Necta Kikko Max P250U00 Owner's manual

PRPR PRPR
PROGRAMMING MANUOGRAMMING MANU
OGRAMMING MANUOGRAMMING MANU
OGRAMMING MANUALAL
ALAL
AL
Kikko Max
Code: P250U00
English
11 - 2005Date:

P250U00 11-2005
Legend
Necta’s vending machines can function in 3 different operating modes:
- Normal vending mode- Normal vending mode
- Normal vending mode- Normal vending mode
- Normal vending mode
- Filler menu- Filler menu
- Filler menu- Filler menu
- Filler menu
- Technician menu- Technician menu
- Technician menu- Technician menu
- Technician menu
In order to access the programming menus, press the programming button located on the inside of the door (1):
At this point the machine goes into Filler menu mode.
The buttons shown in the figure are used for surfing through the different menus:
Scrolling buttons UP ( ) and DOWN ( )
The UP and DOWN scrolling buttons are used for moving from one programming menu item to the next one, located in
the same level, and at the same time change the status or the numeric value of the corresponding functions.
Confirm / enter button ( )
The confirm / enter button is used for moving to the lower level or for confirming a value after being entered or changed.
Exit button ( )
The exit button is used for returning to the higher level or for exiting a change field of a function. When reaching the
highest level in the menu, this button is pressed for going from the Technician menu into the Filler menu and vice versa.

P250U00 11-2005Filler Menu
1 STATISTICS 1 Statistics
1.1 Printing the Statistics
1.1.1 Partial printout
1.1.1.1 Printing the selection counters
When confirming this function, the counters regarding the
different selections are printed.
1.1.1.2 Printing the time band counters
When confirming this function, the counters regarding the
different time bands are printed.
1.1.1.3 Printing the discount counters
When confirming this function, the counters regarding dis-
counts and overprice are printed.
1.1.1.4 Printing the failure counters
When confirming this function, the counters regarding the
different failure are printed.
1.1.1.5 Printing the coin mechanism data
When confirming this function, the counters regarding the
coin mechanism data are printed.
1.1.2 Total printout
When confirming this function, all statistics are printed.
1.2 Printing the relative statistics
1.2.1 Partial printout
1.2.1.1 Printing the selection counters
When confirming this function, the relative counters regarding
the different selections are printed.
1.2.1.2 Printing the time band counters
When confirming this function, the relative counters regarding
the different time bands are printed.
1.2.1.3 Printing the discount counters
When confirming this function, the relative counters regarding
discounts and overprice are printed.
1.2.1.4 Printing the failure counters
When confirming this function, the relative counters regarding
failures are printed.
1.2.1.5 Printing the coin mechanism data
When confirming this function, the relative counters regarding
the coin mechanism data are printed.
1.2.2 Total printout
When confirming this function, all relative statistics are
printed.
1.1 STATISTICS PRINTING
1.1.1 Partial printing
1.1.1.1 SELECT.COUNT. PRINT.
1.1.1.2 PRINT BAND COUNTER
1.1.1.3 DISCOUNT COUNT.PRIN.
1.1.1.4 FAILURE COUNT.PRINT.
1.1.1.5 COIN MECH.DATA PRINT
1.1.2 TOTAL PRINTING
1.2 PRINT RELAT. STAT.
1.2.1.1 SELECT.COUNT. PRINT.
1.2.1.2 PRINT BAND COUNTER
1.2.1.3 DISCOUNT COUNT.PRIN.
1.2.1.4 FAILURE COUNT.PRINT.
1.2.1.5 COIN MECH.DATA PRINT
1.2.1 Partial printing
1.2.2 TOTAL PRINTING

P250U00 11-2005Filler Menu
1.3 STATISTICS DISPLAY
1.3.1 SELECT. COUNT. DISP.
1.3.1.1 COUNT DISP. X S.SEL.
1.3.1.2 TOTAL COUNT DISPLAY
1.3.1.3 SEL.NO.COUNT. DISPL.
1.3.2 DISPLAY BAND COUNTER
1.3.3 DISCOUNT COUNT.DISP.
1.3.4 FAILURE COUNT. DISP.
1 STATISTICS
1.3 Displaying the statistics
1.3.1 Displaying the selection counters
1.3.1.1 Displaying the single counters
This function is used for displaying the counters regarding
each selection, divided by price band (0, 1, 2, 3, 4, Free, Test).
1.3.1.2 Displaying the total counters
This function is used for displaying the total counters regard-
ing each selection.
1.3.1.3 Displaying the selection counters in
normal/maintenance mode
This function is used for displaying the total counters regard-
ing the selections made while in normal mode and mainte-
nance mode.
1.3.2 Displaying the time band counters
When selecting the desired price band (0, 1, 2, 3, 4, Free, Test),
the total number of selections made for that price band is
displayed.
1.3.3 Displaying the discount counters
This function is used for displaying the total amount of
discounts and overprice accumulated for the dispensed
selections.
1.3.4 Displaying the failure counters
This function is used for displaying the number of times each
possible failure occurred in the vending machine.
1.3.5 Displaying the coin mechanism data
1.3.5.1 Displaying the audit data
This function is used for displaying the number of coins
inserted in the vending machine, differentiated by the type of
coin.
1.3.5.2 Displaying the cashed amount
This function is used for displaying the value of:
- Total cashed
- Total sold
- Total cashed by credit
1.3.5 COIN MECH.DATA DISP.
1.3.5.1 AUDIT DATA DISPLAY
1.3.5.2 CASH COUNT. DISPLAY

P250U00 11-2005Filler Menu
1 STATISTICS
1.4 Displaying the relative statistics
1.4.1 Displaying the selection counters
1.4.1.1 Displaying the single counters
This function is used for displaying the counters regarding
each selection, divided by price band (0, 1, 2, 3, 4, Free, Test).
1.4.1.2 Displaying the total counters
This function is used for displaying the total counters regard-
ing each selection.
1.4.1.3 Displaying the selection counters in
normal/maintenance mode
This function is used for displaying the total counters regard-
ing the selections made while in normal mode and mainte-
nance mode.
1.4.2 Displaying the time band counters
When selecting the desired price band (0, 1, 2, 3, 4, Free, Test),
the total number of selections made for that price band is
displayed.
1.4.3 Displaying the discount counters
This function is used for displaying the total amount of
discounts and overprice accumulated for the dispensed
selections.
1.4.4 Displaying the failure counters
This function is used for displaying the number of times each
possible failure occurred in the vending machine.
1.4.5 Displaying the coin mechanism data
1.4.5.1 Displaying the audit data
This function is used for displaying the number of coins
inserted in the vending machine, differentiated by the type of
coin.
1.4.5.2 Displaying the cashed amount
This function is used for displaying the value of:
- Total cashed
- Total sold
- Total cashed by credit
1.4 DISPLAY RELAT. STAT.
1.4.1 SELECT. COUNT. DISP.
1.4.1.1 COUNT DISP. X S.SEL.
1.4.1.2 TOTAL COUNT DISPLAY
1.4.1.3 SEL.NO.COUNT. DISPL.
1.4.4 FAILURE COUNT. DISP.
1.4.5 COIN MECH.DATA DISP.
1.4.5.1 AUDIT DATA DISPLAY
1.4.5.2 CASH COUNT. DISPLAY
1.4.2 DISPLAY BAND COUNTER
1.4.3 DISCOUNT COUNT.DISP.

P250U00 11-2005Filler Menu
1 STATISTICS
1.5 Deleting the relative statistics
1.5.1 Partial delete
1.5.1.1 Deleting the selection counters
When confirming this function, the counters regarding the
different selections, described at point 3.4.1, are deleted.
1.5.1.2 Deleting the discount counters
When confirming this function, the counters regarding dis-
counts and overprice, described at point 3.4.2, are deleted.
1.5.1.3 Deleting the failure counters
When confirming this function, the counters regarding the
different failures, described at point 3.4.3, are deleted.
1.5.1.4 Deleting the coin mechanism data
When confirming this function, the counters regarding the
coin mechanism data, described at point 3.4.4, are deleted.
1.5.2 Total delete
When confirming this function, all relative statistics are
deleted.
1.5 DELETE RELAT. STAT.
1.5.2 TOTAL RESET
1.5.1 PARTIAL RESET
1.5.1.1 SELECT. COUNT. RESET
1.5.1.2 DISCOUNT COUNT.RESET
1.5.1.3 FAILURE COUNT. RESET
1.5.1.4 COIN MECH DATA RESET

P250U00 11-2005Filler Menu
2 Setting single prices
Four different prices can be set for each selection according to
the programmed time bands, if enabled.
2.1 Price band 0
This function is used for setting the prices of each selection for
time band 0 (if enabled).
2.1 Price band 1
This function is used for setting the prices of each selection for
time band 1 (if enabled).
2.1 Price band 2
This function is used for setting the prices of each selection for
time band 2 (if enabled).
2.1 Price band 3
This function is used for setting the prices of each selection for
time band 3 (if enabled).
2.1 Price band 4
This function is used for setting the prices of each selection for
time band 4 (if enabled).
3 Change tubes control
3.1 Filling the change tubes
From this function, the change tubes can be filled manually.
Confirm refilling, and the display will indicate
“Credit: ——” which is the value of money available in change
the tubes; insert the desired coin into the validator and the
display will indicate the value of money available in the change
tubes.
3.2 Releasing the change tubes
From this function, the change tubes can be released manually.
When confirming releasing, it will be possible to decide which
tube to release. Each time the confirm button is pressed, a coin
is ejected from the active tube.
4 Boiler temperature
This function is used for setting the operating temperature of
the boiler, expressed in °C.
3 TUBE CONTROL
3.1 FILLING TUBE
3.2 TUBE EMPTYING
4 BOILER TEMPERAT.
2.1 PRICE BAND 0
2.1 PRICE BAND 4
2.1 PRICE BAND 3
2.1 PRICE BAND 2
2.1 PRICE BAND 1
2 SET INDIVIDUAL PRICE

P250U00 11-2005Filler Menu
5 Test 5 Test
5.1 Complete dispensing
With this function it is possible to obtain, with the door open
and without inserting any money, complete dispensing for each
selection.
5.2 Dispensing water only
With this function it is possible to dispense, with the door
open and without inserting any money, only the water doses
for each selection.
5.3 Dispensing powder only
With this function it is possible to dispense, with the door
open and without inserting any money, only the powder doses
for each selection.
5.4 Dispensing without accessories
With this function it is possible to dispense, with the door
open and without inserting any money, only the water and
powder doses for each selection, without any cup and stirrer.
5.5 Dispensing accessories only
With this function it is possible to dispense, with the door
open and without inserting any money, only the accessories for
each selection.
6 GSM
6.1 Resetting the pre-alarm counters
With this function the counters that control the pre-alarms
are reset.
7 EVADTS
7.1 Connection
This function places the machine in wait mode for connection
to retrieve data.
5.1 COMPLETE DISPENSING
5.2 WATER ONLY
5.3 POWDER ONLY
5.4 WITHOUT ACCESSORIES
5.5 ACCESSORIES ONLY
6 gsm
7 evadts
7.1 CONNECTION
6.1 RESET PRE-ALARM CNT.

P250U00 11-2005Technician Menu
1. FAILURES
1.1 FAILURE READING
1. Failures
1.1 Reading the failures
When the “Failure” function is displayed, press the confirm but-
ton “ ” to display the present failures.
If no failures are currently present, after pressing the confirm
button “ ” the message “End failures” will be displayed.
The possible failures are indicated in the following cases:
Water failureWater failure
Water failureWater failure
Water failure
If the air-break micro-switch is closed for more than one minute,
the water inlet solenoid valve will remain energized until the
water flow is restored.
Waste container fullWaste container full
Waste container fullWaste container full
Waste container full
This occurs after the liquid waste container float is triggered.
Air-breakAir-break
Air-breakAir-break
Air-break
The machine is locked if after 7 selections the micro-switch has
never signalled the lack of water.
No cups in the dispenserNo cups in the dispenser
No cups in the dispenserNo cups in the dispenser
No cups in the dispenser
When the empty cup stack micro-switch opens, the stack shift
motor is activated. If after one full turn of the cup dispenser the
micro-switch is not closed the machine locks.
Mobile spoutsMobile spouts
Mobile spoutsMobile spouts
Mobile spouts
If the spouts do not reach the dispensing position, the machine
is disabled.
ImpellerImpeller
ImpellerImpeller
Impeller
Failed computation of the volumetric counter within a maxi-
mum given time.
BoilerBoiler
BoilerBoiler
Boiler
The machine will lock if after 10 minutes of heating from the
machine start, or from the last selection, the boiler fails to reach
the operating temperature.
Machine control boardMachine control board
Machine control boardMachine control board
Machine control board
Failed dialogue between C.P.U. board and machine control board.
Coin mechanismCoin mechanism
Coin mechanismCoin mechanism
Coin mechanism
The machine is locked if it receives a pulse longer than 2 sec-
onds on a validator line or the communication with the serial
coin mechanism does not take place for more than 30 seconds
(Executive protocol) or 75 seconds (BDV protocol).
Coffee releaseCoffee release
Coffee releaseCoffee release
Coffee release
If after releasing the ground coffee dose the micro-switch of the
coffee doser unit indicates the presence of coffee in the dosing
chamber, all coffee-based selections are disabled.
Coffee unitCoffee unit
Coffee unitCoffee unit
Coffee unit
Due to mechanical blocking of the unit. The machine is not locked,
but all tea-based selections are disabled.
No coffeeNo coffee
No coffeeNo coffee
No coffee
If after a period of 15 seconds of grinding coffee a dose is not
obtained, all coffee-based selections are disabled.
Water failure
Waste container full
air-break
No cups
spouts
Volumetric counter
Boiler
Machine board
Coin mechanism
Coffee release
Coffee unit
No coffee

P250U00 11-2005Technician Menu
RAM DataRAM Data
RAM DataRAM Data
RAM Data
One or more areas of the RAM contain wrong data which was
corrected with the default values.
The machine will continue to function, but it would be advisable
to initialise as soon as possible.
Cup releaseCup release
Cup releaseCup release
Cup release
If the cup sensor photocell is fitted, after three unsuccessful at-
tempts at releasing cups the display will indicate the message
“No cups”. Using a special function, it is possible to define whether
this failure must lock the machine or leave it available for dis-
pensing into a ceramic cup.
1.2 Resetting the failures
By confirming this function all current failures will be reset
1.3 Fluorescent lamps switched off
Setting whether or not the lighting lamps in the external panels
are to be switched on when the machine is out of service or
during the “Energy saving” time band.
1. FAILURES
1.2 FAILURE RESET
RAM data
Cup release
1.3 V.M.NEON OUT OF SERV

P250U00 11-2005Technician Menu
2. SET PARAMETERS
2.1 cash
2.1.1 PRICES
2.1.1.2 SET GLOBAL PRICES
2.1.1.3 TIME SCHEDULE
2 Setting the parameters
2.1 Cash
This set of functions controls all parameters regarding the pay-
ment systems and the sales prices.
2.1.1 Prices
Four different prices can be set for each selection according to
the programmed time bands for when the time table option is
enabled.
For each of the 4 time bands prices (0 to 65,535) can be pro-
grammed globally (same price for all selections) or for the single
selections.
Should the majority of products be sold at the same price, it will
be convenient to set the price globally and then change the
figure of the selections with different prices.
2.1.1.1 Setting single prices
This function is used for setting a different price for each selec-
tion.
2.1.1.2 Setting global prices
This function is used for setting one price for all available selec-
tions.
2.1.1.3 Time bands
Four programmable time bands are provided for selling prod-
ucts at different prices.
The time periods are programmable for beginning and end time
by hours (00 to 23) and minutes (00 to 59).
If the values for start and end of the time band are set to 00.00
the time period is disabled.
The reference time is kept by an internal clock, programmable
as:
day/month/year week-day 1-7 and then hour/minutes/seconds.
If the values for start and end of the time band are set to 00.00
the time period is disabled.
2.1.1.1 SET INDIVIDUAL PRICE

P250U00 11-2005Technician Menu
2. SET PARAMETERS
2.1.2 COIN MECHANISM
executive
Validators
BDV
2.1.2 Coin mechanisms
2.1.2.1 Setting the coin mechanisms
It is possible to decide which of the payment system protocols
available are to be enabled for the functions.
The available payment systems are:
- Executive
- Validators
- BDV
- MDB
By selecting one of the systems it is possible to control its func-
tions.
ExecutiveExecutive
ExecutiveExecutive
Executive
The following payments systems are available for the Executive
system:
- Standard
- Price Holding
- Coges
- U-Key
- Sida
ValidatorsValidators
ValidatorsValidators
Validators
When the “Validat.Lines” (line setting) function of the “Techni-
cian” menu is displayed, the value of the 6 validator coin lines
can be changed.
BDVBDV
BDVBDV
BDV
The BDV protocol menus are used for defining the following
functions:
Type of vendingType of vending
Type of vendingType of vending
Type of vending
Setting the operating mode for multiple or single dispensing. With
multiple dispensing, the change is not automatically returned
after a successful selection; however the credit is available for
further selections. When pressing the coin return button, the
available credit is returned if its value is lower than the maxi-
mum change value.
Credit controlCredit control
Credit controlCredit control
Credit control
This function enables/disables the return of credit if no selec-
tions are made.
If enabled, this function allows the return of coins even if the first
selection was not dispensed.
If however a selection fails for any reason, the change will be
returned if requested.
Maximum creditMaximum credit
Maximum creditMaximum credit
Maximum credit
This function is used to define the maximum accepted credit.
Maximum changeMaximum change
Maximum changeMaximum change
Maximum change
It is possible to set a limit to the total amount of change returned
by the coin mechanism when pressing the coin return button or
after a single dispensing serving.
Any credit exceeding the amount programmed with this func-
tion will be cashed.
2.1.2.1 COIN MECHANISM SET.

P250U00 11-2005Technician Menu
2. SET PARAMETERS
BDV
Accepted coinsAccepted coins
Accepted coinsAccepted coins
Accepted coins
It is possible to define which, among the coins recognised by the
validator, are to be accepted.
Check the label on the coin mechanism for the correct coin to
value matching, indicating the position of the coins.
Non accepted coinsNon accepted coins
Non accepted coinsNon accepted coins
Non accepted coins
This function programs the rejection of coins when in “exact
amount” mode.
Check the label on the coin mechanism for the correct coin to
value matching, indicating the position of the coins.
Dispensing buttonsDispensing buttons
Dispensing buttonsDispensing buttons
Dispensing buttons
This function enables or not the buttons on the coin mechanism
used to release the coins in the change return tubes.
Value of “exact amount”Value of “exact amount”
Value of “exact amount”Value of “exact amount”
Value of “exact amount”
This value defines the combination of empty coin tubes, setting
the coin mechanism in “exact amount” mode. The possible com-
binations of empty coin tubes are indicated below.
For greater simplicity, the combination is described with refer-
ence to tubes A, B and C, where tube A receives the lower value
coins and tube C the greater value coins.
0 = A or (B and C)
1 = A and B and C
2 = A and B only
3 = A and (B or C)
4 = A only
5 = A or B (default) only
6 = A or B or C
7 = A or B only
8 = A or C only
9 = B and C only
10 = B only
11 = B or C only
12 = C only
C.P.C. deviceC.P.C. device
C.P.C. deviceC.P.C. device
C.P.C. device
It dialogues with the coin mechanism if devices are installed or
removed from the serial interface (C.P.C.-type devices - the moni-
toring unit is always enabled by default).
Minimum level of tubesMinimum level of tubes
Minimum level of tubesMinimum level of tubes
Minimum level of tubes
It brings forward the “Insert exact amount” message for the user,
by adding a number of coins between 0 and 15 to the pro-
grammed number of coins, to set the “full change tubes” status.
Free Vend VMCFree Vend VMC
Free Vend VMCFree Vend VMC
Free Vend VMC
Most payment systems with the BDV protocol control the free
vend function.
However, there are some payment systems without such func-
tion.
In this case, if free selections are to be dispensed, free vending
must be enabled with VMC (vending machine control, enabled
by default) and the price of the selections must be set to zero.
2.1.2.1 COIN MECHANISM SET.

P250U00 11-2005Technician Menu
2. SET PARAMETERS
MDB MDBMDB
MDBMDB
MDB
The MDB protocol menus are used for defining the following
functions:
Type of vendingType of vending
Type of vendingType of vending
Type of vending
Setting the operating mode for multiple or single dispensing. With
multiple dispensing, the change is not automatically returned
after a successful selection; however the credit is available for
further selections. When pressing the coin return button (if the
function is enabled), the available credit is returned up to the
maximum change value.
Credit controlCredit control
Credit controlCredit control
Credit control
To enable/disable the operation of the coin return button.
Maximum creditMaximum credit
Maximum creditMaximum credit
Maximum credit
This function is used to define the maximum accepted credit.
Maximum changeMaximum change
Maximum changeMaximum change
Maximum change
It is possible to set a limit to the total amount of change returned
by the coin mechanism when pressing the coin return button or
after a single dispensing serving.
Any credit exceeding the amount programmed with this func-
tion will be cashed.
Accepted coinsAccepted coins
Accepted coinsAccepted coins
Accepted coins
It is possible to define which, among the coins recognised by the
validator, are to be accepted when the change tubes are full.
Check the coin mechanism configuration for the correct coin to
value matching.
Returned coinsReturned coins
Returned coinsReturned coins
Returned coins
It is possible to define which, among the coins available in the
tubes, are to be used for returning the change. This parameter is
active only with coin mechanisms that do not automatically con-
trol the choice of tube to be used (Auto changer payout).
Check the coin mechanism configuration for the correct coin to
value matching.
Accepted billsAccepted bills
Accepted billsAccepted bills
Accepted bills
It is possible to define which, among the bills recognised by the
reader, are to be accepted.
Check the reader configuration for the correct bill to value match-
ing.
Minimum level of tubesMinimum level of tubes
Minimum level of tubesMinimum level of tubes
Minimum level of tubes
This function is used for setting the number of coins (0 to 15)
to determine the status of full change tubes and the “Insert
exact amount” message for the user.
2.1.2.1 COIN MECHANISM SET.

P250U00 11-2005Technician Menu
2. SET PARAMETERS
2.1.2.2 IMMEDIATE CHANGE
2.1.3 DECIMAL POINT
Accepted coins with “exact amount”Accepted coins with “exact amount”
Accepted coins with “exact amount”Accepted coins with “exact amount”
Accepted coins with “exact amount”
It is possible to define which, among the coins recognised by the
validator, are to be accepted when the machine is in the “exact
amount” condition.
Check the coin mechanism configuration for the correct coin to
value matching.
Accepted bills with “exact amount”Accepted bills with “exact amount”
Accepted bills with “exact amount”Accepted bills with “exact amount”
Accepted bills with “exact amount”
It is possible to define which, among the bills recognised by the
accepter, are to be accepted when the machine is in the “exact
amount” condition.
Check the accepter’s configuration for the correct bill to value
matching.
2.1.2.2 Immediate change
Normally, the amount of a selection is cashed after the machine
sends the message “Selection successful”.
When this function is enabled, disabled by default, the cash mes-
sage is sent at the beginning of dispensing.
2.1.3 Decimal point.
Press the confirm button “ ” to display the position of the deci-
mal point, i.e.:
0 decimal point disabled
1 XXX.X
2 XX.XX
3 X.XXX
Press the confirm button “ ”, these values will start blinking and
can then be modified as necessary.

P250U00 11-2005Technician Menu
2. SET PARAMETERS
2.1.4.3 VIRT.PRIC.RETURN
2.1.4.2 slave price hold
2.1.4 Master slave
2.1.4.1 SETTING
2.1.4 Master / Slave
2.1.4.1 Settings
The machine control system is pre-arranged for the connection
in a bank of vending machines using special kits.
This permits the use of a single payment system for more ma-
chines.
In the event of installation in a bank of machines, it can be
configured a “Master”, i.e. having control over the second ma-
chine, or as “Slave”, i.e. leaving the control to the other machine.
To be able to use this function there must be a numeric keypad
within the bank of machines.
There is the option of installing a numeric keypad in the ma-
chine for managing the slave machines without keypad and dis-
play.
After any changes it will be necessary to switch off the machine
and switch it on again.
The master/slave function is not enabled by default.
2.1.4.2 Slave Price Holding
To enable the function, it is necessary to define which machine is
master and which one is slave in the software of the master
machine and of the slave machine.
If an Executive payment system in “Price Holding” mode is
set in the master machine, the information must be set also in
the software of the slave machine.
The payment system of the slave machine must always be de-
fined as “Validator”.
In the event of failed electrical connection, both machines will
display the message “Failed communication”.
2.1.4.3 Return of virtual price
A combined selection is intended as the association of two se-
lections, one from the Kikko and one from the Snakky, to the
same number (80 to 89) sold at a single price.
Since a numeric keypad is required for setting and controlling
the combined selections, the relevant menu is included only
in the software of the Snakky.
Combined selections can be used either with the Snakky as mas-
ter and Kikko as slave (recommended configuration) or vice versa.
If one of the two selections is not available, the combined selec-
tion is not dispensed. If the immediate change option is not acti-
vated on the master machine, it might be possible that the first
selection fails. In this case the entire amount is returned. If the
second selection fails, it will be possible to decide whether to
keep or return the entire amount by activating/deactivating the
“Virtual price return” option.

P250U00 11-2005Technician Menu
2.1.4.4 reset snakky sl
2.1.4.5 monitor slave
2. SET PARAMETERS
2.1.4.4 Reset Snakky SL
This function is used for resetting the programming of a Snakky
SL to default values.
2.1.4.5 Monitor Slave
This function is used for scrolling through all the information of
a slave being connected.
When switching on the slave with the display showing this func-
tion, the display will indicate in a sequence all information on the
slave regarding:
- software version
- type of slave (XX, 0XX, 9XX)
- presence of dispensing detection photocells
- number of trays and compartments
- presence of dispensing compartment lock device
- internal sensor temperature.
To exit the function it will be necessary to switch the master
machine off.

P250U00 11-2005Technician Menu
2. SET PARAMETERS
2.2 SELECTIONS
2.2.1 SET WATER
2.2.1.1 WATER DOSES
2.2.1.2 set whipper
2.2.1.2.1 SET WHIP DOSES
2.2.1.2.2 SET MODALITY
2.2.1.4 SET DRIPPING
2.2 Selections
2.2.1 Setting the water
2.2.1.1 Water doses
This function is used for setting the water dose, expressed in cc,
for each selection button and therefore for each product as-
signed to it; the display indicates the name of the product being
selected.
2.2.1.2 Setting the whipper
2.2.1.2.1 Setting the whipper doses
The whipping time can be set for each selection button, for each
water dose that composes such selection.
The duration can be set in two different modes:
2.2.1.2.2 Setting the whipper mode
It is possible to choose between two different modes:
AbsoluteAbsolute
AbsoluteAbsolute
Absolute
i.e. independent from the solenoid valve opening time. The whip-
ping duration is set as tenths of a second for Instant models and
as volumetric counter pulses for Espresso models.
RelativeRelative
RelativeRelative
Relative
i.e. based on the difference, plus or minus, from the moment the
solenoid valve closes.
The whipping duration is always expressed in tenths of a sec-
ond.
2.2.1.3 Solenoid valve settings
It is possible to set the water flow rate of the single solenoid
valves expressed in cc/s (the default value setting in cc/s is indi-
cated in the selection dose table) to calculate the amount of
water to be dispensed.
2.2.1.4 Dripping time
The wait time (programmable from 0 to 3000 hundredths of a
second) from end of dispensing to the mobile spout return can
be set for each selection in order to leave time to the tubes to
drain.
2.2.1.3 ELECTROVALVE SETTING

P250U00 11-2005Technician Menu
2.2.2 SET POWDER
2. SET PARAMETERS
2.2.2.1 POWDER DOSES
2.2.2.2 DOSER SETTING
2.2.3.1 ENABLE CUP
2.2.3.3 ENABLE STIRRER
2.2.3.2 ENABLE SUGAR
2.2.4 SELECTION STATUS
2.2.6 SEL. ARRANGEMENT
2.2.7 SET PROD. CODE
2.2.2 Setting the powders
2.2.2.1 Powder doses
The powder dose, expressed in grams, can be set for each selec-
tion button and therefore each product assigned to it; the dis-
play indicates the name of the product being selected.
2.2.2.2 Setting the doser units
This function is used for setting the flow rate of the single
doser units, expressed in g/s, to calculate the amount of
powder to be dispensed, for correct conversion of product
dose values.
2.2.3 Setting the accessories
2.2.3.1 Enabling the cup
This function is used for enabling or disabling cup dispensing for
each selection button.
2.2.3.2 Enabling the sugar
This function is used for enabling or disabling sugar dispensing
for each selection button.
2.2.3.3 Enabling the stirrer
This function is used for enabling or disabling stirrer dispensing
for each selection button.
2.2.4 Selection status
Each single selection button can either be enabled or disabled.
2.2.5 Button <—> Selection
This function permits the association of a selection number, indi-
cated in the selection dose table, to a button in the direct selec-
tion keypad.
2.2.6 Selection position
This function is used for verifying to which selection the
button that has just been pressed is assigned.
2.2.7 Product code
This function is used for assigning a 4-digit code to each selec-
tion for processing the statistics.
2.2.3 SET ACCESSORIES
2.2.5 SELECTION <-> BUTTON

P250U00 11-2005Technician Menu
2. SET PARAMETERS
2.3 MACHINE PARAM.
2.3.1 BOILER TEMPERAT.
2.3.2 TANK
2.3.3 MIXER HEATING
2.3.5 FAST CYCLES
2.3.6 MAINT.DISPENS.SETT.
2.3.4 MIXER COOLING
2.3 Machine parameters
2.3.1 Boiler temperature
This function is used for setting the operating temperature, ex-
pressed in °C, of the boiler installed in the machine.
When pressing the confirm button “ ” the temperature value
starts blinking and can be modified.
2.3.2 Tank
The machine water supply can be from the mains or from an
internal tank. For some applications it is also possible to used
two internal tanks at the same time.
With this function it is possible to define whether the machine
water supply is from the mains (tank = 0) or from the tanks (tank
= 1 or 2).
2.3.3 Mixer heating
If the function is enabled and no selections were made
in the last 3 minutes, a small amount of hot water is dispensed
into the milk or instant coffee mixers before dispensing short
instant coffee, instant coffee with milk and espresso coffee with
milk.
2.3.4 Mixer cooling
If the function is enabled and no cold drink selections were made
in the last 5 minutes, a small amount of cold water is dispensed
into the cold drink mixers before dispensing the product.
2.3.5 Fast cycles
When this function is enabled, some of the time that is useful for
improving the drink quality is eliminated. all products that com-
pose the drink are dispensed at the same time, eliminating the
“post-whipping” time.
2.3.6 Setting dispensing in maintenance mode
After a programmable number of dispensed drinks, it is possible
to display the message “Regenerate the water softener” upon
accessing “Filler menu” mode.
2.3.7 Photocell
The machine is fitted with a “cup sensor” composed of a photo-
cell that detects the presence of an object in the dispensing
compartment.
When the function is enabled, if an object is detected in the
dispensing compartment, a cup is not released and the display
indicates the message “Without cup”.
It is also possible to define whether, after two attempts to release
a cup without the photocell detecting any objects in the dis-
pensing compartment; the failure should lock the machine or
leave it to operate using a ceramic cup.
A lighting lamp inside the dispensing compartment is controlled
by the cup sensor.
If the cup is still inserted, when the next selection is made the
message “Remove cup” is displayed.
2.3.7 PHOTOCELL