Members Mark GAS9670ASO User manual

Natural Gas Conversion
Instructions for Model
GAS9670AS / GAS9670ASO
Natural Gas Conversion Kit Sold Separately
PROFESSIONAL INSTALLATION MANUAL
ASSEMBLY AND OPERATING INSTRUCTIONS
NOTICE TO
PROFESSIONAL INSTALLER:
LEAVE THESE INSTRUCTIONS WITH THE
GRILL OWNER FOR FUTURE REFERENCE.
HAZARDOUS EXPLOSION MAY RESULT IF THESE
WARNINGS AND INSTRUCTIONS ARE IGNORED. READ
AND FOLLOW ALL WARNINGS AND INSTRUCTIONS IN
THIS MANUAL TO AVOID PERSONAL INJURY, INCLUDING
DEATH OR PROPERTY DAMAGE.
WARNING
SAVE THIS MANUAL FOR FUTURE REFERENCE

1
WE WANT YOU TO USE YOUR CONVERSION KIT FOR YOUR GRILL AS SAFELY AS POSSIBLE.
THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO ATTRACT THE ATTENTION TO
POSSIBLE HAZARDS AS THE GRILL IS CONVERTED AND USED AS A NATURAL GAS GRILL.
WHEN YOU SEE THE SAFETY ALERT SYMBOL
PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS!
READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY
BEFORE CONVERTING AND OPERATING YOUR GRILL.
DANGER
IMPORTANT SAFETY WARNINGS
1. Do not store or use gasoline or other ammable liquids or vapors in the vicinity of this or any other appliance.
2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
WARNING
Installer Company or Service Name: _______________________________________________
Technician Name:____________________________________Installation Date:_____________
Failure to follow the instructions as written, or installation by other than
a trained professional, will void all manufacturer warranties.
WARNING
This conversion kit shall be installed by a qualified service agency in accordance
with the manufacturer’s instructions and all applicable codes and requirements of the
authority having jurisdiction. If the information in these instructions is not followed
exactly, a fire, explosion or production of carbon monoxide may result causing property
damage, personal injury or loss of life. The qualified service agency is responsible
for the proper installation of this kit. The installation is not proper and complete until
the operation of the converted appliance is checked as specified in the manufacturer’s
instructions supplied with the kit.
Model Number: ____________________________________
Serial Number:_____________________________________Date Purchased: ____________
IMPORTANT: FILL OUT PRODUCT RECORD INFORMATION BELOW.
IF YOU SMELL GAS:
1. SHUT OFF GAS TO THE APPLIANCE.
2. EXTINGUISH ANY OPEN FLAME.
3. OPEN LID.
4. IF ODOR CONTINUES, KEEP AWAY FROM APPLIANCE AND IMMEDIATELY CALL YOUR GAS SUPPLIER OR
YOUR FIRE DEPARTMENT.

2
General Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Connecting to Natural Gas Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Leak Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Pre-start Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Lighting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
TABLE OF CONTENTS
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result
in death or serious injury.
WARNING: Be alert to the possibility of serious bodily injury if the instructions are not
followed. Be sure to read and carefully follow all of the messages.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderate injury.
INSTALLATION INFORMATION:
The installation of this appliance must be in accordance with:
All applicable local codes, or in the absence of local codes, either:
• National Fuel Gas Code ANSI Z223.1 NFPA 54
• Natural Gas and Propane Installation Code: CAN/CGA B149.1
• Natural Gas Installation Code: CAN/CGA B149.1 (Canada)
This kit converts your grill for natural gas use at 7 inch water column supply pressure. To check your pressure
contact your local natural gas company. If the supply pressure is different than 7 inch, contact a
professional
service technician
for assistance. Not for use with LP gas.
WARNING
• FOR OUTDOOR USE ONLY. DO NOT operate indoors or in an enclosed area such as a garage, shed
or breezeway.
• Use your grill OUTDOORS in a well ventilated space away from dwellings or other buildings to
prevent dangers associated with gas accumulation and toxic vapors. We recommend your grill be
situated at least 10 feet (3.1 m) from buildings.
• Maintain a minimum clearance of 36 inches (91 cm) between all sides of grill and walls or other
combustible material. DO NOT use grill under overhead unprotected combustible construction.
• DO NOT use or install this grill in or on a recreational vehicle and/or boat.
CALIFORNIA PROPOSITION 65 WARNING
WARNING: This product can expose you to chemicals, including carbon monoxide, which are
known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
WARNING: CONTAINS LEAD. MAY BE HARMFUL IF EATEN OR CHEWED. COMPLIES WITH
FEDERAL STANDARDS. KEEP OUT OF REACH OF CHILDREN.

3
WARNING
GENERAL WARNINGS
• Never use liquid propane gas in a unit designed for natural gas.
• Never use charcoal or wood briquette in a gas grill. Flavoring chips must be contained in a metal
smoking box to contain ash and prevent res.
• Leak test all connections before rst use, even if grill was purchased fully assembled.
• Never check for leaks using a match or open ame.
CAUTION: Strong odors, colds, sinus congestion, etc. may prevent the detection of natural gas.
Use caution and common sense when testing for leaks.
• Always keep your gas grill free and clear of gasoline, lighter uid, paint thinner, or other ammable
vapors and liquids or combustible materials.
• Always check the grill prior to each use as indicated in the “Pre-Start Check List” section of this
manual.
• DO NOT obstruct the ow of combustion or ventilation air.
• Keep children and pets away from hot grill. DO NOT allow children to use or play near this grill.
• DO NOT leave the grill unattended while in use.
• DO NOT allow the gas hose to come in contact with hot surfaces.
• DO NOT allow grease from drain hole to fall on hose.
• Keep any electrical supply cords away from water or heated surfaces.
• Keep a re extinguisher on hand acceptable for use with gas products. Refer to your local authority
to determine proper size and type.
• For household use only. DO NOT use this grill for anything other than its intended purpose.
• DO NOT use while under the inuence of drugs or alcohol.
• Grill is hot when in use. To avoid burns:
• DO NOT attempt to move the grill.
• Lock the wheels so the unit does not accidentally move.
• Wear protective gloves or oven mitts.
• DO NOT touch any hot grill surfaces.
• The outdoor cooking gas appliance and it’s individual shut-off valve must be disconnected from the
gas supply piping system during any pressure testing of that system at test pressure in excess of
0.5 psi (3.5kPa)
• The outdoor cooking gas appliance must be isolated from the gas supply piping system by closing
its individual manual shutoff valve during any pressure testing of the gas supply piping system at
test pressures equal to or less than 1/2 psi (3.5 kPa)
USE CAUTION AND COMMON SENSE WHEN OPERATING YOUR GAS GRILL.
FAILURE TO ADHERE TO THE SAFETY WARNINGS AND GUIDELINES IN THIS MANUAL
COULD RESULT IN SEVERE BODILY INJURY OR PROPERTY DAMAGE.
Connection should be made by a professional service technician. Supply the technician with a copy of these
instructions. Incorrect connection can result in a gas leak with possibility of re.
DANGER

4
PARTS CONTENTS
ASSEMBLY INSTRUCTIONS
YOU MUST BE A PROFESSIONAL SERVICE TECHNICIAN TO CONVERT THIS GRILL.
READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING OR OPERATING THE CONVERTED GRILL.
The following tools are required to assemble the Conversion Kit:
• Phillips and Flathead Screwdrivers • Adjustable Wrench • 3/4 Wrench
Inspect contents of the box to ensure all parts are included and undamaged.
This appliance was converted on ______________________(day-month-year)
to natural gas with Kit No. ACC6000AF by:
Name___________________________________________________________
Address_________________________________________________________
(name and address of organization making this conversion), which accepts the
responsibility that this conversion has been properly made.
Este electrodoméstico se convirtió el __________ __________(día-mes-año)
a gas natural con el kit No. ACC6000AF por:
Nombre_________________________________________________________
Dirección________________________________________________________
(nombre y dirección de la organización que realiza esta conversión), que
acepta la responsabilidad de que esta conversión se haya realizado
correctamente.
Cet appareil a été converti le __________ ______________(jour-mois-année)
en gaz naturelavec le kit n ° ACC6000AF par:
Nom___________________________________________________________
Adresse_________________________________________________________
(nom et adresse de l'organisation effectuant cette conversion), qui accepte la
responsabilité que cette conversion a été correctement faite.
ɌϬ.9 Ɍ1.2 Ɍ1.Ϭ5Ɍ1.46
LP NG LP NG
Main Burner
Input raƟng
Side Burner
6×ϴϱϬϬ BTU ϭϮϬϬϬ BTU
OrŝĮce size Ɍ1.Ϭ5Ɍ1.46
LP NG
Sear Burner
ϭϮϬϬϬ BTU

CAUTION: Some parts may contain
sharp edges. Wear
protective gloves if
necessary.
Note: Make sure all control knobs are
in the off position, LP tank valve
is closed and tank is
disconnected from regulator
and removed from grill.
Step 1
Using an adjustable wrench to hold
the gas manifold connection secure,
use a 3/4” wrench to loosen the hose
connection nut. Replace existing LP hose/
regulator assembly with natural gas 10’
hose assembly. Tighten the connection
carefully using two wrenches.
Step 2
Open hood and remove warming rack,
cooking grills and heat shields. Set aside
for later use.
5
CONVERSION
INSTRUCTIONS
GAS9670AS/ASO GAS MANIFOLD
10’ NATURAL GAS HOSE
GAS MANIFOLD

Step 3
Remove two screws from each burner
which are located in back of grill.
Remove burners from back of grill.
Step 4
Remove wing nut from side burner.
Carefully lift side burner up and away
from valve nozzle.
Use the gas orifice tool to remove the
LP brass orifice from the side burner
valve.
BURNER
KNOB
VALVE
NOZZLE
GAS
ORIFICE
TOOL
WING NUT
LP
BRASS
ORIFICE
6
DO NOT REMOVE
THE NATURAL GAS
ORIFICE

7
Step 5
Remove 2 screws from the back of the
sear burner. Carefully lift sear burner up
and away from the valve nozzle.
Remove sear burner and sear burner
grease tray.
Use gas orifice tool to remove the LP
Brass orice from the sear burner valve.
GAS ORIFICE TOOL
LP
BRASS
ORIFICE
REMOVE
SCREWS
DO NOT REMOVE
THE NATURAL GAS
ORIFICE

Step 6
Use the gas orifice tool to remove the
LP brass orifice from each main burner
valve, through the hole on the firebox
front panel.
Note: All orifices of the grill are
double orifices (LP gas and natural
gas). You only remove the LP gas
orifice tip.
Step 7
Make sure all control knobs are OFF,
then remove all control knobs.
Step 8
Tighten screw on each control valve
as shown in Figure 1. Replace control
knobs when finished.
Note: This screw regulates the low
flame setting for natural gas.
After replacing knobs you will
notice the knobs will stop at the
“MED” setting on the dial. This
is the correct low setting for
natural gas. Do not try to turn
the knob to “LO” setting.
Step 9
Carefully replace each burner, making
sure burner openings slide over valve
nozzles and burner holes are facing up.
Reattach burner screws and wing nut.
Make sure the ignitors and burners are in
the correct position and are not loose.
Step 10
Replace warming rack, cooking grills and
heat shields.
Note: Follow directions in the leak
testing section of this manual
before using this grill.
FIGURE 1
LP GAS
ORIFICE
SIDE VIEW FIREBOX
FRONT
PANEL
8
DO NOT
REMOVE THE
NATURAL GAS
ORIFICE

CONNECTING YOUR GRILL TO THE NATURAL GAS SOURCE
1. Coat pipe nipple with gas resistant teon tape or pipe dope. Tighten quick-disconnect coupling onto
pipe nipple that leads to natural gas supply (Figure A).
2. After grill is completely assembled, make sure natural gas supply valve is “OFF” and then connect
natural gas hose to socket. Push sleeve back on socket (Figure B) and insert plug until sleeve snaps
forward, locking plug into socket. Be sure to leak test these connections prior to use.
Pipe nipple
Quick-disconnect
coupling Plug
Push sleeve back to attach
Sleeve
Socket
Natural gas supply
Natural gas supply Hose
Hose
Insert cover when hose is disconnected
DISCONNECTING YOUR GRILL FROM THE NATURAL GAS SOURCE
1. Turn natural gas supply valve “OFF”
2. To disconnect, push sleeve back and pull plug out of sleeve.
(Figure A)
(Figure B)
Supply valve
Supply valve
Pipe Fitting Flare Fitting
When attaching the quick disconnect to your natural gas supply line, use a pipe 3/8” tting,
DO NOT use a are tting.
3/8” Pipe threads
9

10
AVOID HARD METAL PIPING
• DO NOT use hard metal piping of any kind to connect this converted natural gas grill. Use only
natural gas hose specied by the manufacturer. Using hard metal piping or convoluted metal
tubing is an unsafe practice. Movement of the grill can cause breakage of metal pipe.
WARNING
LEAK TESTING:
To prevent re or explosion hazard:
• DO NOT smoke or permit ignition sources in the area while conducting a leak test.
• Perform test OUTDOORS only in a well ventilated area.
• Never perform a leak test with a match or open ame.
• Never perform a leak test while the grill is in use or while grill is still hot.
DANGER
WHEN TO PERFORM A LEAK TEST:
• After assembling or converting your natural gas grill and before lighting for the rst time, even if
purchased fully assembled.
• Any time the gas components are replaced.
• Any time your grill has been moved.
• At least once per year or if your grill has not been used for more than 60 days.
WARNING
• Never use your grill without leak testing all gas connections and hoses. See the section on
“Leak Testing” in this manual for proper procedures.
• Visually inspect the hose assembly prior to each use for evidence of damage, excess wear or
deterioration. If found, replace the assembly before using your grill. Only the manufacturer’s
supplied replacement should be used.
• During assembly or conversion to natural gas, keep the supply hoses free of kinks and/or
damage.
WARNING

11
CHECKING FOR LEAKS:
1. Create a mixture of 50% water and 50% liquid dishwashing soap.
2. Open the lid.
3. Ensure all control knobs are set to the “OFF” position.
4. Ensure gas hose is tightly connected to gas source.
5. Turn on the fuel supply at the source.
6. Apply the soap water mixture to the following:
Hose connection to gas manifold.
Brass connections and quick
disconnect assembly.
The full length of gas supply hose.
Quick disconnect coupler.
7. Check each place listed (A–D) for growing bubbles
which indicates a leak.
8. Turn off gas supply at source.
9. Turn on control knobs to release gas pressure in hose.
10. Turn control knobs to “OFF” position.
11. Tighten any leaking connections.
12. Repeat soapy water test until no leaks are detected.
13. Turn off gas supply at source until you are ready to use your grill.
14. Wash off soapy residue with cold water and towel dry.
15. Wait 5 minutes to allow all gas to evacuate the area before lighting grill.
CAUTION: DO NOT use the grill if leaks cannot be stopped.
Note: The leak test must be performed in an area that has adequate lighting in order
to see if bubbles are developing.
D
C
B
A
Watch For Bubbles
D
A
C
B

12
LIGHTING INSTRUCTIONS:
Follow the instructions in your grill owners manual or on the control panel of the grill.
1. OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside
the grill. An explosion could occur if grill lid is down.
2. Check that all burner control knobs are turned to the “OFF” position.
3. DO NOT stand with head, body, or arms over the grill when lighting.
TURNING OFF THE GRILL:
1. Turn off the gas at the source.
2. Turn all burner control knobs to the “OFF” position.
CAUTION:
• The natural gas source should always be in the off,
or closed position when the grill is not in use.
• Refer to your grill owner’s manual for grill operating instructions.
•Apply conversion kit sticker to an area near the rating label to show
the grill has been converted for use with natural gas.
WARNING
WARNING
Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip
any of the warnings and instructions contained in the preceding sections of this manual.
Note: Observe ame height of main burner when lit:
Flame should be a Blue/Yellow color between
1”–2” when burner is on “HIGH”.
WARNING
Property damage, bodily harm, severe burns, and death could result from failure to follow these
safety steps. These steps should be performed after the grill has been assembled and prior to
each use. DO NOT operate this grill until you have read and understand ALL of the warnings and
instructions in this manual.
PRE-START CHECK LIST:
• Ensure that the grill is properly assembled.
• Inspect the gas supply hose for burns, chaffing, kinks, and proper routing before each use. If it is
evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the grill
being used.
• Leak check all gas connections and hose. See section on “Leak Testing”.
• Ensure that all electrical supply cords are properly grounded. Keep any electrical supply cord and the
fuel supply hose away from any heated surfaces. Hose should be at least 3 inches from hot surfaces.
• Position your grill on level ground in a well ventilated location, a safe distance from combustible
materials, buildings and overhangs.
• Properly place the empty grease tray under the grease drain hole in the bottom of the grill to catch
grease during use.
•DO NOT obstruct the ow of combustion and ventilation air.

OM9670AS/ASO
0918
Owner’s Manual for Model
Manual del Propietario para el Modelo
GAS9670AS/ASO
©2018 The Boltz Group
Addison, Texas 75001 U.S.A.
FOR REPLACEMENT PARTS
FOR COVERS, ACCESSORIES AND OTHER PRODUCTS, PLEASE VISIT US ONLINE AT:
www.embersgrills.com
PLEASE CONTACT EMBERS GRILLS
CUSTOMER SERVICE DEPARTMENT AT 1-855-735-9922 OR
EMAIL US AT: [e-mail].
HOURS OF OPERATION ARE 8:00A.M.TO 5:00P.M.
MONDAY THROUGH FRIDAY.
PARA PIEZAS DE REPUESTO
PÓNGASE EN CONTACTO CON EL DEPARTAMENTO DE
ATENCIÓN AL CLIENTE DE EMBERS GRILLS AL 1-855-735-
9922 O ENVÍENOS UN CORREO ELECTRÓNICO A:
[e-mail]. HORAS DE OPERACIÓN SON
8:00 a.m. A las 5:00 p.m. DE LUNES A VIERNES.