MELICONI FACILE LIGHT User manual

USING THE KEYS AND FUNCTIONS
The functions described below are only available if
they are already foreseen by your TV.
SET-UP
Read these instructions carefully before
programming your remote control!
The F A C I L E L i g h t replacement remote control was designed as a TV control. Thanks to its large
database and numerous functions it is ideal for replacing any lost, defective or broken remote control.
Its ergonomic form and casing in soft rubber make it easy to grip and protect it against falls and bumps.
The large pushbuttons are easy to see and to use. And thanks to the LIGHT button the keys light up so
you can use the remote control even in the dark.
Thank you for choosing a MELICONI remote control.
F A C I L E L i g h t
Keep your Instruction Booklet and Code Booklet for future reference. For anyone with internet,
via the website www.gumbodylight.com, it is even easier and quicker to programme the remote
control and discover all the potential of the FACILE Light thanks to the on-line guide.
Light indicator
TV ON/OFF button
Teletext keys
Number keys
Confirm button
To select an external input terminal
Control the volume using +/–To select the next (P+) or
previous (P-) channel or programme
MUTE key
turns the volume on and off
Fastext functions
or to select submenus
by means of the colours
To move around within the MENU
or to control BRIGHTNESS/COLOUR
Key with additional TV functions To access the MENU
LIGHT button
to light up the keys
Impact-proof rubber casing
GB
7

To programme the F A C I L E L i g h t remote control,
follow the indications in paragraph A ,
B
or C .
1. Switch on the TV.
2. Look for the brand of your TV in the code book and make
a note of the code indicated alongside (
e.g. PHILIPS 0025 )
or the code for the brand indicated by the arrow.
3. Hold down the MUTE and ON/OFF buttons together for
5 seconds until the light indicator at the top starts to flash
indicating that the remote control is being programmed.
4. Release the buttons and enter the brand code previously
identified (
e.g. 0025 ) within 12 seconds.The light indicator
flashes more quickly to indicate that the remote control
is ready for the search.
5. Point the remote control at the TV. Press and slowly release
the ON/OFF key several times, stopping when the TV
goes off.
6. When the TV goes off, press the OK key to confirm. Three
flashes indicate that the operation has been completed
correctly.
The quickest and easiest way to programme the remote control
is by consulting the website www.gumbodylight.com.
BRAND SEARCH PROGRAMMING MODE
A
PHILIPS 0025
PHONOLA
PHILIPS
+++
FITTING THE BATTERIES
Before programming and using
the remote control, fit the batteries.
The remote control requires 2 new AA/LR06 batteries. Insert the batteries as shown:
• Remember to replace the batteries once a year.
• If the light indicator starts to flash while using the remote
control, replace the batteries. The batteries are low.
• When you remove the batteries, fit the new ones within
5 minutes or you may have to reprogramme your remote
control.
• Make a note of the code for your TV on the adhesive label
inside the battery cover in case you have to reprogramme
your remote control.
+5 SEC.
ADDITIONAL CHECK
Check that some of the other keys, corresponding to those on your original remote control, work correctly.
If the commands function incorrectly or erratically, you have probably entered a code for a similar remote
control but not the right one. In this case, repeat the search procedure starting from point 3 , entering the
code previously used (e.g. 0025).
8

To display and make a note of the code memorized by means of the search,
follow the instructions described in the paragraph CURRENT CODE DISPLAY.
ADDITIONAL CHECK
Point the remote control at the TV. Check that the TV responds correctly to the commands given. If there
is no response or the TV only responds partially or incorrectly, it is probable that you have used the wrong
code. In this case, repeat the procedure starting from point 3. This time, however, use the NEXT CODE
in the list (e.g. 1006).
The quickest and easiest way to programme the remote control
is by consulting the website www.gumbodylight.com.
DIRECT CODE ENTRY
B
1 . Switch on the TV.
2 . Look for the brand of your TV in the code book and
make a note of the first code in the list (e.g. Philips
1000).
3 . Hold down the MUTE and ON/OFF buttons together for
5 seconds until the light indicator at the top starts to
flash indicating that the remote control is being
programmed.
4 . Release the buttons and enter the 4-digit brand code
previously identified (e.g. 1000) within 12 seconds.
Three flashes indicate that the code has been
memorized correctly. If not, try the code entry procedure
again, starting from point 3 .
PHILIPS 0025
TV 1000 1006 1007 1008
1009 1010 1011 1012 1013
1014 1015 1016 1017 1018
Remember to make a note of the TV code used to programme
the remote control on the adhesive label inside the battery cover
for quick and easy reprogramming.
N.B. THE LIGHT INDICATOR STOPS FLASHING
The remote control exits programming mode and the light indicator stops flashing:
• if no keys are pressed for 14 seconds
• if an invalid code is entered
N.B. THE LIGHT INDICATOR STOPS FLASHING
The remote control exits programming mode and the light indicator stops flashing:
• if no keys are pressed for 14 seconds
• if an invalid brand code is entered
• if the end of the code search list has been reached. In this case, switch to programming mode C.
+++
1000
+5 SEC.
9

GLOBAL SEARCH REMOTE CONTROL PROGRAMMING
C
This operation can take up to 20 minutes and should be carried out if you have not
succeeded in programming the remote control by means of the other methods.
The quickest and easiest way to programme the remote control is
by consulting the website www.gumbodylight.com.
To display and make a note of the code memorized by means of the search,
follow the instructions described in the paragraph CURRENT CODE DISPLAY.
1 . Switch on the TV.
2 . Hold down the MUTE and ON/OFF buttons together for
5 seconds until the light indicator at the top starts to
flash indicating that the remote control is being
programmed.
3 . Release the keys and enter the code 0000 within 12
seconds. The light indicator flashes more quickly to
indicate that the remote control is ready for the search.
4 . Point the remote control at the TV. Press and slowly
release the
ON/OFF key several times, stopping when
the TV goes off.
5 . When the TV goes off, press the OK key to confirm.
Three flashes indicate that the operation has been
completed correctly.
ADDITIONAL CHECK
Check that some of the other keys, corresponding to those on your original remote control, work correctly.
If the commands function incorrectly or erratically, you have probably entered a code for a similar remote
control but not the right one. In this case, repeat the search procedure starting from point 2 .
+++
0000
N.B. THE LIGHT INDICATOR STOPS FLASHING
The remote control exits programming mode and the light indicator stops flashing:
• if no keys are pressed for 14 seconds
• if the end of the code search list has been reached. In this case, consult our website
www.gumbodylight.com
+5 SEC.
10

CURRENT CODE DISPLAY
To find out the code of your remote control, follow this procedure:
1
. Hold down the MUTE and ON/OFF keys together for 5
seconds until the light indicator at the top starts to
flash.
2 . Release the MUTE and ON/OFF keys and press and
release the
1-/-- key within 8 seconds.
3 . After a few seconds, the light indicator produces 4
series of flashes, with a pause between each series,
corresponding to the current code. Count the number
of flashes; each series of flashes corresponds to one
figure in the code. 10 flashes correspond to 0 .
4 . Make a note of the code on the adhesive label inside
the battery cover for quick and easy future
reprogramming.
+5 SEC.
........................................................ = 1
............................................ = 3
= 0
.......................... = 6
Code obtained = 1306
N.B. this operation cannot be interrupted and the remote control cannot
therefore be used until the end of the 4 series of flashes.
LIGHT FUNCTION: Lights up the keys on the remote control
Press the LIGHT button to light up the remote control keys. This is very useful in the dark to find
which key to press.
The light goes out when the LIGHT button is pressed again or after about 10 seconds if no keys are
pressed.
HOW TO USE THE ADDITIONAL COMMANDS WHICH DO NOT APPEAR ON THE KEYPAD
Find them on your F A C I L E L i g h t remote control by pressing the buttons one by one and discovering
the commands that interest you.
In particular, the additional functions most frequently used, such as NORMALIZATION , COLOUR and BRIGHTNESS ,
can be found on the following keys:
Normalization:
Brightness (+): or
Brightness (-): or
Colour (+): or
Colour (-): or
Although not indicated on the keypad,
some keys can be used for additional commands.
For less frequently used functions look for the additional commands on our website www.gumbodylight.com .
As well as easily finding the code to programme your remote control, the on-line guide will help you to
find which keys on the F A C I L E L i g h t remote control correspond to the additional commands.
11

PROBLEM SOLVING
INFO-LINE
If you have any queries about your F A C I L E L i g h t remote control:
• read this Instruction Booklet carefully - you will find an answer to most of your questions
• consult our website www.gumbodylight.com where you will find the answers you need easily and
quickly.
WARRANTY: 2 years
The warranty ceases to be valid if the product
is tampered with or used incorrectly.
Type of remote control GumBody Light
Model FACILE Light
Purchase date / /
Dealer’s stamp
The symbol of the crossed trash can shown on the remote control indicates that once the product has reached the end of its working life it
should be disposed of separately from other waste. The user should, therefore, take the remote control to a specialised collection centre
for electronic and electrical waste, or hand it over to the dealer when purchasing a new similar remote control, on a one to one basis. Correct
separated collection for subsequent recycling, processing and environmentally compatible disposal contributes in preventing possible
negative effects on the environment and on health and favours the recycling of the materials used in producing the remote control. Improper
disposal of the product by the user leads to application of the penalties as per legislative decree no. 22/1997 (article 50 and following of
decree no. 22/1997).
SOLUTION
Try some of the other frequently-used buttons. If
the problem persists, check that the batteries are
fitted correctly. If necessary, replace them with 2
new 1.5 V AA/LR06 batteries.
Check that the batteries are new and that the remote
control is pointing at the TV without any obstacles
in the way. If necessary, re-enter the remote control
code, following the programming procedure Aor
Bor C.
The batteries are low. Change them.
You may have used the wrong code. Re-enter the
remote control code, following the programming
procedure Aor Bor C.
Programme the remote control following the global
search procedure Cor consult the on-line guide
on the website www.gumbodylight.com to find
the code with which to programme your remote
control.
PROBLEM
The TV does not respond and the light indicator
does not light up when a key is pressed.
The TV does not respond but the light indicator
does light up.
The light indicator flashes when a key is held
down but the TV does not respond
.
The remote control commands are not all
working correcting.
The code for your TV brand is not in the Code
Book.
12