Mercia Garden Products OIDTOVRA1006SDFW-V1 User manual







 

 
















  



2mm Drill bit
x2 





























































 
















































¡





 
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Overall Dimensions:
Width = 1842mm
Depth = 1313mm
Height = 2148mm
Base Dimensions:
Width = 1753mm
Depth = 1175mm
2
13 4
6724
8
9
11
12
13
14
15
16
21 22 23
10
29
25 26 27
5
28
Door Panel QTY 1
AI-01R11OVSD1180X1799-V1
Window Panel QTY 1
AI-01R11OV2CW1180X1799-V1
Plain Gable QTY 2
AI-01R11OVAGP1707X2187-V1
Plain Panel 1 QTY 2
AI-R11OVPP1180X1799-V1
Roof QTY 4
PI-03-0247
Floor QTY 2
AI-R11OSBF1753X1456-V1
Door QTY 1
AI-R11FBMBZBD660X1660-V1
Support Block 150x28x28mm QTY 3
F2828-150mm
Ridge Bar 1432x27x70mm QTY 2
F2770-1432mm
Eaves Framing 1502x28x28mm QTY 4
F2828-1502mm
Door Beading Strips 1600x12x28mm QTY 2
S1228-1600mm
Window Cover Trims 518x12x40mm QTY 3
S1240-518mm
Window Cover Trims 1180x12x40mm QTY 1
S1240-1180mm
Cover Trims 1790x12x40mm QTY 8
S1240-1790mm
Fascias 1016x12x60mm QTY 4
S1260-1016mm
Felt QTY 1
PI-01-0015
Styrene QTY 2
PI-05-0114
Corner Brace QTY 2
PI-07-0012
T-Hinge QTY 3
PI-07-0021
Turn Button QTY 2
PI-07-0034
Hasp and Staple QTY 1
PI-07-0207
Window Cill QTY 1
PI-08-0013
Finial QTY 2
Shed diamond Finial
30
Capping Felt QTY 1
PI-01-0020
17 Truss Framing 932x27x44mm QTY 2
F2744-G-972mm
18 Window Strips 544x12x28mm QTY 4
S1228-544mm
Plain Panel 2 QTY 2
AI-R11OVPP560X1799-V1
U Channel QTY 1
PI-07-0013
19 Truss Block 140x27x44mm QTY 2
F2744-G-160mm
20 Truss Support 450x27x44mm QTY 2
F2744-G-490mm
Contents:

¡
 
50mm Screw x 20
Felt Tacks x 85
20mm Screw x 10
30mm Screw x 111
40mm Screw x 20
Nail Bag
There may be extra screws present in the nail bag
Pre Assembly
Before assembling remove the transportation
blocks from the bottom of each panel.
Take care removing the blocks as to not damage
the panels. Tap with a at headed screwdriver
and hammer.
Dispose of the blocks once removed.
7
7
Step 1
Parts Needed- No.7 QTY 1
Place oor (No.7) on rm and level base,
ensure base has suitable drainage free
from areas where water can collect. Attach
the oors using 12x30mm screws
12x30mm Screws
30mm
screw
Pre drill
hole
IMPORTANT: Pre-drill before xing screws.
1
24
24
24
8
Pre drill
hole
30mm
screw
24
Opens from the Left Opens from the Right
IMPORTANT: Pre-drill before xing screws.
Step 2
Parts needed - No. 1 QTY 1
No. 8 QTY 1
No. 24 QTY 3
Place the door (No.8) within the Door
Panel (No. 1). Fix the T Hinges (No. 24)
onto the door and Door Panel as shown
(taking into account on which side of the
Door Panel opening you want the Door
to open).
Ensure that the screws go through the
cladding and into the framing behind.
21x30mm Screws
**PLEASE NOTE** Before tting the
hinges, ensure the door is in the correct
position depending on which side you
want the door to open. See external
illustrations below which show the doors
internal framing.


 
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
50mm
screw
Step 3
Parts Needed- No.3 QTY 1
- No.5 QTY 2
**Please note: the front and back panels
are interchangeable and can be
positioned on either side of the building.
Decide which works best before
assembly**
Place the Plain Gable (No.3) and the Plain
Panel 2 (No.5) onto the oor, secure at the
corners using 3x50mm screws.
Do not secure the building to the oor until
the roof is tted.
Position the panels so there is equal spacing
between the oor and cladding
6x50mm Screws
3
5
a
a
a
a
5
Pre drill
hole
50mm
screw
Step 4
Parts Needed- No.2 QTY 1
- No.4 QTY 1
**Please note: the front and back panels
are interchangeable and can be positioned
on either side of the building.
Place the Window Panel (No.2) onto the oor,
secure to the Plain Panel 2 using 3x50mm
screws in an alternating pattern.
Place the Plain Panel 1 (No.4) and x to the
Plain panel 2 using 3x50mm screws in an
alternating pattern.
Do not secure the building to the oor until
the roof is tted.
Position the panels so there is equal spacing
between the oor and cladding
6x50mm Screws
4
2
a
a
a
a
a
a
IMPORTANT: Pre-drill before xing screws.
4
1
a
a
aa
a
Pre drill
hole
50mm
screw
IMPORTANT: Pre-drill before xing screws.
Step 5
Parts Needed- No.1 QTY 1
- No.4 QTY 1
**Please note: the front and back panels are
interchangeable and can be positioned on
either side of the building.
Place the Door Panel (No.1) onto the oor, secure
to the Window Panel using 3x50mm screws in an
alternating pattern.
Place the Plain Panel 1 (No.4) and x to the Plain
panel 2 using 3x50mm screws in an alternating
pattern.
Do not secure the building to the oor until the
roof is tted.
Position the panels so there is equal spacing
between the oor and cladding
6x50mm Screws
a
3
Step 6
Parts Needed- No.1 QTY 1
Place the Plain Gable (No.3) onto the
oor, secure at the corners using
3x50mm screws per corner.
Do not secure the building to the oor
until the roof is tted.
Position the panels so there is equal
spacing between the oor and
cladding
6x50mm Screws
Pre drill
hole
50mm
screw
a
a
a
a
a
a
IMPORTANT: Pre-drill before xing screws.


 
23
28
10
23
Step 7
Parts Needed- No.10 QTY 2
- No.23 QTY 2
- No.28 QTY 1
Position the two ridge bars (No.10)
within the U channel (No.28) and
secure from either side with 3x30mm
screws and 4x30mm screws from
underneath. Secure a Corner brace
(No.23) to either end of the ridge bar
using 2x30mm screws per bracket.
Place the roof support bar in
between the front and back panels.
Ensure the top corners of the support
bar are ush with each top point.
Secure in place using the L Bracket
on each end with 4x30mm screws.
18x30mm Screws
30mm
screw
Pre drill
hole
10 23
10
IMPORTANT: Pre-drill before xing screws. Step 8
Parts Needed- No.17 QTY 2
Position a truss frame (No.17) to the
ridge bar sloping down towards the
building side, ensure it is central to the
ridge bar with equal distance either
side. Fix with a 50mm screw through
the ridge bar into the truss frame.
Align the second truss frame with the
rst on the opposite side of the ridge
bar and x with a 50mm screw at an
angle as illustrated.
ENSURE SUPPORT BARS ARE
MANUALLY SUPPORTED UNTIL FIXED
AT BOTH ENDS.
4x50mm Screws
ii
Pre drill
hole
50mm
screw
17
17
ab
a
b
IMPORTANT: Pre-drill before xing screws.
Step 9
Parts Needed- No.9 QTY 2
Fix a support block (No.9) on both sides of
the building positioned central to the truss
frame and ush with the underneath of the
panels framing.
Screw through the outside of the building
through the cladding into the panel block
using 2x30mm screw per block.
4x30mm Screws
Pre drill
hole
14
30mm
screw
9
9
9
IMPORTANT: Pre-drill before xing screws.


 
Fix the truss block (No.19) in front
of the support block with 2 x 50mm
screws. Position the block at the top
of the framing with the angle
pointing upwards into the building,
aligning the block centrally along
the join between the side panels
with one screw in each panel.
Fix the truss frame to the block
using 1 x 50mm screw.
Repeat for the other block and
support bar.
6x50mm Screws
ii
i
19
Pre drill
hole
50mm
screw
19
19
Step 10
Parts Needed- No.19 QTY 2
a
b
a
b
IMPORTANT: Pre-drill before xing screws.
Step 11
Parts Needed- No.20 QTY 1
Fix a Truss support (No.20) between
the two truss frames and x in place
using 40mm screws, ensure you
pre-drill holes before xing together.
4x40mm Screws
40mm
screw
Pre drill
hole
20
20
IMPORTANT: Pre-drill before xing screws.
30mm
screw
Pre drill
hole
Step 12
Parts Needed- No.6 QTY 4
- No.11 QTY 4
Fix the Eaves framing (No.11) to the
roof sheets (No.6) using 3x30mm
screws per eaves frame.
The framing should nish ush with
the edge of the roof sheet.
Repeat this method to assemble four
roof sheets.
12x30mm Screws
IMPORTANT: Pre-drill before xing screws.
6
11
6
11
6
11
6
11


 
6
6
6
6
60mm
screw
Pre drill
hole
Step 13
Parts needed - No. 6 QTY 4
Place the Roof Panels (No. 6) on top of the building,
ensuring equal spacing either side of the building
**Make sure that you have got the roof panels the
correct way round with the Eaves Framing to the front
and back of the building.**
From the top, x directly through the roof panels (No. 6)
and into the ridge bar (No. 10) below using 5x30mm
screws per roof panel.
It is essential that the ridge bar (No. 10) and roof panel
(No. 6) framing pull together when xed with 30mm
screws. You may require another person pushing the
ridge bar (No. 10) up from below to achieve this.
Fix the remaining edges of the roof panels using
14x30mm screws, ensuring there is no more than 300mm
between each screw.
24x30mm Screws
IMPORTANT: Pre-drill before xing screws. IMPORTANT: Pre-drill before xing screws.
bb
40mm
screw
Pre drill
hole
Step 14
Fix the building to the oor using
28x40mm screws, ensuring to go
through the panel framing and into the
oor
28x40mm Screws
bbbbbbbbb
b
b
b
bb

¢
 
Pre drill
hole
20mm
screw
Styrene
Window Cill
Cladding
Side View
30mm
screw
a
b
c
d
18
18
18 18
13
13 13
a
b
d
27
27
c
22
SILICONE
SEALANT
Step 15
Parts Needed- No.13 QTY 3
- No.14 QTY 1
- No.18 QTY 4
- No.22 QTY 1
- No.27 QTY 2
14
IMPORTANT: Pre-drill before xing screws.
Fix window strips (No.18) to the framing
along the outside edge of the window gap
using 3x30mm screws per strip.
Place the plastic cill (No.22) into the window
panel as shown in the illustration.
Fit the styrene sheets (No.27) on top of the
window cill.
*For added weather protection t your
windows using silicone sealant around the
outside edges.
**When positioning the styrene sheets
ensure there is an equal distance on all
sides.
Attach the Window Cover Trim (No.13 and
No.14) to either side of the windows and the
centre. Secure into place using 3x30mm
screws per strip.
3x20mm Sxrews
24x30mm Screws
Felt
tacks
Step 16
Parts Needed- No.21 QTY 1
- No.30 QTY 1
Cut the felt (No.21) into 2 sheets
measuring 3050mm (L) x 1000mm (W)
and lay onto roof as shown in diagram.
Cut the Capping Felt (No.30) to 3050mm
(L) x 3000mm (W) and lay on the top of
the roof as shown.
Ensure there is a 50mm overhang around
each side and that each sheet overlaps by
100mm.
Secure in place using felt tacks at 100mm
intervals.
135 x Felt tacks
21
30
100mm
HANDLE
WITH CARE
1 2
3
4
12
3
21
30
21


 
Step 17
Parts Needed- No.15 QTY 8
Fix the cover trims (No.15) to
the corners and the joins of the
building, secure using 3x30mm
for each cover trim
24x30mm Screws
30mm
screw
Pre drill
hole
15 15
15
15
15
IMPORTANT: Pre-drill before xing screws.
Step 18
Parts Needed- No.16 QTY 4
- No.29 QTY 2
Fix the Fascias (No.16) to each side of
the building, secure using 3x30mm
Screws per fascia.
Fix the Diamond Finials (No.29) to
the top of each gable, secure using
2x30mm per Finial, ensuring to go
through the Fascias and into the
plain gable
16x30mm Screws
30mm
screw
Pre drill
hole
16
29
16 29
16
16
IMPORTANT: Pre-drill before xing screws.
Step 19
Parts Needed- No.9 QTY 1
- No.12 QTY 2
Fix the Door Beading strips (No.12)
to the door panel framing, secure
using 4x30mm Screws per strip.
Fix the support block (No.9) onto the
door framing using 2x50mm Screws
8x30mm Screws
2x50mm Screws
30mm
screw
Pre drill
hole
50mm
screw
12
12
12
9
9
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
50mm
screw
Step 20
Parts Needed- No.25 QTY 2
- No.26 QTY 1
Fix the Turn Buttons (No.25) to the door
panel, ensuring that the turn buttons
catch the door, secure using 2x30mm
screws
Fix the Hasp and Staple (No.26) onto
the door and door panel, secure using
7x30mm screws, ensuring the screws
go through the framing
9x30mm Screws
26
26
25
25
25
IMPORTANT: Pre-drill before xing screws.