operation with external pumping control and external speed control 4-26
User configuration menu 4-27
Displaying alarms and reset function 4-28
Maximum rpm alarm 4-28
Minimum rpm alarm 4-28
Variator alarm 4-28
Configuring speed ramp 4-29
Programming speed ramp 4-30
Current Vin voltage display 4-31
Start-up and automatic process 4-31