Mercia Garden Products 01SHPWOR1010DDOW-V2 Instruction manual

01SHPWOR1010DDOW-V2
10X10 SHIPLAP WORKSHOP WITH DOUBLE DOOR, OPENING WINDOW, T&G ROOF & FLOOR
2mm Drill bit
x2 Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
All building’s should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
Please retain product label and instructions for future reference
General Instructions
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied)
including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm
bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather conditions.
For the duration of heavy or extended periods of rain, swelling of the wood panels may
occur. Warping of the wood may also occur during excessive dry spells due to an interior
moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is
suggested that the outdoor building is sprayed with water during extended periods of
warm sunshine and sheltered as much as possible during rain or snow.
Our buildings are pre treated with a water based treatment**; this only helps to protect
the product during transit and for upto 3 months against mould. To validate your
guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated
with a wood preserver within the rst three months of assembly and thereafter in
accordance with the manufactures recommendations. Care must be taken to ensure
the product is placed on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to
diagrams for the base dimensions, The base should be slightly smaller than the external
measurement of the building, i.e. The cladding should overlap the base, creating a run
o for water. It is also recommended that the oor be at least 25mm above the
surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
Refer to the instructions pages for you specic product code
**Protim Aquatan T5 (621)**
Your building has been treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct
application of Aquatan solution and then allowed to dry.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

H=220cm W=140cm L=130cm
30mm Black Screw x 12
P 2
01SHPWOR1010DDOW-V2
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Overall Dimensions:
Length = 3114mm
Width = 3179mm
Height = 2485mm
Base Dimensions:
Length = 3010mm
Width = 2980mm
Building content
2
13456
Plain Side
Qty 2
Window Side
Qty 2
Floor
Qty 4
Roof Panel
Qty 2
8
Front
Gable
Right
Front
Gable
Left
Front
Gable
Top
Back Gable
Right
Back Gable
Left
9
Truss Block - 160mm Qty 2
Door Gable Rail - 1332mm Qty 2
Tower Catch Block - 118mm Qty 2
14
11
12
15
13
17
Truss
Plain Gable Strip - 2387mm Qty 1
Cover Trim - 1757mm Qty 11
18
Finial
Qty 2
21
20 T Hinge
Qty 6
Felt
24
25
Casement stay
QTY 2
Butt hinge QTY 4
22
26
23
Tower Bolt QTY 2
27
7
10
Door
QTY 2
16
Door Gable Strip - 2552mm
Cover Strip - 2800mm Qty 3
19
Gable Block - 342mm
Plain Gable Board
28 Window
QTY 2
Hasp & Staple
Lock
Door Cloaking Strip
29
Nail Bag 30mm Screw x 91
20mm Screw x 12
50mm Screw x 82
70mm Screw x 6
40mm Screw x 106
Felt Tacks x 170
16mm Screws x 12
100mm Screw x 2
Remove transportation
blocks from the bottom
of each panel before
beginning assembly. Each
Panel should have two
blocks.
Pre Assembly
Door Gable Assembly
Step 1
2 x 50mm screws
Lay the Front Gable Right and Front Gable
top on a level oor place them next to each
other, ensure they are level at the top then
x together using 2x50mm screws. Stagger
the screws so they do not collide.
1
3
50mm
screw
Pre drill
hole

P 3
27
Step 2
2 x 50mm screws
Lay the Front Gable Left next to the Front
Top Gable, ensure they are level at the top
then x together using 2x50mm screws.
Stagger the screws so they do not collide.
2
50mm
screw
Pre drill
hole
Line the Door Gable Strip up to the
assembled gable at the corners as shown in
the illustration and x in place using 40mm
screws.
5x40mm Screws
40mm
screw
Pre drill
hole
Plain Gable Assembly
Step 3
12 x 50mm screws
Lay the Back Left Gable and Back Right
Gable on a level oor place them next to
each other, ensure they are level at the top
and bottom then x together using
10x50mm screws. Stagger the screws so
they do not collide.
50mm
screw
Pre drill
hole
5
4
12
Turn the gable section over
and secure the top board in
place using 3x30mm
screws. Ensure to screw into
the framing, pre-drilling to
avoind splitting the board.
3 x 30mm screws
50mm
screw
Pre drill
hole
16

P 4
32 x 40mm screws
Place oor on rm and level base, ensure
base has suitable drainage free from areas
where water can collect. (See front page on
base requirements).
Attach the oors using 32 x 40mm screws
8
40mm
screw
Pre drill
hole
8
Step 4
Do not secure the building to
the oor until the roof is tted.
Fix the corners with 50mm
screws as shown in diagram.
Position the panels so there is equal spacing
between the oor and cladding on all 4 sides
Step 5
3x50mm Screws
4
5
7
50mm
screw
Pre drill
hole
Step 6
Fix the remaining window side
and the splain side at the
corner with 50mm screws as
shown in diagram.
6x50mm Screws
50mm
screw
Pre drill
hole
7
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
6

P 5
*Cut down trims to t
Measure the length of the door
gable rail and cut down a strip
match.
Fix in place using 2x30mm
screws.
Step 7
Fix the remaining plain side with
50mm screws as shown in diagram.
3x50mm Screws
6
50mm
screw
Pre drill
hole
Step 8
Fix the Door Gable (refer to steps 1
and 2 if you have not already
assembled this) at the corners with
50mm screws as shown in diagram.
6x50mm Screws
50mm
screw
Pre drill
hole
Step 9
Fit the Door Gable Rail between the
Front Gable Left and Right. Fix to
the oor using 3x50mm screws.
Ensure screws line up with the
framing.
3x50mm Screws
50mm
screw
Pre drill
hole
15
19
50mm
screw
Pre drill
hole
2
1
3

70mm
screw
100mm
screw
Step 11
Place a Truss central to where two
panels join. Align the top of the
truss with the top of the sides as
shown in the diagram.
Tip - Use a piece from the xing kit
as a guide.
Pencil mark the truss position and
remove truss.
Place the truss blocks up to the
pencil mark and x using 2x70mm
screws per block.
Place the truss back into position on
top of the support block and secure
using 100mm screw each side from
the top down through the truss and
into the block.
4x70mm Screws
2x100mm Screws
14
Pre drill
hole
Pre drill
hole
11
11
*Cut down trims to t
Using x3 strips (No. 20) cut two trims at 1783mm and
one strip at 1445mm.
Place the smaller strip (1445mm) centrally above the
door aperture (allowing a space of 10mm between the
strip and the top of the door opening) and x into
position using 3x30mm screws.
Align the larger strips (1783mm) either side of the rst
smaller strip and x each one into position using
3x30mm screws. This will allow a space of
approximately 10mm between the trims and the
opening.
*Please note: This 10mm gap allows the doors to sit
onto the gable NOT into the aperture.
Fix the T Hinges onto the front of the doors; aligning
each hinge to the framing on the back of each door.
Secure the doors onto the assembled gable as shown
in the illustration. Ensuring that the screws go through
the cladding and into the framing behind.
51x30mm Screws
Step 10
30mm
screw
Pre drill
hole
19
19
19
20
10mm
gap

P 7
9
Step 12 Step 13
Place a roof sheet ontop of the
plain gable and truss making sure
the roof sheet sits into the gables
and x using 40mm screws. Ensure
there is an equal amount of
overhang on either side of the roof.
12x40mm Screws
40mm
screw
Pre drill
hole
Place the second roof sheet
ontop of the truss and ensure
that it butts up to the one
already xed. Following the
same method outlined in step
12.
12x40mm Screws
40mm
screw
Pre drill
hole

P 8
Step 14 Step 15
Once the roof is xed
attatch the building to the
oor with 50 mm screws.
36 x 50mm Screws
50mm
screw
Pre drill
hole
HANDLE
WITH CARE
12
3
4
170 x felt tacks
Cut four strips of felt and place
onto the roof. See below for
sizes.
Place the felt at onto the roof
in the order that is stated on
the diagram below.
Once the sheets are laid out x
them onto the roof with tacks
100mm apart.
12
34
Felt Strip Sizes
3210mm
Felt
tacks
B
BBBB
B
B

P 9
*Cut down trims to t
Step 16 Step 17
Fit the cover trims to the
building and secure in place
with 40mm screws as
shown.
Fit the Plain Gable Strip
where the two back gables
join using 4x40mm screws.
Pre drill to avoid splitting.
28x40mm Screws
19 17
17
40mm
screw
Pre drill
hole
16x40mm Screws
Fit the fascias to the roof
over the felt and secure in
place with 40mm screws as
shown.
Pre drill to avoid splitting.
Measure and trim down to
size.
40mm
screw
Pre drill
hole
17
17
17
17 17
17 21
17
17 21

c
Step 18 Step 19
19
28
30mm
16mm
Opening Window
Fixed Window
30mm
screw
30mm
screw
16mm
screw
30mm
screw
25
Place the cover strip 11mm above the
window gap in the window panel and
x with 3x30mm screws per strip.
Measure and trim before tting.
If you would like the windows to be
opening use the butt hinges to
attach the opening window strip
and the opening window together.
Use 30mm screws to x the butt
hinge to the Window Strip and
16mm screws to x it to the
Opening Window.
If you want to x the opening
windows, instead of xing butt
hinges to the opening window,
use 4x30mm screws to attach
the opening windows to the
window panel as shown in the
diagram.
3x30mm Screws
*SCREW COUNT PER WINDOW
6x30mm Screws
6x16mm Screws
4x30mm Screws
*Cut down trims to t
30mm
screw
Pre drill
hole
19
Place the Cloaking Strip to the
rear of one of the doors. Fixing in
position screwing through the door
into the cloaking strip with 3x30mm
screws.
Align the tower bolts onto the
vertical framing of the slave
door, secure the bolts to the
top and bottom using 6x30mm
black screws per tower bolt.
Mark the position of the bolt
& drill a hole above and below
for the bolt to catch in to.
15x30mm Black Screws
26
29