Metalcraft TFA11 User manual

ATV trailer with Linear Actuator
TFA11

Specific Warnings and Precautions for the linear actuator
1. Read through and understand the manual before using the linear actuator.
2. Connect the plug with an ATV or UTV trailer to make the linear actuator work.
3. Make sure the motor has fully stopped before changing directions. If you change directions when the motor is running,
it may damage the motor.
4. Do not attempt to extend or retract linear actuator by hand. This could damage the actuator.
5. Do not exceed the rated load capacity (Maximin 1200kg) of the linear actuator.
ASSEMBLY INSTRUCTIONS
Tools needed – An adjustable wrench
IMPORTANT ASSEMBLY TIP: Do not tighten any nut and bolt combinations completely until all parts are assembled
together! Finger tighten plus one turn of a wrench only! This will temporarily hold the lock nut on the bolt while helping
alignment of all parts! After all parts are assembled together, all nut & bolt combinations must be completely tightened.
1. Install the frame and shaft together, using 2-M12*70 bolt,2-M12 nut, 2-M8*30bolt,2-M8 nut,2-⌀8 washer, ⌀8 spring
washer, 2-⌀5*50 pin roll “R” dowel pin, then flip the frame, installation the tires, make the nozzle outside，and tighten
with 16-M12 wheel hub nut, tighten all the bolt & nuts. Mount the rob, using 2-M16*50 bolt,2-M16nut. Install the
capacitor plate, using 4-M8*20 bolt 4-, M8 nut.
SEE FIGURE 1.

2. Install the net frame &the jack, then install the stanchion, using 2-M12*70 bolt, M12nut. Tighten the nut after adjusting
to the appropriate position. Install the linear actuator, using ⌀12* 70bolt M12 nut, Install the tool box with 2 -⌀6 * 20
bolt, M6 nut. SEE FIGURE 2.

3. Install the box, using 2- M18*80 pin roll, 2-“R” pin,2-M16 nut, Install the linear, using 12* 70 bolt M12 nut with the box.
Install the door panel and fasten it. SEE FIGURE 3.
4. Install the fence, using 6-M8*30 bolt, M8 nut, fasten the fence. SEE FIGURE 4.

5. Install the crane, using 2-M14*140 bolt, M14nut, install the rotating parts with the hanger, using M20 nut, ⌀20 washer,
⌀20washer, ⌀16spring, adjust the chain length, using 2-D pin. Install the rotating parts, using 2- M10*80 bolt, 2-M10 nut,
2-⌀10 washer, 2-⌀10 spring washer, 2-⌀16 bolt sleeve. Install the tool box with 2 -⌀6 * 20 bolt, M6 nut.
SEE FIGURE 5.
WARNING
READ, UNDERSTAND AND FOLLOW ALL ASSEMBLY, INSPECTION, MAINTENANCE & USE INSTRUCTIONS
PROVIDED BEFORE EACH USE. FAILURE TO FOLLOW ALL WARNINGS AND INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH.
DOUBLE CHECK THE ASSEMBLY OF YOUR TRAILER TO BE SURE YOU ASSEMBLED IT CORRECTLY AND ALL
NUTS & BOLTS ASSEMBLIES ARE TIGHTENED BEFORE INITIAL USE.
BE SURE TO PERIODICALLY CHECK ALL NUTS AND BOLTS FOR TIGHTNESS. OVER TIME, NUTS AND BOLTS
MAY BECOME LOOSE FROM VIBRATION.
BE SURE TO ALWAYS HAVE THE CORRECT AMOUNT OF AIR PRESSURE IN TIRES. THIS WILL HELP DETER
FROM UNNECESSARY WEAR AND/OR DAMAGE. AIR PRESSURE CAN BE FOUND ON SIDEWALL OF TIRE.
NEVER DRIVE ON HILLY TERRAIN - EXCESSIVE WEIGHT CAN CAUSE WEIGHT SHIFTS WHICH CAN LEAD TO
LOSS OF CONTROL OF YOUR ATV AND/OR ATV TRAILER.
DO NOT DRIVE IN EXCESS OF 10 MPH WHILE USING THIS PRODUCT.
NEVER ALLOW PEOPLE OR ANIMALS TO RIDE IN THE ATV TRAILER! IT IS NOT DESIGNED FOR THAT MATTER.
USE CAUTION NEAR TRAILER TILT LATCH. BE SURE LATCH IS ENGAGED BEFORE EACH USE.

Never…
•Use excessive speed while towing trailer.
•Exceed the maximum load capacity of 1200KGS.
•Allow people or animals to ride in trailer.
•Use on hilly terrain.
•Use a damaged product.
•Use when intoxicated or using over-the-counter medication or prescription drugs.
•Use on rocky or obstacle ridden terrain.
•Use carelessly -- Think Safety!
This item is designed for certain application only. The distributor cannot be responsible for issues arising from
modification. We strongly recommend this item not be modified and /or use for any application other than that for which
it was designed.
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible
conditions or situations that could occur. It must be understood by the operator that common sense and caution are
factors which can't be built into this product, but must be supplied by the operator.

A11 ATV trailer Part List
NO.
DESCRIPTION
QTY
1
M12 wheel hub nut
1
37
M8*20
1
2
M12 wheel hub nut
1
38
Ø18*80 pin roll
1
3
M12 wheel hub nut
1
39
"R" pin
1
4
M12 wheel hub nut
1
40
Ø18*80 pin roll
1
5
M12 wheel hub nut
1
41
"R" pin
1
6
M12 wheel hub nut
1
42
M12*70 bolt
1
7
M12 wheel hub nut
1
43
M12 nut
1
8
M12 wheel hub nut
1
44
Ø8*30 bolt M8 nut
1
9
M12 wheel hub nut
1
45
Ø8*30 bolt M8 nut
1
10
M12 wheel hub nut
1
46
Ø8*30 bolt M8 nut
1
11
M12 wheel hub nut
1
47
Ø8*30 bolt M8 nut
1
12
M12 wheel hub nut
1
48
Ø8*30 bolt M8 nut
1
13
M12 wheel hub nut
1
49
Ø8*30 bolt M8 nut
1
14
M12 wheel hub nut
1
50
M14 nut
1
15
M12 wheel hub nut
1
51
M14 nut
1
16
M12 wheel hub nut
1
52
M14*140 bolt
1
17
Ø5*50 dowel
1
53
M14*140 bolt
1
18
Ø5*50 dowel pin
1
54
M6 nut
1
19
M8*30 bolt
1
55
M6 nut
1
20
Ø8 washer
1
56
M6*20 bolt
1
21
Ø8 spring washer
1
57
M6*20 bolt
1
22
M8 nut
1
58
D-pin
1
23
Ø5*50 dowel pin
1
59
D-pin
1
24
Ø5*50 dowel
1
60
M20 nut
1
25
Ø8 washer
1
61
Ø16 spring
1
26
Ø8 spring washer
1
62
Ø8 washer
1
27
M8*30 bolt M8 nut
1
63
"R" pin
1
28
M16*50 bolt M16
nut
1
64
M10*90 bolt
1
29
M16*50 bolt M16
nut
1
65
Ø8 washer
1
30
Ø8*20 bolt M8 nut
1
66
Ø8 spring washer
1
31
Ø8*20 bolt M8 nut
1
67
M10 nut
1
32
Ø8*20 bolt M8 nut
1
68
M10*90 bolt
1
33
Ø8*20 bolt M8 nut
1
69
Ø8 washer
1
34
M12*70 bolt
1
70
Ø8 spring washer
1
35
M12 nut
1
71
M10*10 nut
1
36
M8*20
1