MELICONI TLC05 User manual

TLC05
Thank you for choosing a Meliconi remote control.
The TLC05 remote control is designed to command a THOMSON / TCL digital television sets.
The MELICONI remote control reproduces infrared signals corresponding to the original; the functions that operate in radio
frequency (e.g. voice commands and pointers) are not supported.
The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
The remote control requires 2 new 1.5V AAA/LR03 alkaline batteries, not included in the
package. Insert with the correct polarity as shown in figure.
DO NOT use rechargeable batteries.
BATTERIES TEST: Press and hold the 5button and check that the LED remains on
continuously until the button is released. If the light is off or blinks, the inserted batteries are low,
therefore they need replacement.
If the remote control can not control the TV correctly, it is essential to set a specific code, it matched.
Identify the specific code and set it into the remote control using one of the following ways:
MANUAL
SEARCH
SMARTPHONE
TABLET - WEB
ACTIVATION OF REMOTE CONTROL
Do not leave exhausted batteries inserted, as liquid may leak and damage the remote control
INSERTING THE BATTERIES
SAFETY WARNINGS
The remote control and batteries should not be exposed to excessive heat such as sunlight, fire
or the like.
The product is not a toy. Keep out of reach of children or domestic animals.
This remote control, after inserting the batteries, is normally ready for use as it is already set at the
factory with a specific code.
If problems are found to command the TV, or some functions do not produce the desired effect, to follow the instructions
to the chapter ACTIVATION OF REMOTE CONTROL.
Keep this booklet for future reference
Remote control for TV sets THOMSON / TCL ready to use

Use the qr-code on the side or connect to the www.cme.it page and follow the instructions.
Once you have found the specific code for your device, set it in the remote control as described in the
ENTERING THE CODE DIRECTLY chapter.
•Stand in front of the device to be controlled and make sure it is ON (not in stand-by). If necessary, switch
it on using the original remote control (if this is still working) or the buttons present on the device itself. (on
TVs they can be on the side or the top)
•On the MELICONI remote control press and hold the button until the LED of the remote control lights
up; release.
•Pointing the remote control towards the device, PRESS AND HOLD the ON/OFF button and wait
for the device to switch off.
•PAY ATTENTION, when the device turn off, IMMEDIATELY RELEASE the button.
•Three final flashes indicate that the operation has been completed successfully.
(only to be performed if you know the specific code to be set)
•On the MELICONI remote control press and hold the button until the LED lights up; release.
•Immediately enter the previously identified specific code.
•Three final flashes indicate that the operation has been completed successfully.
If you want to delete the function in combination with a single button, operate as follows:
•On the MELICONI remote control press and hold the button.
•When the LED turn on, without releasing the button, enter the code 1600; release the buttons.
• Within 30 seconds, press and hold the button of which you want to delete the function; wait three flashes indicating the end
of the operation, release the button. (to recall the original function, setting again the activation code)
DELETE FUNCTION BY SINGLE BUTTON
If the remote control does NOT carry out the three final flashes, the setting is NOT successful; repeat the procedure.
If still unsuccessful, it means that the code is not included in the remote control, contact the ASSISTANCE.
ENTERING THE CODE DIRECTLY
VERIFY
Check that the MELICONI remote control operates your device in the main functions; if it does not, REPEAT the
procedure.
NOTE: When the list of codes to be searched is over, the remote control exits the search and the LED remains off.
If after 2attempts no results are obtained, try using the procedure described in the SMARTPHONE - TABLET - WEB
chapter or contact the ASSISTANCE.
MANUAL SEARCH
SMARTPHONE - TABLET - WEB
watch
the video
watch
the video

The functions of the buttons on the MELICONI remote control are only available if the original device is equipped with it.
Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad.
To enable them, connect to the www.cme.it page, use the on-line tool ACTIVATION OF REMOTE CONTROL and continue
until you see the list matching buttons between the original remote control and the MELICONI remote control.
If the function you want to play is matched with an number in orange color, operate as follows:
•On the MELICONI remote control press and hold the button.
•When the LED turn on, without releasing the button, point the remote control towards the device
and enter the previously identified number corresponding to the function you want to get. (at the last digit
pressure, the remote control already transmits this function)
•Release the buttons; to match the function obtained to a MELICONI remote control button, within 30
seconds, press and hold the desired button.
•Wait three flashes indicate that storage; release the button. (the used button loses the original function
that will be called by setting again the activation code)
For any future activation of the remote control, it is advisable to extract and note the code in use, operate as follows:
•On the MELICONI remote control press and hold the button until the LED lights up; release.
•Enter the code 0010.
•After a pause of several seconds, the LED produces four sets of flashes, spaced out,
corresponding to the code to be obtained. Count the number of flashes. Each set of flashes
corresponds to one digit in the code. Ten flashes correspond to the digit zero “0”.
(example code obtained = 1701)
•Make a note of the code obtained. You may need it in future.
If necessary it is possible to completely reset the remote control and bring it back to the initial conditions.
WARNING : All user settings will be lost. Operate as follows:
•On the MELICONI remote control press and hold the button until the LED lights up; release.
•Enter the code 0100.
•Three final flashes indicate that the operation has been completed successfully.
web: www.cme.it e-mail: [email protected]
IMPORTANT! To obtain technical assistance, it is essential to indicate the BRAND and MODEL of the appliance you intend
to control and the name of the MELICONI remote control you are using.
ASSISTANCE
RESET THE REMOTE CONTROL
DISPLAY CODE IN USE
BUTTONS AND FUNCTIONS

●IF THE REMOTE CONTROL IS NEW AND YOU CAN NOT MAKE IT WORK
It is possible that the code set in the remote control is incorrect for the device that you want to control. Check that you have
carried out all the settings procedures correctly. If necessary repeat them, following all the steps indicated carefully.
Consult the website www.cme.it to identify the specific code associated with your device or contact the ASSISTANCE.
●IF THE REMOTE CONTROL IS NO LONGER ABLE TO CONTROL THE DEVICE
Disconnect the device from the electric socket and leave it without power for a few minutes; switch the device on again.
Remove the batteries from the remote control, press the ON/OFF button twice and insert NEW batteries.
Make sure that the remote control is pointing at the device without any obstacles between them.
If necessary try to the RESET THE REMOTE CONTROL and carry out a new activation.
●IF SOME FUNCTIONS ARE NOT AVAILABLE ON THE REMOTE CONTROL
If some of the MAIN functions are not available, you are probably using an incorrect code. Find and set a more suitable code
as described in the ACTIVATION OF REMOTE CONTROL chapter.
Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad.
To enable them, operate as described in the BUTTON AND FUNCTIONS chapter.
●HOW TO CHECK IF THE REMOTE CONTROL SENDS INFRARED SIGNALS
The human eye is not able to detect infrared signals; use a camera (even that of the mobile phone).
Aim the infrared LED located in front of the remote control (not the red LED above) and press and hold on the remote control
the 5button.
If you see through the camera, the LED light with short white / light blue flashes means that the remote control works and
emits infrared.
WARRANTY: 2 year Always keep your sales receipt as proof of the validity of the product’s warranty. The warranty is
voided if the product is tampered with or used improperly.
Meliconi SpA, Via Minghetti 10 - 40057 Cadriano di Granarolo Emilia, (BO) Italy
web: www.meliconi.com email: [e-mail]
The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the
end of its useful life the product must be collected separately from other waste. Therefore, at the end of the
device’s life, you must take it to appropriate centres for the differentiated collection of electrical and electronic
waste, or return it to the retailer when purchasing a new device of equivalent type. Suitable differentiated
collection to allow subsequent recycling of the decommissioned device, with environmentally-compatible
treatment and disposal, help to prevent any negative effects on the environment and health and to promote
the recycling of the materials of which the device is made.
CAUTION: Batteries must not be disassembled, thrown into fire or released into the environment. Improper
use can cause damage to the environment and health. The symbol of the bins, indicating that the batteries
should be disposed of according to current regulations; inquire on collection of spent batteries and
accumulators in force in your country.
ATTENTION!
Most problems are caused by using insufficiently charged batteries.
We recommend checking and replace them as shown in the INSERTING THE BATTERIES chapter.
TROUBLESHOOTING (F.A.Q.)