Members Mark 980296395 User manual

for
Member’s Mark [ 6 Pack Multipurpose Disc Light ]
Item Number : 980296395
Model Number : SA18-N21-6PK-TW
Customer Assistance (spare/replacement parts): 1-(888)-280-7088
or Email: [email protected]
THIS ASSEMBLY MANUAL CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Assembly Instructions & User’s Manual

1.
Before Assembly
Care & Use
Important Safety Information
Quality Statement
• Please read all instructions carefully before assembling this product.
• Where applicable, and for your safety, assembly by an adult is strongly recommended.
• Use only vendor-supplied hardware to assemble this item. Using unauthorized hardware
could jeopardize the structural integrity of the item.
• Hardware may loosen overtime. Periodically check that all connections are tight.
• [NOTE : Please add any additional required Safety information. These will be item depen-
dent and based upon factory and industry standard requirements & recommendations.]
• Use a soft, clean cloth that will not scratch the surface when cleaning.
• [NOTE : Please add any additional required Care & Use Instructions. These will be item
dependent and based upon factory and industry standard requirements & recommendations.]
• Remove all parts and hardware from the box. Place all items on a carpeted or scratch-free
work surface, as this will avoid damaging parts during assembly.
• The shipping box can provide an ideal work surface if none is available.
• Use the components and hardware lists below to identify, inventory and separate each of
the hardware and components included.
• To avoid accidentally discarding small components or hardware, do not dispose of any
packaging or contents of the shipping carton until assembly is complete.
• DO NOT USE power tools unless it is explicitly identified in this manual as required for use
during assembly. Power tools can damage the fasteners, hardware and/or components.
• Do not fully tighten all fasteners / screws until all parts are in place. Failure to follow these
instructions may cause the fasteners / screws to misalign during assembly.
Table of Contents
Quality Statement
Important Safety Information
Before Assembly
Care & Use
Product Information
Components
Hardware
Tools Needs for Assembly
Before Assembly
Assembly and installation
- A. Soil Ground Mount Installation
- B. Concrete Mount Installation
- C. Wall Mount Installation
Battery Precautions
Warning
- Care & Use Instructions
- Replacing the battery
..................................................................1
.................................................1
....................................................................1
...........................................................................1
...............................................................2
..........................................................................2
..............................................................................2
....................................................2
....................................................................3
......................................................3
...........................................3
..............................................4
.....................................................5
..............................................................6
...........................................................................6
........................................................6
............................................................6

3.
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Solar lights have a solar cell that converts sunlight into electricity that is used to
recharge the built-in battery each day. A built-in sensor automatically turns on the light
at night. The more sunlight is received during the day, the longer the light will operate.
How Solar lights Work
Choosing the Right Location
Your solar lights should be installed in an area that gets DIRECT SUNLIGHT.
Your solar lights will produce more hours of operation when installed in an area
which is free from cover, shade, or shadowing.
Note:
If the ground is hard and packed, moisten the ground with water before inserting the stake to avoid breakage.
Assembly and installation
Before Assembly
A. Soil Ground Mount Installation :
Step 5 Step 6 Step 7
Step 1 Step 2 Step 3 Step 4
Completed stake
assembly.
Turn “ON” the
transparent cover
switch at all times.
Push the stakes securely
into the ground.
Completed.
A few important things to remember prior to installation.
2.
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Phillips Screwdriver Electric Drill
Hardware
3/16" (4.5mm)
Masonry Drill Bit
Tools Needed for Assembly
Product Information
Size (D x W x H) : 4.56”x 4.56”x 4.68” (11.58 x 11.58 x 11.88 cm)
Height above ground : 1.14”(2.90 cm)
Weight : 0.395 LB (0.18kg)
Includes 1 x 3.7V Li-ion 1200mAh rechargeable battery
LED : 8 LEDs
Housing : 1. Metal : Oil-rubbed bronze
2. Plastic
Components
AB C 1 C 2
Transparent Cover
Switch
Disc Light
Qty：6
Connecting Board
Qty：6
Ground Stake Ground Stake
Qty：6 (pieces) Qty：6 (pieces)
H1H2
Screws
Qty：24
Screws Plugs
Qty：24

4. 5.
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
B
H2
H1 H2
3/16" (4.5mm)
Masonry Drill Bit
Step 2Step 1
Important: Use the connecting
board as a guide to drill four
3/16" (4.5mm) pilot holes into the
concrete at the desired location.
B. Concrete Mount Installation :
Step 3 Step 4 Step 5
Insert screws plugs (H2)
into the drilled holes on four
sides of connecting board.
Secure mounting bracket to
concrete with screws (H1).
Do not over tighten screws.
Completed so far...
Step 6 Step 7
Screw
H1
into
H2
Turn “ON” the
transparent cover
switch at all times.
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
B
Step 1
H1
C. Wall Mount Installation :
Important: Use the connecting
board as a guide to drill four
3/16" (4.5mm) pilot holes into the
concrete at the desired location.
Step 3 Step 4 Step 5
Step 6 Step 7
Insert screws plugs (H2)
into the drilled holes.
Secure mounting bracket to
brick with screws (H1). Do not
over tighten screws.
Completed so far...
Completed.Completed. Attach disc light onto
connecting board.
Attach disc light onto
connecting board.
3/16" (4.5mm)
Masonry Drill Bit
Connecting board(B):
both sides are usable
Connecting board(B):
both sides are usable
Step 2
(H2)
Screws Plugs
Qty: 4
(H1)
Screws
Qty: 4
(H2)
Screws Plugs
Qty: 4
(H1)
Screws
Qty: 4
Turn “ON” the
transparent cover
switch at all times.
If there are issues with assembly as shown,
rotate counterclockwise to attach.
If there are issues with assembly as shown,
rotate counterclockwise to attach.

6.
Warning
Care & Use Instructions
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Transparent
cover switch
(Turned OFF)
Battery
ON OFF
Disc Light
Remove
Remove
Remove
Remove
Replacing the battery
1. Remove battery compartment cover.
2. Remove old battery.
3. Insert one (1) new 3.7V 1200mAh battery (not included).
4. Make sure to follow the battery polarity guide when installing a new battery.
5. Replace battery compartment cover.
• Do not use alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
• Do not dispose of batteries in fire.
• Important : Use only 1 x 3.7V 1200mAh Li-ion rechargeable battery.
Battery Precautions
1. Use only the size and type of battery specified.
2. Always purchase the correct size and grade of battery.
3. Be sure to follow the correct polarity when installing the battery as indicated in the battery
compartment. A reversed battery may cause damage to the device.
4. Remove battery if product is to be left unused for an extended period of time