Melitta Solo & Perfect Milk User manual

DEGBFRNL
IT
ESDKSENO
FI
RUPLTRLTEELVCZCNKR
Bedienungsanleitung / Operating Instructions / Mode d'emploi
Gebruiksaanwijzing / Istruzioni per l’uso / Manual de instrucciones
Betjeningsvejledning / Bruksanvisning / Bruksanvisning / Käyttöohje
Руководство по эксплуатации / Instrukcja obsługi / Kullanma kılavuzu
Naudojimo instrukcija / Kasutusjuhend / Lietošanas instrukcija
Návod k obsluze / 操作手册 / 사용 설명서

2
1
11
10
9
5
6
7
A
2
8
14
13
4
312

3
B C
DE
F
1
4
5
6
2
3

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08
18
Safety Instructions
GB
Safety Instructions
Please carefully read and
comply with the operating
instructions.
This appliance is for the
preparation of coffee drinks
from coffee beans and for
heating milk and water.
This appliance is intended for
private domestic use.
Any other use is considered
contrary to intended use and
may lead to personal injury and
material damage.
This appliance complies with the
applicable European guidelines.
It has been built according to the latest
technology. However, there are residual
hazards.
To prevent hazards, you must follow
the safety instructions.
Melitta shall not be liable for any
damage caused by non-compliance
with safety instructions.
WARNING
Electrical current poses a
hazard!
Risk of injury due to electrical
shock if the appliance or power
cable is damaged.
To avoid hazards caused by
electrical current:
▶Do not use a damaged power
cable.
▶A damaged power cable
may only be replaced by the
manufacturer, their after sale
service or a similarly qualified
person.
▶Do not open any screwed covers
on the appliance housing.
▶Only use the appliance if it is in
a technically faultless condition.
▶A defective appliance may only
be repaired by an authorised
workshop. Do not attempt to
repair the appliance yourself.
▶Do not make any changes to the
appliance, its components and
its accessories.
▶Do not immerse the appliance
in water.
▶Do not let the power cable come
into contact with water.

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08 19
General safety
GB
WARNING
Burn injuries and scalding!
Released fluids and steam can be
very hot. Parts of the appliance
also become very hot.
To prevent scalding and burns:
▶Avoid skin contact with the
released fluids and steam.
▶Do not touch any nozzles on the
outlet during operation.
General safety!
To prevent personal injury and material
damage:
▶Do not operate the appliance in a
cabinet or similar object.
▶Do not reach into the interior of the
appliance when it is in operation.
▶Keep the appliance and power cable
away from children younger than
8 years of age.
▶The appliance can be used by children
from an age of 8 as well as by persons
with limited physical, sensorial or mental
capacities, or lacking experience and
knowledge if they are supervised or
were instructed on safe use of the
appliance and understand the resulting
risks.
▶Children may not play with the
appliance. Children younger than
8 years of age may not perform cleaning
and user maintenance. Children over
8 years of age must be supervised
during cleaning and user maintenance.
▶Disconnect the appliance from the
power supply if it is unsupervised for a
longer period of time.
▶Do not operate the appliance at high
altitudes over 2000 m.
▶When cleaning the appliance and
its components, comply with the
instructions in the corresponding
chapter ("Cleaning and maintenance",
page 25).
At a glance
Figure A
1Drip tray with cup plate and coffee grounds container as well as dis-
play for full drip tray
2 Height-adjustable outlet
3ON/OFF button
4 Coffee quantity regulator
5Button for coffee dispensing
6Button for coffee strength
7 Water tank
8 Bean container
9Button for steam dispensing
10 Display
11 Valve for milk froth and hot water
dispensing
12 Steam pipe
13 Cappuccinatore
14
Right cover (removable, covering
the grinding fineness adjustment
element, brewing unit and
identification label)

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08
20
Before using for the first time
GB
Figure F
1 Air intake valve
2 Air intake pipe
3 Control dial
4 Connection for milk hose
5 Connecting piece
6 Milk froth / hot water nozzle
Symbol on the Cappuccinatore
selection switch
Setting for warm milk
Setting for hot water
Setting for milk froth
Display
Lights up The appliance is ready
for operation.
Flashes Appliance is heating up or coffee is being
dispensed.
Lights up Change the Melitta® PRO AQUA filter
cartridge
Flashes Filter change in pro-
cess
Lights up Fill the water tank
Flashes Insert the water tank
Lights up Empty drip tray and coffee grounds con-
tainer
Flashes Insert the drip tray and coffee grounds
container
Lights up 1 bean: mild 2 beans: normal
3 beans: strong
Flashes
Fill bean container;
flashing stops after
dispensing the next
coffee.
Lights up Cleaning the device
Flashes Integrated cleaning
programme is running
Lights up Descale the appliance
Flashes Integrated descaling
programme is running
Lights up
Froth standby
or:
Air is in the system.
Turn valve switch 11
clockwise until the
stop until water flows
out of the appliance.
Flashes Milk froth or hot water
dispensing in process.

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08 21
Before using for the first time
GB
Before using for the first time
Check the scope of supply
Use the following list to check the
completeness of the delivery. Please
contact your retailer if there are missing
parts.
–Cappuccinatore
–Milk hose
–Test strips to determine water hardness
General information
■Only use pure water without
carbonation.
■Use the supplied test strip to determine
the hardness of the water used and set
the water hardness ("Water hardness
and filter", page 24).
■If you wish to use a water filter, do not
insert it until after the initial startup.
Information for using for
the first time
The appliance must be vented before it
is used for the first time. The appliance
may only be powered on with a completely
filled water tank.
■Push the Cappuccinatore 13 onto the
steam pipe up to the stop 12.
■Place a vessel under the
Cappuccinatore 13.
■Press the button to switch on
the appliance.
illuminates on the display.
■Turn the valve switch 11 clockwise
until it stops. flashes on the display.
Water will flow into the vessel.
■When is illuminated on the display,
turn the valve switch 11 anticlockwise
until it stops.
■The device is ready for operation.
■After initial startup, insert the Melitta®
PRO AQUA filter cartridge, if necessary
(see page 24).
Starting up the appliance
Commissioning
WARNING
Danger of fire and electric shock
due to incorrect supply voltage,
incorrect or damaged connections
and power cable!
▶Ensure that the supply voltage
corresponds to the supply voltage
specified on the identification label of
the appliance. The identification label is
located on the right side of the appliance
behind the cover (Image A, 14).
▶Make sure that the power socket meets
the applicable standards for electrical
safety. If in doubt, contact a qualified
electrician.
▶Never use damaged power cables
(damaged insulation, bare wires).
■Place the appliance on a stable, dry and
level surface with sufficient clearance
(at least 10 cm) to the sides.
■Push the Cappuccinatore 13 onto the
steam pipe 12 as far as it can go.
■Plug the power cable into a suitable
power socket.
■Remove the lid from the
bean container 8.
■Fill the bean container with suitable
coffee beans.
■Put the lid back on.
■Lift up the lid of the water tank 7and
pull the water tank up and out of the
appliance.

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08
22
Preparation
GB
■Fill the water tank with fresh tap water
only up to the max. mark.
■Insert the water tank into the appliance.
■Place a vessel under outlet 2.
■Press the on/off button to turn the
appliance on or off. The appliance may
perform an automatic rinse.
Preparation
■Fill the water tank with fresh water every
day. The water tank must always be
filled with enough water for the operation
of the appliance.
■Fill the bean container preferably with
espresso beans or bean mixtures for
fully automatic coffee machines.
Do not use any ground, glazed,
caramelised, or otherwise sugar-coated
coffee beans.
Setting the dispensed quantity and
strength
■Turn the coffee quantity regulator 4to
infinitely adjust the dispensed quantity.
Regulator all the way to the left
= 30 ml per cup
Regulator all the way to the right
= 220 ml per cup
■Press the button until the desired
strength is adjusted. The strength is
shown by the beans on the display 10
(from = mild to = strong).
Dispensing coffee or espresso
One or two cups can be dispensed
simultaneously.
■Switch on the device.
■Place one or two cups under the outlet.
■Preparing one cup: Press the
button once.
■Preparing two cups: Press the
button twice.
■Press the button again to cancel the
coffee dispensing.
Preparing milk froth and heating
milk and water
WARNING
There is a risk of burn injuries and
scalding due to hot steam and the
hot steam pipe!
▶Never reach into the escaping steam.
▶Avoid direct skin contact with hot water
and the hot steam pipe.
▶Never touch the steam pipe during
use or immediately after use.
The Cappuccinatore is used to prepare
milk froth, to heat milk or to dispense hot
water.
It can froth the milk directly from the milk
carton or a vessel into the cup.
You can optionally connect it to a
Melitta®milk container.

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08 23
Preparation
GB
Preparing milk froth
If possible, use cold milk with a high
protein content.
■Switch on the device.
■Submerse the Cappuccinatore hose 13
directly into the milk.
■Press the button. flashes while
the appliance is heating up. After the
heat-up phase, is illuminated.
■Turn the control dial (Image F, 3) to the
"Milk froth" position ( is pointing up).
■Turn the valve switch 11 clockwise until
the stop. is flashing. The milk froth is
being prepared.
■Turn the valve switch 11 anticlockwise
until it stops.
The preparation is finished.
■Rinse the Cappuccinatore after
each use.
Heating milk
■Switch on the device.
■Submerse the Cappuccinatore hose 13
directly into the milk.
■Press the button. flashes while
the appliance is heating up. After the
heat-up phase, is illuminated.
■Turn the control dial (Image F, 3) to the
"Warm milk" position ( is pointing up).
■Turn the valve switch 11 clockwise until
it stops. is flashing. The milk is being
heated.
■Turn the valve switch 11 anticlockwise
until it stops. The heating is completed.
■Rinse the Cappuccinatore after
each use.
Rinsing the Cappuccinatore
The Cappuccinatore should be cleaned
at regular intervals ("Cleaning the
Cappuccinatore", page 25).
It is recommended to rinse the
Cappuccinatore on a weekly basis with
the Melitta®PERFECT CLEAN milk
system cleaner. Use the milk cleaning
solution instead of clear water.
■Switch on the device.
■Fill a vessel halfway with clear water.
■Hold a vessel under the Cappuccinatore.
The hose of the Cappuccinatore must be
submersed in the water.
■Press the button for steam
dispensing.
■Turn the control dial (Image F, 3) to the
"Milk froth" position ( is pointing up).
■Turn the valve switch 11 clockwise until
it stops. Close the valve switch when
a mixture of clean water and steam
comes out.
■Wait for 30 seconds or press the
button to change to the normal operating
mode.
Dispensing hot water
A maximum of 150 ml of hot water can be
dispensed in each process. To dispense
a larger amount of hot water, repeat the
process.
■Switch on the device.
■Turn the control dial (Image F, 3) to the
"Hot water" position ( is pointing up).
■Hold a vessel under the Cappuccinatore.
■Turn the valve switch 11 clockwise until
the stop. is flashing. Hot water will
flow into the vessel.
■Turn the valve switch 11 anticlockwise
until it stops.

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08
24
Water hardness and filter
GB
Water hardness and filter
It is important to properly set the water
hardness so that the appliance displays
the need to be descaled when required
required. From the factory, it is set at
water hardness 4.
The water hardness category 1 is
automatically set after inserting the
Melitta®PRO AQUA filter cartridge.
Melitta®PRO AQUA Filter cartridge
The Melitta®PRO AQUA filter cartridge
filters lime scale and other contaminants
from the water. The water filter should be
changed every 2 months, however, at the
latest when appears on the display.
The water filter is available in specialised
shops.
Inserting the water filter
flashes during the entire change
procedure.
■Put the water filter in a glass with
tap water for several minutes before
inserting it in the appliance.
■Switch off the device.
■Press and hold the and buttons
for approx. 3 seconds, then release.
appears on the display.
■Empty the drip tray and insert without
the coffee grounds container.
illuminates.
■Pull the water tank 7up and out of the
appliance.
■Empty the water tank.
■Screw the water filter onto the thread at
the bottom of the water tank.
■Fill the water tank with fresh tap water
up to the max. mark.
■Insert the water tank into the appliance.
illuminates.
■Place the coffee grounds container
under Cappuccinatore 13.
■Turn the valve switch 11 clockwise
until it stops. flashes on the display.
Water will flow into the vessel.
■When is illuminated on the display,
turn the valve switch 11 anticlockwise
until it stops.
■The device is ready for operation.
and illuminate. The water
hardness is automatically set to
hardness level 1.
■Empty and insert the coffee grounds
container.
After inserting the water filter, the water
can be cloudy during the first rinse
because excess activated carbon is
washed out of the filter. The water will
then be clear again.
Setting the water hardness
The appliance includes a test strip to
determine the water hardness.
■Determine the hardness of the tap water
using the test strip.
■Switch on the device.
■Press the and buttons
simultaneously for longer than 2
seconds. flashes rapidly.
■Press the button to show the
menu for setting the water hardness.
illuminates.
■Set the determined water hardness by
pressing the button. The selected
water hardness is shown by the bean
symbols .

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08 25
Cleaning and maintenance
GB
Water hardness °dH °e °fH
1: 0 - 10 0 - 13 0 - 18
2: 10 - 15 13 - 19 18-27
3: 15 - 20 19 - 25 27-36
4: flashing >20 >25 >36
■Press to confirm the selection.
Cleaning and maintenance
WARNING
Electric shock hazard due to supply
voltage!
▶Pull the power supply plug before
cleaning.
▶Never immerse the appliance
in water.
▶Do not use a steam cleaner.
Daily cleaning
■Wipe the outside of the appliance with a
soft damp cloth and normal dishwashing
liquid.
■Empty the drip tray.
■Empty the coffee grounds container.
Cleaning the Cappuccinatore
■Let the Cappuccinatore cool down.
■Wipe the Cappuccinatore on the outside
with a damp cloth.
■Pull the Cappuccinatore 13 off of
the steam pipe 12.
■Remove the milk hose, the milk froth /
hot water nozzle (Image F,6) and the
air intake pipe (Image F,2) from the
connecting piece (Image F,5).
■Rinse all of the parts thoroughly
with water.
■Reassemble the Cappuccinatore in
the reverse order.
■Push the Cappuccinatore 13 onto
the steam pipe 12.
Cleaning the brewing unit
It is recommended to clean the brewing
unit once a week.
■Switch off the device.
■Pull off the cover 14 to the right.
■Press and hold the red button on the
handle of the brewing unit (Image B, 1).
■Turn the handle clockwise until it stops.
■Pull the brewing unit out of the appliance
by the handle.
■Rinse the brewing unit thoroughly on all
sides with clear water. The area shown
in Image D(arrow) must be free of
coffee residues.
■Let the brewing unit drip dry.
■Remove coffee residues from the
appliance.
■Insert the brewing unit back into the
appliance, press and hold the red
button (Image B, 1) and turn the handle
anticlockwise until it stops.
■Insert the cover until it clicks in.
Integrated cleaning programme
The integrated cleaning programme
(takes about 15 minutes) removes
residues and coffee oil residues that
cannot be removed by hand. The cleaning
symbol flashes during the entire
process.

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08
26
Cleaning and maintenance
GB
The cleaning programme should be
performed every 2 months or after 200
brewed cups, however, at the latest when
is illuminated.
■Before starting the cleaning program,
clean the brewing group and the interior
("Cleaning the brewing unit", page 25).
Only use Melitta®PERFECT CLEAN
cleaning tabs.
■Switch off the device.
■Fill the water tank with tap water up to
the max. mark.
■Insert the water tank.
■Press the and buttons
simultaneously for longer than
2 seconds. flashes, illuminates.
■Empty the drip tray and coffee grounds
container.
■Insert the drip tray without the coffee
grounds container
■Place the coffee grounds container
under outlet 2.
Cleaning phase 1 ( ):
Two rinsing processes will be executed.
When illuminates, proceed as follows:
■Remove the brewing unit.
■Put a cleaning tab in the brewing unit
(Image C).
■Insert the brewing unit.
Cleaning phase 2 ( ):
When illuminates, proceed as follows:
■Fill the water tank with tap water up to
the max. mark.
■Press the button to continue with
the cleaning programme (takes about 5
minutes).
Cleaning phase 3 ( ):
When illuminates, proceed as follows:
■Empty the drip tray and coffee grounds
container.
■Insert the drip tray without the coffee
grounds container
■Place the coffee grounds container
under outlet 2.
Cleaning phase 4 ( , the middle
bean is flashing):
■The cleaning programme will be
continued again and takes about
5 minutes.
When illuminates, proceed as follows:
■Empty the drip tray and coffee grounds
container and insert them in the
appliance as usual.
The cleaning programme is finished.
Integrated descaling programme
WARNING
The descaling agent can cause skin
irritations!
▶Comply with the safety instructions
and the dosing information specified
on the descaling agent packaging.
The integrated descaling programme
(takes about 30 minutes) removes lime
residues inside the appliance. The symbol
for descaling flashes during the entire
process.
The descaling programme should be
performed every 3 months, however,
at the latest when illuminates
("Setting the water hardness", page 24).
Only use Melitta®ANTI CALC.
■Switch off the device.
■Remove the water filter if necessary
("Water hardness and filter", page 24).
■Press the and buttons
simultaneously for approx. 3 seconds.
flashes, illuminates.

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08 27
Other settings
GB
Descaling phase 1 ( ):
■Empty and reinsert the drip tray.
■Place the coffee grounds container
under the Cappuccinatore.
■Turn the control dial (Image F, 3) to the
"Hot water" position ( is pointing up).
illuminates.
■Completely empty the water tank.
■Add the descaling agent to the water
tank according to the instructions on the
packaging.
■Insert the water tank.
■Press the button to start the
descaling programme (takes about
15 minutes).
Descaling phase 2 ( ):
When illuminates, proceed as follows:
■Ensure that the coffee grounds container
is placed under the Cappuccinatore.
■Turn the valve switch 11 clockwise until
the stop. is flashing. Water will flow
intermittently into the coffee grounds
container (takes about 10 minutes).
is then illuminated.
■Empty the drip tray and coffee grounds
container.
■Reinsert the drip tray and put the coffee
grounds container back under the
Cappuccinatore. illuminates.
■Remove the water tank and rinse
thoroughly with clear water.
■Fill the water tank with tap water up to
the max. mark.
■Insert the water tank.
■Press the button to continue with the
descaling programme. is flashing.
Water flows into the coffee grounds
container.
Descaling phase 3 ( ):
When illuminates, proceed as follows:
■Turn the valve switch 11 anticlockwise
until it stops.
Water flows inside the appliance into
the drip tray.
■When is illuminated, empty the drip
tray and the coffee grounds container
and reinsert them. When is
illuminated, the descaling programme
is finished.
■Insert the water filter if necessary
("Water hardness and filter", page 24).
Other settings
Energy-saving mode
After the last action, the appliance
switches automatically (depending on
the settings) to the energy-saving mode.
From the factory, the appliance is set at
5 minutes .
■Switch on the device.
■Press the and buttons
simultaneously until flashes.
■Press the button twice.
illuminates.
■Press the button until one of the four
times is set. The time is displayed by the
beans on display 9.
Display Time
5 minutes
(factory setting)
15 minutes
30 minutes
flashing off
■Press the button to confirm the
setting.

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08
28
Transport, Storage and Disposal
GB
Auto-OFF function
The appliance switches off automatically
after the last action (depending on the
setting). From the factory, the appliance is
set at 30 minutes .
■Switch on the device.
■Press the and buttons
simultaneously until flashes.
■Press the button three times.
illuminates.
■Press the button until one of the
four switch-off times is set. The time is
displayed by the beans on display 9.
Display Time
30 minutes
(factory setting)
2 hours
4 hours
flashing 8 hours
■Press the button to confirm the
setting.
Brewing temperature
From the factory, the brewing temperature
is set to Level 2 (medium ).
■Switch on the device.
■Press the and buttons
simultaneously until flashes.
■Press the button four times.
illuminates.
■Press the button, until one of the
three brewing temperatures is set.
The temperature is shown by the beans
on display 9 (from = low
to = high.).
■Press the button to confirm the
setting.
Adjusting the grinding fineness
The grinding fineness was set before the
appliance was delivered. We therefore
recommend to only adjust the grinding
fineness after about 1 000 coffee
preparations (about 1 year).
The grinding fineness should only be
adjusted immediately after starting coffee
dispensing and only while the mill is
running.
■Pull off the cover 14 to the right.
■Start dispensing coffee.
■Put the lever (Image E) in a desired
position (left = fine to right = coarse).
■Insert the cover and swivel to the left
until it clicks in.

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08 29
Transport, Storage and Disposal
GB
Transport, Storage and
Disposal
Venting
WARNING
There is a risk of burn injuries and
scalding due to hot steam and the
hot steam pipe!
The machine releases hot steam when
it is vented.
▶Never touch the steam pipe during
use or immediately after use.
The appliance should be vented when
it has not been used for a while or has
been transported. The appliance is then
protected from frost damage.
■Remove the water filter if necessary
("Water hardness and filter", page 24)
and keep it cool in a glass filled with tap
water.
■Switch on the device.
■Press the and buttons
simultaneously for approx. 2 seconds.
flashes, and then illuminates.
■Pull the water tank 7up and out of the
appliance. illuminates.
■Place a vessel under the
Cappuccinatore 13.
■Turn the valve switch 11 clockwise until
the stop. is flashing. Water flows out
of the steam pipe and into the vessel;
steam will also escape.
■When there is no more steam escaping:
Turn the valve switch 11 anticlockwise
until the stop.
■Insert the water tank into the appliance.
Transport
■Vent the appliance.
■Empty and clean the drip tray and coffee
grounds container.
■Empty the water tank and the bean
container. If necessary, vacuum out
beans that are stuck at the bottom.
■Pull the Cappuccinatore 13 off of the
steam pipe 12.
■"Cleaning the brewing unit", page 25.
■If possible, transport the appliance in
the original packaging including the hard
foam elements.
Disposal
This appliance is labelled according to
the European Directive 2002/96/EC on
waste electrical and electronic equipment
(WEEE). The Directive prescribes the
framework for a EU-wide applicable return
and recycling of waste appliances. Please
contact a specialised dealer for current
disposal procedures.

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08
30
Transport, Storage and Disposal
GB
Troubleshooting
Malfunction Cause Measure
Coffee only flows drop-by-
drop. Grinding fineness is too fine.
Adjust the grinding fineness more
coarse.
Clean the brewing unit.
Perform a descaling or cleaning
programme if necessary.
Coffee does not flow. Water tank not filled or
incorrectly inserted. Fill the water tank and make sure it is properly inserted.
The brewing unit is clogged. Clean the brewing unit.
The grinder is not grinding.
The beans are not falling
into the grinder. Tap lightly on the bean container.
Foreign objects in the
grinder. Call the hotline.
Loud grinder noise. Foreign objects in the
grinder. Call the hotline.
Bean symbols are
flashing although the bean
container is full.
Insufficient quantity of
ground beans in the
brewing chamber. Press the button or
button.
Appliance indicates "no
water" even though the water
tank is filled.
illuminates on the
display.
The float is blocked. Check the condition of the float in the water tank, remove the water
and carefully shake the tank.
The symbol is illuminated
without a reason. There is air in the lines
inside the appliance.
Turn the valve switch 11 clockwise
until the stop until water flows out of
the appliance.
Clean the brewing unit if necessary.
The cleaning or descaling
process was interrupted.
The power supply was
interrupted, e.g. due to a
power outage.
The appliance performs a rinsing
program autonomously. To do
so, follow the instructions on the
appliance.
Not enough milk froth is
formed during the frothing
process.
The control dial of the
Cappuccinatore is in the
wrong position. Adjust to the proper position.
The Cappuccinatore is dirty. Take the Cappuccinatore apart and
clean it.
The brewing unit can no
longer be reinserted after
removal.
The brewing unit is not
properly locked.
Check whether the handle for
locking the brewing unit is correctly
engaged.
The actuator is not in the
proper position.
Switch the appliance off and
then on again. Press the
and buttons simultaneously
for longer than 2 seconds. The
actuator is put into position. Then
reinsert the brewing unit and make
sure it is correctly locked into place.

Operating Instructions: Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08 31
Technical data
GB
Troubleshooting
Malfunction Cause Measure
The symbols for cleaning
and stand-by flash
alternately.
The brewing unit is missing
or not properly inserted. Insert the brewing unit properly and lock.
The brewing chamber is
overfilled.
Switch off the appliance and switch
it on again using the ON/OFF
button (repeat if necessary) until
standby mode is displayed.
Continuous flashing of all
buttons. System error
Switch off the appliance and switch
it on again via the ON/OFF button
; if this does not solve the
problem send the appliance to the
service department.
Technical data
Technical data
Operating voltage 220-240 V, 50/60 Hz
Power consumption maximum 1400 W
Pump pressure maximum 15 bar
Dimensions
Width
Depth
Height
200 mm
455 mm
325 mm
Capacity
Bean container
Water tank 125 g 1.2 l
Weight (empty) 8,1 kg
Ambient conditions
Temperature
Relative humidity 10°C to 32°C 30% to 80% (non-condensing)
You can reset the appliance to the default
settings.
Prerequisite: The appliance must be
ready for operation.
■To do so, press the on/off button and
also press the steam dispensing button
for more than 2 seconds.
→The appliance has been reset to
default settings.
Overview of default settings:
Default settings
Brewing temperature Medium
Water hardness Very hard
Timer for
Auto OFF function 30 minutes
Timer for energy-saving
mode 5 minutes
Reset the appliance to the default settings

Melitta Europa GmbH & Co. KG
Division Household Products
Ringstr. 99
D-32427 Minden
Germany
www.melitta.de
Melitta®Solo®& Perfect Milk|1830-0618 | 2018-08
1830-0618