Wiseup W8200 User manual

W8200
User Guide
I. Product Overview
1. Knob Cover for Mini USB Port
2. Camera Lens
3. Power Button
4. Green/Red Indicator Light
5. Time Adjustment Knob
6. Blue Indicator Light
7. Mode Button
8. Micro SD Card Slot
II. What’s in the Box
-1 × Watch Camera
-1 × USB Cable
-1 × AC110-240V to DC 5V Power Adapter
-1× 8GB Micro SD Card (fitted into the Micro SD card slot already)
III. Operation
>> Before using, please make sure your camera is fully charged.
>> Please make sure the Micro SD card has been formatted already and is securely
fitted into the camera’s SD card slot, or it will not work. We recommend you use a
SDHC Class 10 Micro SD card.
[Note]: If no Micro SD card is fitted into the camera, both blue and green indicator lights will be illumi-
nated for 3 seconds, then the green one will turn off and the blue one will flash 2 seconds and turn off.
After that, the green one will come on and flash 3 times then turn off. The camera will shut down auto-
matically.
3.1. POWER ON/OFF
3.1.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.1.2. Power off the camera by pressing the Power Button for 2 seconds again in
standby mode. The green indicator light will flash 3 times and then turn off together
with the red one.
[Note]: The camera will shut down automatically if it is in standby mode without any operation more
than 3 minutes.
3.2. VIDEO RECORDING
3.2.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.2.2. Press the Power Button once to start video recording. The blue indicator light
will flash 3 times and turn off.
3.2.3. Press the Power Button once again to stop video recording. The blue indicator
light will come on and stay illuminated, indicating the camera is back to standby
mode.
[Note]:
1). A video clip will be generated and saved every 5 minutes automatically.
2). The camera can record video for 120 minutes continuously on a full charge.
3). Each video clip will take up about 380-400MB storage space of the Micro SD card.
4). Video Resolution: 1920x1080P, 1280x720P, 640x480 Optional Video Format: AVI
5). Loop recording is supported.
6). If the battery is low during the video recording process, the green indicator light will flash 15 times
fast then blink 3 times slowly and turn off. Then the camera will save video files then shut down auto-
matically.
3.3. CAMERA/STILL PHOTOGRAPHY
3.3.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.3.2. Press the Mode Button twice to enter into still photograph mode. Both green
and blue indicator lights will stay illuminated.
3.3.3. Press the Power Button once to take a photo. Every time you take a photo,
both green and blue indicator lights will flash once.
3.4. AUDIO RECORDING
3.4.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.4.2. Press the Mode Button once to enter into audio recording mode. The blue
indicator light will turn off while the green indicator light will come on and remain
solid.
3.4.3. Press the Power Button once to record audio only. The green indicator light
will flash 3 times and turn off.
3.4.4. Press the Power Button once again to stop audio recording. The green indica-
tor light will come on and remain solid.
[Note]:
1). An audio clip will be generated and saved every 30 minutes automatically.
2). Audio Format: WAV
IV. Video/Image/Audio File Uploads
4.1. Power off the camera, remove the Micro SD card and insert it into a card reader.
4.2. Insert the card reader into a proper PC computer USB port.
4.3. The camera will be recognized as a removable disk drive.
4.4. All the files can be accessed in the drive.
V. Setting Time/Date Stamp
5.1. Power off the camera, remove the Micro SD card and insert it into a card reader.
5.2. Insert the card reader into a proper PC computer USB port.
5.3. The camera will be recognized as a removable disk drive.
5.4. Click on the drive in the root directory and inside the root directory, open the file
named “time.txt”.
5.5. Write the current date and time in the “time.txt” file with the correct format:
[date]
YYYY-MM-DD HH:MM:SS Y 1
For example:
[date]
2017-04-12 14:24:32 Y 1
Save this file.
5.6. If you need the camera to record video at a lower resolution, you can change 1
into 2 or 3 in the “time.txt” file. 1 stands for 1920x1080P, 2 for 1280x720P and 3 for
640x480.
5.7. If you don’t need the time stamp on the video footage, change “Y” into “N” in the
“time.txt” file.
For example:
[date]
2017-04-12 14:24:32 N 2
5.8. Restart the camera and the system will upgrade the program automatically.
VI. Charging
6.1. Power off the camera and connect the camera to an outlet AC power supply
using the DC5V power adapter and the USB cable provided.
6.2. Both red and blue indicator lights will stay illuminated during the charging pro-
cess.
6.3. It will take 40 minutes to obtain a full charge.
6.4. The red indicator light will turn off and the blue one will stay illuminated when the
camera is fully charged.
VII. Resetting
If for any reason, the camera stops responding or isn’t working properly, a quick
reset will restore it back to normal operation.
Operation: When the camera is powered on, press the Power Button and Mode
Button simultaneously once; the camera will shut down automatically. Then you can
restart the camera with factory default settings.
VIII. Time Setting
8.1. Pull the Time Adjustment Knob until you hear a click. Both hour and minute
hands will be stopped.
8.2. Rotate the Time Adjustment Knob to set time.
8.3. Push the Time Adjustment Knob back after the time set is completed.

I. Product Overview
1. Knob Cover for Mini USB Port
2. Camera Lens
3. Power Button
4. Green/Red Indicator Light
5. Time Adjustment Knob
6. Blue Indicator Light
7. Mode Button
8. Micro SD Card Slot
II. What’s in the Box
-1 × Watch Camera
-1 × USB Cable
-1 × AC110-240V to DC 5V Power Adapter
-1× 8GB Micro SD Card (fitted into the Micro SD card slot already)
III. Operation
>> Before using, please make sure your camera is fully charged.
>> Please make sure the Micro SD card has been formatted already and is securely
fitted into the camera’s SD card slot, or it will not work. We recommend you use a
SDHC Class 10 Micro SD card.
[Note]: If no Micro SD card is fitted into the camera, both blue and green indicator lights will be illumi-
nated for 3 seconds, then the green one will turn off and the blue one will flash 2 seconds and turn off.
After that, the green one will come on and flash 3 times then turn off. The camera will shut down auto-
matically.
3.1. POWER ON/OFF
3.1.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.1.2. Power off the camera by pressing the Power Button for 2 seconds again in
standby mode. The green indicator light will flash 3 times and then turn off together
with the red one.
[Note]: The camera will shut down automatically if it is in standby mode without any operation more
than 3 minutes.
3.2. VIDEO RECORDING
3.2.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.2.2. Press the Power Button once to start video recording. The blue indicator light
will flash 3 times and turn off.
3.2.3. Press the Power Button once again to stop video recording. The blue indicator
light will come on and stay illuminated, indicating the camera is back to standby
mode.
[Note]:
1). A video clip will be generated and saved every 5 minutes automatically.
2). The camera can record video for 120 minutes continuously on a full charge.
3). Each video clip will take up about 380-400MB storage space of the Micro SD card.
4). Video Resolution: 1920x1080P, 1280x720P, 640x480 Optional Video Format: AVI
5). Loop recording is supported.
6). If the battery is low during the video recording process, the green indicator light will flash 15 times
fast then blink 3 times slowly and turn off. Then the camera will save video files then shut down auto-
matically.
3.3. CAMERA/STILL PHOTOGRAPHY
3.3.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.3.2. Press the Mode Button twice to enter into still photograph mode. Both green
and blue indicator lights will stay illuminated.
3.3.3. Press the Power Button once to take a photo. Every time you take a photo,
both green and blue indicator lights will flash once.
3.4. AUDIO RECORDING
3.4.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.4.2. Press the Mode Button once to enter into audio recording mode. The blue
indicator light will turn off while the green indicator light will come on and remain
solid.
3.4.3. Press the Power Button once to record audio only. The green indicator light
will flash 3 times and turn off.
3.4.4. Press the Power Button once again to stop audio recording. The green indica-
tor light will come on and remain solid.
[Note]:
1). An audio clip will be generated and saved every 30 minutes automatically.
2). Audio Format: WAV
IV. Video/Image/Audio File Uploads
4.1. Power off the camera, remove the Micro SD card and insert it into a card reader.
4.2. Insert the card reader into a proper PC computer USB port.
4.3. The camera will be recognized as a removable disk drive.
4.4. All the files can be accessed in the drive.
V. Setting Time/Date Stamp
5.1. Power off the camera, remove the Micro SD card and insert it into a card reader.
5.2. Insert the card reader into a proper PC computer USB port.
5.3. The camera will be recognized as a removable disk drive.
5.4. Click on the drive in the root directory and inside the root directory, open the file
named “time.txt”.
5.5. Write the current date and time in the “time.txt” file with the correct format:
[date]
YYYY-MM-DD HH:MM:SS Y 1
For example:
[date]
2017-04-12 14:24:32 Y 1
Save this file.
5.6. If you need the camera to record video at a lower resolution, you can change 1
into 2 or 3 in the “time.txt” file. 1 stands for 1920x1080P, 2 for 1280x720P and 3 for
640x480.
5.7. If you don’t need the time stamp on the video footage, change “Y” into “N” in the
“time.txt” file.
For example:
[date]
2017-04-12 14:24:32 N 2
5.8. Restart the camera and the system will upgrade the program automatically.
VI. Charging
6.1. Power off the camera and connect the camera to an outlet AC power supply
using the DC5V power adapter and the USB cable provided.
6.2. Both red and blue indicator lights will stay illuminated during the charging pro-
cess.
6.3. It will take 40 minutes to obtain a full charge.
6.4. The red indicator light will turn off and the blue one will stay illuminated when the
camera is fully charged.
VII. Resetting
If for any reason, the camera stops responding or isn’t working properly, a quick
reset will restore it back to normal operation.
Operation: When the camera is powered on, press the Power Button and Mode
Button simultaneously once; the camera will shut down automatically. Then you can
restart the camera with factory default settings.
VIII. Time Setting
8.1. Pull the Time Adjustment Knob until you hear a click. Both hour and minute
hands will be stopped.
8.2. Rotate the Time Adjustment Knob to set time.
8.3. Push the Time Adjustment Knob back after the time set is completed.

I. Product Overview
1. Knob Cover for Mini USB Port
2. Camera Lens
3. Power Button
4. Green/Red Indicator Light
5. Time Adjustment Knob
6. Blue Indicator Light
7. Mode Button
8. Micro SD Card Slot
II. What’s in the Box
-1 × Watch Camera
-1 × USB Cable
-1 × AC110-240V to DC 5V Power Adapter
-1× 8GB Micro SD Card (fitted into the Micro SD card slot already)
III. Operation
>> Before using, please make sure your camera is fully charged.
>> Please make sure the Micro SD card has been formatted already and is securely
fitted into the camera’s SD card slot, or it will not work. We recommend you use a
SDHC Class 10 Micro SD card.
[Note]: If no Micro SD card is fitted into the camera, both blue and green indicator lights will be illumi-
nated for 3 seconds, then the green one will turn off and the blue one will flash 2 seconds and turn off.
After that, the green one will come on and flash 3 times then turn off. The camera will shut down auto-
matically.
3.1. POWER ON/OFF
3.1.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.1.2. Power off the camera by pressing the Power Button for 2 seconds again in
standby mode. The green indicator light will flash 3 times and then turn off together
with the red one.
[Note]: The camera will shut down automatically if it is in standby mode without any operation more
than 3 minutes.
3.2. VIDEO RECORDING
3.2.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.2.2. Press the Power Button once to start video recording. The blue indicator light
will flash 3 times and turn off.
3.2.3. Press the Power Button once again to stop video recording. The blue indicator
light will come on and stay illuminated, indicating the camera is back to standby
mode.
[Note]:
1). A video clip will be generated and saved every 5 minutes automatically.
2). The camera can record video for 120 minutes continuously on a full charge.
3). Each video clip will take up about 380-400MB storage space of the Micro SD card.
4). Video Resolution: 1920x1080P, 1280x720P, 640x480 Optional Video Format: AVI
5). Loop recording is supported.
6). If the battery is low during the video recording process, the green indicator light will flash 15 times
fast then blink 3 times slowly and turn off. Then the camera will save video files then shut down auto-
matically.
3.3. CAMERA/STILL PHOTOGRAPHY
3.3.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.3.2. Press the Mode Button twice to enter into still photograph mode. Both green
and blue indicator lights will stay illuminated.
3.3.3. Press the Power Button once to take a photo. Every time you take a photo,
both green and blue indicator lights will flash once.
3.4. AUDIO RECORDING
3.4.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.4.2. Press the Mode Button once to enter into audio recording mode. The blue
indicator light will turn off while the green indicator light will come on and remain
solid.
3.4.3. Press the Power Button once to record audio only. The green indicator light
will flash 3 times and turn off.
3.4.4. Press the Power Button once again to stop audio recording. The green indica-
tor light will come on and remain solid.
[Note]:
1). An audio clip will be generated and saved every 30 minutes automatically.
2). Audio Format: WAV
IV. Video/Image/Audio File Uploads
4.1. Power off the camera, remove the Micro SD card and insert it into a card reader.
4.2. Insert the card reader into a proper PC computer USB port.
4.3. The camera will be recognized as a removable disk drive.
4.4. All the files can be accessed in the drive.
V. Setting Time/Date Stamp
5.1. Power off the camera, remove the Micro SD card and insert it into a card reader.
5.2. Insert the card reader into a proper PC computer USB port.
5.3. The camera will be recognized as a removable disk drive.
5.4. Click on the drive in the root directory and inside the root directory, open the file
named “time.txt”.
5.5. Write the current date and time in the “time.txt” file with the correct format:
[date]
YYYY-MM-DD HH:MM:SS Y 1
For example:
[date]
2017-04-12 14:24:32 Y 1
Save this file.
5.6. If you need the camera to record video at a lower resolution, you can change 1
into 2 or 3 in the “time.txt” file. 1 stands for 1920x1080P, 2 for 1280x720P and 3 for
640x480.
5.7. If you don’t need the time stamp on the video footage, change “Y” into “N” in the
“time.txt” file.
For example:
[date]
2017-04-12 14:24:32 N 2
5.8. Restart the camera and the system will upgrade the program automatically.
VI. Charging
6.1. Power off the camera and connect the camera to an outlet AC power supply
using the DC5V power adapter and the USB cable provided.
6.2. Both red and blue indicator lights will stay illuminated during the charging pro-
cess.
6.3. It will take 40 minutes to obtain a full charge.
6.4. The red indicator light will turn off and the blue one will stay illuminated when the
camera is fully charged.
VII. Resetting
If for any reason, the camera stops responding or isn’t working properly, a quick
reset will restore it back to normal operation.
Operation: When the camera is powered on, press the Power Button and Mode
Button simultaneously once; the camera will shut down automatically. Then you can
restart the camera with factory default settings.
VIII. Time Setting
8.1. Pull the Time Adjustment Knob until you hear a click. Both hour and minute
hands will be stopped.
8.2. Rotate the Time Adjustment Knob to set time.
8.3. Push the Time Adjustment Knob back after the time set is completed.

I. Product Overview
1. Knob Cover for Mini USB Port
2. Camera Lens
3. Power Button
4. Green/Red Indicator Light
5. Time Adjustment Knob
6. Blue Indicator Light
7. Mode Button
8. Micro SD Card Slot
II. What’s in the Box
-1 × Watch Camera
-1 × USB Cable
-1 × AC110-240V to DC 5V Power Adapter
-1× 8GB Micro SD Card (fitted into the Micro SD card slot already)
III. Operation
>> Before using, please make sure your camera is fully charged.
>> Please make sure the Micro SD card has been formatted already and is securely
fitted into the camera’s SD card slot, or it will not work. We recommend you use a
SDHC Class 10 Micro SD card.
[Note]: If no Micro SD card is fitted into the camera, both blue and green indicator lights will be illumi-
nated for 3 seconds, then the green one will turn off and the blue one will flash 2 seconds and turn off.
After that, the green one will come on and flash 3 times then turn off. The camera will shut down auto-
matically.
3.1. POWER ON/OFF
3.1.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.1.2. Power off the camera by pressing the Power Button for 2 seconds again in
standby mode. The green indicator light will flash 3 times and then turn off together
with the red one.
[Note]: The camera will shut down automatically if it is in standby mode without any operation more
than 3 minutes.
3.2. VIDEO RECORDING
3.2.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.2.2. Press the Power Button once to start video recording. The blue indicator light
will flash 3 times and turn off.
3.2.3. Press the Power Button once again to stop video recording. The blue indicator
light will come on and stay illuminated, indicating the camera is back to standby
mode.
[Note]:
1). A video clip will be generated and saved every 5 minutes automatically.
2). The camera can record video for 120 minutes continuously on a full charge.
3). Each video clip will take up about 380-400MB storage space of the Micro SD card.
4). Video Resolution: 1920x1080P, 1280x720P, 640x480 Optional Video Format: AVI
5). Loop recording is supported.
6). If the battery is low during the video recording process, the green indicator light will flash 15 times
fast then blink 3 times slowly and turn off. Then the camera will save video files then shut down auto-
matically.
3.3. CAMERA/STILL PHOTOGRAPHY
3.3.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.3.2. Press the Mode Button twice to enter into still photograph mode. Both green
and blue indicator lights will stay illuminated.
3.3.3. Press the Power Button once to take a photo. Every time you take a photo,
both green and blue indicator lights will flash once.
3.4. AUDIO RECORDING
3.4.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.4.2. Press the Mode Button once to enter into audio recording mode. The blue
indicator light will turn off while the green indicator light will come on and remain
solid.
3.4.3. Press the Power Button once to record audio only. The green indicator light
will flash 3 times and turn off.
3.4.4. Press the Power Button once again to stop audio recording. The green indica-
tor light will come on and remain solid.
[Note]:
1). An audio clip will be generated and saved every 30 minutes automatically.
2). Audio Format: WAV
IV. Video/Image/Audio File Uploads
4.1. Power off the camera, remove the Micro SD card and insert it into a card reader.
4.2. Insert the card reader into a proper PC computer USB port.
4.3. The camera will be recognized as a removable disk drive.
4.4. All the files can be accessed in the drive.
V. Setting Time/Date Stamp
5.1. Power off the camera, remove the Micro SD card and insert it into a card reader.
5.2. Insert the card reader into a proper PC computer USB port.
5.3. The camera will be recognized as a removable disk drive.
5.4. Click on the drive in the root directory and inside the root directory, open the file
named “time.txt”.
5.5. Write the current date and time in the “time.txt” file with the correct format:
[date]
YYYY-MM-DD HH:MM:SS Y 1
For example:
[date]
2017-04-12 14:24:32 Y 1
Save this file.
5.6. If you need the camera to record video at a lower resolution, you can change 1
into 2 or 3 in the “time.txt” file. 1 stands for 1920x1080P, 2 for 1280x720P and 3 for
640x480.
5.7. If you don’t need the time stamp on the video footage, change “Y” into “N” in the
“time.txt” file.
For example:
[date]
2017-04-12 14:24:32 N 2
5.8. Restart the camera and the system will upgrade the program automatically.
VI. Charging
6.1. Power off the camera and connect the camera to an outlet AC power supply
using the DC5V power adapter and the USB cable provided.
6.2. Both red and blue indicator lights will stay illuminated during the charging pro-
cess.
6.3. It will take 40 minutes to obtain a full charge.
6.4. The red indicator light will turn off and the blue one will stay illuminated when the
camera is fully charged.
VII. Resetting
If for any reason, the camera stops responding or isn’t working properly, a quick
reset will restore it back to normal operation.
Operation: When the camera is powered on, press the Power Button and Mode
Button simultaneously once; the camera will shut down automatically. Then you can
restart the camera with factory default settings.
VIII. Time Setting
8.1. Pull the Time Adjustment Knob until you hear a click. Both hour and minute
hands will be stopped.
8.2. Rotate the Time Adjustment Knob to set time.
8.3. Push the Time Adjustment Knob back after the time set is completed.

I. Product Overview
1. Knob Cover for Mini USB Port
2. Camera Lens
3. Power Button
4. Green/Red Indicator Light
5. Time Adjustment Knob
6. Blue Indicator Light
7. Mode Button
8. Micro SD Card Slot
II. What’s in the Box
-1 × Watch Camera
-1 × USB Cable
-1 × AC110-240V to DC 5V Power Adapter
-1× 8GB Micro SD Card (fitted into the Micro SD card slot already)
III. Operation
>> Before using, please make sure your camera is fully charged.
>> Please make sure the Micro SD card has been formatted already and is securely
fitted into the camera’s SD card slot, or it will not work. We recommend you use a
SDHC Class 10 Micro SD card.
[Note]: If no Micro SD card is fitted into the camera, both blue and green indicator lights will be illumi-
nated for 3 seconds, then the green one will turn off and the blue one will flash 2 seconds and turn off.
After that, the green one will come on and flash 3 times then turn off. The camera will shut down auto-
matically.
3.1. POWER ON/OFF
3.1.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.1.2. Power off the camera by pressing the Power Button for 2 seconds again in
standby mode. The green indicator light will flash 3 times and then turn off together
with the red one.
[Note]: The camera will shut down automatically if it is in standby mode without any operation more
than 3 minutes.
3.2. VIDEO RECORDING
3.2.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.2.2. Press the Power Button once to start video recording. The blue indicator light
will flash 3 times and turn off.
3.2.3. Press the Power Button once again to stop video recording. The blue indicator
light will come on and stay illuminated, indicating the camera is back to standby
mode.
[Note]:
1). A video clip will be generated and saved every 5 minutes automatically.
2). The camera can record video for 120 minutes continuously on a full charge.
3). Each video clip will take up about 380-400MB storage space of the Micro SD card.
4). Video Resolution: 1920x1080P, 1280x720P, 640x480 Optional Video Format: AVI
5). Loop recording is supported.
6). If the battery is low during the video recording process, the green indicator light will flash 15 times
fast then blink 3 times slowly and turn off. Then the camera will save video files then shut down auto-
matically.
3.3. CAMERA/STILL PHOTOGRAPHY
3.3.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.3.2. Press the Mode Button twice to enter into still photograph mode. Both green
and blue indicator lights will stay illuminated.
3.3.3. Press the Power Button once to take a photo. Every time you take a photo,
both green and blue indicator lights will flash once.
3.4. AUDIO RECORDING
3.4.1. Power on the camera by pressing the Power Button for 2 seconds. Both blue
and green indicator lights will be illuminated for 2 seconds and then the green one
will turn off while the blue one will stay illuminated, indicating the camera has en-
tered into standby mode automatically.
3.4.2. Press the Mode Button once to enter into audio recording mode. The blue
indicator light will turn off while the green indicator light will come on and remain
solid.
3.4.3. Press the Power Button once to record audio only. The green indicator light
will flash 3 times and turn off.
3.4.4. Press the Power Button once again to stop audio recording. The green indica-
tor light will come on and remain solid.
[Note]:
1). An audio clip will be generated and saved every 30 minutes automatically.
2). Audio Format: WAV
IV. Video/Image/Audio File Uploads
4.1. Power off the camera, remove the Micro SD card and insert it into a card reader.
4.2. Insert the card reader into a proper PC computer USB port.
4.3. The camera will be recognized as a removable disk drive.
4.4. All the files can be accessed in the drive.
V. Setting Time/Date Stamp
5.1. Power off the camera, remove the Micro SD card and insert it into a card reader.
5.2. Insert the card reader into a proper PC computer USB port.
5.3. The camera will be recognized as a removable disk drive.
5.4. Click on the drive in the root directory and inside the root directory, open the file
named “time.txt”.
5.5. Write the current date and time in the “time.txt” file with the correct format:
[date]
YYYY-MM-DD HH:MM:SS Y 1
For example:
[date]
2017-04-12 14:24:32 Y 1
Save this file.
5.6. If you need the camera to record video at a lower resolution, you can change 1
into 2 or 3 in the “time.txt” file. 1 stands for 1920x1080P, 2 for 1280x720P and 3 for
640x480.
5.7. If you don’t need the time stamp on the video footage, change “Y” into “N” in the
“time.txt” file.
For example:
[date]
2017-04-12 14:24:32 N 2
5.8. Restart the camera and the system will upgrade the program automatically.
VI. Charging
6.1. Power off the camera and connect the camera to an outlet AC power supply
using the DC5V power adapter and the USB cable provided.
6.2. Both red and blue indicator lights will stay illuminated during the charging pro-
cess.
6.3. It will take 40 minutes to obtain a full charge.
6.4. The red indicator light will turn off and the blue one will stay illuminated when the
camera is fully charged.
VII. Resetting
If for any reason, the camera stops responding or isn’t working properly, a quick
reset will restore it back to normal operation.
Operation: When the camera is powered on, press the Power Button and Mode
Button simultaneously once; the camera will shut down automatically. Then you can
restart the camera with factory default settings.
VIII. Time Setting
8.1. Pull the Time Adjustment Knob until you hear a click. Both hour and minute
hands will be stopped.
8.2. Rotate the Time Adjustment Knob to set time.
8.3. Push the Time Adjustment Knob back after the time set is completed.

W8200
Benutzerhandbuch
I. Produktübersicht
1. Knopfabdeckung für Mini-USB-Port
2. Kameraobjektiv
3. Netzschalter
4. Grüne / rote Kontrollleuchte
5. Zeiteinstellknopf
6. Blaues Indikatorlicht
7. Modus-Taste
8. Mikro-Sd-Einbauschlitz
II. Was ist in der Box
-1 × Uhr Kamera anschauen
-1 × USB-Kabel
-1 × AC110-240V bis DC 5V Netzteil
-1 × 8GB Micro SD Card (bereits in den Micro SD Kartensteckplatz eingebaut)
III. Betrieb
>> Vor der Verwendung bitte sicherstellen, dass Ihre Kamera voll aufgeladen ist.
>> Bitte stellen Sie sicher, dass die Micro SD-Karte bereits formatiert ist und sicher
in den SD-Kartensteckplatz der Kamera eingepasst ist, oder es funktioniert nicht.
Wir empfehlen Ihnen, eine SDHC Class 10 Micro SD Karte zu verwenden.
[Hinweis]: Wenn keine Micro SD-Karte in die Kamera eingebaut wird, leuchten die blauen und
grünen Kontrollleuchten für 3 Sekunden, dann wird die grüne ausgeschaltet und die blaue wird 2
Sekunden lang ausschalten und ausschalten. Danach wird die grüne kommen und blinken 3 mal dann
ausschalten. Die Kamera schaltet sich automatisch ab.
3.1. EINSCHALTEN/AUSSCHALTEN
3.1.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.1.2. Schalten Sie die Kamera aus, indem Sie den Netzschalter für 2 Sekunden im
Standby-Modus drücken. Die grüne Kontrollleuchte blinkt dreimal und schaltet sich
dann mit dem roten aus.
[Hinweis]: Die Kamera schaltet sich automatisch aus, wenn sie sich im Standby-Modus befindet,
ohne jeglichen Betrieb mehr als 3 Minuten.
3.2 VIDEOAUFNAHME
3.2.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.2.2. Drücken Sie einmal die Ein- / Aus-Taste, um die Videoaufnahme zu starten.
Die blaue Kontrollleuchte blinkt 3 mal und schaltet sich aus.
3.2.3. Drücken Sie die Power-Taste erneut, um die Videoaufnahme zu stoppen. Die
blaue Kontrollleuchte leuchtet auf und leuchtet auf und zeigt an, dass die Kamera
wieder in den Standby-Modus versetzt wird.
[Hinweis]:
1). Ein Videoclip wird alle 5 Minuten automatisch generiert und gespeichert.
2). Die Kamera kann Video für 120 Minuten kontinuierlich auf eine volle Ladung aufnehmen.
3). Jeder Videoclip nimmt ca. 380-400MB Speicherplatz der Micro SD Karte ein.
4). Video Auflösung: 1920x1080P, 1280x720P, 640x480 Optionales Videoformat: AVI
5). Die Loop-Aufnahme wird unterstützt.
6). Wenn die Batterie während des Videoaufzeichnungsvorgangs niedrig ist, blinkt die grüne Kontroll-
leuchte 15 mal schnell und blinkt dann 3 mal langsam und schaltet sich aus. Dann wird die Kamera
Video-Dateien speichern und dann automatisch herunterfahren.
3.3. KAMERA/NOCH FOTOGRAFIE
3.3.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.3.2. Drücken Sie zweimal die Mode-Taste, um in den Standbildmodus zu gelan-
gen. Beide grüne und blaue Kontrollleuchten bleiben erhalten.
3.3.3. Drücken Sie einmal die Power-Taste, um ein Foto aufzunehmen. Jedes Mal,
wenn Sie ein Foto machen, blinkt die grüne und blaue Kontrollleuchte einmal.
3.4 AUDIO AUFNAHME
3.4.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.4.2. Drücken Sie einmal die Mode-Taste, um in den Audio-Aufnahmemodus zu ge-
langen. Die blaue Kontrollleuchte schaltet sich aus, während die grüne Kontroll-
leuchte aufleuchtet und solide bleibt.
3.4.3. Drücken Sie die Power-Taste einmal, um nur Audio aufzunehmen. Die grüne
Kontrollleuchte blinkt 3 mal und schaltet sich aus.
3.4.4 Drücken Sie erneut die Power-Taste, um die Audioaufnahme zu beenden. Die
grüne Kontrollleuchte leuchtet auf und bleibt solide.
[Hinweis]:
1). Ein Audioclip wird alle 30 Minuten automatisch generiert und gespeichert.
2). Audioformat: WAV
IV. Video/Bild/Audio-Datei Hochgeladen
4.1. Schalten Sie die Kamera aus, entfernen Sie die Micro SD-Karte und legen Sie
sie in einen Kartenleser ein.
4.2. Legen Sie den Kartenleser in einen geeigneten PC-Computer ein.
4.3 Die Kamera wird als Wechseldatenträger erkannt.
4.4 Auf alle Dateien kann im Laufwerk zugegriffen werden.
V. Einstellzeit/Datumsstempel
5.1. Schalten Sie die Kamera aus, entfernen Sie die Micro SD-Karte und legen Sie
sie in einen Kartenleser ein.
5.2. Legen Sie den Kartenleser in einen geeigneten PC-Computer ein.
5.3. Die Kamera wird als Wechseldatenträger erkannt.
5.4 Klicken Sie auf das Laufwerk im Stammverzeichnis und im Stammverzeichnis,
öffnen Sie die Datei mit dem Namen "time.txt".
5.5 Schreiben Sie das aktuelle Datum und die Uhrzeit in der Datei "time.txt" mit dem
richtigen Format:
[date]
JJJJ-MM-TT HH: MM: SS Y 1
Beispielsweise:
[date]
2017-04-12 14:24:32 Y 1
Diese Datei speichern
5.6 Wenn Sie die Kamera benötigen, um Video mit einer niedrigeren Auflösung
aufzunehmen, können Sie 1 in 2 oder 3 in der Datei "time.txt" ändern. 1 steht für
1920x1080P, 2 für 1280x720P und 3 für 640x480.
5.7 Wenn Sie den Zeitstempel auf dem Videomaterial nicht brauchen, ändern Sie
"Y" in "N" in der Datei "time.txt".
Beispielsweise:
[date]
2017-04-12 14:24:32 N 2
5.8 Starten Sie die Kamera neu und das System wird das Programm automatisch
aktualisieren.
VI. Aufladen
6.1. Schalten Sie die Kamera aus und schließen Sie die Kamera an eine Steckdose
an. Netzteil mit dem DC5V Netzteil und dem mitgelieferten USB-Kabel.
6.2. Sowohl die roten als auch die blauen Kontrollleuchten bleiben während des
Ladevorgangs beleuchtet.
6.3. Es dauert 40 Minuten, um eine volle Ladung zu erhalten.
6.4 Die rote Kontrollleuchte schaltet sich aus und die blaue leuchtet auf, wenn die
Kamera voll aufgeladen ist.
VII. Zurücksetzen
Wenn aus irgendeinem Grund die Kamera nicht mehr reagiert oder nicht ordnungs-
gemäß funktioniert, wird ein schneller Reset wieder in den normalen Betrieb zurück-
versetzt.
Bedienung: Wenn die Kamera eingeschaltet ist, drücken Sie gleichzeitig einmal
den Ein- / Ausschalter und die Modus-Taste. Die Kamera schaltet sich automatisch
ab. Dann können Sie die Kamera mit den Werkseinstellungen neu starten.
VIII. Zeiteinstellung
8.1. Ziehen Sie den Zeitregler, bis Sie einen Klick hören. Beide Stunden- und
Minutenzeiger werden gestoppt.
8.2. Drehen Sie den Zeiteinstellknopf, um die Zeit einzustellen.
8.3. Drücken Sie den Zeitregler nach Ablauf der eingestellten Zeit wieder ein.

I. Produktübersicht
1. Knopfabdeckung für Mini-USB-Port
2. Kameraobjektiv
3. Netzschalter
4. Grüne / rote Kontrollleuchte
5. Zeiteinstellknopf
6. Blaues Indikatorlicht
7. Modus-Taste
8. Mikro-Sd-Einbauschlitz
II. Was ist in der Box
-1 × Uhr Kamera anschauen
-1 × USB-Kabel
-1 × AC110-240V bis DC 5V Netzteil
-1 × 8GB Micro SD Card (bereits in den Micro SD Kartensteckplatz eingebaut)
III. Betrieb
>> Vor der Verwendung bitte sicherstellen, dass Ihre Kamera voll aufgeladen ist.
>> Bitte stellen Sie sicher, dass die Micro SD-Karte bereits formatiert ist und sicher
in den SD-Kartensteckplatz der Kamera eingepasst ist, oder es funktioniert nicht.
Wir empfehlen Ihnen, eine SDHC Class 10 Micro SD Karte zu verwenden.
[Hinweis]: Wenn keine Micro SD-Karte in die Kamera eingebaut wird, leuchten die blauen und
grünen Kontrollleuchten für 3 Sekunden, dann wird die grüne ausgeschaltet und die blaue wird 2
Sekunden lang ausschalten und ausschalten. Danach wird die grüne kommen und blinken 3 mal dann
ausschalten. Die Kamera schaltet sich automatisch ab.
3.1. EINSCHALTEN/AUSSCHALTEN
3.1.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.1.2. Schalten Sie die Kamera aus, indem Sie den Netzschalter für 2 Sekunden im
Standby-Modus drücken. Die grüne Kontrollleuchte blinkt dreimal und schaltet sich
dann mit dem roten aus.
[Hinweis]: Die Kamera schaltet sich automatisch aus, wenn sie sich im Standby-Modus befindet,
ohne jeglichen Betrieb mehr als 3 Minuten.
3.2 VIDEOAUFNAHME
3.2.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.2.2. Drücken Sie einmal die Ein- / Aus-Taste, um die Videoaufnahme zu starten.
Die blaue Kontrollleuchte blinkt 3 mal und schaltet sich aus.
3.2.3. Drücken Sie die Power-Taste erneut, um die Videoaufnahme zu stoppen. Die
blaue Kontrollleuchte leuchtet auf und leuchtet auf und zeigt an, dass die Kamera
wieder in den Standby-Modus versetzt wird.
[Hinweis]:
1). Ein Videoclip wird alle 5 Minuten automatisch generiert und gespeichert.
2). Die Kamera kann Video für 120 Minuten kontinuierlich auf eine volle Ladung aufnehmen.
3). Jeder Videoclip nimmt ca. 380-400MB Speicherplatz der Micro SD Karte ein.
4). Video Auflösung: 1920x1080P, 1280x720P, 640x480 Optionales Videoformat: AVI
5). Die Loop-Aufnahme wird unterstützt.
6). Wenn die Batterie während des Videoaufzeichnungsvorgangs niedrig ist, blinkt die grüne Kontroll-
leuchte 15 mal schnell und blinkt dann 3 mal langsam und schaltet sich aus. Dann wird die Kamera
Video-Dateien speichern und dann automatisch herunterfahren.
3.3. KAMERA/NOCH FOTOGRAFIE
3.3.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.3.2. Drücken Sie zweimal die Mode-Taste, um in den Standbildmodus zu gelan-
gen. Beide grüne und blaue Kontrollleuchten bleiben erhalten.
3.3.3. Drücken Sie einmal die Power-Taste, um ein Foto aufzunehmen. Jedes Mal,
wenn Sie ein Foto machen, blinkt die grüne und blaue Kontrollleuchte einmal.
3.4 AUDIO AUFNAHME
3.4.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.4.2. Drücken Sie einmal die Mode-Taste, um in den Audio-Aufnahmemodus zu ge-
langen. Die blaue Kontrollleuchte schaltet sich aus, während die grüne Kontroll-
leuchte aufleuchtet und solide bleibt.
3.4.3. Drücken Sie die Power-Taste einmal, um nur Audio aufzunehmen. Die grüne
Kontrollleuchte blinkt 3 mal und schaltet sich aus.
3.4.4 Drücken Sie erneut die Power-Taste, um die Audioaufnahme zu beenden. Die
grüne Kontrollleuchte leuchtet auf und bleibt solide.
[Hinweis]:
1). Ein Audioclip wird alle 30 Minuten automatisch generiert und gespeichert.
2). Audioformat: WAV
IV. Video/Bild/Audio-Datei Hochgeladen
4.1. Schalten Sie die Kamera aus, entfernen Sie die Micro SD-Karte und legen Sie
sie in einen Kartenleser ein.
4.2. Legen Sie den Kartenleser in einen geeigneten PC-Computer ein.
4.3 Die Kamera wird als Wechseldatenträger erkannt.
4.4 Auf alle Dateien kann im Laufwerk zugegriffen werden.
V. Einstellzeit/Datumsstempel
5.1. Schalten Sie die Kamera aus, entfernen Sie die Micro SD-Karte und legen Sie
sie in einen Kartenleser ein.
5.2. Legen Sie den Kartenleser in einen geeigneten PC-Computer ein.
5.3. Die Kamera wird als Wechseldatenträger erkannt.
5.4 Klicken Sie auf das Laufwerk im Stammverzeichnis und im Stammverzeichnis,
öffnen Sie die Datei mit dem Namen "time.txt".
5.5 Schreiben Sie das aktuelle Datum und die Uhrzeit in der Datei "time.txt" mit dem
richtigen Format:
[date]
JJJJ-MM-TT HH: MM: SS Y 1
Beispielsweise:
[date]
2017-04-12 14:24:32 Y 1
Diese Datei speichern
5.6 Wenn Sie die Kamera benötigen, um Video mit einer niedrigeren Auflösung
aufzunehmen, können Sie 1 in 2 oder 3 in der Datei "time.txt" ändern. 1 steht für
1920x1080P, 2 für 1280x720P und 3 für 640x480.
5.7 Wenn Sie den Zeitstempel auf dem Videomaterial nicht brauchen, ändern Sie
"Y" in "N" in der Datei "time.txt".
Beispielsweise:
[date]
2017-04-12 14:24:32 N 2
5.8 Starten Sie die Kamera neu und das System wird das Programm automatisch
aktualisieren.
VI. Aufladen
6.1. Schalten Sie die Kamera aus und schließen Sie die Kamera an eine Steckdose
an. Netzteil mit dem DC5V Netzteil und dem mitgelieferten USB-Kabel.
6.2. Sowohl die roten als auch die blauen Kontrollleuchten bleiben während des
Ladevorgangs beleuchtet.
6.3. Es dauert 40 Minuten, um eine volle Ladung zu erhalten.
6.4 Die rote Kontrollleuchte schaltet sich aus und die blaue leuchtet auf, wenn die
Kamera voll aufgeladen ist.
VII. Zurücksetzen
Wenn aus irgendeinem Grund die Kamera nicht mehr reagiert oder nicht ordnungs-
gemäß funktioniert, wird ein schneller Reset wieder in den normalen Betrieb zurück-
versetzt.
Bedienung: Wenn die Kamera eingeschaltet ist, drücken Sie gleichzeitig einmal
den Ein- / Ausschalter und die Modus-Taste. Die Kamera schaltet sich automatisch
ab. Dann können Sie die Kamera mit den Werkseinstellungen neu starten.
VIII. Zeiteinstellung
8.1. Ziehen Sie den Zeitregler, bis Sie einen Klick hören. Beide Stunden- und
Minutenzeiger werden gestoppt.
8.2. Drehen Sie den Zeiteinstellknopf, um die Zeit einzustellen.
8.3. Drücken Sie den Zeitregler nach Ablauf der eingestellten Zeit wieder ein.

I. Produktübersicht
1. Knopfabdeckung für Mini-USB-Port
2. Kameraobjektiv
3. Netzschalter
4. Grüne / rote Kontrollleuchte
5. Zeiteinstellknopf
6. Blaues Indikatorlicht
7. Modus-Taste
8. Mikro-Sd-Einbauschlitz
II. Was ist in der Box
-1 × Uhr Kamera anschauen
-1 × USB-Kabel
-1 × AC110-240V bis DC 5V Netzteil
-1 × 8GB Micro SD Card (bereits in den Micro SD Kartensteckplatz eingebaut)
III. Betrieb
>> Vor der Verwendung bitte sicherstellen, dass Ihre Kamera voll aufgeladen ist.
>> Bitte stellen Sie sicher, dass die Micro SD-Karte bereits formatiert ist und sicher
in den SD-Kartensteckplatz der Kamera eingepasst ist, oder es funktioniert nicht.
Wir empfehlen Ihnen, eine SDHC Class 10 Micro SD Karte zu verwenden.
[Hinweis]: Wenn keine Micro SD-Karte in die Kamera eingebaut wird, leuchten die blauen und
grünen Kontrollleuchten für 3 Sekunden, dann wird die grüne ausgeschaltet und die blaue wird 2
Sekunden lang ausschalten und ausschalten. Danach wird die grüne kommen und blinken 3 mal dann
ausschalten. Die Kamera schaltet sich automatisch ab.
3.1. EINSCHALTEN/AUSSCHALTEN
3.1.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.1.2. Schalten Sie die Kamera aus, indem Sie den Netzschalter für 2 Sekunden im
Standby-Modus drücken. Die grüne Kontrollleuchte blinkt dreimal und schaltet sich
dann mit dem roten aus.
[Hinweis]: Die Kamera schaltet sich automatisch aus, wenn sie sich im Standby-Modus befindet,
ohne jeglichen Betrieb mehr als 3 Minuten.
3.2 VIDEOAUFNAHME
3.2.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.2.2. Drücken Sie einmal die Ein- / Aus-Taste, um die Videoaufnahme zu starten.
Die blaue Kontrollleuchte blinkt 3 mal und schaltet sich aus.
3.2.3. Drücken Sie die Power-Taste erneut, um die Videoaufnahme zu stoppen. Die
blaue Kontrollleuchte leuchtet auf und leuchtet auf und zeigt an, dass die Kamera
wieder in den Standby-Modus versetzt wird.
[Hinweis]:
1). Ein Videoclip wird alle 5 Minuten automatisch generiert und gespeichert.
2). Die Kamera kann Video für 120 Minuten kontinuierlich auf eine volle Ladung aufnehmen.
3). Jeder Videoclip nimmt ca. 380-400MB Speicherplatz der Micro SD Karte ein.
4). Video Auflösung: 1920x1080P, 1280x720P, 640x480 Optionales Videoformat: AVI
5). Die Loop-Aufnahme wird unterstützt.
6). Wenn die Batterie während des Videoaufzeichnungsvorgangs niedrig ist, blinkt die grüne Kontroll-
leuchte 15 mal schnell und blinkt dann 3 mal langsam und schaltet sich aus. Dann wird die Kamera
Video-Dateien speichern und dann automatisch herunterfahren.
3.3. KAMERA/NOCH FOTOGRAFIE
3.3.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.3.2. Drücken Sie zweimal die Mode-Taste, um in den Standbildmodus zu gelan-
gen. Beide grüne und blaue Kontrollleuchten bleiben erhalten.
3.3.3. Drücken Sie einmal die Power-Taste, um ein Foto aufzunehmen. Jedes Mal,
wenn Sie ein Foto machen, blinkt die grüne und blaue Kontrollleuchte einmal.
3.4 AUDIO AUFNAHME
3.4.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.4.2. Drücken Sie einmal die Mode-Taste, um in den Audio-Aufnahmemodus zu ge-
langen. Die blaue Kontrollleuchte schaltet sich aus, während die grüne Kontroll-
leuchte aufleuchtet und solide bleibt.
3.4.3. Drücken Sie die Power-Taste einmal, um nur Audio aufzunehmen. Die grüne
Kontrollleuchte blinkt 3 mal und schaltet sich aus.
3.4.4 Drücken Sie erneut die Power-Taste, um die Audioaufnahme zu beenden. Die
grüne Kontrollleuchte leuchtet auf und bleibt solide.
[Hinweis]:
1). Ein Audioclip wird alle 30 Minuten automatisch generiert und gespeichert.
2). Audioformat: WAV
IV. Video/Bild/Audio-Datei Hochgeladen
4.1. Schalten Sie die Kamera aus, entfernen Sie die Micro SD-Karte und legen Sie
sie in einen Kartenleser ein.
4.2. Legen Sie den Kartenleser in einen geeigneten PC-Computer ein.
4.3 Die Kamera wird als Wechseldatenträger erkannt.
4.4 Auf alle Dateien kann im Laufwerk zugegriffen werden.
V. Einstellzeit/Datumsstempel
5.1. Schalten Sie die Kamera aus, entfernen Sie die Micro SD-Karte und legen Sie
sie in einen Kartenleser ein.
5.2. Legen Sie den Kartenleser in einen geeigneten PC-Computer ein.
5.3. Die Kamera wird als Wechseldatenträger erkannt.
5.4 Klicken Sie auf das Laufwerk im Stammverzeichnis und im Stammverzeichnis,
öffnen Sie die Datei mit dem Namen "time.txt".
5.5 Schreiben Sie das aktuelle Datum und die Uhrzeit in der Datei "time.txt" mit dem
richtigen Format:
[date]
JJJJ-MM-TT HH: MM: SS Y 1
Beispielsweise:
[date]
2017-04-12 14:24:32 Y 1
Diese Datei speichern
5.6 Wenn Sie die Kamera benötigen, um Video mit einer niedrigeren Auflösung
aufzunehmen, können Sie 1 in 2 oder 3 in der Datei "time.txt" ändern. 1 steht für
1920x1080P, 2 für 1280x720P und 3 für 640x480.
5.7 Wenn Sie den Zeitstempel auf dem Videomaterial nicht brauchen, ändern Sie
"Y" in "N" in der Datei "time.txt".
Beispielsweise:
[date]
2017-04-12 14:24:32 N 2
5.8 Starten Sie die Kamera neu und das System wird das Programm automatisch
aktualisieren.
VI. Aufladen
6.1. Schalten Sie die Kamera aus und schließen Sie die Kamera an eine Steckdose
an. Netzteil mit dem DC5V Netzteil und dem mitgelieferten USB-Kabel.
6.2. Sowohl die roten als auch die blauen Kontrollleuchten bleiben während des
Ladevorgangs beleuchtet.
6.3. Es dauert 40 Minuten, um eine volle Ladung zu erhalten.
6.4 Die rote Kontrollleuchte schaltet sich aus und die blaue leuchtet auf, wenn die
Kamera voll aufgeladen ist.
VII. Zurücksetzen
Wenn aus irgendeinem Grund die Kamera nicht mehr reagiert oder nicht ordnungs-
gemäß funktioniert, wird ein schneller Reset wieder in den normalen Betrieb zurück-
versetzt.
Bedienung: Wenn die Kamera eingeschaltet ist, drücken Sie gleichzeitig einmal
den Ein- / Ausschalter und die Modus-Taste. Die Kamera schaltet sich automatisch
ab. Dann können Sie die Kamera mit den Werkseinstellungen neu starten.
VIII. Zeiteinstellung
8.1. Ziehen Sie den Zeitregler, bis Sie einen Klick hören. Beide Stunden- und
Minutenzeiger werden gestoppt.
8.2. Drehen Sie den Zeiteinstellknopf, um die Zeit einzustellen.
8.3. Drücken Sie den Zeitregler nach Ablauf der eingestellten Zeit wieder ein.

I. Produktübersicht
1. Knopfabdeckung für Mini-USB-Port
2. Kameraobjektiv
3. Netzschalter
4. Grüne / rote Kontrollleuchte
5. Zeiteinstellknopf
6. Blaues Indikatorlicht
7. Modus-Taste
8. Mikro-Sd-Einbauschlitz
II. Was ist in der Box
-1 × Uhr Kamera anschauen
-1 × USB-Kabel
-1 × AC110-240V bis DC 5V Netzteil
-1 × 8GB Micro SD Card (bereits in den Micro SD Kartensteckplatz eingebaut)
III. Betrieb
>> Vor der Verwendung bitte sicherstellen, dass Ihre Kamera voll aufgeladen ist.
>> Bitte stellen Sie sicher, dass die Micro SD-Karte bereits formatiert ist und sicher
in den SD-Kartensteckplatz der Kamera eingepasst ist, oder es funktioniert nicht.
Wir empfehlen Ihnen, eine SDHC Class 10 Micro SD Karte zu verwenden.
[Hinweis]: Wenn keine Micro SD-Karte in die Kamera eingebaut wird, leuchten die blauen und
grünen Kontrollleuchten für 3 Sekunden, dann wird die grüne ausgeschaltet und die blaue wird 2
Sekunden lang ausschalten und ausschalten. Danach wird die grüne kommen und blinken 3 mal dann
ausschalten. Die Kamera schaltet sich automatisch ab.
3.1. EINSCHALTEN/AUSSCHALTEN
3.1.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.1.2. Schalten Sie die Kamera aus, indem Sie den Netzschalter für 2 Sekunden im
Standby-Modus drücken. Die grüne Kontrollleuchte blinkt dreimal und schaltet sich
dann mit dem roten aus.
[Hinweis]: Die Kamera schaltet sich automatisch aus, wenn sie sich im Standby-Modus befindet,
ohne jeglichen Betrieb mehr als 3 Minuten.
3.2 VIDEOAUFNAHME
3.2.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.2.2. Drücken Sie einmal die Ein- / Aus-Taste, um die Videoaufnahme zu starten.
Die blaue Kontrollleuchte blinkt 3 mal und schaltet sich aus.
3.2.3. Drücken Sie die Power-Taste erneut, um die Videoaufnahme zu stoppen. Die
blaue Kontrollleuchte leuchtet auf und leuchtet auf und zeigt an, dass die Kamera
wieder in den Standby-Modus versetzt wird.
[Hinweis]:
1). Ein Videoclip wird alle 5 Minuten automatisch generiert und gespeichert.
2). Die Kamera kann Video für 120 Minuten kontinuierlich auf eine volle Ladung aufnehmen.
3). Jeder Videoclip nimmt ca. 380-400MB Speicherplatz der Micro SD Karte ein.
4). Video Auflösung: 1920x1080P, 1280x720P, 640x480 Optionales Videoformat: AVI
5). Die Loop-Aufnahme wird unterstützt.
6). Wenn die Batterie während des Videoaufzeichnungsvorgangs niedrig ist, blinkt die grüne Kontroll-
leuchte 15 mal schnell und blinkt dann 3 mal langsam und schaltet sich aus. Dann wird die Kamera
Video-Dateien speichern und dann automatisch herunterfahren.
3.3. KAMERA/NOCH FOTOGRAFIE
3.3.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.3.2. Drücken Sie zweimal die Mode-Taste, um in den Standbildmodus zu gelan-
gen. Beide grüne und blaue Kontrollleuchten bleiben erhalten.
3.3.3. Drücken Sie einmal die Power-Taste, um ein Foto aufzunehmen. Jedes Mal,
wenn Sie ein Foto machen, blinkt die grüne und blaue Kontrollleuchte einmal.
3.4 AUDIO AUFNAHME
3.4.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.4.2. Drücken Sie einmal die Mode-Taste, um in den Audio-Aufnahmemodus zu ge-
langen. Die blaue Kontrollleuchte schaltet sich aus, während die grüne Kontroll-
leuchte aufleuchtet und solide bleibt.
3.4.3. Drücken Sie die Power-Taste einmal, um nur Audio aufzunehmen. Die grüne
Kontrollleuchte blinkt 3 mal und schaltet sich aus.
3.4.4 Drücken Sie erneut die Power-Taste, um die Audioaufnahme zu beenden. Die
grüne Kontrollleuchte leuchtet auf und bleibt solide.
[Hinweis]:
1). Ein Audioclip wird alle 30 Minuten automatisch generiert und gespeichert.
2). Audioformat: WAV
IV. Video/Bild/Audio-Datei Hochgeladen
4.1. Schalten Sie die Kamera aus, entfernen Sie die Micro SD-Karte und legen Sie
sie in einen Kartenleser ein.
4.2. Legen Sie den Kartenleser in einen geeigneten PC-Computer ein.
4.3 Die Kamera wird als Wechseldatenträger erkannt.
4.4 Auf alle Dateien kann im Laufwerk zugegriffen werden.
V. Einstellzeit/Datumsstempel
5.1. Schalten Sie die Kamera aus, entfernen Sie die Micro SD-Karte und legen Sie
sie in einen Kartenleser ein.
5.2. Legen Sie den Kartenleser in einen geeigneten PC-Computer ein.
5.3. Die Kamera wird als Wechseldatenträger erkannt.
5.4 Klicken Sie auf das Laufwerk im Stammverzeichnis und im Stammverzeichnis,
öffnen Sie die Datei mit dem Namen "time.txt".
5.5 Schreiben Sie das aktuelle Datum und die Uhrzeit in der Datei "time.txt" mit dem
richtigen Format:
[date]
JJJJ-MM-TT HH: MM: SS Y 1
Beispielsweise:
[date]
2017-04-12 14:24:32 Y 1
Diese Datei speichern
5.6 Wenn Sie die Kamera benötigen, um Video mit einer niedrigeren Auflösung
aufzunehmen, können Sie 1 in 2 oder 3 in der Datei "time.txt" ändern. 1 steht für
1920x1080P, 2 für 1280x720P und 3 für 640x480.
5.7 Wenn Sie den Zeitstempel auf dem Videomaterial nicht brauchen, ändern Sie
"Y" in "N" in der Datei "time.txt".
Beispielsweise:
[date]
2017-04-12 14:24:32 N 2
5.8 Starten Sie die Kamera neu und das System wird das Programm automatisch
aktualisieren.
VI. Aufladen
6.1. Schalten Sie die Kamera aus und schließen Sie die Kamera an eine Steckdose
an. Netzteil mit dem DC5V Netzteil und dem mitgelieferten USB-Kabel.
6.2. Sowohl die roten als auch die blauen Kontrollleuchten bleiben während des
Ladevorgangs beleuchtet.
6.3. Es dauert 40 Minuten, um eine volle Ladung zu erhalten.
6.4 Die rote Kontrollleuchte schaltet sich aus und die blaue leuchtet auf, wenn die
Kamera voll aufgeladen ist.
VII. Zurücksetzen
Wenn aus irgendeinem Grund die Kamera nicht mehr reagiert oder nicht ordnungs-
gemäß funktioniert, wird ein schneller Reset wieder in den normalen Betrieb zurück-
versetzt.
Bedienung: Wenn die Kamera eingeschaltet ist, drücken Sie gleichzeitig einmal
den Ein- / Ausschalter und die Modus-Taste. Die Kamera schaltet sich automatisch
ab. Dann können Sie die Kamera mit den Werkseinstellungen neu starten.
VIII. Zeiteinstellung
8.1. Ziehen Sie den Zeitregler, bis Sie einen Klick hören. Beide Stunden- und
Minutenzeiger werden gestoppt.
8.2. Drehen Sie den Zeiteinstellknopf, um die Zeit einzustellen.
8.3. Drücken Sie den Zeitregler nach Ablauf der eingestellten Zeit wieder ein.

I. Produktübersicht
1. Knopfabdeckung für Mini-USB-Port
2. Kameraobjektiv
3. Netzschalter
4. Grüne / rote Kontrollleuchte
5. Zeiteinstellknopf
6. Blaues Indikatorlicht
7. Modus-Taste
8. Mikro-Sd-Einbauschlitz
II. Was ist in der Box
-1 × Uhr Kamera anschauen
-1 × USB-Kabel
-1 × AC110-240V bis DC 5V Netzteil
-1 × 8GB Micro SD Card (bereits in den Micro SD Kartensteckplatz eingebaut)
III. Betrieb
>> Vor der Verwendung bitte sicherstellen, dass Ihre Kamera voll aufgeladen ist.
>> Bitte stellen Sie sicher, dass die Micro SD-Karte bereits formatiert ist und sicher
in den SD-Kartensteckplatz der Kamera eingepasst ist, oder es funktioniert nicht.
Wir empfehlen Ihnen, eine SDHC Class 10 Micro SD Karte zu verwenden.
[Hinweis]: Wenn keine Micro SD-Karte in die Kamera eingebaut wird, leuchten die blauen und
grünen Kontrollleuchten für 3 Sekunden, dann wird die grüne ausgeschaltet und die blaue wird 2
Sekunden lang ausschalten und ausschalten. Danach wird die grüne kommen und blinken 3 mal dann
ausschalten. Die Kamera schaltet sich automatisch ab.
3.1. EINSCHALTEN/AUSSCHALTEN
3.1.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.1.2. Schalten Sie die Kamera aus, indem Sie den Netzschalter für 2 Sekunden im
Standby-Modus drücken. Die grüne Kontrollleuchte blinkt dreimal und schaltet sich
dann mit dem roten aus.
[Hinweis]: Die Kamera schaltet sich automatisch aus, wenn sie sich im Standby-Modus befindet,
ohne jeglichen Betrieb mehr als 3 Minuten.
3.2 VIDEOAUFNAHME
3.2.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.2.2. Drücken Sie einmal die Ein- / Aus-Taste, um die Videoaufnahme zu starten.
Die blaue Kontrollleuchte blinkt 3 mal und schaltet sich aus.
3.2.3. Drücken Sie die Power-Taste erneut, um die Videoaufnahme zu stoppen. Die
blaue Kontrollleuchte leuchtet auf und leuchtet auf und zeigt an, dass die Kamera
wieder in den Standby-Modus versetzt wird.
[Hinweis]:
1). Ein Videoclip wird alle 5 Minuten automatisch generiert und gespeichert.
2). Die Kamera kann Video für 120 Minuten kontinuierlich auf eine volle Ladung aufnehmen.
3). Jeder Videoclip nimmt ca. 380-400MB Speicherplatz der Micro SD Karte ein.
4). Video Auflösung: 1920x1080P, 1280x720P, 640x480 Optionales Videoformat: AVI
5). Die Loop-Aufnahme wird unterstützt.
6). Wenn die Batterie während des Videoaufzeichnungsvorgangs niedrig ist, blinkt die grüne Kontroll-
leuchte 15 mal schnell und blinkt dann 3 mal langsam und schaltet sich aus. Dann wird die Kamera
Video-Dateien speichern und dann automatisch herunterfahren.
3.3. KAMERA/NOCH FOTOGRAFIE
3.3.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.3.2. Drücken Sie zweimal die Mode-Taste, um in den Standbildmodus zu gelan-
gen. Beide grüne und blaue Kontrollleuchten bleiben erhalten.
3.3.3. Drücken Sie einmal die Power-Taste, um ein Foto aufzunehmen. Jedes Mal,
wenn Sie ein Foto machen, blinkt die grüne und blaue Kontrollleuchte einmal.
3.4 AUDIO AUFNAHME
3.4.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter 2 Sekunden lang
drücken. Die blauen und grünen Kontrollleuchten werden für 2 Sekunden beleuchtet
und dann wird die grüne ausgeschaltet, während die blaue beleuchtet bleibt, was
anzeigt, dass die Kamera automatisch in den Standby-Modus geschaltet ist.
3.4.2. Drücken Sie einmal die Mode-Taste, um in den Audio-Aufnahmemodus zu ge-
langen. Die blaue Kontrollleuchte schaltet sich aus, während die grüne Kontroll-
leuchte aufleuchtet und solide bleibt.
3.4.3. Drücken Sie die Power-Taste einmal, um nur Audio aufzunehmen. Die grüne
Kontrollleuchte blinkt 3 mal und schaltet sich aus.
3.4.4 Drücken Sie erneut die Power-Taste, um die Audioaufnahme zu beenden. Die
grüne Kontrollleuchte leuchtet auf und bleibt solide.
[Hinweis]:
1). Ein Audioclip wird alle 30 Minuten automatisch generiert und gespeichert.
2). Audioformat: WAV
IV. Video/Bild/Audio-Datei Hochgeladen
4.1. Schalten Sie die Kamera aus, entfernen Sie die Micro SD-Karte und legen Sie
sie in einen Kartenleser ein.
4.2. Legen Sie den Kartenleser in einen geeigneten PC-Computer ein.
4.3 Die Kamera wird als Wechseldatenträger erkannt.
4.4 Auf alle Dateien kann im Laufwerk zugegriffen werden.
V. Einstellzeit/Datumsstempel
5.1. Schalten Sie die Kamera aus, entfernen Sie die Micro SD-Karte und legen Sie
sie in einen Kartenleser ein.
5.2. Legen Sie den Kartenleser in einen geeigneten PC-Computer ein.
5.3. Die Kamera wird als Wechseldatenträger erkannt.
5.4 Klicken Sie auf das Laufwerk im Stammverzeichnis und im Stammverzeichnis,
öffnen Sie die Datei mit dem Namen "time.txt".
5.5 Schreiben Sie das aktuelle Datum und die Uhrzeit in der Datei "time.txt" mit dem
richtigen Format:
[date]
JJJJ-MM-TT HH: MM: SS Y 1
Beispielsweise:
[date]
2017-04-12 14:24:32 Y 1
Diese Datei speichern
5.6 Wenn Sie die Kamera benötigen, um Video mit einer niedrigeren Auflösung
aufzunehmen, können Sie 1 in 2 oder 3 in der Datei "time.txt" ändern. 1 steht für
1920x1080P, 2 für 1280x720P und 3 für 640x480.
5.7 Wenn Sie den Zeitstempel auf dem Videomaterial nicht brauchen, ändern Sie
"Y" in "N" in der Datei "time.txt".
Beispielsweise:
[date]
2017-04-12 14:24:32 N 2
5.8 Starten Sie die Kamera neu und das System wird das Programm automatisch
aktualisieren.
VI. Aufladen
6.1. Schalten Sie die Kamera aus und schließen Sie die Kamera an eine Steckdose
an. Netzteil mit dem DC5V Netzteil und dem mitgelieferten USB-Kabel.
6.2. Sowohl die roten als auch die blauen Kontrollleuchten bleiben während des
Ladevorgangs beleuchtet.
6.3. Es dauert 40 Minuten, um eine volle Ladung zu erhalten.
6.4 Die rote Kontrollleuchte schaltet sich aus und die blaue leuchtet auf, wenn die
Kamera voll aufgeladen ist.
VII. Zurücksetzen
Wenn aus irgendeinem Grund die Kamera nicht mehr reagiert oder nicht ordnungs-
gemäß funktioniert, wird ein schneller Reset wieder in den normalen Betrieb zurück-
versetzt.
Bedienung: Wenn die Kamera eingeschaltet ist, drücken Sie gleichzeitig einmal
den Ein- / Ausschalter und die Modus-Taste. Die Kamera schaltet sich automatisch
ab. Dann können Sie die Kamera mit den Werkseinstellungen neu starten.
VIII. Zeiteinstellung
8.1. Ziehen Sie den Zeitregler, bis Sie einen Klick hören. Beide Stunden- und
Minutenzeiger werden gestoppt.
8.2. Drehen Sie den Zeiteinstellknopf, um die Zeit einzustellen.
8.3. Drücken Sie den Zeitregler nach Ablauf der eingestellten Zeit wieder ein.

W8200
Mode d'emploi
I. Vue d'ensemble du produit
1. Couvercle de bouton pour mini port USB
2. Lentille de caméra
3. Bouton d’Alimentation
4. Voyant Vert / Rouge
5. Bouton de Réglage du Temps
6. Voyant Bleu
7. Bouton Mode
8. Emplacement pour Carte Micro SD
II. Qu'y a-t-il dans la Boite
-1 × Caméra Montre
-1 × Câble USB
-1 × AC110-240V à DC 5V adaptateur secteur
-1 × 8 GB de carte Micro SD (monté sur l'emplacement de la carte Micro SD déjà)
III. Opération
>> Avant d'utiliser, assurez-vous que votre appareil photo est complètement chargé.
>> Assurez-vous que la carte Micro SD a déjà été formatée et qu'elle est correcte-
ment installée dans la fente de la carte SD de la caméra, ou elle ne fonctionnera
pas. Nous vous recommandons d'utiliser une carte SD SDHC de classe 10 SD.
[Note]: Si aucune carte Micro SD n'est installée dans la caméra, les voyants lumineux bleu et vert
s'allument pendant 3 secondes, puis le vert s'éteint et le bleu clignotera 2 secondes et s'éteindra. Après
cela, le vert s'allume et clignote 3 fois puis éteint. La caméra s'arrête automatiquement.
3.1. MARCHE/ARRÊT
3.1.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.1.2. Mettez l'appareil hors tension en appuyant de nouveau sur le Bouton d’Ali-
mentation pendant 2 secondes en mode veille. Le voyant vert clignote 3 fois, puis
éteint avec le rouge.
[Note]: La caméra s'arrête automatiquement s'il est en mode veille sans aucune opération pendant
plus de 3 minutes.
3.2. ENREGISTREMENT VIDEO
3.2.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.2.2. Appuyez une fois sur le Bouton d’Alimentation pour commencer l'enregis-
trement vidéo. Le voyant bleu clignote 3 fois et éteint.
3.2.3 Appuyez à nouveau sur le Bouton d’Alimentation pour arrêter l'enregistrement
vidéo. Le voyant bleu s'allume et reste allumé, indiquant que la caméra est en mode
veille.
[Note]:
1). Un clip vidéo sera généré et enregistré toutes les 5 minutes automatiquement.
2). La caméra peut enregistrer une vidéo pendant 120 minutes en continu sur une charge complète.
3). Chaque vidéo prendra environ 380-400 Mo d'espace de stockage de la carte Micro SD.
4). Résolution vidéo optionnel: 1920x1080P, 1280x720P, 640x480 Format vidéo: AVI
5). L'enregistrement en boucle est pris en charge.
6). Si la batterie est faible pendant le processus d'enregistrement vidéo, le voyant vert clignote 15 fois
rapidement, puis clignote 3 fois lentement et éteignez. Ensuite, la caméra enregistre les fichiers vidéo
puis s'éteint automatiquement.
3.3. CAMERA/STILL PHOTOGRAPHIE
3.3.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.3.2. Appuyez deux fois sur le bouton Mode pour entrer en mode photographie fixe.
Les voyants lumineux vert et bleu resteront allumés.
3.3.3. Appuyez une fois sur le Bouton d’Alimentation pour prendre une photo.
Chaque fois que vous prenez une photo, les voyants lumineux vert et bleu clignotent
une fois.
3.4. ENREGISTREMENT AUDIO
3.4.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.4.2. Appuyez une fois sur le bouton Mode pour entrer en mode d'enregistrement
audio. Le témoin lumineux bleu s'éteint lorsque le voyant vert s'allume et reste
solide.
3.4.3. Appuyez une fois sur le Bouton d’Alimentation pour enregistrer uniquement
l'audio. Le voyant vert clignote 3 fois et éteint.
3.4.4. Appuyez à nouveau sur le Bouton d’Alimentation pour arrêter l'enregistrement
audio. Le voyant vert s'allume et reste solide.
[Note]:
1). Un clip audio sera généré et sauvegardé toutes les 30 minutes automatiquement.
2). Format audio: WAV
IV. Téléchargement de Fichiers Vidéo/Image/Audio
4.1. Éteignez la caméra, retirez la carte Micro SD et insérez-la dans un lecteur de
carte.
4.2. Insérez le lecteur de carte dans un port USB approprié pour PC.
4.3. La caméra sera reconnu comme un lecteur de disque amovible.
4.4. Tous les fichiers peuvent être consultés dans le lecteur.
V. Réglage de l'heure/Date Stamp
5.1. Éteignez la caméra, retirez la carte Micro SD et insérez-la dans un lecteur de
carte.
5.2. Insérez le lecteur de carte dans un port USB approprié pour PC.
5.3. La caméra sera reconnu comme un lecteur de disque amovible.
5.4. Cliquez sur le lecteur dans le répertoire racine et dans le répertoire racine,
ouvrez le fichier nommé "time.txt".
5.5. Écrivez la date et l'heure actuelles dans le fichier "time.txt" avec le format cor-
rect:
[date]
AAAA-MM-DD HH: MM: SS Y 1
Par exemple:
[date]
2017-04-12 14:24:32 Y 1
Enregistrez ce fichier.
5.6. Si vous avez besoin de la caméra pour enregistrer une vidéo à une résolution
inférieure, vous pouvez changer 1 en 2 ou 3 dans le fichier "time.txt". 1 représente
1920x1080P, 2 pour 1280x720P et 3 pour 640x480.
5.7. Si vous n'avez pas besoin de l'horodatage sur la vidéo, modifiez "Y" dans "N"
dans le fichier "time.txt".
Par exemple:
[date]
2017-04-12 14:24:32 N 2
5.8. Redémarrez la caméra et le système met à jour automatiquement le pro-
gramme.
VI. Charger
6.1. Éteignez la caméra et connectez la caméra à une alimentation secteur à l'aide
de l'adaptateur secteur DC5V et du câble USB fourni.
6.2. Les voyants lumineux rouge et bleu resteront allumés pendant le processus de
charge.
6.3. Il faudra 40 minutes pour obtenir une charge complète.
6.4. Le voyant rouge s'éteint et le bleu reste allumé lorsque la caméra est complète-
ment chargé.
VII. Réinitialisation
Si, pour quelque raison que ce soit, l'appareil cesse de répondre ou ne fonctionne
pas correctement, une réinitialisation rapide le rétablira à son fonctionnement
normal.
Fonctionnement: Lorsque la caméra est sous tension, appuyer simultanément sur le
Bouton d’Alimentation et le bouton de mode; La caméra s'éteindra automatique-
ment. Ensuite, vous pouvez redémarrer la caméra avec les paramètres par défaut.
VIII. Réglage de l'heure
8.1. Tirez le Bouton de Réglage du Temps jusqu'à ce que vous entendiez un clic.
Des mains d'une heure et d'une minute seront arrêtées.
8.2. Tournez le Bouton de Réglage du Temps pour régler l'heure.
8.3. Appuyez sur le bouton Réglage du temps après que l'heure est terminée.

I. Vue d'ensemble du produit
1. Couvercle de bouton pour mini port USB
2. Lentille de caméra
3. Bouton d’Alimentation
4. Voyant Vert / Rouge
5. Bouton de Réglage du Temps
6. Voyant Bleu
7. Bouton Mode
8. Emplacement pour Carte Micro SD
II. Qu'y a-t-il dans la Boite
-1 × Caméra Montre
-1 × Câble USB
-1 × AC110-240V à DC 5V adaptateur secteur
-1 × 8 GB de carte Micro SD (monté sur l'emplacement de la carte Micro SD déjà)
III. Opération
>> Avant d'utiliser, assurez-vous que votre appareil photo est complètement chargé.
>> Assurez-vous que la carte Micro SD a déjà été formatée et qu'elle est correcte-
ment installée dans la fente de la carte SD de la caméra, ou elle ne fonctionnera
pas. Nous vous recommandons d'utiliser une carte SD SDHC de classe 10 SD.
[Note]: Si aucune carte Micro SD n'est installée dans la caméra, les voyants lumineux bleu et vert
s'allument pendant 3 secondes, puis le vert s'éteint et le bleu clignotera 2 secondes et s'éteindra. Après
cela, le vert s'allume et clignote 3 fois puis éteint. La caméra s'arrête automatiquement.
3.1. MARCHE/ARRÊT
3.1.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.1.2. Mettez l'appareil hors tension en appuyant de nouveau sur le Bouton d’Ali-
mentation pendant 2 secondes en mode veille. Le voyant vert clignote 3 fois, puis
éteint avec le rouge.
[Note]: La caméra s'arrête automatiquement s'il est en mode veille sans aucune opération pendant
plus de 3 minutes.
3.2. ENREGISTREMENT VIDEO
3.2.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.2.2. Appuyez une fois sur le Bouton d’Alimentation pour commencer l'enregis-
trement vidéo. Le voyant bleu clignote 3 fois et éteint.
3.2.3 Appuyez à nouveau sur le Bouton d’Alimentation pour arrêter l'enregistrement
vidéo. Le voyant bleu s'allume et reste allumé, indiquant que la caméra est en mode
veille.
[Note]:
1). Un clip vidéo sera généré et enregistré toutes les 5 minutes automatiquement.
2). La caméra peut enregistrer une vidéo pendant 120 minutes en continu sur une charge complète.
3). Chaque vidéo prendra environ 380-400 Mo d'espace de stockage de la carte Micro SD.
4). Résolution vidéo optionnel: 1920x1080P, 1280x720P, 640x480 Format vidéo: AVI
5). L'enregistrement en boucle est pris en charge.
6). Si la batterie est faible pendant le processus d'enregistrement vidéo, le voyant vert clignote 15 fois
rapidement, puis clignote 3 fois lentement et éteignez. Ensuite, la caméra enregistre les fichiers vidéo
puis s'éteint automatiquement.
3.3. CAMERA/STILL PHOTOGRAPHIE
3.3.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.3.2. Appuyez deux fois sur le bouton Mode pour entrer en mode photographie fixe.
Les voyants lumineux vert et bleu resteront allumés.
3.3.3. Appuyez une fois sur le Bouton d’Alimentation pour prendre une photo.
Chaque fois que vous prenez une photo, les voyants lumineux vert et bleu clignotent
une fois.
3.4. ENREGISTREMENT AUDIO
3.4.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.4.2. Appuyez une fois sur le bouton Mode pour entrer en mode d'enregistrement
audio. Le témoin lumineux bleu s'éteint lorsque le voyant vert s'allume et reste
solide.
3.4.3. Appuyez une fois sur le Bouton d’Alimentation pour enregistrer uniquement
l'audio. Le voyant vert clignote 3 fois et éteint.
3.4.4. Appuyez à nouveau sur le Bouton d’Alimentation pour arrêter l'enregistrement
audio. Le voyant vert s'allume et reste solide.
[Note]:
1). Un clip audio sera généré et sauvegardé toutes les 30 minutes automatiquement.
2). Format audio: WAV
IV. Téléchargement de Fichiers Vidéo/Image/Audio
4.1. Éteignez la caméra, retirez la carte Micro SD et insérez-la dans un lecteur de
carte.
4.2. Insérez le lecteur de carte dans un port USB approprié pour PC.
4.3. La caméra sera reconnu comme un lecteur de disque amovible.
4.4. Tous les fichiers peuvent être consultés dans le lecteur.
V. Réglage de l'heure/Date Stamp
5.1. Éteignez la caméra, retirez la carte Micro SD et insérez-la dans un lecteur de
carte.
5.2. Insérez le lecteur de carte dans un port USB approprié pour PC.
5.3. La caméra sera reconnu comme un lecteur de disque amovible.
5.4. Cliquez sur le lecteur dans le répertoire racine et dans le répertoire racine,
ouvrez le fichier nommé "time.txt".
5.5. Écrivez la date et l'heure actuelles dans le fichier "time.txt" avec le format cor-
rect:
[date]
AAAA-MM-DD HH: MM: SS Y 1
Par exemple:
[date]
2017-04-12 14:24:32 Y 1
Enregistrez ce fichier.
5.6. Si vous avez besoin de la caméra pour enregistrer une vidéo à une résolution
inférieure, vous pouvez changer 1 en 2 ou 3 dans le fichier "time.txt". 1 représente
1920x1080P, 2 pour 1280x720P et 3 pour 640x480.
5.7. Si vous n'avez pas besoin de l'horodatage sur la vidéo, modifiez "Y" dans "N"
dans le fichier "time.txt".
Par exemple:
[date]
2017-04-12 14:24:32 N 2
5.8. Redémarrez la caméra et le système met à jour automatiquement le pro-
gramme.
VI. Charger
6.1. Éteignez la caméra et connectez la caméra à une alimentation secteur à l'aide
de l'adaptateur secteur DC5V et du câble USB fourni.
6.2. Les voyants lumineux rouge et bleu resteront allumés pendant le processus de
charge.
6.3. Il faudra 40 minutes pour obtenir une charge complète.
6.4. Le voyant rouge s'éteint et le bleu reste allumé lorsque la caméra est complète-
ment chargé.
VII. Réinitialisation
Si, pour quelque raison que ce soit, l'appareil cesse de répondre ou ne fonctionne
pas correctement, une réinitialisation rapide le rétablira à son fonctionnement
normal.
Fonctionnement: Lorsque la caméra est sous tension, appuyer simultanément sur le
Bouton d’Alimentation et le bouton de mode; La caméra s'éteindra automatique-
ment. Ensuite, vous pouvez redémarrer la caméra avec les paramètres par défaut.
VIII. Réglage de l'heure
8.1. Tirez le Bouton de Réglage du Temps jusqu'à ce que vous entendiez un clic.
Des mains d'une heure et d'une minute seront arrêtées.
8.2. Tournez le Bouton de Réglage du Temps pour régler l'heure.
8.3. Appuyez sur le bouton Réglage du temps après que l'heure est terminée.

I. Vue d'ensemble du produit
1. Couvercle de bouton pour mini port USB
2. Lentille de caméra
3. Bouton d’Alimentation
4. Voyant Vert / Rouge
5. Bouton de Réglage du Temps
6. Voyant Bleu
7. Bouton Mode
8. Emplacement pour Carte Micro SD
II. Qu'y a-t-il dans la Boite
-1 × Caméra Montre
-1 × Câble USB
-1 × AC110-240V à DC 5V adaptateur secteur
-1 × 8 GB de carte Micro SD (monté sur l'emplacement de la carte Micro SD déjà)
III. Opération
>> Avant d'utiliser, assurez-vous que votre appareil photo est complètement chargé.
>> Assurez-vous que la carte Micro SD a déjà été formatée et qu'elle est correcte-
ment installée dans la fente de la carte SD de la caméra, ou elle ne fonctionnera
pas. Nous vous recommandons d'utiliser une carte SD SDHC de classe 10 SD.
[Note]: Si aucune carte Micro SD n'est installée dans la caméra, les voyants lumineux bleu et vert
s'allument pendant 3 secondes, puis le vert s'éteint et le bleu clignotera 2 secondes et s'éteindra. Après
cela, le vert s'allume et clignote 3 fois puis éteint. La caméra s'arrête automatiquement.
3.1. MARCHE/ARRÊT
3.1.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.1.2. Mettez l'appareil hors tension en appuyant de nouveau sur le Bouton d’Ali-
mentation pendant 2 secondes en mode veille. Le voyant vert clignote 3 fois, puis
éteint avec le rouge.
[Note]: La caméra s'arrête automatiquement s'il est en mode veille sans aucune opération pendant
plus de 3 minutes.
3.2. ENREGISTREMENT VIDEO
3.2.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.2.2. Appuyez une fois sur le Bouton d’Alimentation pour commencer l'enregis-
trement vidéo. Le voyant bleu clignote 3 fois et éteint.
3.2.3 Appuyez à nouveau sur le Bouton d’Alimentation pour arrêter l'enregistrement
vidéo. Le voyant bleu s'allume et reste allumé, indiquant que la caméra est en mode
veille.
[Note]:
1). Un clip vidéo sera généré et enregistré toutes les 5 minutes automatiquement.
2). La caméra peut enregistrer une vidéo pendant 120 minutes en continu sur une charge complète.
3). Chaque vidéo prendra environ 380-400 Mo d'espace de stockage de la carte Micro SD.
4). Résolution vidéo optionnel: 1920x1080P, 1280x720P, 640x480 Format vidéo: AVI
5). L'enregistrement en boucle est pris en charge.
6). Si la batterie est faible pendant le processus d'enregistrement vidéo, le voyant vert clignote 15 fois
rapidement, puis clignote 3 fois lentement et éteignez. Ensuite, la caméra enregistre les fichiers vidéo
puis s'éteint automatiquement.
3.3. CAMERA/STILL PHOTOGRAPHIE
3.3.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.3.2. Appuyez deux fois sur le bouton Mode pour entrer en mode photographie fixe.
Les voyants lumineux vert et bleu resteront allumés.
3.3.3. Appuyez une fois sur le Bouton d’Alimentation pour prendre une photo.
Chaque fois que vous prenez une photo, les voyants lumineux vert et bleu clignotent
une fois.
3.4. ENREGISTREMENT AUDIO
3.4.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.4.2. Appuyez une fois sur le bouton Mode pour entrer en mode d'enregistrement
audio. Le témoin lumineux bleu s'éteint lorsque le voyant vert s'allume et reste
solide.
3.4.3. Appuyez une fois sur le Bouton d’Alimentation pour enregistrer uniquement
l'audio. Le voyant vert clignote 3 fois et éteint.
3.4.4. Appuyez à nouveau sur le Bouton d’Alimentation pour arrêter l'enregistrement
audio. Le voyant vert s'allume et reste solide.
[Note]:
1). Un clip audio sera généré et sauvegardé toutes les 30 minutes automatiquement.
2). Format audio: WAV
IV. Téléchargement de Fichiers Vidéo/Image/Audio
4.1. Éteignez la caméra, retirez la carte Micro SD et insérez-la dans un lecteur de
carte.
4.2. Insérez le lecteur de carte dans un port USB approprié pour PC.
4.3. La caméra sera reconnu comme un lecteur de disque amovible.
4.4. Tous les fichiers peuvent être consultés dans le lecteur.
V. Réglage de l'heure/Date Stamp
5.1. Éteignez la caméra, retirez la carte Micro SD et insérez-la dans un lecteur de
carte.
5.2. Insérez le lecteur de carte dans un port USB approprié pour PC.
5.3. La caméra sera reconnu comme un lecteur de disque amovible.
5.4. Cliquez sur le lecteur dans le répertoire racine et dans le répertoire racine,
ouvrez le fichier nommé "time.txt".
5.5. Écrivez la date et l'heure actuelles dans le fichier "time.txt" avec le format cor-
rect:
[date]
AAAA-MM-DD HH: MM: SS Y 1
Par exemple:
[date]
2017-04-12 14:24:32 Y 1
Enregistrez ce fichier.
5.6. Si vous avez besoin de la caméra pour enregistrer une vidéo à une résolution
inférieure, vous pouvez changer 1 en 2 ou 3 dans le fichier "time.txt". 1 représente
1920x1080P, 2 pour 1280x720P et 3 pour 640x480.
5.7. Si vous n'avez pas besoin de l'horodatage sur la vidéo, modifiez "Y" dans "N"
dans le fichier "time.txt".
Par exemple:
[date]
2017-04-12 14:24:32 N 2
5.8. Redémarrez la caméra et le système met à jour automatiquement le pro-
gramme.
VI. Charger
6.1. Éteignez la caméra et connectez la caméra à une alimentation secteur à l'aide
de l'adaptateur secteur DC5V et du câble USB fourni.
6.2. Les voyants lumineux rouge et bleu resteront allumés pendant le processus de
charge.
6.3. Il faudra 40 minutes pour obtenir une charge complète.
6.4. Le voyant rouge s'éteint et le bleu reste allumé lorsque la caméra est complète-
ment chargé.
VII. Réinitialisation
Si, pour quelque raison que ce soit, l'appareil cesse de répondre ou ne fonctionne
pas correctement, une réinitialisation rapide le rétablira à son fonctionnement
normal.
Fonctionnement: Lorsque la caméra est sous tension, appuyer simultanément sur le
Bouton d’Alimentation et le bouton de mode; La caméra s'éteindra automatique-
ment. Ensuite, vous pouvez redémarrer la caméra avec les paramètres par défaut.
VIII. Réglage de l'heure
8.1. Tirez le Bouton de Réglage du Temps jusqu'à ce que vous entendiez un clic.
Des mains d'une heure et d'une minute seront arrêtées.
8.2. Tournez le Bouton de Réglage du Temps pour régler l'heure.
8.3. Appuyez sur le bouton Réglage du temps après que l'heure est terminée.

I. Vue d'ensemble du produit
1. Couvercle de bouton pour mini port USB
2. Lentille de caméra
3. Bouton d’Alimentation
4. Voyant Vert / Rouge
5. Bouton de Réglage du Temps
6. Voyant Bleu
7. Bouton Mode
8. Emplacement pour Carte Micro SD
II. Qu'y a-t-il dans la Boite
-1 × Caméra Montre
-1 × Câble USB
-1 × AC110-240V à DC 5V adaptateur secteur
-1 × 8 GB de carte Micro SD (monté sur l'emplacement de la carte Micro SD déjà)
III. Opération
>> Avant d'utiliser, assurez-vous que votre appareil photo est complètement chargé.
>> Assurez-vous que la carte Micro SD a déjà été formatée et qu'elle est correcte-
ment installée dans la fente de la carte SD de la caméra, ou elle ne fonctionnera
pas. Nous vous recommandons d'utiliser une carte SD SDHC de classe 10 SD.
[Note]: Si aucune carte Micro SD n'est installée dans la caméra, les voyants lumineux bleu et vert
s'allument pendant 3 secondes, puis le vert s'éteint et le bleu clignotera 2 secondes et s'éteindra. Après
cela, le vert s'allume et clignote 3 fois puis éteint. La caméra s'arrête automatiquement.
3.1. MARCHE/ARRÊT
3.1.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.1.2. Mettez l'appareil hors tension en appuyant de nouveau sur le Bouton d’Ali-
mentation pendant 2 secondes en mode veille. Le voyant vert clignote 3 fois, puis
éteint avec le rouge.
[Note]: La caméra s'arrête automatiquement s'il est en mode veille sans aucune opération pendant
plus de 3 minutes.
3.2. ENREGISTREMENT VIDEO
3.2.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.2.2. Appuyez une fois sur le Bouton d’Alimentation pour commencer l'enregis-
trement vidéo. Le voyant bleu clignote 3 fois et éteint.
3.2.3 Appuyez à nouveau sur le Bouton d’Alimentation pour arrêter l'enregistrement
vidéo. Le voyant bleu s'allume et reste allumé, indiquant que la caméra est en mode
veille.
[Note]:
1). Un clip vidéo sera généré et enregistré toutes les 5 minutes automatiquement.
2). La caméra peut enregistrer une vidéo pendant 120 minutes en continu sur une charge complète.
3). Chaque vidéo prendra environ 380-400 Mo d'espace de stockage de la carte Micro SD.
4). Résolution vidéo optionnel: 1920x1080P, 1280x720P, 640x480 Format vidéo: AVI
5). L'enregistrement en boucle est pris en charge.
6). Si la batterie est faible pendant le processus d'enregistrement vidéo, le voyant vert clignote 15 fois
rapidement, puis clignote 3 fois lentement et éteignez. Ensuite, la caméra enregistre les fichiers vidéo
puis s'éteint automatiquement.
3.3. CAMERA/STILL PHOTOGRAPHIE
3.3.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.3.2. Appuyez deux fois sur le bouton Mode pour entrer en mode photographie fixe.
Les voyants lumineux vert et bleu resteront allumés.
3.3.3. Appuyez une fois sur le Bouton d’Alimentation pour prendre une photo.
Chaque fois que vous prenez une photo, les voyants lumineux vert et bleu clignotent
une fois.
3.4. ENREGISTREMENT AUDIO
3.4.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.4.2. Appuyez une fois sur le bouton Mode pour entrer en mode d'enregistrement
audio. Le témoin lumineux bleu s'éteint lorsque le voyant vert s'allume et reste
solide.
3.4.3. Appuyez une fois sur le Bouton d’Alimentation pour enregistrer uniquement
l'audio. Le voyant vert clignote 3 fois et éteint.
3.4.4. Appuyez à nouveau sur le Bouton d’Alimentation pour arrêter l'enregistrement
audio. Le voyant vert s'allume et reste solide.
[Note]:
1). Un clip audio sera généré et sauvegardé toutes les 30 minutes automatiquement.
2). Format audio: WAV
IV. Téléchargement de Fichiers Vidéo/Image/Audio
4.1. Éteignez la caméra, retirez la carte Micro SD et insérez-la dans un lecteur de
carte.
4.2. Insérez le lecteur de carte dans un port USB approprié pour PC.
4.3. La caméra sera reconnu comme un lecteur de disque amovible.
4.4. Tous les fichiers peuvent être consultés dans le lecteur.
V. Réglage de l'heure/Date Stamp
5.1. Éteignez la caméra, retirez la carte Micro SD et insérez-la dans un lecteur de
carte.
5.2. Insérez le lecteur de carte dans un port USB approprié pour PC.
5.3. La caméra sera reconnu comme un lecteur de disque amovible.
5.4. Cliquez sur le lecteur dans le répertoire racine et dans le répertoire racine,
ouvrez le fichier nommé "time.txt".
5.5. Écrivez la date et l'heure actuelles dans le fichier "time.txt" avec le format cor-
rect:
[date]
AAAA-MM-DD HH: MM: SS Y 1
Par exemple:
[date]
2017-04-12 14:24:32 Y 1
Enregistrez ce fichier.
5.6. Si vous avez besoin de la caméra pour enregistrer une vidéo à une résolution
inférieure, vous pouvez changer 1 en 2 ou 3 dans le fichier "time.txt". 1 représente
1920x1080P, 2 pour 1280x720P et 3 pour 640x480.
5.7. Si vous n'avez pas besoin de l'horodatage sur la vidéo, modifiez "Y" dans "N"
dans le fichier "time.txt".
Par exemple:
[date]
2017-04-12 14:24:32 N 2
5.8. Redémarrez la caméra et le système met à jour automatiquement le pro-
gramme.
VI. Charger
6.1. Éteignez la caméra et connectez la caméra à une alimentation secteur à l'aide
de l'adaptateur secteur DC5V et du câble USB fourni.
6.2. Les voyants lumineux rouge et bleu resteront allumés pendant le processus de
charge.
6.3. Il faudra 40 minutes pour obtenir une charge complète.
6.4. Le voyant rouge s'éteint et le bleu reste allumé lorsque la caméra est complète-
ment chargé.
VII. Réinitialisation
Si, pour quelque raison que ce soit, l'appareil cesse de répondre ou ne fonctionne
pas correctement, une réinitialisation rapide le rétablira à son fonctionnement
normal.
Fonctionnement: Lorsque la caméra est sous tension, appuyer simultanément sur le
Bouton d’Alimentation et le bouton de mode; La caméra s'éteindra automatique-
ment. Ensuite, vous pouvez redémarrer la caméra avec les paramètres par défaut.
VIII. Réglage de l'heure
8.1. Tirez le Bouton de Réglage du Temps jusqu'à ce que vous entendiez un clic.
Des mains d'une heure et d'une minute seront arrêtées.
8.2. Tournez le Bouton de Réglage du Temps pour régler l'heure.
8.3. Appuyez sur le bouton Réglage du temps après que l'heure est terminée.

I. Vue d'ensemble du produit
1. Couvercle de bouton pour mini port USB
2. Lentille de caméra
3. Bouton d’Alimentation
4. Voyant Vert / Rouge
5. Bouton de Réglage du Temps
6. Voyant Bleu
7. Bouton Mode
8. Emplacement pour Carte Micro SD
II. Qu'y a-t-il dans la Boite
-1 × Caméra Montre
-1 × Câble USB
-1 × AC110-240V à DC 5V adaptateur secteur
-1 × 8 GB de carte Micro SD (monté sur l'emplacement de la carte Micro SD déjà)
III. Opération
>> Avant d'utiliser, assurez-vous que votre appareil photo est complètement chargé.
>> Assurez-vous que la carte Micro SD a déjà été formatée et qu'elle est correcte-
ment installée dans la fente de la carte SD de la caméra, ou elle ne fonctionnera
pas. Nous vous recommandons d'utiliser une carte SD SDHC de classe 10 SD.
[Note]: Si aucune carte Micro SD n'est installée dans la caméra, les voyants lumineux bleu et vert
s'allument pendant 3 secondes, puis le vert s'éteint et le bleu clignotera 2 secondes et s'éteindra. Après
cela, le vert s'allume et clignote 3 fois puis éteint. La caméra s'arrête automatiquement.
3.1. MARCHE/ARRÊT
3.1.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.1.2. Mettez l'appareil hors tension en appuyant de nouveau sur le Bouton d’Ali-
mentation pendant 2 secondes en mode veille. Le voyant vert clignote 3 fois, puis
éteint avec le rouge.
[Note]: La caméra s'arrête automatiquement s'il est en mode veille sans aucune opération pendant
plus de 3 minutes.
3.2. ENREGISTREMENT VIDEO
3.2.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.2.2. Appuyez une fois sur le Bouton d’Alimentation pour commencer l'enregis-
trement vidéo. Le voyant bleu clignote 3 fois et éteint.
3.2.3 Appuyez à nouveau sur le Bouton d’Alimentation pour arrêter l'enregistrement
vidéo. Le voyant bleu s'allume et reste allumé, indiquant que la caméra est en mode
veille.
[Note]:
1). Un clip vidéo sera généré et enregistré toutes les 5 minutes automatiquement.
2). La caméra peut enregistrer une vidéo pendant 120 minutes en continu sur une charge complète.
3). Chaque vidéo prendra environ 380-400 Mo d'espace de stockage de la carte Micro SD.
4). Résolution vidéo optionnel: 1920x1080P, 1280x720P, 640x480 Format vidéo: AVI
5). L'enregistrement en boucle est pris en charge.
6). Si la batterie est faible pendant le processus d'enregistrement vidéo, le voyant vert clignote 15 fois
rapidement, puis clignote 3 fois lentement et éteignez. Ensuite, la caméra enregistre les fichiers vidéo
puis s'éteint automatiquement.
3.3. CAMERA/STILL PHOTOGRAPHIE
3.3.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.3.2. Appuyez deux fois sur le bouton Mode pour entrer en mode photographie fixe.
Les voyants lumineux vert et bleu resteront allumés.
3.3.3. Appuyez une fois sur le Bouton d’Alimentation pour prendre une photo.
Chaque fois que vous prenez une photo, les voyants lumineux vert et bleu clignotent
une fois.
3.4. ENREGISTREMENT AUDIO
3.4.1. Allumez la caméra en appuyant sur le Bouton d’Alimentation pendant 2 sec-
ondes. Les voyants bleu et vert s'allument pendant 2 secondes, puis le vert s'éteint
lorsque le bleu reste allumé, indiquant que la caméra est entré en mode veille au-
tomatiquement.
3.4.2. Appuyez une fois sur le bouton Mode pour entrer en mode d'enregistrement
audio. Le témoin lumineux bleu s'éteint lorsque le voyant vert s'allume et reste
solide.
3.4.3. Appuyez une fois sur le Bouton d’Alimentation pour enregistrer uniquement
l'audio. Le voyant vert clignote 3 fois et éteint.
3.4.4. Appuyez à nouveau sur le Bouton d’Alimentation pour arrêter l'enregistrement
audio. Le voyant vert s'allume et reste solide.
[Note]:
1). Un clip audio sera généré et sauvegardé toutes les 30 minutes automatiquement.
2). Format audio: WAV
IV. Téléchargement de Fichiers Vidéo/Image/Audio
4.1. Éteignez la caméra, retirez la carte Micro SD et insérez-la dans un lecteur de
carte.
4.2. Insérez le lecteur de carte dans un port USB approprié pour PC.
4.3. La caméra sera reconnu comme un lecteur de disque amovible.
4.4. Tous les fichiers peuvent être consultés dans le lecteur.
V. Réglage de l'heure/Date Stamp
5.1. Éteignez la caméra, retirez la carte Micro SD et insérez-la dans un lecteur de
carte.
5.2. Insérez le lecteur de carte dans un port USB approprié pour PC.
5.3. La caméra sera reconnu comme un lecteur de disque amovible.
5.4. Cliquez sur le lecteur dans le répertoire racine et dans le répertoire racine,
ouvrez le fichier nommé "time.txt".
5.5. Écrivez la date et l'heure actuelles dans le fichier "time.txt" avec le format cor-
rect:
[date]
AAAA-MM-DD HH: MM: SS Y 1
Par exemple:
[date]
2017-04-12 14:24:32 Y 1
Enregistrez ce fichier.
5.6. Si vous avez besoin de la caméra pour enregistrer une vidéo à une résolution
inférieure, vous pouvez changer 1 en 2 ou 3 dans le fichier "time.txt". 1 représente
1920x1080P, 2 pour 1280x720P et 3 pour 640x480.
5.7. Si vous n'avez pas besoin de l'horodatage sur la vidéo, modifiez "Y" dans "N"
dans le fichier "time.txt".
Par exemple:
[date]
2017-04-12 14:24:32 N 2
5.8. Redémarrez la caméra et le système met à jour automatiquement le pro-
gramme.
VI. Charger
6.1. Éteignez la caméra et connectez la caméra à une alimentation secteur à l'aide
de l'adaptateur secteur DC5V et du câble USB fourni.
6.2. Les voyants lumineux rouge et bleu resteront allumés pendant le processus de
charge.
6.3. Il faudra 40 minutes pour obtenir une charge complète.
6.4. Le voyant rouge s'éteint et le bleu reste allumé lorsque la caméra est complète-
ment chargé.
VII. Réinitialisation
Si, pour quelque raison que ce soit, l'appareil cesse de répondre ou ne fonctionne
pas correctement, une réinitialisation rapide le rétablira à son fonctionnement
normal.
Fonctionnement: Lorsque la caméra est sous tension, appuyer simultanément sur le
Bouton d’Alimentation et le bouton de mode; La caméra s'éteindra automatique-
ment. Ensuite, vous pouvez redémarrer la caméra avec les paramètres par défaut.
VIII. Réglage de l'heure
8.1. Tirez le Bouton de Réglage du Temps jusqu'à ce que vous entendiez un clic.
Des mains d'une heure et d'une minute seront arrêtées.
8.2. Tournez le Bouton de Réglage du Temps pour régler l'heure.
8.3. Appuyez sur le bouton Réglage du temps après que l'heure est terminée.

W8200
Guida Utente
I. Panoramica del Prodotto
1. Copertura Manopola per la Porta Mini USB
2. Camera Lens
3.Pulsante di Alimentazione
4. Verde / Rossa Spia
5. Tempo Manopola di Regolazione
6. Indicatore Luminoso Blu
7. Pulsante Modalità
8. Slot Micro SD Card
II. Cosa c'è nella Scatola
-1 × Vigilanza Della Macchina Fotografica
-1 × Cavo USB
-1 × AC110-240V a CC Adattatore di Alimentazione 5V
-1 × 8 GB Micro SD Card (montato nello slot per schede Micro SD già)
III. Operazione
>> Prima di utilizzare, assicurarsi che la fotocamera sia completamente carica.
>> Si prega di verificare che la scheda Micro SD è stata formattata già ed è dotato
saldamente nella slot per scheda SD della fotocamera, o non funzionerà. Si con-
siglia di utilizzare una scheda SD SDHC Classe 10 Micro.
[Nota]: Se nessuna scheda micro SD è montata nella telecamera, sia l'indicatore blu e verde le luci
saranno illuminati per 3 secondi, poi quello verde si spegne e quello blu lampeggerà 2 secondi e speg-
nere. Dopo di che, quello verde si accende e lampeggia per 3 volte poi si spengono. La fotocamera si
spegne automaticamente.
3.1. ACCENSIONE/SPEGNIMENTO
3.1.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.1.2. Spegnere la fotocamera premendo il pulsante di accensione per 2 secondi in
modalità standby. La spia verde lampeggia 3 volte e poi spegnere insieme con il
rosso.
[Nota]: La fotocamera si spegne automaticamente se è in modalità standby, senza alcuna operazi-
one più di 3 minuti.
3.2. REGISTRAZIONE VIDEO
3.2.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.2.2. Premere il tasto Power una volta per avviare la registrazione video. L'indica-
tore luminoso blu lampeggia 3 volte e spegnere.
3.2.3. Premere il tasto Power una volta per interrompere la registrazione del video.
La spia blu si accende e rimane accesa, indicando la fotocamera è in modalità
standby.
[Nota]:
1). Un video clip verrà generata e salvata automaticamente ogni 5 minuti.
2). La fotocamera può registrare video in continuo per 120 minuti su una carica completa.
3). Ogni clip video verrà occupare circa 380-400MB spazio della scheda Micro SD stoccaggio.
4). Risoluzione video opzionale: 1920x1080P, 1280x720P, 640x480 video Formato: AVI
5). registrazione in loop è supportato.
6). Se la batteria è scarica durante il processo di registrazione video, la spia verde lampeggia 15 volte
velocemente allora lampeggiano 3 volte lentamente e si spengono. Poi la fotocamera salverà file video
poi si spegnerà automaticamente.
3.3. CAMERA/LA FOTOGRAFIA
3.3.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.3.2. Premere il tasto MODE due volte per entrare in modalità ancora fotografare.
Entrambe le spie verdi e blu rimarranno illuminati.
3.3.3. Premere il tasto Power una volta per scattare una foto. Ogni volta che si
scatta una foto, entrambe le spie verdi e blu lampeggerà una volta.
3.4. REGISTRAZIONE AUDIO
3.4.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.4.2. Premere il pulsante Mode una volta per entrare in modalità di registrazione
audio. La spia blu si spegne mentre la spia verde si accende e rimane solido.
3.4.3. Premere il tasto Power una volta per registrare solo l'audio. La spia verde
lampeggia 3 volte e spegnere.
3.4.4. Premere il tasto Power una volta per interrompere la registrazione audio. La
spia verde si accende e rimane solida.
[Nota]:
1). Una clip audio viene generata e salvata automaticamente ogni 30 minuti.
2). Formato audio: WAV
IV. Caricamento di File Video/Immagini/Audio
4.1. Spegnere la fotocamera, rimuovere la scheda Micro SD e inserirla in un lettore
di schede.
4.2. Inserire il lettore di schede in una porta USB del computer corretta PC.
4.3. La fotocamera viene riconosciuta come unità disco rimovibile.
4.4. Tutti i file sono accessibili nel drive.
V. Impostazione Ora/Data
5.1. Spegnere la fotocamera, rimuovere la scheda Micro SD e inserirla in un lettore
di schede.
5.2. Inserire il lettore di schede in una porta USB del computer corretta PC.
5.3. La fotocamera viene riconosciuta come unità disco rimovibile.
5.4. Fare clic sul disco nella directory principale e all'interno della directory princi-
pale, aprire il file denominato “time.txt”.
5.5. Scrivere la data e l'ora correnti nel file “time.txt” con il formato corretto:
[date]
AAAA-MM-GG HH: MM: SS Y 1
Per esempio:
[date]
2017-04-12 14:24:32 Y 1
Salvare il file.
5.6. Se è necessario la fotocamera per registrare video a una risoluzione più bassa,
è possibile modificare 1 in 2 o 3 nel file “time.txt”. 1 sta per 1920x1080P, 2 per
1280x720P e 3 per 640x480.
5.7. Se non è necessario il timestamp sul video riprese, cambiare “Y” in “N” nel file
“time.txt”.
Per esempio:
[date]
2017-04-12 14:24:32 N 2
5.8. Riavviare la telecamera e il sistema aggiornerà automaticamente il programma.
VI. Ricarica
6.1. Spegnere la fotocamera e collegare la fotocamera a una presa di alimentazione
CA mediante l'alimentatore DC5V e il cavo USB fornito.
6.2. Entrambe le spie rosse e blu rimarranno illuminati durante il processo di carica.
6.3. Ci vorranno 40 minuti per ottenere una carica completa.
6.4. La spia rossa si spegne e il blu rimane accesa quando la telecamera è comple-
tamente carica.
VII. Ripristino
Se per qualsiasi motivo, la fotocamera smette di rispondere o non funziona corretta-
mente, eseguire un ripristino rapido ripristinerà di nuovo al normale funzionamento.
Funzionamento: Quando la fotocamera è accesa, premere il pulsante di accensi-
one e il tasto Modalità contemporaneamente una volta; la fotocamera si spegne au-
tomaticamente. Quindi è possibile riavviare la macchina fotografica con le
impostazioni predefinite di fabbrica.
VIII. Impostazioni Orario
8.1. Estrarre la regolazione dell'ora manopola fino a sentire un clic. Sia lancette delle
ore e dei minuti essere fermati.
8.2. Ruotare il tempo manopola di regolazione per impostare l'ora.
8.3. Spingere la regolazione dell'ora manopola indietro dopo il tempo impostato è
completata.

I. Panoramica del Prodotto
1. Copertura Manopola per la Porta Mini USB
2. Camera Lens
3.Pulsante di Alimentazione
4. Verde / Rossa Spia
5. Tempo Manopola di Regolazione
6. Indicatore Luminoso Blu
7. Pulsante Modalità
8. Slot Micro SD Card
II. Cosa c'è nella Scatola
-1 × Vigilanza Della Macchina Fotografica
-1 × Cavo USB
-1 × AC110-240V a CC Adattatore di Alimentazione 5V
-1 × 8 GB Micro SD Card (montato nello slot per schede Micro SD già)
III. Operazione
>> Prima di utilizzare, assicurarsi che la fotocamera sia completamente carica.
>> Si prega di verificare che la scheda Micro SD è stata formattata già ed è dotato
saldamente nella slot per scheda SD della fotocamera, o non funzionerà. Si con-
siglia di utilizzare una scheda SD SDHC Classe 10 Micro.
[Nota]: Se nessuna scheda micro SD è montata nella telecamera, sia l'indicatore blu e verde le luci
saranno illuminati per 3 secondi, poi quello verde si spegne e quello blu lampeggerà 2 secondi e speg-
nere. Dopo di che, quello verde si accende e lampeggia per 3 volte poi si spengono. La fotocamera si
spegne automaticamente.
3.1. ACCENSIONE/SPEGNIMENTO
3.1.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.1.2. Spegnere la fotocamera premendo il pulsante di accensione per 2 secondi in
modalità standby. La spia verde lampeggia 3 volte e poi spegnere insieme con il
rosso.
[Nota]: La fotocamera si spegne automaticamente se è in modalità standby, senza alcuna operazi-
one più di 3 minuti.
3.2. REGISTRAZIONE VIDEO
3.2.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.2.2. Premere il tasto Power una volta per avviare la registrazione video. L'indica-
tore luminoso blu lampeggia 3 volte e spegnere.
3.2.3. Premere il tasto Power una volta per interrompere la registrazione del video.
La spia blu si accende e rimane accesa, indicando la fotocamera è in modalità
standby.
[Nota]:
1). Un video clip verrà generata e salvata automaticamente ogni 5 minuti.
2). La fotocamera può registrare video in continuo per 120 minuti su una carica completa.
3). Ogni clip video verrà occupare circa 380-400MB spazio della scheda Micro SD stoccaggio.
4). Risoluzione video opzionale: 1920x1080P, 1280x720P, 640x480 video Formato: AVI
5). registrazione in loop è supportato.
6). Se la batteria è scarica durante il processo di registrazione video, la spia verde lampeggia 15 volte
velocemente allora lampeggiano 3 volte lentamente e si spengono. Poi la fotocamera salverà file video
poi si spegnerà automaticamente.
3.3. CAMERA/LA FOTOGRAFIA
3.3.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.3.2. Premere il tasto MODE due volte per entrare in modalità ancora fotografare.
Entrambe le spie verdi e blu rimarranno illuminati.
3.3.3. Premere il tasto Power una volta per scattare una foto. Ogni volta che si
scatta una foto, entrambe le spie verdi e blu lampeggerà una volta.
3.4. REGISTRAZIONE AUDIO
3.4.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.4.2. Premere il pulsante Mode una volta per entrare in modalità di registrazione
audio. La spia blu si spegne mentre la spia verde si accende e rimane solido.
3.4.3. Premere il tasto Power una volta per registrare solo l'audio. La spia verde
lampeggia 3 volte e spegnere.
3.4.4. Premere il tasto Power una volta per interrompere la registrazione audio. La
spia verde si accende e rimane solida.
[Nota]:
1). Una clip audio viene generata e salvata automaticamente ogni 30 minuti.
2). Formato audio: WAV
IV. Caricamento di File Video/Immagini/Audio
4.1. Spegnere la fotocamera, rimuovere la scheda Micro SD e inserirla in un lettore
di schede.
4.2. Inserire il lettore di schede in una porta USB del computer corretta PC.
4.3. La fotocamera viene riconosciuta come unità disco rimovibile.
4.4. Tutti i file sono accessibili nel drive.
V. Impostazione Ora/Data
5.1. Spegnere la fotocamera, rimuovere la scheda Micro SD e inserirla in un lettore
di schede.
5.2. Inserire il lettore di schede in una porta USB del computer corretta PC.
5.3. La fotocamera viene riconosciuta come unità disco rimovibile.
5.4. Fare clic sul disco nella directory principale e all'interno della directory princi-
pale, aprire il file denominato “time.txt”.
5.5. Scrivere la data e l'ora correnti nel file “time.txt” con il formato corretto:
[date]
AAAA-MM-GG HH: MM: SS Y 1
Per esempio:
[date]
2017-04-12 14:24:32 Y 1
Salvare il file.
5.6. Se è necessario la fotocamera per registrare video a una risoluzione più bassa,
è possibile modificare 1 in 2 o 3 nel file “time.txt”. 1 sta per 1920x1080P, 2 per
1280x720P e 3 per 640x480.
5.7. Se non è necessario il timestamp sul video riprese, cambiare “Y” in “N” nel file
“time.txt”.
Per esempio:
[date]
2017-04-12 14:24:32 N 2
5.8. Riavviare la telecamera e il sistema aggiornerà automaticamente il programma.
VI. Ricarica
6.1. Spegnere la fotocamera e collegare la fotocamera a una presa di alimentazione
CA mediante l'alimentatore DC5V e il cavo USB fornito.
6.2. Entrambe le spie rosse e blu rimarranno illuminati durante il processo di carica.
6.3. Ci vorranno 40 minuti per ottenere una carica completa.
6.4. La spia rossa si spegne e il blu rimane accesa quando la telecamera è comple-
tamente carica.
VII. Ripristino
Se per qualsiasi motivo, la fotocamera smette di rispondere o non funziona corretta-
mente, eseguire un ripristino rapido ripristinerà di nuovo al normale funzionamento.
Funzionamento: Quando la fotocamera è accesa, premere il pulsante di accensi-
one e il tasto Modalità contemporaneamente una volta; la fotocamera si spegne au-
tomaticamente. Quindi è possibile riavviare la macchina fotografica con le
impostazioni predefinite di fabbrica.
VIII. Impostazioni Orario
8.1. Estrarre la regolazione dell'ora manopola fino a sentire un clic. Sia lancette delle
ore e dei minuti essere fermati.
8.2. Ruotare il tempo manopola di regolazione per impostare l'ora.
8.3. Spingere la regolazione dell'ora manopola indietro dopo il tempo impostato è
completata.

I. Panoramica del Prodotto
1. Copertura Manopola per la Porta Mini USB
2. Camera Lens
3.Pulsante di Alimentazione
4. Verde / Rossa Spia
5. Tempo Manopola di Regolazione
6. Indicatore Luminoso Blu
7. Pulsante Modalità
8. Slot Micro SD Card
II. Cosa c'è nella Scatola
-1 × Vigilanza Della Macchina Fotografica
-1 × Cavo USB
-1 × AC110-240V a CC Adattatore di Alimentazione 5V
-1 × 8 GB Micro SD Card (montato nello slot per schede Micro SD già)
III. Operazione
>> Prima di utilizzare, assicurarsi che la fotocamera sia completamente carica.
>> Si prega di verificare che la scheda Micro SD è stata formattata già ed è dotato
saldamente nella slot per scheda SD della fotocamera, o non funzionerà. Si con-
siglia di utilizzare una scheda SD SDHC Classe 10 Micro.
[Nota]: Se nessuna scheda micro SD è montata nella telecamera, sia l'indicatore blu e verde le luci
saranno illuminati per 3 secondi, poi quello verde si spegne e quello blu lampeggerà 2 secondi e speg-
nere. Dopo di che, quello verde si accende e lampeggia per 3 volte poi si spengono. La fotocamera si
spegne automaticamente.
3.1. ACCENSIONE/SPEGNIMENTO
3.1.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.1.2. Spegnere la fotocamera premendo il pulsante di accensione per 2 secondi in
modalità standby. La spia verde lampeggia 3 volte e poi spegnere insieme con il
rosso.
[Nota]: La fotocamera si spegne automaticamente se è in modalità standby, senza alcuna operazi-
one più di 3 minuti.
3.2. REGISTRAZIONE VIDEO
3.2.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.2.2. Premere il tasto Power una volta per avviare la registrazione video. L'indica-
tore luminoso blu lampeggia 3 volte e spegnere.
3.2.3. Premere il tasto Power una volta per interrompere la registrazione del video.
La spia blu si accende e rimane accesa, indicando la fotocamera è in modalità
standby.
[Nota]:
1). Un video clip verrà generata e salvata automaticamente ogni 5 minuti.
2). La fotocamera può registrare video in continuo per 120 minuti su una carica completa.
3). Ogni clip video verrà occupare circa 380-400MB spazio della scheda Micro SD stoccaggio.
4). Risoluzione video opzionale: 1920x1080P, 1280x720P, 640x480 video Formato: AVI
5). registrazione in loop è supportato.
6). Se la batteria è scarica durante il processo di registrazione video, la spia verde lampeggia 15 volte
velocemente allora lampeggiano 3 volte lentamente e si spengono. Poi la fotocamera salverà file video
poi si spegnerà automaticamente.
3.3. CAMERA/LA FOTOGRAFIA
3.3.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.3.2. Premere il tasto MODE due volte per entrare in modalità ancora fotografare.
Entrambe le spie verdi e blu rimarranno illuminati.
3.3.3. Premere il tasto Power una volta per scattare una foto. Ogni volta che si
scatta una foto, entrambe le spie verdi e blu lampeggerà una volta.
3.4. REGISTRAZIONE AUDIO
3.4.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.4.2. Premere il pulsante Mode una volta per entrare in modalità di registrazione
audio. La spia blu si spegne mentre la spia verde si accende e rimane solido.
3.4.3. Premere il tasto Power una volta per registrare solo l'audio. La spia verde
lampeggia 3 volte e spegnere.
3.4.4. Premere il tasto Power una volta per interrompere la registrazione audio. La
spia verde si accende e rimane solida.
[Nota]:
1). Una clip audio viene generata e salvata automaticamente ogni 30 minuti.
2). Formato audio: WAV
IV. Caricamento di File Video/Immagini/Audio
4.1. Spegnere la fotocamera, rimuovere la scheda Micro SD e inserirla in un lettore
di schede.
4.2. Inserire il lettore di schede in una porta USB del computer corretta PC.
4.3. La fotocamera viene riconosciuta come unità disco rimovibile.
4.4. Tutti i file sono accessibili nel drive.
V. Impostazione Ora/Data
5.1. Spegnere la fotocamera, rimuovere la scheda Micro SD e inserirla in un lettore
di schede.
5.2. Inserire il lettore di schede in una porta USB del computer corretta PC.
5.3. La fotocamera viene riconosciuta come unità disco rimovibile.
5.4. Fare clic sul disco nella directory principale e all'interno della directory princi-
pale, aprire il file denominato “time.txt”.
5.5. Scrivere la data e l'ora correnti nel file “time.txt” con il formato corretto:
[date]
AAAA-MM-GG HH: MM: SS Y 1
Per esempio:
[date]
2017-04-12 14:24:32 Y 1
Salvare il file.
5.6. Se è necessario la fotocamera per registrare video a una risoluzione più bassa,
è possibile modificare 1 in 2 o 3 nel file “time.txt”. 1 sta per 1920x1080P, 2 per
1280x720P e 3 per 640x480.
5.7. Se non è necessario il timestamp sul video riprese, cambiare “Y” in “N” nel file
“time.txt”.
Per esempio:
[date]
2017-04-12 14:24:32 N 2
5.8. Riavviare la telecamera e il sistema aggiornerà automaticamente il programma.
VI. Ricarica
6.1. Spegnere la fotocamera e collegare la fotocamera a una presa di alimentazione
CA mediante l'alimentatore DC5V e il cavo USB fornito.
6.2. Entrambe le spie rosse e blu rimarranno illuminati durante il processo di carica.
6.3. Ci vorranno 40 minuti per ottenere una carica completa.
6.4. La spia rossa si spegne e il blu rimane accesa quando la telecamera è comple-
tamente carica.
VII. Ripristino
Se per qualsiasi motivo, la fotocamera smette di rispondere o non funziona corretta-
mente, eseguire un ripristino rapido ripristinerà di nuovo al normale funzionamento.
Funzionamento: Quando la fotocamera è accesa, premere il pulsante di accensi-
one e il tasto Modalità contemporaneamente una volta; la fotocamera si spegne au-
tomaticamente. Quindi è possibile riavviare la macchina fotografica con le
impostazioni predefinite di fabbrica.
VIII. Impostazioni Orario
8.1. Estrarre la regolazione dell'ora manopola fino a sentire un clic. Sia lancette delle
ore e dei minuti essere fermati.
8.2. Ruotare il tempo manopola di regolazione per impostare l'ora.
8.3. Spingere la regolazione dell'ora manopola indietro dopo il tempo impostato è
completata.

I. Panoramica del Prodotto
1. Copertura Manopola per la Porta Mini USB
2. Camera Lens
3.Pulsante di Alimentazione
4. Verde / Rossa Spia
5. Tempo Manopola di Regolazione
6. Indicatore Luminoso Blu
7. Pulsante Modalità
8. Slot Micro SD Card
II. Cosa c'è nella Scatola
-1 × Vigilanza Della Macchina Fotografica
-1 × Cavo USB
-1 × AC110-240V a CC Adattatore di Alimentazione 5V
-1 × 8 GB Micro SD Card (montato nello slot per schede Micro SD già)
III. Operazione
>> Prima di utilizzare, assicurarsi che la fotocamera sia completamente carica.
>> Si prega di verificare che la scheda Micro SD è stata formattata già ed è dotato
saldamente nella slot per scheda SD della fotocamera, o non funzionerà. Si con-
siglia di utilizzare una scheda SD SDHC Classe 10 Micro.
[Nota]: Se nessuna scheda micro SD è montata nella telecamera, sia l'indicatore blu e verde le luci
saranno illuminati per 3 secondi, poi quello verde si spegne e quello blu lampeggerà 2 secondi e speg-
nere. Dopo di che, quello verde si accende e lampeggia per 3 volte poi si spengono. La fotocamera si
spegne automaticamente.
3.1. ACCENSIONE/SPEGNIMENTO
3.1.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.1.2. Spegnere la fotocamera premendo il pulsante di accensione per 2 secondi in
modalità standby. La spia verde lampeggia 3 volte e poi spegnere insieme con il
rosso.
[Nota]: La fotocamera si spegne automaticamente se è in modalità standby, senza alcuna operazi-
one più di 3 minuti.
3.2. REGISTRAZIONE VIDEO
3.2.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.2.2. Premere il tasto Power una volta per avviare la registrazione video. L'indica-
tore luminoso blu lampeggia 3 volte e spegnere.
3.2.3. Premere il tasto Power una volta per interrompere la registrazione del video.
La spia blu si accende e rimane accesa, indicando la fotocamera è in modalità
standby.
[Nota]:
1). Un video clip verrà generata e salvata automaticamente ogni 5 minuti.
2). La fotocamera può registrare video in continuo per 120 minuti su una carica completa.
3). Ogni clip video verrà occupare circa 380-400MB spazio della scheda Micro SD stoccaggio.
4). Risoluzione video opzionale: 1920x1080P, 1280x720P, 640x480 video Formato: AVI
5). registrazione in loop è supportato.
6). Se la batteria è scarica durante il processo di registrazione video, la spia verde lampeggia 15 volte
velocemente allora lampeggiano 3 volte lentamente e si spengono. Poi la fotocamera salverà file video
poi si spegnerà automaticamente.
3.3. CAMERA/LA FOTOGRAFIA
3.3.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.3.2. Premere il tasto MODE due volte per entrare in modalità ancora fotografare.
Entrambe le spie verdi e blu rimarranno illuminati.
3.3.3. Premere il tasto Power una volta per scattare una foto. Ogni volta che si
scatta una foto, entrambe le spie verdi e blu lampeggerà una volta.
3.4. REGISTRAZIONE AUDIO
3.4.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.4.2. Premere il pulsante Mode una volta per entrare in modalità di registrazione
audio. La spia blu si spegne mentre la spia verde si accende e rimane solido.
3.4.3. Premere il tasto Power una volta per registrare solo l'audio. La spia verde
lampeggia 3 volte e spegnere.
3.4.4. Premere il tasto Power una volta per interrompere la registrazione audio. La
spia verde si accende e rimane solida.
[Nota]:
1). Una clip audio viene generata e salvata automaticamente ogni 30 minuti.
2). Formato audio: WAV
IV. Caricamento di File Video/Immagini/Audio
4.1. Spegnere la fotocamera, rimuovere la scheda Micro SD e inserirla in un lettore
di schede.
4.2. Inserire il lettore di schede in una porta USB del computer corretta PC.
4.3. La fotocamera viene riconosciuta come unità disco rimovibile.
4.4. Tutti i file sono accessibili nel drive.
V. Impostazione Ora/Data
5.1. Spegnere la fotocamera, rimuovere la scheda Micro SD e inserirla in un lettore
di schede.
5.2. Inserire il lettore di schede in una porta USB del computer corretta PC.
5.3. La fotocamera viene riconosciuta come unità disco rimovibile.
5.4. Fare clic sul disco nella directory principale e all'interno della directory princi-
pale, aprire il file denominato “time.txt”.
5.5. Scrivere la data e l'ora correnti nel file “time.txt” con il formato corretto:
[date]
AAAA-MM-GG HH: MM: SS Y 1
Per esempio:
[date]
2017-04-12 14:24:32 Y 1
Salvare il file.
5.6. Se è necessario la fotocamera per registrare video a una risoluzione più bassa,
è possibile modificare 1 in 2 o 3 nel file “time.txt”. 1 sta per 1920x1080P, 2 per
1280x720P e 3 per 640x480.
5.7. Se non è necessario il timestamp sul video riprese, cambiare “Y” in “N” nel file
“time.txt”.
Per esempio:
[date]
2017-04-12 14:24:32 N 2
5.8. Riavviare la telecamera e il sistema aggiornerà automaticamente il programma.
VI. Ricarica
6.1. Spegnere la fotocamera e collegare la fotocamera a una presa di alimentazione
CA mediante l'alimentatore DC5V e il cavo USB fornito.
6.2. Entrambe le spie rosse e blu rimarranno illuminati durante il processo di carica.
6.3. Ci vorranno 40 minuti per ottenere una carica completa.
6.4. La spia rossa si spegne e il blu rimane accesa quando la telecamera è comple-
tamente carica.
VII. Ripristino
Se per qualsiasi motivo, la fotocamera smette di rispondere o non funziona corretta-
mente, eseguire un ripristino rapido ripristinerà di nuovo al normale funzionamento.
Funzionamento: Quando la fotocamera è accesa, premere il pulsante di accensi-
one e il tasto Modalità contemporaneamente una volta; la fotocamera si spegne au-
tomaticamente. Quindi è possibile riavviare la macchina fotografica con le
impostazioni predefinite di fabbrica.
VIII. Impostazioni Orario
8.1. Estrarre la regolazione dell'ora manopola fino a sentire un clic. Sia lancette delle
ore e dei minuti essere fermati.
8.2. Ruotare il tempo manopola di regolazione per impostare l'ora.
8.3. Spingere la regolazione dell'ora manopola indietro dopo il tempo impostato è
completata.

I. Panoramica del Prodotto
1. Copertura Manopola per la Porta Mini USB
2. Camera Lens
3.Pulsante di Alimentazione
4. Verde / Rossa Spia
5. Tempo Manopola di Regolazione
6. Indicatore Luminoso Blu
7. Pulsante Modalità
8. Slot Micro SD Card
II. Cosa c'è nella Scatola
-1 × Vigilanza Della Macchina Fotografica
-1 × Cavo USB
-1 × AC110-240V a CC Adattatore di Alimentazione 5V
-1 × 8 GB Micro SD Card (montato nello slot per schede Micro SD già)
III. Operazione
>> Prima di utilizzare, assicurarsi che la fotocamera sia completamente carica.
>> Si prega di verificare che la scheda Micro SD è stata formattata già ed è dotato
saldamente nella slot per scheda SD della fotocamera, o non funzionerà. Si con-
siglia di utilizzare una scheda SD SDHC Classe 10 Micro.
[Nota]: Se nessuna scheda micro SD è montata nella telecamera, sia l'indicatore blu e verde le luci
saranno illuminati per 3 secondi, poi quello verde si spegne e quello blu lampeggerà 2 secondi e speg-
nere. Dopo di che, quello verde si accende e lampeggia per 3 volte poi si spengono. La fotocamera si
spegne automaticamente.
3.1. ACCENSIONE/SPEGNIMENTO
3.1.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.1.2. Spegnere la fotocamera premendo il pulsante di accensione per 2 secondi in
modalità standby. La spia verde lampeggia 3 volte e poi spegnere insieme con il
rosso.
[Nota]: La fotocamera si spegne automaticamente se è in modalità standby, senza alcuna operazi-
one più di 3 minuti.
3.2. REGISTRAZIONE VIDEO
3.2.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.2.2. Premere il tasto Power una volta per avviare la registrazione video. L'indica-
tore luminoso blu lampeggia 3 volte e spegnere.
3.2.3. Premere il tasto Power una volta per interrompere la registrazione del video.
La spia blu si accende e rimane accesa, indicando la fotocamera è in modalità
standby.
[Nota]:
1). Un video clip verrà generata e salvata automaticamente ogni 5 minuti.
2). La fotocamera può registrare video in continuo per 120 minuti su una carica completa.
3). Ogni clip video verrà occupare circa 380-400MB spazio della scheda Micro SD stoccaggio.
4). Risoluzione video opzionale: 1920x1080P, 1280x720P, 640x480 video Formato: AVI
5). registrazione in loop è supportato.
6). Se la batteria è scarica durante il processo di registrazione video, la spia verde lampeggia 15 volte
velocemente allora lampeggiano 3 volte lentamente e si spengono. Poi la fotocamera salverà file video
poi si spegnerà automaticamente.
3.3. CAMERA/LA FOTOGRAFIA
3.3.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.3.2. Premere il tasto MODE due volte per entrare in modalità ancora fotografare.
Entrambe le spie verdi e blu rimarranno illuminati.
3.3.3. Premere il tasto Power una volta per scattare una foto. Ogni volta che si
scatta una foto, entrambe le spie verdi e blu lampeggerà una volta.
3.4. REGISTRAZIONE AUDIO
3.4.1. Accendere la fotocamera premendo il pulsante di accensione per 2 secondi.
Sia blu e verdi spie si illuminano per 2 secondi e quindi quello verde si spegne
mentre quello blu rimane accesa, indicante che è entrato automaticamente in mo-
dalità standby.
3.4.2. Premere il pulsante Mode una volta per entrare in modalità di registrazione
audio. La spia blu si spegne mentre la spia verde si accende e rimane solido.
3.4.3. Premere il tasto Power una volta per registrare solo l'audio. La spia verde
lampeggia 3 volte e spegnere.
3.4.4. Premere il tasto Power una volta per interrompere la registrazione audio. La
spia verde si accende e rimane solida.
[Nota]:
1). Una clip audio viene generata e salvata automaticamente ogni 30 minuti.
2). Formato audio: WAV
IV. Caricamento di File Video/Immagini/Audio
4.1. Spegnere la fotocamera, rimuovere la scheda Micro SD e inserirla in un lettore
di schede.
4.2. Inserire il lettore di schede in una porta USB del computer corretta PC.
4.3. La fotocamera viene riconosciuta come unità disco rimovibile.
4.4. Tutti i file sono accessibili nel drive.
V. Impostazione Ora/Data
5.1. Spegnere la fotocamera, rimuovere la scheda Micro SD e inserirla in un lettore
di schede.
5.2. Inserire il lettore di schede in una porta USB del computer corretta PC.
5.3. La fotocamera viene riconosciuta come unità disco rimovibile.
5.4. Fare clic sul disco nella directory principale e all'interno della directory princi-
pale, aprire il file denominato “time.txt”.
5.5. Scrivere la data e l'ora correnti nel file “time.txt” con il formato corretto:
[date]
AAAA-MM-GG HH: MM: SS Y 1
Per esempio:
[date]
2017-04-12 14:24:32 Y 1
Salvare il file.
5.6. Se è necessario la fotocamera per registrare video a una risoluzione più bassa,
è possibile modificare 1 in 2 o 3 nel file “time.txt”. 1 sta per 1920x1080P, 2 per
1280x720P e 3 per 640x480.
5.7. Se non è necessario il timestamp sul video riprese, cambiare “Y” in “N” nel file
“time.txt”.
Per esempio:
[date]
2017-04-12 14:24:32 N 2
5.8. Riavviare la telecamera e il sistema aggiornerà automaticamente il programma.
VI. Ricarica
6.1. Spegnere la fotocamera e collegare la fotocamera a una presa di alimentazione
CA mediante l'alimentatore DC5V e il cavo USB fornito.
6.2. Entrambe le spie rosse e blu rimarranno illuminati durante il processo di carica.
6.3. Ci vorranno 40 minuti per ottenere una carica completa.
6.4. La spia rossa si spegne e il blu rimane accesa quando la telecamera è comple-
tamente carica.
VII. Ripristino
Se per qualsiasi motivo, la fotocamera smette di rispondere o non funziona corretta-
mente, eseguire un ripristino rapido ripristinerà di nuovo al normale funzionamento.
Funzionamento: Quando la fotocamera è accesa, premere il pulsante di accensi-
one e il tasto Modalità contemporaneamente una volta; la fotocamera si spegne au-
tomaticamente. Quindi è possibile riavviare la macchina fotografica con le
impostazioni predefinite di fabbrica.
VIII. Impostazioni Orario
8.1. Estrarre la regolazione dell'ora manopola fino a sentire un clic. Sia lancette delle
ore e dei minuti essere fermati.
8.2. Ruotare il tempo manopola di regolazione per impostare l'ora.
8.3. Spingere la regolazione dell'ora manopola indietro dopo il tempo impostato è
completata.
Table of contents
Languages:
Other Wiseup Security Camera manuals

Wiseup
Wiseup DVR-0031-4 User manual

Wiseup
Wiseup WIFI33 User manual

Wiseup
Wiseup WIFI40 User manual

Wiseup
Wiseup DV-07-WIFI User manual

Wiseup
Wiseup CUP200 User manual

Wiseup
Wiseup P9000 User manual

Wiseup
Wiseup WIFI38 User manual

Wiseup
Wiseup P3021 User manual

Wiseup
Wiseup WIFI37 User manual

Wiseup
Wiseup CK6000 User manual

Wiseup
Wiseup U11 User manual

Wiseup
Wiseup T183 User manual

Wiseup
Wiseup MT-V8 User manual

Wiseup
Wiseup WIFI28 User manual

Wiseup
Wiseup T186 User manual

Wiseup
Wiseup BC303 User manual

Wiseup
Wiseup WI-FI 21 User manual

Wiseup
Wiseup H200 User manual

Wiseup
Wiseup WIFI34 User manual

Wiseup
Wiseup WIFI04S User manual