Mercia Garden Products 01DTPRMSHAX1010DDOP-V1 Instruction manual

REGISTER FOR YOUR
ANTI-ROT
GUARANTEE TODAY
PLEASE SCAN HERE:
**Protim Aquatan T5 (621)**
Your building has been dip treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct
application of Aquatan solution and then allowed to dry.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
Measure
under the
head
Measure
overall
length
Screws & Nails Bolts To identify the
xings required
for each step use a
measuring tape.
01DTPRMSHAX1010DDOP-V1
DIP TREATED PREMIUM SHIPLAP APEX 10X10 DOUBLE DOOR OPENING WINDOW
2mm Drill bit
x2 Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
All buildings should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-
driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
LOCATION FOR YOUR GARDEN BUILDING
A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,
annual treatment and to allow air ow around the building.
Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing
damage to the building.
TIMBER
As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy
or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during
excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be
helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine
and sheltered as much as possible during rain or snow.
Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent
the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.
Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-
ment to prevent water ingress
Pressure Treated buildings - Require a waterproof treatment to prevent water ingress
Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base
dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding
should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above
the surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or
using this product.
For ease of assembly, you
will need a tape measure to
check dimensions of
components.
P 1
Please retain product label and instructions for future reference
General Instructions

P 2
The building you have purchased can be built in two ways as an Apex or a Reverse Apex. Within this document there are seperate instructions to show how to install each style
please refer to the corresponding pages for the style you have chosen.
10X10 Apex
Overall Dimensions:
Width = 3229mm
Depth = 3028mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
Base Dimensions:
Width = 3064mm
Depth = 2976mm
12X10 Apex
Overall Dimensions:
Width = 3229mm
Depth = 3678mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
01DTPRMSHAX0210NWPB-V1 - QTY 1
Base Dimensions:
Width = 3064mm
Depth = 3572mm
Apex Page 6 - 16
14X10 Apex
Overall Dimensions:
Width = 3229mm
Depth = 4274mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
01DTPRMSHAX0210NWPB-V1 - QTY 2
Base Dimensions:
Width = 3064mm
Depth = 4168mm
15X10 Apex
Overall Dimensions:
Width = 3229mm
Depth = 4572mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
01DTPRMSHAX0510OPPB-V1 - QTY 1
Base Dimensions:
Width = 3064mm
Depth = 4466mm
16X10 Apex
Overall Dimensions:
Width = 3229mm
Depth = 4870mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
01DTPRMSHAX0210NWPB-V1 - QTY 3
Base Dimensions:
Width = 3064mm
Depth = 4764mm
18X10 Apex
Overall Dimensions:
Width = 3229mm
Depth = 5466mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
01DTPRMSHAX0210NWPB-V1 - QTY 4
Base Dimensions:
Width = 3064mm
Depth = 5360mm
20X10 Apex
Overall Dimensions:
Width = 3229mm
Depth = 6062mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
01DTPRMSHAX0510OPPB-V1- QTY 1
01DTPRMSHAX0510SDPB-V1 - QTY 1
Base Dimensions:
Width = 3064mm
Depth = 5956mm
01DTPRMSHAX1010DDOP-V1
Please retain product label and instructions for future reference

P 3
Please retain product label and instructions for future reference
The building you have purchased can be built in two ways as an Apex or a Reverse Apex. Within this document there are seperate instructions to show how to install each style
please refer to the corresponding pages for the style you have chosen.
Reverse Apex Page 17 - 27
10X10 Reverse Apex
Overall Dimensions:
Width = 3229mm
Depth = 3028mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
Base Dimensions:
Width = 3064mm
Depth = 2976mm
12X10 Reverse Apex
Overall Dimensions:
Width = 3229mm
Depth = 3678mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
01DTPRMSHAX0210NWPB-V1 - QTY 1
Base Dimensions:
Width = 3064mm
Depth = 3572mm
14X10 Reverse Apex
Overall Dimensions:
Width = 3229mm
Depth = 4274mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
01DTPRMSHAX0210NWPB-V1 - QTY 2
Base Dimensions:
Width = 3064mm
Depth = 4168mm
15X10 Reverse Apex
Overall Dimensions:
Width = 3229mm
Depth = 4572mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
01DTPRMSHAX0510OPPB-V1 - QTY 1
Base Dimensions:
Width = 3064mm
Depth = 4466mm
16X10 Reverse Apex
Overall Dimensions:
Width = 3229mm
Depth = 4870mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
01DTPRMSHAX0210NWPB-V1 - QTY 3
Base Dimensions:
Width = 3064mm
Depth = 4764mm
18X10 Reverse Apex
Overall Dimensions:
Width = 3229mm
Depth = 5466mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
01DTPRMSHAX0210NWPB-V1 - QTY 4
Base Dimensions:
Width = 3064mm
Depth = 5360mm
20X10 Reverse Apex
Overall Dimensions:
Width = 3229mm
Depth = 6062mm
Height = 2504mm
Pack Requirement:
01DTPRMSHAX1010DDOP-V1 - QTY 1
01DTPRMSHAX0510OPPB-V1 - QTY 1
01DTPRMSHAX0510SDPB-V1 - QTY 1
Base Dimensions:
Width = 3064mm
Depth = 5956mm

P 4
Please retain product label and instructions for future reference
21
89
3
4
Plain Panel
AI-S21SHPPTF1490X1784-V1
QTY 4
Window Side Panel
AI-01S21SH1LFW1490X1784-V1
QTY 2
Floor
AI-S21MBF1529X1485-V2
QTY 4
Roof Panel
AI-S21MBOHAR1529X1760-V1
QTY 4
5
Small Plain Panel
AI-S21SHPPTF745X1784-V1
QTY 2
Right Gable
AI-S21SHHAGTR1534X680-V1
QTY 2
Double Door Panel
AI-01S21SHDD1490X1784-V1
QTY 1
76
Door
AI-S21FBMBZBD600X1720-V1
QTY 2
Window
AI-FW1000X540-V1
QTY 2
10
Truss Block - 44x44x140mm - QTY 2
F4444-G-160mm
11
12
13
14
15
16
17
30
Butt Hinge - QTY 4
PI-07-0066
18
19
20
21
22
Casement stay - QTY 2
PI-07-0007
26
28
T Hinge - QTY 6
PI-07-0021
Tower Bolt - QTY 2
PI-07-0030
29
Felt
33
Truss Support- AI-S22HAXT1651X88-V1 - QTY 2
Left Gable
AI-S21SHHAGTL1534X680-V1
QTY 2
Truss Brace - 27x44x1700mm - QTY 2
F2744-G-1740mm
Truss Support Triangle - 12x503mm - QTY 2
MB12-P-503mm
Door Cloaking Strip - 27x44x1658mm - QTY 1
F2744-1658mm
Door Beading Strip - 12x30x1600mm - QTY 2
S1230-1600mm
Window Strip - 12x56x1038mm - QTY 2
S1256-1038mm
Cover Strip - 12x56x2500mm - QTY 4
S1256-2500mm
Cover Strip - 12x56x1774mm - QTY 6
S1256-1774mm
Fascias - 12x60x1766mm - QTY 4
S1260-G-1766mm
27
U Channel - QTY 2
PI-07-0013
Building content - Pack A
01DTPRMSHAX1010DDOP-V1
Hasp and Staple Lock
PI-07-0221
32
31
Weatherproof Lock - QTY 1
PI-07-0222
23
Door Block - 27x44x150mm - QTY 2
F2744-150mm
24
Floor Block - 27x44x400mm - QTY 10
F2744-400mm
Gable Point - 12x417mm - QTY 2
WBP-417mm
Finial - QTY 2
Shed Diamond FInial
25
Gable Support - 27x44x780mm - QTY 2
F2744-G-820mm
Turn Button - QTY 2
PI-07-0034
34
Nail Bag
30mm Screw x 158
50mm Screw x 104
70mm Screw x 4
40mm Screw x 96
Felt Tacks x 150
16mm Screws x 12
100mm Screw x 2
There may be extra screws present in the nail bag
60mm Bolt x 8

Please retain product label and instructions for future reference
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-
driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
LOCATION FOR YOUR GARDEN BUILDING
A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,
annual treatment and to allow air ow around the building.
Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing
damage to the building.
TIMBER
As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy
or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during
excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be
helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine
and sheltered as much as possible during rain or snow.
Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent
the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.
Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-
ment to prevent water ingress
Pressure Treated buildings - Require a waterproof treatment to prevent water ingress
Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base
dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding
should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above
the surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or
using this product.
Turn Button - QTY 2
PI-07-0034
34
P 5
Building content - Pack B
01DTPRMSHAX0210NWPB-V1
Building content - Pack C
01DTPRMSHAX0510OPPB-V1
Building content - Pack D
01DTPRMSHAX0510SDPB-V1
Plain Side Panel
AI-S21SHPPTF596X1784-V1
QTY 2
2ft Roof
AI-S21MBOHAR596X1760-V1
QTY 2
2ft Floor
AI-S21MBF1529X596-V1
QTY 2
Single Door Panel
AI-01S21SHSD1490x1784-V1
QTY 1
5ft Floor Panel
AI-S21MBF1529X1485-V2
QTY 2
5ft Roof Panel
AI-S21MBOHAR1490X1760-V1
QTY 2
36 37
38
39
35
40
Pad Bolt
PI-07-0035
Truss Brace - 27x44x1700mm - QTY 2
F2744-G-1740mm
Truss Block - 44x44x140mm - QTY 2
F4444-G-160mm
Truss Support Triangle - 12x503mm - QTY 2
MB12-P-503mm
11
19
22
24
14
Truss Support - AI-S22HAXT1651X88-V1 - QTY 2
Cover Strip - 12x56x1774mm - QTY 2
S1256-1774mm
27
U Channel - QTY 2
PI-07-0013
2
1
Plain Panel
AI-S21SHPPTF1490X1784-V1
QTY 1
Window Side Panel
AI-01S21SH1LFW1490X1784-V1
QTY 1
Window
AI-FW1000X540-V1
QTY 1
10
Truss Brace - 27x44x1700mm - QTY 2
F2744-G-1740mm
Truss Block - 44x44x140mm - QTY 2
F4444-G-160mm
Truss Support Triangle - 12x503mm - QTY 2
MB12-P-503mm
11
19
22
24
14
Truss Support - AI-S22HAXT1651X88-V1 - QTY 2
Cover Strip - 12x56x1774mm - QTY 2
S1256-1774mm
Window Strip - 12x56x1038mm - QTY 1
S1256-1038mm
13
27
U Channel - QTY 2
PI-07-0013
Casement stay - QTY 1
PI-07-0007
Butt Hinge - QTY 2
PI-07-0066
30
26
5ft Floor Panel
AI-S21MBF1529X1485-V2
QTY 2
2
Plain Panel
AI-S21SHPPTF1490X1784-V1
QTY 1
5ft Roof Panel
AI-S21MBOHAR1490X1760
QTY 2
38
6
Door
AI-S21FBMBZBD600X1720-V1
QTY 2
Truss Brace - 27x44x1700mm - QTY 2
F2744-G-1740mm
Truss Block - 44x44x140mm - QTY 2
F4444-G-160mm
Truss Support Triangle - 12x503mm - QTY 2
MB12-P-503mm
11
19
22
24
14
Truss Support - AI-S22HAXT1651X88-V1 - QTY 2
Cover Strip - 12x56x1774mm - QTY 2
S1256-1774mm
Door Beading Strip - 12x30x1600mm - QTY 2
S1230-1600mm
12
28
T Hinge - QTY 3
PI-07-0021
27
U Channel - QTY 2
PI-07-0013
Door Block - 27x44x150mm - QTY 1
F2744-150mm
20
55
17 Floor Block - 27x44x400mm - QTY 2
F2744-400mm
17 Floor Block - 27x44x400mm - QTY 5
F2744-400mm 17 Floor Block - 27x44x400mm - QTY 5
F2744-400mm
Nail Bag
30mm Screw x 34
50mm Screw x 12
70mm Screw x 4
40mm Screw x 40
100mm Screw x 2
There may be extra screws present in the nail bag Nail Bag
There may be extra screws present in the nail bag
Nail Bag
There may be extra screws present in the nail bag
Felt Tacks x 35
30mm Screw x 43
50mm Screw x 16
70mm Screw x 4
40mm Screw x 56
100mm Screw x 2
Felt Tacks x 75
16mm Screws x 6 30mm Screw x 54
50mm Screw x 16
70mm Screw x 4
40mm Screw x 56
100mm Screw x 2
Felt Tacks x 75

P 6
Please retain product label and instructions for future reference
Pre Assembly
Before assembling remove the transportation
blocks from the bottom of each panel.
Take care removing the blocks as to not damage
the panels. Tap with a at headed screwdriver
and hammer.
Dispose of the blocks once removed.
Apex Installation
Parts needed
QTY 2
10x10 12x10 14x10 15x10 16x10 18x10 20x10
QTY 12
QTY 2
QTY 24
QTY 1
QTY 2
QTY 36
QTY 2
QTY 3
QTY 24
QTY 2
QTY 48
QTY 3
QTY 2
QTY 60
QTY 4
QTY 4
QTY 36
No.5
40mm Screw
No.36
Building Size
Step 1
Lay the oors (No.5, No.36) along side
each other as shown in the diagram, with
the framing down to the oor. Secure the
oors together using 6x40mm screws per
join. Ensure to go through the oor
cladding and into the framing.
Repeat the Step to create a second oor.
40mm
screw Pre drill
hole
16x10
20x10
12x10
36
5
5
5
5
5
5
36
5
5
36
36
5
5
NOT ALL SIZE OPTIONS ARE SHOWN BELOW,
THE ILLUSTRATIONS ARE EXAMPLES.
Step 2 Building Size
Parts needed
QTY 12
10x10 12x10 14x10 15x10 16x10 18x10 20x10
QTY 48
QTY 14
QTY 56
QTY 16
QTY 64
QTY 18
QTY 72
QTY 18
QTY 72
QTY 20
QTY 80
QTY 24
QTY 96
No.17
40mm Screw
Place the assembled oors along side each
other as shown in the diagram, locate the
Floor blocks (No.17) between the
assembled oors, equally spaced. Secure
the blocks to the oors using 4x40mm
screws per block, going through the oor
cladding and into the blocks bellow
40mm
screw Pre drill
hole
20x10
10x10
NOT ALL SIZE OPTIONS ARE SHOWN BELOW,
THE ILLUSTRATIONS ARE EXAMPLES.
12x10
16x10
5
5
5
5
17
17
17
17
17
17
17
17
17
17

P 7
Please retain product label and instructions for future reference
Locate the Plain Panels (No. 2) onto the oor. Fix
together using 4x50mm screws in an alternating
pattern
Locate the Window Panel (No. 1) onto the oor.
Fix to the plain panel at the corner with 4x50mm
screws as shown in diagram.
Do not secure the building to the oor until the
roof is tted
Position the panels so there is equal spacing
between the oor and cladding on all sides
Step 3
50mm
screw Pre drill
hole
1
a
a
a
2
2
Parts needed
QTY 1
All Sizes
QTY 8
QTY 2
No.1
No.2
50mm Screw
a
a
Building Size **Please note: Panels No.1/ No.2/ No.3/ No.4/ No.35/ No.39 are
interchangeable and can be positioned in a variety of congurations.
Decide which works best before assembly**
a
a
a
a
a
Parts needed
QTY 1
All Sizes
QTY 4
No.2
50mm Screw
Locate the Plain Panel (No.2) onto the oor.
Fix the corners of the assembled back plain
Panels with 50mm screws as shown in
diagram.
Do not secure the building to the oor until
the roof is tted
Position the panels so there is equal
spacing between the oor and
cladding on all sides
Step 4
2
50mm
screw Pre drill
hole
Building Size **Please note: Panels No.1/ No.2/ No.3/ No.4/ No.35/ No.39 are
interchangeable and can be positioned in a variety of congurations.
Decide which works best before assembly**
NOT ALL SIZE OPTIONS ARE SHOWN BELOW,
THE ILLUSTRATIONS ARE EXAMPLES.
Locate the Panels (No.1/No.2/No.35/No.39) onto the
oor. Fix the Panels together with 4x50mm screws per
join in an alternating pattern as shown in diagram.
Do not secure the building to the oor until the roof
is tted
Position the panels so there is equal spacing
between the oor and cladding on all sides
50mm
screw Pre drill
hole
Step 5
Parts needed
QTY 1
10x10 12x10 14x10 15x10 16x10 18x10 20x10
QTY 8
QTY 1
QTY 16
QTY 1
QTY 24
QTY 2
QTY 16
QTY 1
QTY 32
QTY 1
QTY 40
QTY 2
QTY 24
No.1
No.2
50mm Screw
QTY 1 QTY 1 QTY 1 QTY 2 QTY 1 QTY 1 QTY 3
No.39
QTY 2 QTY 4 QTY 6 QTY 8
No.35
QTY 1
1
2
a
a
a
a
1
2
35
35
35
35
35
35
16x10 Floor
39
1
2
1
2
2
20x10 Floor
1
2
35
35
12x10 Floor
a
a
a
a
Building Size
**Please note: Panels No.1/ No.2/ No.3/ No.4/ No.35/ No.39 are
interchangeable and can be positioned in a variety of congurations.
Decide which works best before assembly**

Please retain product label and instructions for future reference
P 8
Building Size
Building Size
4
4
Locate the Door Panel (No.3) and the Small
Plain panels (No.4) onto the oor. Fix the
Panels together at the corners using 4x50mm
screws per Corner
Do not secure the building to the oor until
the roof is tted
Position the panels so there is equal spacing
50mm
screw Pre drill
hole
Step 6
Parts needed
QTY 1
All Sizes
QTY 16
QTY 2
No.3
No.4
50mm Screw
3
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Building Size
8
Parts needed
QTY 2
All Sizes
QTY 8
QTY 2
No.8
No.18
30mm Screw
QTY 2
No.9
QTY 20
50mm Screw
QTY 2
No.23
Step 7
Lay the Gable tops (No.8 and No.9)
along side each other as show in the
diagram, secure together using 4x50mm
screws in an alternating pattern
Secure the Gable support (No.18) to the
gable tops, ensuring it sits ush with the
framing, secure using 6x50mm screws
going through the support and into the
gable framing behind.
Finally secure Gable Point (No.23) to the
top of the gables, secure using 4x30mm
screws going through the cladding and
into the gable framing
Repeat Step to create two assembled
gables
a
b
c
a
b
c
23
9
18
Locate the Assembled Gable tops (No.8
and No.9) onto the tops of the front and
back panels. Fix the gable tops to the
panels bellow using 8x50mm screws per
Gable top in an alternating pattern as
shown in the diagram
Do not secure the building to the oor
until the roof is tted
50mm
screw Pre drill
hole
Step 8
Parts needed
QTY 2
All Sizes
QTY 16
QTY 2
No.8
No.9
50mm Screw
Building Size
Parts needed
QTY 2
10x10 12x10 14x10 15x10 16x10 18x10 20x10
QTY 4
QTY 4
QTY 8
QTY 6
QTY 12
QTY 4
QTY 8
QTY 8
QTY 16
QTY 10
QTY 20
QTY 6
QTY 12
No.11
No.19
40mm Screw
QTY 2 QTY 4 QTY 6 QTY 4 QTY 8 QTY 10 QTY 6
QTY 4 QTY 6 QTY 8 QTY 10
No.24
QTY 24
30mm Screw QTY 8 QTY 16 QTY 24 QTY 16 QTY 32 QTY 40
QTY 2 QTY 4 QTY 6
Step 9
To construct the truss, secure the
Truss supports (No. 11) together
as shown with 2x30mm screws.
Secure the Truss Brace (No. 19) to
both sides of the Truss support
making sure to stagger the
4x40mm screws.
Finally secure the Truss support
triangle (No. 24) to both sides
with 3x30mm screws.
Repeat Step to create the
remaining trusses required for
each size
30mm
screw Pre drill
hole
30mm
screw Pre drill
hole
11
11
40mm
screw Pre drill
hole
19
19
24
24
a
ab
b
c
c

P 9
Please retain product label and instructions for future reference
22 22
Step 10
Place an assembled Truss central to where two
panels join. Align the top of the truss one inch
(25mm) below the top of the sides as shown in
the diagram.
HINT - Use a piece from the xing kit as a
guide.
Pencil mark the truss position and remove
truss.
Place the truss blocks (No. 22) up to the pencil
mark and x using 2x70mm screws per block.
Place the truss back into position on top of the
support block and secure using 100mm screw
each side from the top down through the truss
and into the block.
10X10
70mm
screw
100mm
screw
Pre drill
hole
Parts needed
QTY 1
10x10 12x10 14x10 15x10 16x10 18x10 20x10
QTY 2 QTY 3 QTY 2 QTY 4 QTY 5 QTY 3
Assembled Truss
No.22 QTY 2 QTY 4 QTY 6 QTY 4 QTY 8 QTY 10 QTY 6
QTY 12
70mm Screw QTY 4 QTY 8 QTY 12 QTY 8 QTY 16 QTY 20
QTY 6
QTY 2 QTY 4 QTY 6 QTY 4 QTY 8 QTY 10
100mm Screw
20X10
16X10
12X10
22
22
11
11
22
22
22
11
11
22
22
11
11
22
22
11
11
22
22
22
11
11
11
11 11
11
11
11 22
22
22
22
22 11
11
22
22 11
11
22
Building Size
Parts needed
QTY 2
10x10 12x10 14x10 15x10 16x10 18x10 20x10
QTY 10
QTY 2
QTY 20
QTY 2
QTY 30
QTY 2
QTY 20
QTY 2
QTY 40
QTY 2
QTY 50
QTY 2
QTY 30
No.7
No.27
30mm Screw
QTY 1 QTY 2 QTY 3 QTY 2 QTY 4 QTY 5 QTY 3
No.38
QTY 1 QTY 2 QTY 3 QTY 4
No.37
QTY 1 QTY 2
Step 11
Place the roof panels (No. 7, No. 37 and
No. 38) ontop of the building and truss
making sure the roof panels sit into the
gables and truss. Do not x the roof panels
until all roof panels are in place.
Ensure there is an equal amount of roof
overhang on either side of the building.
Secure the roof panels (No. 7, No. 37 &
No. 38) together using the metal U
channel (No. 27) and 10x30mm screws
per U channel.
30mm
screw Pre drill
hole 27
10X10
20X10
16X10
12X10
NOT ALL SIZE OPTIONS ARE SHOWN BELOW,
THE ILLUSTRATIONS ARE EXAMPLES.
7
37
7
7
37
7
3737
7
7
7
7
38
38
Building Size

Please retain product label and instructions for future reference
Step 12
27
10X10
30mm
screw Pre drill
hole
7
7
NOT ALL SIZE OPTIONS ARE SHOWN BELOW,
THE ILLUSTRATIONS ARE EXAMPLES.
Parts needed
QTY 2
10x10 12x10 14x10 15x10 16x10 18x10 20x10
QTY 10
QTY 2
QTY 20
QTY 2
QTY 30
QTY 2
QTY 20
QTY 2
QTY 40
QTY 2
QTY 50
QTY 2
QTY 30
No.7
No.27
30mm Screw
QTY 1 QTY 2 QTY 3 QTY 2 QTY 4 QTY 5 QTY 3
No.38
QTY 1 QTY 2 QTY 3 QTY 4
No.37
QTY 1 QTY 2
Place the roof panels (No. 7, No. 37 & No.
38) ontop of the building and truss
making sure the roof panels sit into the
gables and truss. Do not x the roof panels
until all roof panels are in place.
Ensure there is an equal amount of roof
overhang on either side of the building.
Secure the roof panels (No. 7, No. 37 & No.
38) together using the metal U channel (No.
32) and 10x30mm screws per U channel.
7
37
7
3737
7
7
37
7
7
20X10
16X10
12X10
38
38
Building Size
Ensure there is an equal amount of roof
overhang on either side of the building.
Fix the Roof using 40mm screws, ensuring
to x into the truss framing and gable tops.
Parts needed 10x10 12x10 14x10 15x10 16x10 18x10 20x10
QTY 32 QTY 48 QTY 64 QTY 48 QTY 80 QTY 96 QTY 64
40mm Screw
Step 13
40mm
screw Pre drill
hole
NOT ALL SIZE OPTIONS ARE SHOWN
BELOW, THE ILLUSTRATIONS ARE
EXAMPLES.
10X10
20X10
16X10
12X10
Building Size
P 10