Messoa NDR891(H) User manual

www.messoa.com
ZEIM-4000827G 2012-07 A1
Outdoor Dome Network Camera
NDR891(H)/NDR891E(H)
Quick Start Guide
Guia de inicio rápido
Guida rapida
Guide de démarrage rapide
Краткое руководство
クイックスタートガイド
快速安裝指南
快速安装指南

NDR891(H)/NDR891E(H) l Quick Start Guide 1
English
Safety Instructions
Make sure the supplied voltage meets the power consumption requirements
of the camera before powering the camera on. Incorrect voltage may cause
damage to the camera.
The camera should be protected from water and moisture, excessive heat,
direct sunlight and cold.
This installation should be made by a qualied service person and should
conform to all local codes.
Unplug the camera during lightening storms or when unused for long
periods of time.
Copyright
No part of this document may be reproduced or transmitted in any form or by
any means, electronic or mechanical, for any purpose, without the express written
permission of MESSOA.
© 2012 All rights reserved.
Disclaimer
Specications and information contained in this document are presented as
accurately as possible as of the time of release, but are not guaranteed to be
entirely free of error. MESSOA assumes no responsibility for errors or omissions
that may appear in this document and reserves the right to change this
publication at any time without obligation to notify anyone of such revisions or
changes.

2 NDR891(H)/NDR891E(H) l Quick Start Guide
1. Introduction
1.1 Package Contents
Outdoor Dome Network Camera x1
CD-ROM (User manual and IP Finder utility) x1
Quick Start Guide x1
Guide Pattern Sticker x1
RJ-45 Female / Female Coupler x1
Accessories
• Tapping Type Flat Head Screw (#1) x3
• Plastic Anchor(#2) x3
• Machine Type Flat Head Screw (#3) x3

NDR891(H)/NDR891E(H) l Quick Start Guide 3
English
1.2 Hardware Overview
Connectors
1
2
3
4
5
6
7
141mm (5.55”)
Ø108mm (4.25”)
121mm (4.76”)
1. Power In (Red+/Black-): Connect to DC 12V/AC 24V (NDR891/NDR891E) or
DC 24V/AC 24V (NDR891H/NDR891EH) power supply. If using the DC power
supply, make sure the power connector is wired to correct polarities (Red+/
Black–). If you are to use power via the PoE connection, this connector is not
used.
2. RJ-45 Ethernet Connector: Network & PoE (Power over Ethernet)
connection. Note that PoE is unable to drive the camera whose heater is
operating.
3. BNC: Composite video output
4. Audio Out (Green): Audio output
5. Audio In (Red): Audio input
6. Alarm Out (Orange): Alarm signal output port
Reserved (Green): Reserved contact
RS-485 (Yellow): Contact for RS-485
7. GND: Ground (electricity) in electrical circuits
Alarm In 1 (Red): Alarm signal input port
Alarm In 2 (Brown): Alarm signal input port

4 NDR891(H)/NDR891E(H) l Quick Start Guide
2. Installation
2.1 Mounting the Camera
This camera is designed for ceiling & wall mounts depending on your
requirements. Mount the camera to your intended location.
Disassembling
1. Take off the dome cover screws.
2. Rotate the dome cover counterclockwise to unlock and pull free of the
housing.
3. Then remove the inner liner by gently pulling it free of the two notches in the
housing.
1. Dome Cover Screws
2. Dome Cover
3. Inner Liner
Tip
Caution
Warning Note
For heater model, the dome cover should NOT be removed over 30 minutes
during installation. Otherwise, the desiccant may absorb too much moisture and
thus cause vapor when the heater is on.

NDR891(H)/NDR891E(H) l Quick Start Guide 5
English
Drilling the Mounting Surface
1. Post the “Guide Pattern” sticker on the mounting surface.
2. Aiming the circles (the gure below marked with “+“ ) on the sticker, drill
three screw holes and one cable entry hole in the ceiling/wall.
+
+
+
+
Mounting the Camera
Use the machine screws to secure the camera base to the surface (this gure take
the tapping type screws as the example to illustrate the mounting).
Guide Pattern Sticker
Tapping Type Screw
Plastic Anchor
Camera Base
TipCautionWarning
Note
1. While you are securing the camera with the accompanying screws, please be
advised to hold the camera by its base. Do not hold the lens or lens base with
force that may deform the lens.
2. Use the machine type screws if you are attaching the camera to a pendent
mounting. Use the tapping type screws for all other surfaces.
3. For cement surfaces, insert the “Plastic Anchors” into the holes. For softer
surfaces, do not use the “Plastic Anchors”.

6 NDR891(H)/NDR891E(H) l Quick Start Guide
Adjusting Camera Angle
Check the monitored view by wiring the RCA jack to a monitor. With an external
monitor connected, you can adjust the camera angle, zoom and focus for
appropriate or better view.
RCA Jack for
Composite Video Output
Pan Adjustment: Rotate the lens base to adjust the horizontal angle.
Tilt Adjustment: Tilt the lens base to adjust the vertical angle.
Tile Angle (max. 70 degrees)
Pan Angle (max. 355 degrees)

NDR891(H)/NDR891E(H) l Quick Start Guide 7
English
Horizontal rotation: Rotate the dome base to adjust the horizontal position. Do
not turn the base more than 355° as this may cause the internal cables to twist
and disconnect or break.
Horizontal Rotation
(max. 355 degrees)
TipCautionWarning
Note
When the tilt angle is less than 75 degrees, there is no distortion.
24° Wide Angle (9mm)
68° Tele Angle (3mm)
70° Tilt Angle
Distortion Area

8 NDR891(H)/NDR891E(H) l Quick Start Guide
Lens Adjustment: Loosen the screws to adjust the zoom control for desired
image view and adjust the focus for optimum picture sharpness. Re-tighten the
screws after nishing zoom/focus adjustments.
Tile (T) & Wide (W)
Near (N) & Far (∞)
Assembling the Camera
1. Assemble the inner liner.
2. If you are to use a microSD/SDHC card, remember to insert the card into the
slot before assembling the dome cover.
3. Assemble the dome cover.
4. Secure the dome cover with the accompanying screw.

NDR891(H)/NDR891E(H) l Quick Start Guide 9
English
2.2. Initial Conguration via a PC
Before connecting the camera to your network infrastructure, it’s suggested that
you connect the camera to a computer rst to perform initial congurations.
1. Configure the computer’s IP address that must be on the same network
segment with the camera’s default IP address (192.168.1.30 by default), such
as:
• IP Address: 192.168.1.100
• Subnet Mask: 255.255.255.0
2. Connect the RJ-45 cable of the camera to the computer.
The LAN port of the camera supports auto MDI/MDIX so there is no need to
use a cross-over cable.
3. To make sure the connection between the camera and the computer is
successful established, you can attempt to ping the camera from your
computer.
• First click the Start menu and select Programs. Then select Accessories.
• Choose Command Prompt. Click OK.
• Type ping x.x.x.x, where x.x.x.x is the IP address of the camera (default
is 192.168.1.30). If the message of “Reply from…” appears, it means the
connection is done.
4. On the PC, launch a web browser and enter the IP address of the camera in
the URL eld:
http://192.168.1.30/
5. When prompted for login, respectively enter the default user name: admin
and password: 1234 to log in. Note that the user name and password are
case-sensitive.
6. Configure the settings to meet your requirements. For more information,
refer to the User Manual on the provided CD-ROM.

10 NDR891(H)/NDR891E(H) l Quick Start Guide
2.3 Connecting to Your Network
Connecting to a LAN
If you have multiple cameras installed on your network, you can use the provided
IP Finder utility to manage the cameras. For more information, refer to the User
Manual on the provided CD-ROM.
Router/Switch/Hub
Connecting to the Internet
Router
xDSL/Cable
Modem
To enable remote access to the cameras, you must congure your router/rewall
to open port numbers. For more information, refer to the User Manual on the
provided CD-ROM.

NDR891(H)/NDR891E(H) l Quick Start Guide 11
English
3 Years Limited Warranty
MESSOA Technologies Inc. (MESSOA) warrants the party that made the original
purchase from MESSOA that the product is free from defects in designs, materials
and workmanship under normal use for a period of 3 (three) years from the date
of the original purchase. For zoom Lens, IR LED light bulbs, and IP Board of IP
speed domes, the warranty period shall be limited to a period of 1 (one) year from
the date of the original purchase. The actual term of warranty will be determined
based upon the product serial number.
Any claim to be made by the original purchase party during the warranty period
shall follow the terms and procedures stated in MESSOA’s 3 Year Warranty Service
Program Agreement. A valid bill of sale must be presented to establish warranty
eligibility. Repaired product following the RMA maintenance procedure will be
warranted for the remainder of its original warranty period.
This Limited Warranty does not apply (i) to damages caused by acts of nature,
abuse, misuse, misapplication, improper interfacing, improper repair, unauthorized
modication, or any operation beyond the design limits, (ii) to software-related
conguration errors, software compatibility and virus, (iii) to consumables and
spare parts, including but not limited to plastic housing and covers, accessories,
and packaging materials.
This Limited Warranty is applicable in all countries. Should the product
malfunction, please contact the party from whom you purchased the product for
assistance.

www.messoa.com
ZEIM-4000827G 2012-07 A1
Cámara de Red Domo para Exteriores
NDR891(H)/NDR891E(H)
Quick Start Guide
Guia de inicio rápido
Guida rapida
Guide de démarrage rapide
Краткое руководство
クイックスタートガイド
快速安裝指南
快速安装指南

NDR891(H)/NDR891E(H) l Guía de inicio rápido 1
Español
Instrucciones de seguridad
Asegúrese de que el voltaje suministrado reúne los requisitos de consumo
energético de la cámara antes de encenderla. Un voltaje incorrecto podría
dañar la cámara.
La cámara debe estar protegida del agua y la humedad, calor excesivo, frío y
luz directa del sol.
La instalación debe ser realizada por personal cualicado de mantenimiento
siguiendo todas las normativas locales.
Desconecta la cámara durante tormentas eléctricas o cuando no vaya a ser
utilizada durante largos periodos de tiempo.
Copyright
Ninguna parte de este documento podrá ser reproducida ni transmitida de
ninguna forma o medio, electrónico mecánico, para ningún propósito, sin el
permiso expreso por escrito de MESSOA.
© 2012 Todos los derechos reservados.
Exención de responsabilidad
Las especicaciones y la información contenidas en este documento se presentan
con la mayor precisión posible cuando fue publicado, pero no se garantiza que
no haya algún error. MESSOA no asume ninguna responsabilidad por los errores
o emisiones que pudieran aparecer en este documento y se reserva el derecho de
modicar el presente en cualquier momento sin la obligación de noticar a nadie
dichas revisiones o modicaciones.

2 NDR891(H)/NDR891E(H) l Guía de inicio rápido
1. Introducción
1.1 Contenidos del paquete
Cámara de Red Domo para Exteriores x1
CD-ROM (Manual de usuario y Utilidad para encontrar la IP) x1
Guía de inicio rápido x1
Pegatina del patrón de guía x1
Acoplador hembra/RJ-45 hembra x1
Accesorios
• Tornillo de cabeza plana tipo enroscante (#1) x3
• Taco de plástico (#2) x3
• Tornillo de cabeza plana tipo máquina (#3) x3

NDR891(H)/NDR891E(H) l Guía de inicio rápido 3
Español
1.2 Presentación del Hardware
Conectores
1
2
3
4
5
6
7
141mm (5.55”)
Ø108mm (4.25”)
121mm (4.76”)
1. Entrada de la fuente de alimentación (Rojo +/Negro -): Conecte a la
fuente de alimentación CC 12V/AC 24V (NDR891/NDR891E) o CC 24V/
AC 24V (NDR891H/NDR891EH). Si va a utilizar la fuente de alimentación
CC, asegúrese de que el conector esté conectado en las polaridades
correctas (Rojo+/Negro-). Si va a utilizar la conexión PoE para suministrar la
electricidad, no se usará este conector.
2. RJ-45 (Ethernet/PoE): Conexión PoE (Power over Ethernet) y de red. Tenga
en cuenta que PoE no puede manejar la cámara que esté operando su
radiador.
3. BNC: Salida de vídeo compuesto
4. Salida de audio (Verde): Salida de audio
5. Entrada de audio (Rojo): Entrada de audio
6. Salida de alarma (Naranja): Puerto de salida de señal de alarma
Reservado (Verde): Contacto reservado
RS-485 (Amarillo): Contacto para RS-485
7. TDT: Toma de tierra (electricidad) de los circuitos eléctricos
Entrada de Alarma 1 (Rojo): Puerto de entrada de señal de alarma
Entrada de Alarma 2 (Marrón): Puerto de entrada de señal de alarma

4 NDR891(H)/NDR891E(H) l Guía de inicio rápido
2. Instalación
2.1 Instalación de la cámara
Esta cámara ha sido diseñada para ser instalada en el techo o en la pared
dependiendo de sus necesidades. Instale la cámara en el lugar deseado.
Desmontaje
1. Extraiga el tornillo de la cubierta domo.
2. Gire la cubierta domo en el sentido contrario a las agujas del reloj para
desbloquearla y extraerla de la carcasa.
3. A continuación, extraiga el alineador interior tirando del mismo para liberar
las dos muescas de la carcasa.
1. Tornillos de la
cubierta domo
2. Cubierta domo
3. Alineador interior
TipPrecauciónWarning Nota
Para el modelo con radiador, la cubierta domo NO debe ser extraida tras 30
minutos durante la instalación. De lo contrario, el desecante podría absorver
demasiada humedad, causando vapor cuando el radiador estuviera encendido.

NDR891(H)/NDR891E(H) l Guía de inicio rápido 5
Español
Taladrado de la supercie de instalación
1. Coloque la pegatina del “Patrón de guía” en la supercie de instalación.
2. Dirija los círculos (la ilustración siguiente marcada con “+”) de la pegatina,
taladre tres oricios para los tornillos y un oricio de entrada del cable en la
pared / techo.
+
+
+
+
Instalación de la cámara
Utilce los tornillos del tipo máquina para asegurar la base de la cámara en la
supercie (esta ilustración toma los tornillos tipo enroscante como ejemplo para
mostrar la instalación).
Pegatina del patrón de
guía
Tornillo tipo enroscante
Taco de plástico
Base de la cámara
TipPrecauciónWarning
Nota
1. Mientras ja la cámara con los tornillos suministrados, se aconseja sostener la
cámara po su base. No sostenga las lentes o la base de las lentes con fuerza
para evitar deformarlas.
2. Utilice los tornillos de tipo máquina si va a jar la cámara en un montaje
colgante. Utilice los tornillos de tipo enroscante para las supercies restantes.
3. Para supercies de cemento, introduzca los “Tacos de plástico” en los oricios.
Para supercies más suaves, no los utilice “Tacos de plástico”.