Metalcraft 2614WT User manual

2614WT/2814WT OWNERS MANUAL
Ph:(478)-6251225 4620 Horseshoe Rd. Louisville, GA 30434

Louisville, GA 30434
Phone: [phone]
Fax: [phone]
www.MetalcraftScrapers.com
We at Metalcraft would like to express our gratitude for choosing
our company to help you to be productive and successful.
Metalcraft of Ga, Inc. is committed to your satisfaction with our
equipment and services. Please review this manual and learn about
your equipment. This machine is the culmination of many years of
experience in the scraper business.
As we continually strive to improve and stay at the forefront of our
industry, we sincerely appreciate your suggestions.
Thank You
Metalcraft

Daily Walk Around Inspection
For maximum service life, performance, and safety each machine
should be inspected daily before operation.
Perform a general walk around looking for missing or loose bolts,
hydraulic leaks, structural damage or cracks, and build up of trash or
material on the machine. Repairs should be made before continued
operation of the machine.
In addition these specific areas should checked:
1) Tires should be checked for damage and proper inflation.
The proper inflation is 60psi for bias tires.
2) Check all hitch, tongue, and floor bolts.
3) Check all tire nuts and studs.
4) Check tire oscillator bolts and bearings.
5) Check hydraulic lines and hoses for wear or damage.
Replace or repair as necessary.
6) Check hitch and tongue area for cracks, damage or unusual
wear. Repair as necessary.
7) Grease all swivel hitch points daily.
8) Check ejector wear blocks for excessive wear and loose
bolts.
9) Check all pins for loose or damaged retainers.
10) Check blades and router bits for excessive wear.
Operating Techniques
1) Swivel hitch may be adjusted or front assembly rotated for
creating the desired blade angle.
2) When top loading the scraper bowl must be completely
lowered to the ground. Keep in mind that the weight of
excavator loaded material is heavier than that loaded by a
scraper. Weight capacity is scraper heaped rating x 2400.

Maintenance Section
If maintenance/welding is required check with Metalcraft for product
updates or for proper procedures.
Where possible all fasteners on Metalcraft scrapers are grade 8.
When replacing fasteners use grade 8 or better.
Bias tires should be inflated to 60 psi.
Maintenance Schedule
When Required
Replace cutting edges and router bits.
Replace or adjust ejector wear blocks and rollers.
Daily
Walk around inspection.
Lubricate hitch.
Every 50 Hours or Monthly
Check tire inflation.
Every 250 Hours or Monthly
Check and grease wheel bearings.
Check and grease oscillator bearings.
Check hitch for wear.
Check all pivot bushing for wear.
Every 2000 Hours or Yearly
Repack wheel bearings.
Repack oscillator bearings.
Note: Only perform maintenance after park brake has been set
and wheels are properly chocked. Always use safety lock out
valves on cylinders and use proper blocking techniques when
performing any maintenance on your machine.

Warranty Policy
The Purpose of the Warranty
Metalcraft of Georgia, Inc. warrants each new product to be free from
defects in material and workmanship. This warranty is applicable for
products or components, not to exceed one year from the date of
delivery of the new Metalcraft product to the original purchaser, or the
date the product is first put into service via a rental agreement or
other means, whichever comes first.
Limited Warranty Statement
Genuine Metalcraft of Georgia, Inc. replacement parts and
components will be warranted for 30 days from date of purchase, or
the remainder of the original equipment warranty period, whichever is
longer.
Under no circumstances will it cover any merchandise or components
thereof, which in the opinion of the company, has been subjected to
misuse, unauthorized modification, alterations, an accident or if
repairs have been made with parts other than those obtained through
Metalcraft of Georgia, Inc.
Metalcraft of Georgia, Inc. in no way warrants tires since their
respective manufacturer warrants these items separately. Please call
Metalcraft of Georgia, Inc. to receive phone numbers of tire suppliers.
Metalcraft of Georgia, Inc. in no way warrants wearable items such as
cutting edges, rollers, bushings, yoke hitch pins, hitch bushings, etc.
Our obligation under this warranty shall be limited to repairing or
replacing, free of charge to the original purchaser, any part that, in
our judgement, shall show evidence of such defect, provided further
that such part shall be returned within 30 days from the date of failure
to Metalcraft of Georgia, Inc. routed through the dealer or distributor
from whom the purchase was made, transportation charges prepaid.

Upon warranty approval proper credits will be reimbursed for
transportation.
This warranty shall not be interpreted to render Metalcraft of Georgia,
Inc. liable for injury or damages of any kind or nature to person or
property. This warranty does not extend to the loss revenue, extra
labor cost associated with downtime, substitute machinery, rental, or
for any other reason.
Except as set forth above, Metalcraft of Georgia, Inc. shall have no
obligation or liability of any kind on account of any of its equipment
and shall not be liable for special or consequential damages.
Metalcraft of Georgia, Inc. makes no other warranty, expressed or
implied, and, specifically, Metalcraft of Georgia, Inc. disclaims any
implied warranty or merchantability or fitness for a particular purpose.
Some states or provinces do not permit limitations or exclusions of
implied warranties or incidental or consequential damages, so the
limitations or exclusion in this warranty may not apply.
This warranty is subject to any existing conditions of supply which
may directly affect our ability to obtain materials or manufacture
replacement parts.
Metalcraft of Georgia, Inc. reserves the right to make improvements
in design or changes in specifications at any time, without incurring
any obligation to owners of units previously sold. No one is
authorized to alter, modify or enlarge this warranty nor the exclusion,
limitations and reservations.
Dealer Responsibilities
The following responsibilities are to be performed when the dealer
delivers a product to the purchaser or otherwise places it into
warranty services:
- Review the warranty statement and operator’s manual with
purchaser to assure understanding of purchaser’s
responsibilities as related to warranty, service, and the proper
and safe operation of the product. Purchasers/Renters should
be advised to have failed parts repaired or replaced
immediately upon failure, as continued use will result in
additional damage, excessive wear, and may result in personal
injury.

- Contact Metalcraft of Georgia, Inc. prior to beginning repair or
replacement of failed parts to make certain that the cost of
repairs is consistent with the value of the product being sold.
Reimbursement for parts used in warranty repair will be
credited only when parts are purchased from Metalcraft of
Georgia, Inc. and will be credited at dealer’s net cost. No
warranty will be allowed on parts that are past due. The use of
parts from other sources will not be eligible for warranty
consideration.
- Dealer should use parts from their inventory first. If parts must
be shipped from Metalcraft of Georgia, Inc. freight will be paid
by Metalcraft and will be shipped by the most economical
means to arrive in the shortest possible time. Air, Next Day Air,
Priority and other special shipment methods requested by the
dealer or customer will be at customer’s expense.
Reimbursement for labor to the dealer is made by payment of
the established hourly shop rate. Labor is not paid on the
warranty associated with repair parts purchased by the retail
customer that are used on a product that is not currently in
warranty time frame. Outside repair (not dealer personnel)
invoices must have prior approval from Metalcraft of Georgia,
Inc. and must be attached to the warranty claim after approval.
- Warranty requests for units in dealer’s inventory may be
submitted to Metalcraft Of Georgia, Inc. when defects are noted
in products prior to the retail sale or rental of that unit.
- Provide warranty and service repairs as directed by Metalcraft
of Georgia, Inc.’s Service Repairs Bulletins or other
instructions. Service Bulletins will be issued when necessary to
alert dealers of special repairs.
- All warranty work must be completed within 30 days of failure.
Notify Metalcraft of Georgia, Inc. warranty department if repairs
will require more than 30 days after failure for an extension. No
claim will be accepted for warranties that exceed this 30-day
period.
- In all cases, the most economical repair should be performed.
Credit will not be allowed for assemblies if it is practical to make
repair with individual parts. In some cases, the assembly price
may be less than the total of the parts and labor required to
complete the repair. In those cases, an assembly may be used.
- No warranty will be allowed on units delivered to the retail
customer prior to the full payment of that unit to the
manufacturer by the dealer.

- If diagnostic time is required, contact Metalcraft of Georgia, Inc.
prior to beginning the warranty repair for approval. Metalcraft
must approve travel time reimbursement prior to beginning the
warranty repair.
- All dealers will warranty their technician’s work to the purchaser
and will indemnify Metalcraft of Georgia, Inc. from such claims.
- Warranty reimbursement is NOT possible when failure falls
under the “limitations” as identified in the Limited Warranty
Statement or on claims, due to damage or shortage that are
obviously the responsibility of the dealer or delivering carrier or
on the entire claim when warranty policy and provisions are not
followed.
- Dealers will be notified of a denied claim in writing and will state
the reason for denial. A dealer has a right to appeal this claim
within 30 days of denial. If there is no appeal the claim will be
considered closed.