MELICONI CONTROL 2 Simple User manual

MELICONI remote control –CONTROL 2 Simple
TASTO
BUTTON
TV
TER / SAT
1
SAMSUNG
ADB –I.CAN / SKY
2
LG
TELESYSTEM
3
SONY
SAMSUNG
4
PANASONIC
METRONIC
5
SHARP
DIGIQUEST
6
PHILIPS
STRONG
7
TELEFUNKEN
HUMAX
8
MIVAR / UNITED
ID SAT / ZODIAC
9
TOSHIBA
COBRA
0
ALTRE MARCHE –OTHER BRANDS
Meliconi SpA,
Via Minghetti 10,
40057 Cadriano di Granarolo Emilia, (BO) Italy
web: www.meliconi.com
email: [e-mail]
The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the
end of its useful life the product must be collected separately from other waste. Therefore, at the end of the
device’s life, you must take it to appropriate centres for the differentiated collection of electrical and
electronic waste, or return it to the retailer when purchasing a new device of equivalent type, on a one-for-
one basis. Suitable differentiated collection to allow subsequent recycling of the decommissioned device,
with environmentally-compatible treatment and disposal, help to prevent any negative effects on the
environment and health and to promote the recycling of the materials of which the device is made.
BRAND RESEARCH REFERENCE TABLE

Thank you for choosing a Meliconi remote control.
The CONTROL 2 Simple remote control is designed to command a TV and a DECODER (satellite or digital terrestrial).
CONTROL 2 Simple is a simplified remote control; it provides ONLY the functions on the keypad.
IMPORTANT! When the remote control is set to control only the TV, all the buttons will control the TV; whilst when it is set to
control 2 devices (TV + DECODER), only the black buttons will control the TV, whilst the white buttons will control the
DECODER.
The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
The remote control requires 2 new 1.5V AAA/LR03 alkaline batteries, not included in the
package. Insert with the correct polarity as shown in figure.
DO NOT use rechargeable batteries.
BATTERIES TEST: Press and hold the ON/OFF [ ] button and check that the indicator light
remains on continuously until the button is released. If the light is off or blinks, the inserted
batteries are low, therefore they need replacement.
Before using the remote control, for each device you wish to control, it is essential to set a specific code, it matched.
Identify the specific code and set it into the remote control using one of the following ways:
www.meliconi.com/guide
Go to the website listed above, or use the qr-code on the side, to access online tool SEARCH
ACTIVATION CODE.
Once you have found the specifi c code for your device, set it in the remote control as described
in the ENTERING THE CODE DIRECTLY chapter.
BRAND
RESEARCH
MOBILE (SMS)
INTERNET
SETTING VIA INTERNET
ACTIVATION OF REMOTE CONTROL
Do not leave exhausted batteries inserted, as liquid may leak and damage the remote control
INSERTING THE BATTERIES
SAFETY WARNINGS
The remote control must not be exposed to excessive heat sources or fire.
The product is not a toy. Keep out of reach of children or domestic animals.
Keep this booklet for future reference

(only to be performed if you know the specific code to be set)
If you want to use CONTROL 2 Simple to control 2 devices at the same time (TV + DECODER) set firstly the code for the TV
and then the code for the DECODER. To control just one device, enter only the desired code.
•Press and hold on the MELICONI remote control for at least 6 seconds both [P +]e [+]
buttons for the TV setting (or [P +]e [P –]for DECODER setting).
•When the indicator light flashes, release and immediately enter the previously identified code.
(4 digits)
•Three final flashes indicate that the operation has been completed successfully.
(the service is free, the only cost being that of sending the SMS, which depends on your service operator fees)
Send an SMS as follows: 2N, Type, Brand, Model EXAMPLE
ATTENTION - separate the information with a comma and be as precise as possible so that the information system can
search for data and answer correctly.
Send the SMS to 0039 345 7518893 and wait for a reply by SMS.
Once you have received the SMS with the list of codes, set the first code (4 digits) in the remote control as described in the
ENTERING THE CODE DIRECTLY chapter.
After entering the code stand in front of the device already turned on press ON/OFF [ ] button on the MELICONI remote
control. If the device does NOT switch off, set the next code in the SMS list on the remote control and try switching the device
off again. Repeat the operation until the device switches off. When the device switches off, check that the other buttons are
also operating correctly. If they do, the remote control is ready to use.
Indicate the model of the device to be controlled, usually
shown on a label on the back of the device (if the model
is unknown, do not write anything after the brand)
Indicate the brand of the device to be controlled
Indicate the type of device to be controller,
using one of the following abbreviations only:
TV
TER (terrestrial decoder)
SAT (satellite decoder)
Fixed text which must always be included
SETTING VIA MOBILE (SMS)
If the remote control does NOT carry out the three final flashes, the setting is NOT successful; repeat the procedure.
If still unsuccessful, it means that the code is not included in the remote control, contact the customer service.
ENTERING THE CODE DIRECTLY
2N, TV, PHILIPS,
32PFL3614

If certain buttons do not work correctly, you are probably using an incorrect code destined for a very similar device; at this
point ignore the SMS list and consult the SETTING VIA BRAND RESEARCH chapter to find a more suitable code.
(only to be performed if the specific code could not be found)
CAUTION: the search procedure could take several minutes.
If you want to use CONTROL 2 Simple to control 2 devices at the same time (TV + DECODER) firstly search the code for the
TV and then the code for the DECODER. To control one single device only do what interests.
A) Look in the table at the beginning of the booklet, referring to the column relating to the type,
the brand of device which you wish to control, and note the corresponding number in the
BUTTON column. If the brand is not present using zero “0”. (example: TV SONY = 3)
B) Stand in front of the device to be controlled and make sure it is ON (not in stand-by).
If necessary, switch it on using the original remote control (if this is still working) or the buttons
present on the device itself. (on TVs they can be on the side or the top).
C) Press and hold on the MELICONI remote control for at least 6 seconds both [P +]e [+]
buttons for the TV setting (or [P +]e [P –]for DECODER setting).
D) When the indicator light flashes, release and immediately press the numeric button identified in
the table for a moment. EXAMPLE: 3
E) Pointing the remote control towards the device to be controlled, press and hold on the
MELICONI remote control the ON/OFF [ ] button.
CAUTION: you may have to keep the button pressed for a few minutes before the device
switches off.
F) When the device switches off, IMMEDIATELY RELEASE the button and press the [OK] button.
G) Three final flashes indicate that the operation has been completed successfully.
NOTE: During the search the indicator stops flashing and the remote control exits the search mode in the following
cases:
•if for 30 seconds the indicated button is not pressed or if another button is pressed.
•if the list of codes to find is terminated. In this case consult the www.meliconi.com/guide website or contact the
customer service.
ADDITIONAL CHECK
Check that the MELICONI remote control operates your device also with the other main functions; if it does not,
REPEAT the procedure from step B using the same brand number.
If, after various attempts, do not get a satisfactory result REPEAT the procedure from step B, using 0 (zero) as brand
number.
SETTING VIA BRAND RESEARCH
NOTE: If you don’t receive an SMS on your mobile phone or if the message says ERROR or NO CODE, it means the
system has not been able to process the data you have sent. Do not send another SMS, only use the SETTING VIA
BRAND RESEARCH procedure or contact the customer service.

IMPORTANT: sometimes, to switch on the TV, you must hold the [ALT]button and press the [TV]button.
Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad.
Certain functions can be accessed by keeping the [ALT]button pressed while pressing the button for the desired function
shown in the figure.
For example to get the BACK function, hold down the [ALT] button and press the [EXIT]button pointing the remote control
to the device.
The functions of the buttons described below are available only if they are also present on the original device
BUTTONS AND FUNCTIONS USE
ON / OFF -switches
the decoder ON and OFF
Numeric keypad
Volume control +/ –
TELETEXT button
MUTE - turns
sound OFF and ON
MENU - to
open the device MENU
For selecting an
external input source
For selecting the next
programm P+ or the
previous programm P–
Confirm selection
ON / OFF -switches the TV
OFF and in some cases ON
ARROWS used to
move around the MENU
Enables the secondary
remote control functions
Exits the MENU
BACK - goes back
by one step in the MENU
GUIDE - to
open the guide
ON TV - in some
cases switches ON the TV
for exiting TELETEXT and
returning to normal screen

If for remote control setup has been used the BRAND RESEARCH procedure, obtain and make a note of the code in use as
follows:
•Press and hold on the MELICONI remote control for at least 6 seconds both [P +]e [+]
buttons to extract the TV code (or [P +]e [P –]for DECODER code).
•When the indicator light starts flashing, release and immediately briefly press the [EXIT]button.
•After a pause of several seconds, the indicator light produces four sets of flashes, spaced out,
corresponding to the code to be obtained. Count the number of flashes. Each set of flashes
corresponds to one digit in the code. Ten flashes correspond to the digit zero “0”.
(example code obtained = 1701)
•Make a note of the code obtained on the label on the inside of the battery cover. You may need it
in future.
●IF THE REMOTE CONTROL IS NEW AND YOU CAN NOT MAKE IT WORK
Check that you have carried out all the settings procedures correctly. If necessary repeat them, following all the steps
indicated carefully.
The code set in the remote control is incorrect for the device that you want to control. Consult the www.meliconi.com/guide
website to fi nd the correct code for your device. Or try entering all the codes for the same brand shown on the website or
received via SMS one by one and check which one works.
●IF THE REMOTE CONTROL STOPS WORKING
Remove the batteries, press some buttons and insert NEW batteries. Make sure that the remote control is pointing at the
device without any obstacles between them.
Also try entering the code used to set the remote control again.
●IF SOME FUNCTIONS ARE NOT AVAILABLE ON THE REMOTE CONTROL
Usually the MELICONI remote control makes available only the present functions on his keyboard, provided they are
available also on the original remote control.
If some of the MAIN functions are not available, you are probably using an incorrect code. Find and set a more suitable code
as described earlier.
●HOW TO CHECK IF THE REMOTE CONTROL SENDS INFRARED SIGNALS
The human eye is not able to detect infrared signals; use a camera (even that of the mobile phone).
Aim the infrared LED located in front of the remote control (not the red LED above) and press and hold on the remote control
the ON/OFF [ ]button.
If you see through the camera, the LED light with short white / light blue flashes means that the remote control works and
emits infrared.
ATTENTION!
Most problems are caused by using insufficiently charged batteries.
We recommend checking them and, if necessary, replace them as shown in the INSERTING THE
BATTERIES chapter.
TROUBLESHOOTING
DISPLAY CODE IN USE

Consult the www.meliconi.com/guide website for more detailed information on the product and for the on-line tools to
activate the remote control quickly and easily.
IMPORTANT! When contacting technical support it is INDISPENSABLE that you communicate the BRAND and
MODEL of the device that you want to control and which MELICONI remote control you are using.
To contact an operator to call number [phone] or send an e-mail to: [email protected]
WARRANTY: 2 year
Always keep your sales receipt as proof of the validity of the product’s warranty. The warranty is voided if the product is
tampered with or used improperly.
CUSTOMER SERVICE