Mercia Garden Products 0619LOG003-V5 Instruction manual

2mm Drill bit
MUST CAUTION
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
TIMBER
BUILDING A BASE
TYPES OF BASE
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
Refer to the instructions pages for your specic product code
NOT
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk

13
Gable 3296mm
AI-0619LOG002G
QTY 2
4Starter Board - 66x19x3296mm QTY 2
LB19RT66-A-3296
5
Log Board - 120x19x2996mm QTY 26
LB19-A-2996
6
Log Board - 120x19x1402mm QTY 6
LB19-B-1402
7
Log Board - 120x19x326mm QTY 30
LB19-B-326
8
Log Board - 120x19x326mm QTY 12
LB19-C-326
Log Board - 120x19x3296mm QTY 19
LB19-A-3296
Log Board - 120x19x1123mm QTY 24
LB19-B-1123
Roof Purlin - 90x40x3000mm QTY 3
F4090-3000
Bearer - 44x44x3011mm QTY 10
F4444-3011-PT
Bearer - 44x44x2799mm QTY 2
F4444-2799-PT
Fascia - 120x12x1775mm QTY 4
S12-G-120-1775 (1x14° Cut)
Floor Board - 121x12x2760mm QTY 29
MB12-2760
Roof Board - 121x12x1752mm QTY 56
MB12-1752
21
Short Window Pack*
QTY 2 Double Door Pack*
Closure Trim - 16x28x2400mm (approx length) QTY 14
S1628-2400
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Storm Brace - 27x44x2000mm QTY 8
F2744-2000
21
Log Board - 120x19x3296mm QTY 1
LB19-AD-3296
Log Board - 110x19x2996mm QTY 1
LB19RG110-AD-2996
*All components for the Windows and Doors are shown
in the Windows and Doors instruction packs.
9
10
11
12
13
14
15
16
17
19
20
Eaves Frame - 27x44x3000mm QTY 2
F2744-3000
18

Log Board - 110x19x2996mm QTY 1
LB19RG110-A-2996
Felt
Felt Tacks x200
70mm Screw x72
Nail Bag
40mm Screw x396
30mm Screw x102
60mm Bolt Set x16
Pre-assembly
*Please note:
Each board interlocks at
either end in a staggered pattern.
Before securing ensure that the boards
are tted properly in their respective
tongues and grooves.
22
Roof Spacers QTY 5
PI-07-0208 (20x100x2mm)
23
24

13 14
13
14
13
13
13
13
13
13 13 13
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
70mm
screw
a
Step 1
Parts Needed - No. 13 QTY 10
No. 14 QTY 2
No’s. 13 &
14
free from areas where standing
water can collect
8x70mm Screws
Pre drill
hole
70mm
screw
b
No. 14
*Ensure there is an equal
amount of space between
each frame.
44x70mm Screws
13
14
13
5
5
4
4
4
Pre drill
hole
70mm
screw
Step 2
Parts Needed - No. 4 QTY 2
No. 5 QTY 2
No’s. 4
& 5
*Ensure the notches at either
end of each board are ush
and level with the ends of the
frame.
4x70mm Screws
IMPORTANT: Pre-drill before xing screws.
a
b
Example picture
2 screws per bearer per end
13

6
9
5
5
7
Step 3
Parts Needed - No. 5 QTY 12
No. 6 QTY 6
No. 7 QTY 6
No. 9 QTY 6
Pre-Assembly
No’s. 5, 6, 7
& 9)
*Ensure that the boards are
level and ush with each
other as you lay each one.
Step 4
off
of the starter (No.
2)
*Please note: This image is for illustra-
tive purposes and may differ from your
choice in product (regarding door
position). Nevertheless the process of
tting the door frame is the same.
**Please Note: The short boards at the
front of the building (either side of the
door and window opening’s) can be
placed either side depending on your
needs.
7
7
10
5
9
8
Step 5
Parts Needed - No. 5 QTY 6
No. 7 QTY 13
No. 8 QTY 7
No. 9 QTY 7
No. 10 QTY 12
Pre-Assembly
No’s. 5, 7,
8, 9 & 10
*Ensure that the boards are
level and ush with each
other as you lay each one.
*Doors can be hung once the
boarding has enclosed the
door frame by 13-14 boards,
refer to Door installation
instructions, if not, you can
install the doors at Step 7
10
Step 6 (See Window-Assembly)
Parts needed - No. 1 QTY 2

10
10
95
7
7
8
Step 7
sNo. 1
*Ensure the boards are level with
each end.
*Please note: This image is for
illustrative purposes and may
differ from your choice in product
(regarding window position).
Nevertheless the process of tting
the window is the same.
Step 8
Parts Needed - No. 5 QTY 6
No. 7 QTY 11
No. 8 QTY 5
No. 9 QTY 5
No. 10 QTY 12
Pre-Assembly
No’s. 5, 7,
8, 9 & 10
*Ensure that the boards are
level and ush with each
other as you lay each one.
*Doors can be hung once the
boarding has enclosed the
door frame.
9
20
21
23
3
3
Step 9
Parts Needed - No. 9 QTY 1
No. 24 QTY 1
No. 20 QTY 1
No. 21 QTY 1
Pre-Assembly
No’s. 9
& 20
No’s. 24 & 21
*Ensure that the boards are
level and ush with each
other as you lay each one.
Step 10
Parts Needed - No. 3 QTY 2
No. 3
*Ensure that the boards are
level and ush with each
other as you lay each one.
4x70mm Screws
Pre drill
hole
70mm
screw

Front roof boards
Front view 23b 18
18
Pre drill
hole
70mm
screw 12
12
12
a
b
Step 11
Parts needed - No. 12 QTY 3
sNo.
12
ensure to
pre-drill to avoid the boards
splitting
*Please note: The gable shown is for
illustrative purposes and may differ
in width from your choice in
product.
Nevertheless, despite any
differences
the process of xing the
is the same.
12x70mm Screws
a
b
IMPORTANT: Pre-drill before xing screws.
40mm
screw
Pre drill
hole
Cut to t
Step 12
Parts needed - No. 18 QTY 56
No. 18
No. 24
*Ensure the roof boards meet at
the top of the apex and leave an
overhang at the bottom.
a
b
a
b
*Please Note: This image is for
illustrative purposes and may
differ from your choice in product.
Nevertheless the process of
cutting and tting the last roof
board(s) is the same.
168x40mm Screws

17
17
16
Step 13
Parts Needed - No. 16 QTY 2
No. 16
*Please Note: This image is for
illustrative purposes and may
differ from your choice in
product. Nevertheless the process
of xing the eaves frames is the
same.
18x30mm Screws
30mm
screw
Pre drill
hole
Step 14
Parts Needed - No. 17 QTY 29
No. 17
internally
*Do NOT secure the boards until
the last board has been measured
and cut.
on the last
board placed
No. 17
**Please note: Mark the nal board
2mm under the measurement; This
will allow the timber to expand and
contract correctly.
***Please Note: Ensure to screw
through each of the oor boards
into the oor bearers.
216x40mm Screws
40mm
screw
Pre drill
hole
Cut to t

HANDLE
WITH CARE
12
3
4
1. 2.
3. 4.
5.
Closure Trim
Internal
23
*Measure and cut the
closure trims to
t the internal space.
23
23
Closure Trim
Internal
11
*Measure and cut the
closure trims to
t the internal space.
11
11
RoofRoof
Pre drill
hole
30mm
screw
trim to t
Step 15
Parts needed - No. 11 QTY 7
No. 11
42x30mm Screws
30mm
screw
Pre drill
hole
Cut to t
Step 16
Parts needed - No. 11 QTY 7
No. 11)
internally
*Do NOT x the closure trim to the oor
boards.
42x30mm Screws
Felt
tacks
Step 17
Parts needed - No. 22
*Ensure there is approximately 50mm
of overhanging felt each side.
*Felt size: 3120mm
170x Felt Tacks

15
15
15
15
Step 18
Parts Needed - No. 15 QTY 4
No. 15
*Ensure the angled cuts meet
at the top of the apex.
12x40mm Screws
Pre drill
hole
40mm
screw
Pre drill
hole
60mm
bolt
Step 19
Parts needed - No. 19 QTY 8
No. 19
internally
*Ensure the storm braces are
secured at the highest point
possible on each side.
**Storm braces will help your
building expand and contract
properly.
***Important: Ensure each
bolt is tightened using a
washer so as not to damage
the log boards.
16x60mm Bolt Sets
IMPORTANT: Pre-drill before xing screws.
19
19
It is ESSENTIAL that you apply wood
treatment immediately after the building
has been assembled.