Meyer 31125 User manual

CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
125 LB. ATV SPREADER
OWNERS
MANUAL
Model No.
31125
Assembly
Operation
Maintenance
Repair Parts

2
RULES FOR SAFE OPERATION
Any power equipment can cause injury if operated improperly or if the user does not understand how to operate
the equipment. Exercise caution at all times when operating equipment.
LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT
MEANS — ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED.
CARTON CONTENTS
1. Hopper/Frame Assembly
2. Vinyl Cover
3. Impeller Shaft
4. Impeller
5. Motor Mount Assembly
6. Mounting Bracket, R.H.
•Read this owners manual before attempting to assemble
or operate the spreader.
•Read the vehicle owners manual and know how
to operate your vehicle, before using the spreader
attachment.
•Do not allow anyone to ride on or sit on spreader
attachment frame.
•Never allow children to operate the vehicle or spreader
attachment.
•Do not allow adults to operate the vehicle or spreader
attachment without proper instructions.
•Never operate vehicle and spreader attachment without
wearing solid, substantial footwear.
•Wear eye and hand protection when handling and using
lawn chemicals.
• Always begin with the transmission in rst (low) and
gradually increase speed as conditions permit.
•When using broadcast spreader do not drive too close
to a creek or ditch and be alert for holes and other
hazards which could cause you to loose control of the
broadcast spreader and vehicle.
•Always operate vehicle and spreader up and down a
slope, never across a slope.
•Read instructions and caution notes for handling and
application of materials purchased for spreading.
•Follow maintenance and lubrication instructions as
outlined in this manual.
7. Mounting Bracket, L.H.
8. Wire Harness
9. Deector
10. ExtensionBrackets(2)
11. Shield
1
3
5
4
9
2
10
11
67
8

3
SHOWN FULL SIZE
NOT SHOWN FULL SIZE
HARDWARE PACKAGE
A C E
M
L
F G H
P
J
I
K
R S
X
YZ
W
T
U
V
O
N
Q
D
B
REF QTY DESCRIPTION
A 4 Hex Bolt, 5/16 x 2-3/4"
B 4 Hex Bolt, 5/16 x 2"
C 4 Hex Bolt, 5/16" x 1"
D 2 Hex Bolt, 1/4 x 3/4"
E 6 Hex Bolt, 1/4 x 1"
F 1 Carriage, 5/16" x 1"
G 5 Carriage Bolt, 5/16" x 1-3/4"
H 2 Carriage Bolt, 1/4-20 x 3/4"
I10 Nylock Hex Nut, 1/4"
J12 Nylock Hex Nut, 5/16"
K 4 Flat Washer , 1/4"
L 8 Flat Washer, 5/16"
M 8 Nylon Washer
REF QTY DESCRIPTION
N 1 Hair Pin Agitator
O 2 Cotter Pin, 1/8" x 1-1/4"
P 4 Hair Pin, 3/32 x 1.4"
Q 1 Coupler
R 4 Swivel Bracket
S 4 Adhesive Pad
T 2 Plug
U 3 Nylon Tie
V 5 Plastic Knob (2 Handle)
W 5 Mounting Clamp
X 4 Bent Clevis Pin
Y 2 Plastic Knob (3 Handle)
Z 2 Angle Stop Bracket

4
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED FOR ASSEMBLY
(1) Pliers
(2) 7/16"Wrenches
(2) 1/2"Wrenches
(2) 9/16"Wrenches
REMOVAL OF PARTS FROM CARTON
Remove all parts and hardware packages from the carton.Lay
out all parts and hardware and identify using the illustrations
on pages 2 and 3.
FIGURE 1
FIGURE 2
1. Turn the spreader upside down and press the two plugs
into the ends of the frame tube.
HINT: Use a block of wood to help press the plug down
into the end of the tubing.
2. Fastenthedeectortotheanglebracketsusingtwo1/4"
x3/4"hexbolts,1/4"atwashersand1/4"nylocknuts.
Allowtheanglebracketstoswivelsothatthedeector
curves naturally between the angle brackets.
1/4" NYLOCK
NUT
1/4" FLAT
WASHER
1/4" x 3/4"
HEX BOLT
DEFLECTOR
3/32" HAIR PIN
BENT CLEVIS PIN
MOUNTING
BRACKET, R.H.
FIGURE 3
NOTE:Thetopofthehoppershouldbeatleast30"above
theground.Themountingholesshowningures3and4
will make the top of the hopper even with the vehicle's rear
rack. If exhaust blows against spreader, a higher mounting
position may help.
Position the spreader for adequate clearance if
thevehiclemuferdischargesstraighttoward
the rear.
IMPORTANT: Before proceeding, determine if the mounting
brackets, when attached directly to the spreader frame, will
tontothevehiclerack.Iftheyneedtobefartherapart,use
theextensionbracketsingure4.
If you are NOT using extension brackets:
3. Attach the R.H. mounting bracket to frame tube using
twobentclevispins and3/32"hair pinsasshownin
gure3.Tighten. Repeat for the L.H.mounting bracket.
PLUG

5
If you are using extension brackets:
4. Attach the extension brackets to the legs of the spreader
frame.Usetwo5/16"x2"hexboltsand5/16"nylock
nuts per bracket. Tighten.Seegure4.
5/16" NYLOCK
NUT
MOUNTING
BRACKET, R.H.
5/16" x 2-3/4"
HEX BOLT
If you are using extension brackets:
5. Attach the R.H.mounting bracket to the extension bracket
showningure5usingtwo5/16"x1"hexboltsand
5/16"nylocknuts.Tighten. Repeat on the other frame
leg with the L.H. mounting bracket.
FIGURE 5
FIGURE 6
FIGURE 4
5/16" x 2"
HEX BOLT
EXTENSION
BRACKET
5/16" NYLOCK NUT
6. Attach an angle stop bracket and a swivel bracket to
the rear hole in the R.H. shield bracket using a 1/4"
x 1" hex bolt, two 1/4" washers, a nylon washer and
a 1/4" Nylock nut. Place the angle stop bracket on
inside and swivel bracket on outside. Tighten locknut
so the swivel bracket can pivot freely. See gure 12.
Repeat step on L.H. shield bracket.
7. Attach a swivel bracket to front hole in the R.H. shield
bracket using a 1/4" x 1" hex bolt, two 1/4" washers,
a nylon washer and a 1/4" Nylock nut. Tighten the
nut so that the swivel bracket can pivot freely. See
gure 12. Repeat step on L.H. shield bracket.
SWIVEL
BRACKET
ANGLE STOP
BRACKET
1/4" x 1"
HEX BOLT
1/4"
WASHER
1/4" NYLOCK
NUT
NYLON
WASHER
SHIELD
BRACKET
NYLON
WASHER
8. Assemble spreader shield to the front swivel brackets
using two 1/4" x 3/4" carriage bolts, 1/4" washers and
the two 1/4" plastic knobs. See gure 13.
9. Assemble spreader shield to the rear swivel brackets
using two 1/4" x 1" hex bolts, four 1/4" washers and
two 1/4" Nylock nuts. Tighten the nuts so that the
swivel bracket can still pivot freely. See gure 13.
FIGURE 7
1/4" x 1"
HEX BOLT
1/4" WASHER
1/4" NYLOCK NUT
PLASTIC
KNOB
1/4" x 3/4"
CARRIAGE BOLT

6
FIGURE 11
15. Place the motor assembly down into the hopper, inserting
the end of the spreader shaft into the impeller coupler.
Secureitwitha1/8"x1-1/4"cotterpin,spreadingthe
endsofthepinaroundthecoupler.Seegure9.
16. Fasten the motor mount bracket to the hopper using four
5/16"x1"hexbolts,5/16"atwashers,nylonwashers
and5/16"nylocknuts.Seegure9.
14. Assemble the impeller coupler onto the motor shaft and
secureitwiththesetscrewagainsttheatsideofthe
motorshaft.Seegure8.
FIGURE 10
SET SCREW
IMPELLER
COUPLER
5/16" x 1"
HEX BOLT
NYLON
WASHER
5/16" NYLOCK NUT
MOTOR
ASSEMBLY
5/16" FLAT
WASHER
1/8" x 1-1/4"
COTTER PIN
SPREADER
SHAFT
FIGURE 8
10. Attach the spreader's mounting brackets to the vehicle's
rear rack using four 5/16" x 1-3/4" carriage bolts,
mounting clamps and plastic knobs. Use the adhesive
padstoprotecttherack.Seegure6.
5/16" x 1-3/4"
CARRIAGE BOLT
MOUNTING
CLAMP
PLASTIC KNOB
MOUNTING
BRACKET
ADHESIVE PAD
IMPELLER
1/8" x 1-1/4"
COTTER PIN
1/8" HAIRPIN
AGITATOR SPREADER
SHAFT
FIGURE 9
11. Insertthe1/8"hairpinagitatorintothemiddleholein
thespreadershaft.Seegure7.
12. Slide the end of the spreader shaft through the plastic
bushinginthebottomofthehopper.Seegure7.
13. Slide the impeller onto the spreader shaft and secure
itwitha1/8"x1-1/4"cotterpin.Seegure7.

7
FIGURE 13
FIGURE 12
FIGURE 14
WIRING INSTRUCTIONS
When properly connected, the spreader motor and impeller
will run clockwise viewed from above.
18. Movethespreader'sowcontrollevertotheoffposition
sothatthe"ON-Off"switchisturnedoff.
19. Connecttheshort(fused)wireharnesstothevehicle
battery by connecting the red wire to the positive post
and the brown wire to the negative post on the battery.
The wire harness may be left permanently attached to
thebattery.Seegure12.
20. Connect the long wire harness to the spreader by
connecting the red and white wires to the switch and
the brown and white wires to the spreader motor. Refer
togure12.
21. Connectthelongwireharnesstotheshort(fused)wire
harness.Be sure the wires are clear of any moving parts,
hot engine parts, or pinch points.
22. Use the nylon ties provided to safely secure the wiring
away from hot engine parts, rotating parts and pinch
points.
17. Attachtheowcontroltothemotormountbracketonthe
spreaderusingthe5/16"x1"carriagebolt,amounting
clampandaplasticknob.Seegure11.
NOTE:Youcanalsoattachtotherearrackifyouusea5/16"
x1-3/4"carriagebolt.Ifyouattachtotherearrack,youcan
looselypre-assembletheclamp,boltandknobtotheow
control. The clamp can then be angled down through the
slot in the rack.
NEVER allow negative pin on plug to come
incontactwithpositive"hot"postonbattery.
Fire or explosion can result!
"ON-OFF"
SWITCH
FLOW CONTROL
ON-OFF
23. Movetheowcontrollevertothe"ON"position.Flip
the "ON-OFF" switch on and check that the motor
runs counterclockwise. If it does not, refer to the wiring
diagram on page 6 and recheck the hookup.
24. Movetheowcontrolleverto"OFF".Thisshouldturn
the"ON-OFF"switchoff.Ifitdoesnot,youcanloosen
thecontrol androtate itenough thatthe owcontrol
lever,whenmovedtothe"OFF"positionwillturnthe
switchoff.Seegure13.
BROWN
RED
FUSE AND HOLDER
POSITIVE
"HOT" POST
NEGATIVE PIN
BROWN
RED
BATTERY
+
SWITCH MOTOR
BROWN
RED WHITE
5/16" x 1"
CARRIAGE
BOLT
MOUNTING
CLAMP
PLASTIC KNOB
5/16" x 1-3/4"
CARRIAGE
BOLT

8
FIGURE 16
IMPORTANT: Application rates shown in the chart are
affected by humidity and by the moisture content of
the material (granular and pellet). Some minor setting
adjustments may be necessary to compensate for this
condition.
OVERLAP
REFER
TO CHART
USING YOUR SPREADER
We do not recommend the use of any powdered lawn
chemicals, due to difculty in obtaining a satisfactory or
consistent broadcast pattern.
1. Determine approximate square footage of area to be
covered and estimate amount of material required.
2. Verify that the spreader motor turns on and off and that
theowcontrolisoperatingproperly.
3. Makesuretheowcontrolleverisintheoffposition
and the closure plate is shut.
4. Settheadjustablestoptothedesiredowrate,keeping
the ow control arm in the off position. Refer to the
application chart on this page and the instructions
onthefertilizerbagtodeterminetheproperowrate
setting. The application chart is calculated for a vehicle
speedof3mph(100ft.in23seconds).Fasterspeeds
requirehigherowratesettingstomaintainthesame
application rate.
5. Fill the hopper with the material to be spread, breaking
upanylumpsasyoullthehopper.
7. Start the vehicle in motion and then open the spreader
closureplateandiptheswitchto"ON".
OPERATION
HOW TO USE YOUR SPREADER
SETTING THE FLOW CONTROL
1. Slide the Adjustable stop to the desired setting.
2. Move the Flow Control Lever forward until it snaps into
the Adjustable Stop, locking the lever at the desired
setting.Seegure15.
5
1
3
7
10
OFF
FLOW CONTROL LEVER
ADJUSTABLE STOP
FIGURE 15
STARTING THE SPREADER
1. Move the Flow Control Lever against the Adjustable
Stopandipthe"ON-OFF"switchtotheonposition.
STOPPING THE SPREADER
1. MovetheFlowControlLevertothe"OFF"position.Make
sure that the switch is turned off by the Flow Control
Lever.
8. Shut the closure plate before turning or stopping.
9. To insure uniform coverage, make each pass so that the
broadcast pattern slightly overlaps the pattern from the
previouspassasshowningure16.Theapproximate
broadcast widths for different materials are shown in
the application chart on this page.
10. When broadcasting weed control fertilizers, make sure
the broadcast pattern does not hit evergreen trees,
owersorshrubs.
11. Heavy moisture conditions may require a cover over the
hopper to keep contents dry. The vinyl cover acts as a
wind and moisture shield, but should not be used as a
rain cover.
12. If fertilizer is accidentally deposited too heavily in an
area, soak the area thoroughly with a garden hose or
sprinkler to prevent burning of the lawn.
TYPE FLOW SETTING SPREAD
MATERIAL 3 MPH WIDTH
FERTILIZER
Powder 3 - 5 3' - 4'
Granular 3 - 5 10' - 12'
Pelleted 3 - 5 17' - 19'
Organic 6 - 8 3' - 4'
GRASS SEED
Fine 3 - 4 3' - 4'
Coarse 4 - 5 8' - 9'
ICE MELT 6 - 8 17' - 19'
SAND 4-10 17' - 19'
APPLICATION CHART
OPERATING SPEED -3MPH.(100ft.in23seconds)

9
MAINTENANCE
CHECK FOR LOOSE FASTENERS
1. Before each use make a thorough visual check of the
spreader for any bolts and nuts which may have loosened.
Retighten any loose bolts and nuts.
CHECK FOR WORN OF DAMAGED PARTS
2. Check for worn or damaged parts before each use.
Repair or replace parts if necessary.
CLEANING
3. Rinse inside of hopper and exterior of spreader and dry
off before storing.
STORAGE
1. Rinse inside of hopper and exterior of spreader and dry
off before storing.
2. Store in a clean, dry area.
TROUBLE SHOOTING POINTS
1. Material packed around plate
1. Loose connection in spreader
wiring
2. In line fuse is blown.
3. Loose battery connection
4. Battery is run down.
5. Broken spreader wiring
6. Spreader switch is broken.
7. Spreader motor is broken.
1. Wired backwards to battery.
1. Wired backwards to battery.
2. Spreaderon-offswitchisbroken.
Hopper closure plate does not open to
the correct position.
Spreader motor doesn't run.
Spreader motor runs backwards.
Motor runs when switch is shut off.
1. Clean out around closure plate
1. Check and reconnect.
2. Replace fuse.
3. Tighten battery terminals.
4. Recharge the battery.
5. Replace damaged wiring.
6. Replace the switch
7. Repair or replace motor.
1. Switch wiring at battery terminals.
1. Switch wiring at battery terminals.
2. Replace the switch.
REMOVING THE SPREADER
13. Disconnect the spreader from the vehicle battery by
unplugging the short wire harness from the long wire
harness.The short wire harness may be left permanently
attached to the battery.
14. Removetheowcontrolfromtherearrackofthevehicle
if it is attached there.
15. Loosen the knobs on the spreader mounting brackets.
Rotate the clamps fastened underneath the vehicle
rack and lift them up through the rack to remove the
spreader.

10
REPAIR PARTS FOR ATV MOUNTED
125 LB. BROADCAST SPREADER MODEL 31125
38
59
35
36
34
39
58
41
22
25 4
6
5
55
3
6
5
20
33
1
7
7
7
27
47
46
7
24
26
9
8
31
5
37
42
40
45
30, 51
29
12
14
13
15
11
40
56
5
5
54
6
21
6
6
6
54
21
6
55 7
7
7
52
28
16
36
10
2
6
19
17
27
30
29
28
49
48
18 43
44
22
23
23
22
57
50
32
53

11
REF PART NO QTY DESCRIPTION
1 AF41935 1 Hopper
2 AF48402 2 Plastic Plug
3 AF45164 2 Hex Bolt, 1/4-20 x 2-1/4"
4 AF46699 4 Hex Bolt, 1/4-20 x 2"
5 AF1543-69 14 Nylon Washer
6 AF43088 14 Flat Washer, 1/4"
7 AF47189 16 Nylock Nut, 1/4-20
8 AF25118 1 Flow Slide
9 AF24853 1 Guide Plate
10 AF41157 4 Rivet, Stainless Steel
11 AF47999 1 Control Cable Assembly
12 AF24937 1 Control Mount Bracket
13 AF46978 1 Hex Nut, 1/4-20 (SIMS)
14 AF48983 1 Switch, On-Off
15 AF44732 1 Star Washer
16 AF45082 1 Boot, Rubber Switch
17 AF48947 1 Tube, Hopper Mount
18 AF44180 4 Hex Bolt, 5/16-18 x 2"
19 AF726-0178 3 Nylon Tie
20 AF48934 1 Hairpin Agitator
21 AF43661 6 Hex Bolt, 1/4-20 x 1"
22 AF47810 8 Nylock Nut, 5/16-18
23 AF25248 2 Extension Bracket
24 AF43012 2 Hex Bolt, 1/4-20 x 3/4"
25 AF24946 1 Impeller Shaft
26 AF47674 2 Plug, 1-1/4"
27 AF23826 2 Angle Bracket
28 AF43720 5 Plastic Knob (2 handle)
29 AF23442 5 Mounting Bracket
30 AF44215 5 Carriage Bolt, 5/16-18 x 1-3/4"
REF PART NO QTY DESCRIPTION
31 AF43063 4 Hex Bolt, 5/16-18 x 1"
32 AF43081 4 Flat Washer, 5/16"
33 AF44285 1 Bushing, Hopper
34 AF41976 1 Coupler, Impeller
35 AFHA115321 1 Set Screw
36 AF43010 2 Cotter Pin, 1/8" x 1-1/4"
37 AF46554 1 Wire Harness
38 AF24936 1 Bracket, Motor Mount
39 AF41931 1 Motor with fasteners
40 AF24125 2 Shield Bracket
41 AF736-0722 4 Lock Washer, #10
42 AF46119 1 Spreader Shield
43 AF41934 4 Bent Clevis Pin
44 AF43055 4 Hair Pin, 3/32 x 1.8"
45 AF43849 2 Plastic Knob (3 handle)
46 AF04367 1 Impeller
47 AF48559 1 Deector
48 AF25214 1 Mounting Bracket, R.H.
49 AF25213 1 Mounting Bracket, L.H.
50 AF49080 1 Vinyl Cover
51 AF44326 1 Carriage Bolt, 5/16 -18 x 1"
52 AF45039 1 Carriage Bolt, 1/4-20 x 1-3/4"
53 AF48661 4 Adhesive Pad
54 AF23998 4 Shield Swivel Bracket
55 AF23999 2 Angle Stop Bracket
56 AF44950 2 Carriage Bolt, 1/4-20 x 3/4"
57 AF1509-170 4 Hex Bolt, 5/16-18 x 2-3/4"
58 AF41975 1 Motor Cover
59 AF41994 1 Warning Label
REPAIR PARTS FOR ATV MOUNTED
125 LB. BROADCAST SPREADER MODEL 31125

Meyer Products LLC warrants to Purchaser the following:
Meyer Products LLC, warrants to the original purchaser for a period of one year from the date of purchase of Meyer® brand
spreader products that they will be free from defects in materials or workmanship, with the exceptions stated below. No
person is authorized to change this warranty or to create any additional warranty on Meyer® products.
Meyer Products LLC will repair any product that proves to be defective in materials or workmanship. In the event repair is not
possibleorpractical(asdeterminedbyMeyerProductsLLCinitssolediscretion),MeyerProductsLLCwilleitherreplacethe
product with a new product of similar model and price, or refund the full purchase price, as determined by Meyer Products
LLC. Customer must keep the complete spreader system serviced/maintained as recommended by Meyer Products LLC.
This warranty does not cover:
•Problemscausedbyfailuretofollowtheproductinstructions,orfailuretomaintaintheproductasdescribedintheOperator’s
Manual;
• Damageresultingfromrust,corrosion
• Damagecausedbyusagethatisnotinaccordancewithproductinstructions(useofthespreaderforanypurposeother
thanspreadingapprovedmaterialisconsideredmisuseandabuse);
• Anyspreader,oranypart,component,orassemblythereof,whichhasbeenmodiedoraltered;
• Problemscausedbyusingaccessories,parts,orcomponentsnotsuppliedbyMeyerProductsLLC;
• Costoftax,freight,transportationorstoragecharges,environmentalcharges,solvents,sealants,lubricantsoranyother
normal shop supplies.
• Problemscausedbycollision,re,theft,vandalism,riot,explosion,lightning,earthquake,windstorm,hail,water,ood,or
any other Acts of God;
• Liabilityfordamagetoproperty,orinjuryto,ordeathofanypersonarisingoutoftheoperation,maintenanceoruseofthe
covered product;
• Productswithmissingoralteredserialnumbers;
How To Get Service:
• Itistheresponsibilityoftheoriginalpurchasertoestablishthewarrantyperiodbyverifyingtheoriginaldeliverydate.Abill
of sale, cancelled check or some other appropriate payment record may be kept for that purpose. It is recommended, but
not required, that the consumer verify the original delivery date by immediately returning the attached Warranty Registration
Card.
How State Law Applies:
Thiswarrantygivesyouspeciclegalrights,andyoumayalsohaveotherrightswhichvaryfromstatetostate.
WARRANTY
Meyer Products LLC
18513 Euclid Ave. • Cleveland, Ohio 44112-1084
Phone [phone] (Area Code 216)
www.meyerproducts.com• email info@
meyerproducts.com
PRINTEDINU.S.A. FORMNO.41933(04/18/11)
Meyer Spreaders are protected by one or more of the following patents: 6698997, CA 2,415,540 C, 7588195, 8448882, 8505837, 8523086,
8657208, 6186731, 6,793,154 B2, 6722590, 6715703, 6978952, 6932287, 8505838, 8827002, 5842649, CA 2,435,106 C, 6364598.