Mercia Garden Products 01DTOVAX0705SDFW-V1 User manual







 

 

7X5 OVERLAP APEX SHED














  



2mm Drill bit
x2 





























































 
















































¡





 
01DTOVAX0705SDFW-V1
01DTOVAX0705SDNW-V1
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Overall Dimensions:
Width = 1603mm
Depth = 2150mm
Height = 1918mm
Base Dimensions:
Width = 1456mm
Depth = 2066mm
Building Content:
Door Gable QTY 1
AI-01R11OVAGSD1410X1887-V1
Back Gable QTY 1
AI-01R11OVAGP1410X1887-V1
Plain Panel QTY 1
(QTY 2 WINDOWLESS ONLY)
AI-R11OVPP2070X1567-V1
Window Panel QTY 1
(WITH WINDOW ONLY)
AI-01R11OV2CW2070X1567-V1
1 2 3 4
Floor QTY 1
AI-R11OSBF1456X2066-V1
Roof QTY 2
PI-03-0387
Door QTY 1
AI-R11FBMBZBD660X1660-V1
5 6 7
10
11
12
13
14
Fascia 12x60x851mm QTY 4
S1260-851mm
Fixed Window Strip 12x30x546mm QTY 5 (WITH WINDOW ONLY)
S1230-546mm
Cover Trims 12x45x1575mm QTY 4
S1245-1575mm
Ridge Bar 28x28x2014mm QTY 1
F2828-2014mm
Finial QTY 2
SHED DIAMOND FINIAL
8
9
17
Door Beading Strip 12x28x1590mm QTY 2
S1228-1590mm
T Hinge QTY 3
PI-02-1042
Plastic Window Cill
(WITH WINDOW ONLY)
PI-08-0013
Felt
Styrene QTY 2
(WITH WINDOW ONLY)
PI-05-0114
18
20
21
L-Bracket QTY 2
PI-07-0012
16
Turn Button QTY 2
PI-07-0034
19
15
Eaves Frame 28x28x2090mm QTY 2
F2828-2090mm
Hasp and Staple QTY 1
PI-07-0207
Nail Bag
Felt Tacks x 70
30mm Screw x 84
50mm Screw x 32
40mm Screw x 44

¡
 
Pre Assembly
Before assembling remove the transportation
blocks from the bottom of each panel.
Take care removing the blocks as to not damage
the panels. Tap with a at headed screwdriver
and hammer.
Dispose of the blocks once removed.
Step 1
Parts needed - No. 5 QTY 1
Place the oor (No.5) on a rm and level base,
ensure the base has suitable drainage free from
areas where standing water can collect. See the
front page for base requirements.
5
Step 2
Parts needed - No. 1 QTY 1
No. 7 QTY 1
No. 15 QTY 3
Place the door (No. 7) within the door
aperture opening. Fix the T Hinges
(No.15) onto the door and Door Gable
as shown (taking into account on
which side of the Door Gable opening
you want the Door to open). Ensure
that the screws go through the cladding
and into the framing behind.
21x30mm screws
30mm
screw
Pre drill
hole
1
7
15
Opens from the Left Opens from the Right
IMPORTANT: Pre-drill before xing screws.
**PLEASE NOTE** Before tting the
hinges, ensure the door is in the correct
position depending on which side you
want the door to open. See external
illustrations below which show the
doors internal framing.


 
Step 3
Parts needed - No. 2 QTY 1
No. 3, (or 4) QTY 1
Fix the corners of the Back Gable (No.2) and
the Plain Panel (No.3) (or Window Panel)
with 50mm screws as shown in diagram.
Do not secure the building to the oor until
the roof is tted.
Position the panels so there is equal spacing
between the oor and cladding on all sides.
**Please note: Whether you have pur-
chased the with windows building or no
windows building, the panels are inter-
changeable. Decide which works best
before assembly.**
3x50mm Screws
3
2
Pre drill
hole
50mm
screw
IMPORTANT: Pre-drill before xing screws.
Use for no
window buildings
3
Step 4
Parts needed - No. 1 QTY 1
No. 4, (or 3) QTY 1
Fix the end of the Window Panel (No.4)
(or Plain Panel) to the corner of the
Back Gable (No.2) with 50mm screws
as shown in diagram.
Fix the corners of the Door Gable
(No.1) to the ends of the Side Panels
with 50mm screws as shown in
diagram.
Do not secure the building to the oor
until the roof is tted.
Position the panels so there is equal
spacing between the oor and clad-
ding on all sides.
9x50mm Screws
1
4
Pre drill
hole
50mm
screw
IMPORTANT: Pre-drill before xing screws.


 
Step 5
Parts needed - No. 12 QTY 1
No. 20 QTY 1
Place the ridge bar (No.12)in between
the Door Gable (No.1) and Back Gable
(No.2). Ensure the top corners of the
ridge bar sit ush with the top points of
the Gables. Fix the ridge bar to the gable
using one L bracket (No.20)for each end.
Fix with 4x30mm screws each.
8x30mm Screws
12
20
30mm
screw
Pre drill
hole
IMPORTANT: Pre-drill before xing screws. Step 6
Parts needed - No. 6 QTY 2
No. 13 QTY 2
Fix the eaves frames (No.13)to
each roof sheet (No.6)using
4x30mm screws per eave.
Place the Roof Sheets (No.6) on top
of the building. From the top, x
directly through the roof sheets
(No.6) and into the ridge bar
(No.12) below using 4x40mm
screws per roof sheet.
It is essential that the ridge bar
(No.12) and the roof panel pull
together when xed with 40mm
screws. You may require another
person pushing the ridge bar
(No.12) up from below to achieve
this.
**The edges of the roof sheets
must be ush with the outer clad-
ding of the Gable Tops.**
8x30mm Screws
28x40mm Screws
6
30mm
screw
40mm
screw
Pre drill
hole
IMPORTANT: Pre-drill before xing screws.
6
6
13


 
Step 7
Once the roof is xed
attach the building to the oor
with 50mm screws. Make sure
that you screw into the
framing below.
20x 50mm Screws
b
50mm
screw
Pre drill
hole
IMPORTANT: Pre-drill before xing screws.
18
Step 8
Parts needed - No. 18 QTY 1
Cut the felt (No.18) into 2 sheets measuring
2230mm (L) x 1000mm (W) and lay onto the
buildingin the order shown in the diagram,
ensuring there is 50mm overhang around the
sides.
Once the sheets are laid out, x them onto
the roof with felt tacks 100mm apart.
70 x Felt Tacks
Felt
tacks
100mm
HANDLE
WITH CARE
1 2
3
4
1
2


 
10
Step 9
Parts needed - No. 10
Fit the Cover Trims (No.10) to the front
and back of the building as shown in the
illustration using 30mm screws. Trim the
length of the cover trims to the required
size before tting if necessary.
12x30mm Screws
10
10
30mm
screw
Pre drill
hole
IMPORTANT: Pre-drill before xing screws.
*Cut down
trims to t
Step 10
Parts needed - No. 8 QTY 4
No. 14 QTY 2
Attach the fascias (No.8) to the
roof leaving a slight overhang at
the top.
Fit the fascias (No.8) to the roof
over the felt and secure in place
with 40mm screws as shown.
Fit the Finials (No.14) over the
fascias using 40mm screws.
16x40mm Screws
14
8
8
8
14
8
40mm
screw
Pre drill
hole
IMPORTANT: Pre-drill before xing screws.
Step 11
For a windowless version go to step 12
Parts needed - No. 9 QTY 5
No. 16 QTY 1
No. 19 QTY 2
Pre drill
hole
30mm
screw
9
9
16
a
b
c
d
SILICONE
SEALANT
9
9
9
Styrene
Window Cill
Cladding
Side View
19
19
Fix 2x window strips (No. 9) to the framing
along the outside edge of the window gap
using 3x30mm screws per strip.
Place the plastic cill (No. 16) into the window
panel as shown in the illustration and x
with 3x30mm screws per cill.
Fit the styrene sheets (No. 19) on top of the
window cill.
*For added weather protection t your
windows using silicone sealant around
the outside edges.
**When positioning the styrene sheets ensure
there is an equal distance on all sides.
Attach the remaining 3x window strips
(No. 9) to either side of the windows and the
centre. Secure into place using 3x30mm
screws per strip.
18x30mm Screws
a
b
c
d
IMPORTANT: Pre-drill before xing screws.

¢
 
Step 12
Parts needed - No. 11 QTY 2
Use 4x30mm Screws to x each
beading strip (No.11) onto the
door gable (No.1). Ensure that
the screw is parallel with the
door frame when xing the strip
to the door gable as shown in
the close up view.
8x30mm Screws
11
11
30mm
screw
Pre drill
hole
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
30mm
screw
IMPORTANT: Pre-drill before xing screws.
21
Step 13
Parts needed - No. 21 QTY 1
To x the lock in place. Screw the Staple
(No. 21) to the Door Gable making sure
that the screws go into the framing behind.
Check the Hasp (No. 21) is in line with the
staple and screw into the Door making
sure that the screws go into the framing
behind.
7x30mm screws.
Parts needed - No. 17 QTY 2
Fix the Turn Button (No. 17) onto
the door gable (No.1) using
1x30mm screw for each one.
2x30mm Screw
Step 14
17
30mm
screw
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole


 
It is ESSENTIAL that you apply wood
treatment immediately after the building
has been assembled.
AFTER TREATMENT:
score around protective
cover on glazing and
carefuly peel
covering back