meyland-smith Meywalk 4 User manual

sling seat
meywalk®4 ∙ meywalk®2000 ∙ miniwalk®
meywalk®2000
meywalk®4
miniwalk®
Installation Instructions

Mounting of cross bar on miniwalk and meywalk®2000
miniwalk and meywalk 2000 consist of a top and
boom part. To use the sling seat, replace the
seat bar (A) with the cross bar (B).
Start liing the top o from boom part. Lay the
top part on a at surface on a blanket to avoid
scratches.
Then loosen the lower allen bolt and lower
spanner grip on both sides. Use the largest of the
allen keys to loosen the allen bolt.
B cross bar
A seat belt
Remove the internal height
adjustment tube, allen bolt
and spanner grip
Mount the new cross bar
with the same parts as
used for the seat bar. Then
ghten spanner grips and
allen bolts
Tighten all allen bolts and
spanner grips
Loosen the two cones on
each side and remove the
seat bar
Reassemble the internal
height adjustment tube,
allen bolt and spanner grip
as shown in the picture
the allen key is
located in the saddle
conus
allen key
spanner grip
conus
spanner grip
3a-b
Loosen the two cones further and separate
the handle bar from the seat bar
4a-b
Aach the cross bar (B) to the handle
bar and ghten the two cones
8
Li the top of
the walker back
into place
Then follow the 8 steps as shown below
1 5 72 6

Mounting of bracket on sling seat on meywalk®4
To use the sling seat, the seat bar (A) must
be removed.
This is done by loosening the lower of the
handles on the center box.
B sling seat bracket
A seat bar
Place one part of the clamp onto the threaded holes
on the bracket (as shown on the picture)
Then follow the 3 steps as shown below
allen bolt
12 pcs
clamp
6 pairs
allen key
( located in the saddle)
loosen the lower
handle
threaded hole
Now mount the sling seat bracket on
each side of the walker using clamps
and allen bolts. Make sure they are at
the same height.
Included:
How to mount the sling seat
1 2 3
Now both brackets are mounted and are
in the same height. CHECK THAT ALL
BOLTS ARE TIGHTENED!

sling seat
Meyland-smith A/S
Mads Clausens Vej 1
DK-9800 Hjørring
telefon: [phone]
e-mail: [e-mail]
web: www.meyland-smith.dk
Item number
meywalk 4® micro 011804
meywalk 4® mini 011805
(incl. brackets)
meywalk 4® small
meywalk 4® medium (red) 011800
(incl. brackets)
meywalk 4® large (black)
meywalk 2000® medium
104790
(incl. brackets)
meywalk 2000® large
meywalk 2000® small
miniwalk® (size 1) 106086
(incl. brackets)
miniwalk® (size 2)
The sling seat is available for the following mo-
dels:
The sling seat is mounted on the front of the cross bar with the two
straps
2.
The two rear straps of the sling seat are passed be tween the user’s
legs and put on the two arms of the cross bar
3. 4.
5.
Adjust the height of the sling seat and make sure that the two front
buckles are locked and the rear straps secured on the cross bar.
6.
1.
Mounting sling seat on
miniwalk and meywalk 2000
A
Secure the two front buckles before the
user enters the walker (1.)
B
Place the user in the walker (2.)
C
Perform the rest of the mounng as shown
(3.-5.)
D
Adjust the straps so that the sling seat is
loose and not ght around the behind of the
user (6.)