MGE UPS Systems Pulsar EX10Rack User manual

Pulsar EX Rack : 86-153522-00
MGE UPS SYSTEMS
User Manual
PulsarTM
EX10 Rack / EX15 Rack
EXB10 Rack
!
…
–
+
–
+
…
………
%
%
www.mgeups.com

Pulsar EX Rack : 86-153522-00 MGE UPS SYSTEMS
Thank you for purchasing the EX Rack
Uninterruptible Power Supply.
The EX Rack has been designed to
provide many years of trouble-free
operation.Please review the manual
which has been prepared to provide
you with all the necessary information
concerning the installation and use of
your EX Rack .
For service call 1-800-523-0142.
Sincerely,
MGE UPS SYSTEMS
Federal Communications
Commission (FCC) Statement
Note: this equipment has been tested and
found to comply with Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when equipment is operated in
a residential environment. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and
used in accordance with the instruction
manual, may cause harmful interference to
radio communications. Properly shielded
and grounded cables and connectors must
be used in order to meet FCC emission
limits.
Revision A00 ECN - 000071

MGE UPS SYSTEMS Pulsar EX
Rack : 86-153522-00 i
IMPORTANT SAFETY INSTRUCTIONS
SAVETHESE INSTRUCTIONS
This manual contains important instructions for Models EX10 Rack /EX15 Rack /EXB10 Rack /EXB15 that
should be followed during installation and maintenance of the UPS batteries.
cThis equipment can be operated by any
individual, with no previous training;
cCAUTION: Risk of electric shock, even
with unit disconnected from AC power
source. Hazardous voltage still may be
present through operation from battery.
The battery supply should be disconnected
at the plus and minus terminals using the
quick disconnect connectors of the battery
when maintenance or service work inside
the UPS is necessary.
cThe UPS contains voltages which are
potentially hazardous. All repairs should
be performed by qualified service
personnel only;
cdo not attempt to power the UPS from
any receptacle other than a 2-pole 3-wire
grounded receptacle;
cdo not place Pulsar near water or in
environment of excessive humidity;
cdo not allow liquids or any foreign objects
to get inside Pulsar;
cdo not block air vents in the back of
Pulsar;
cdo not plug household appliances such as
hair dryers to Pulsar receptacles;
cdo not place Pulsar in direct sunlight or
close to heat-emitting source;
c~: alternating current supply symbol;
cCAUTION: do not dispose of battery or
batteries in a fire. The battery may explode;
cCAUTION: do not open or mutilate the
battery or batteries, released electrolyte is
harmful to the skin and eyes. It may be toxic;
cCAUTION: a battery can present a risk of
electric shock and high short circuit current.
The following precautions should be
observed when working with batteries:
vremove watches, rings or other metal
objects,
vuse tools with insulated handles,
vwear rubber gloves, boots and safety
glasses;
cplease dispose of the packaging in
accordance with the applicable laws.
cthe AC power receptacle should be near
the equipment and easily accessible. To
isolate Pulsar from AC input, remove the
input power cord from the AC power
receptacle;
cif Pulsar is to be stored for a long time, it
is recommended to recharge the batteries
(by connecting AC power source to Pulsar,
switch "ON" or "OFF"), once a month for 24
hours to avoid a full batteries discharge;
cPulsar contains batteries that should be
disposed of or recycled in accordance with
local applicable laws;
cprior to installation, store Pulsar in a dry
location;
cstorage temperatures must be between
–4°F (-20°C) and +113°F (+45°C);
cservicing of batteries should be performed
or supervised by personnel knowledgeable
of batteries and the required precautions.
Keep unauthorized personnel away from
batteries;
cwhen replacing the batteries, use the
same number and the following type of
batteries:
vPulsar EX10 Rack : 3 x 12V - 7.2Ah,
vPulsar EX15 Rack : 4 x 12V - 7.2Ah;

ii Pulsar EX
Rack : 86-153522-00 MGE UPS SYSTEMS
introduction
In critical situations, count on MGE UPS
SYSTEMS Pulsar EX10 Rack and
EX15 Rack uninterruptible power supplies
(UPS). Their protection keeps your data
intact and accessible.
Pulsar EX10 Rack and EX15 Rack UPSs
ensure top quality power around the clock,
and continue operations during power
failures. An intelligent microprocessor
detects any operating anomalies of the UPS
and triggers an alarm if corrective action is
necessary.
In addition to the high-technology aspect of
these UPSs, you can count on backup from
our staff, a team of specialists, around the
corner from you, throughout the world. It’s
no accident that MGE UPS SYSTEMS is the
world leader in UPS protection.
uses of Pulsar EX10 Rack and
EX15 Rack :
Network servers and interconnection
devices are very sensitive to electrical
disturbances of all types, including outages,
voltage sags, brownouts, spikes, etc. The
origins of the disturbances also vary, ranging
from atmospheric phenomena, to nearby
devices generating interference such as
elevators, photocopy machines and machine
tools, not to mention human errors, like the
accidental pulling out of power cords or
tripping of circuit breakers. The
consequences of these disturbances on
computer systems range from data losses to
hardware damage (power supplies, hard
disks).
Pulsar EX10 Rack and EX15 Rack are
specially designed to protect network
servers and all other devices that are
sensitive to electrical disturbances.
Pulsar EX10 Rack and EX15 Rack add fault-
tolerance to the utility supplying your
sensitive equipment.
Pulsar EX10 Rack and EX15 Rack are
designed as compact units and feature very
quiet operation.
Pulsar EX10 Rack and EX15 Rack provide a
stable supply of clean power, long back-up
time during a utility outage (see table) and
vast information and control possibilities
according to the configuration selected.
Pulsar EX10 Rack and EX15 Rack On-Line
technology provides maximum protection
and availability of your workstations, servers,
and network communication devices.
Pulsar EX10 Rack and EX15 Rack offer
many functions and characteristics designed
to simplify power management:
cautomatic battery test carried out
periodically. In the event of a fault, a LED
provides advance warning for battery
replacement;
cfront panel LEDs signal all types of faults
and alarms;
cBar graph continuously indicates the
battery charge level or the critical load power
level;
cPulsar EX10 Rack and EX15 Rack are
environment friendly: all components are
recyclable and an electronic power-saver
device reduces power consumption if the
UPS is not active for a period exceeding 5
minutes while on battery back-up;
cEX Driver software provides rapid startup
of Pulsar EX10 Rack and EX15 Rack using
the EX Tuner configuration module. This
module adapts Pulsar EX10 Rack and
EX15 Rack to user preferences (battery test
frequency, startup and shutdown
sequences, setting of battery thresholds,
etc.). See "communication" section for
further details;
cSolution-PacTM is a CD-ROM which
contains all the tools needed to supervise
your UPS.
cSimply download the EX driver utility from
the CD and Solution-Pac. The UPS must be
serialy connected to a Windows PC.

MGE UPS SYSTEMS Pulsar EX
Rack : 86-153522-00 iii
options
cUM Sensor environment measurement
unit: compatible with SNMP or Solution
PacTM, this unit measures the temperature
and the relative humidity in the room where
the Pulsar is installed. Eight relay contacts
are provided to transmit signals to an
administration platform, in the form of
voltage free contacts to enable monitoring of
(fire alarm, climate control fault, intrusion,
etc.);
cbattery extension module: Pulsar
EXB10 Rack /EXB15 battery extension
modules lengthen the battery time of the
Pulsar EX10 Rack /EX15 Rack to meet your
requirements. For rack installation of EXB15
order 19" rack kit P/N 8806U.
additional communications
options:
cSNMP administration: MGE has the
most complete offering for the administration
of a group of UPSs using the SNMP protocol
with different network-connection modules
(SNMP card or proxy software), supervision
modules (application for NMS platforms
such as HP OpenView or C.A. UNICENTER
TNG) and a file-closing module (UM Client).
cSNMP card: this card, inserted into your
UPS, can establish a direct Ethernet network
connection for your UPS. It can then be
temporarily managed using SNMP or the
various software modules of Solution-Pac.
The MGE UPS SYSTEMS offering complies
with RFC 1628 specifications (IETF) and
was certified by the InterWorking Labs
during the Test Summit in June 1994;
cstatus information card: this option
provides you with 5 voltage-free contacts: on
battery, on by-pass, low battery, load on
UPS. This card can be used with the UPS
driver of IBM AS/400.
Contact your dealer for further information
on these options.

iv Pulsar EX
Rack : 86-153522-00 MGE UPS SYSTEMS
software supplied with
Pulsar EX10 Rack and
EX15 Rack
To meet the different operating
environments of your UPS, Pulsar EX Rack
includes 2 MGE UPS SYSTEMS software
programs:
cEX-Driver software for Windows;
cNetwork based Solution-PacTM power
management software.
EX-Driver for Windows
EX Driver for Windows provides
communication with the UPS from a simple
Windows workstation. EX-Driver is
compatible with Windows 3.1x and Windows
95/98, for communication with the UPS via a
serial connection for various needs:
cpersonalization of the UPS operating
mode: the EX-Tuner utility, can be used to
change certain UPS operating parameters if
the standard factory settings are not ideal for
the operating conditions.
It is possible to modify the output voltage,
battery-test frequency, startup and shutdown
sequences, operation of automatic by-pass,
etc.;
Solution-PacTM for networks and
multi-server systems
Protection by UPS is only complete and
effective if combined with powerful software
functions which warn users and the operator
of any power supply problem, automate
system shutdown, supervise and remotely
control the UPSs. MGE UPS SYSTEMS
created Solution-PacTM for this purpose.
Solution-PacTM combines all these functions
in a single CD-ROM, usable in local or
remote mode (TCP/IP and SNMP), and
covering the main network environments.
Solution-PacTM is the ideal solution for
protecting networks and multiserver
systems.
Solution-PacTM on a single CD-ROM
contains everything needed to safeguard
one or more systems and to supervise one
or more UPSs from a local or remote station.
Solution-PacTM includes SNMP proxy
agents, system shutdown software, and
supervision software.
Solution-PacTM is a powerful and upgradable
software tool which provides all the
supervision, control and safety functions
associated with a UPS:
vgraphic display of the UPS,
vremote control of the UPS and output
receptacles,
vuser alarm of problems,
vrecording of events in log files,
vautomatic system shutdown and restart,
vlocal or remote supervision of UPSs and
ancillary devices,
vtransmission of UPS information and
alarms to any SNMP supervisor.
vpaging / e-mail capabilities
vmultiple server shutdown in
heterogeneous environment.
Platforms supported:
Windows 3.1, 95, 98, NT, Novelle Netware,
OS/2, Linus, Mac/OS, Sun Solaris, HP/UX,
IBM Aix, Dec Unix and Open VMS, Silicon
Graphics, IRIX.

Pulsar EX10 Rack / EX15 Rack / EXB10 Rack / EXB15 presentation
general contents
Pulsar presentation............................................................................................................................. 3
getting started / operation....................................................................................................... 11
Pulsar EX Rack : 86-153522-00
MGE UPS SYSTEMS 12
Pulsar EX Rack : 86-153522-00MGE UPS SYSTEMS

3MGE UPS SYSTEMS 4MGE UPS SYSTEMS
Pulsar EXB10 Rack
rear view
Pulsar EX10 Rack : 86-153522-00 Pulsar EX10 Rack : 86-153522-00
Pulsar EX10 Rack
EX15 Rack
front view
Pulsar EX10 Rack
EX15 Rack
rear view
1d
1b
1c
1f 1e
1a
2
3
!
…
–
+
–
+
…
………
%
%
18
MGE UPS SYSTEMS
ATTN: CUSTOMER SUPPORT SERVICES
1660 SCENIC AVENUE
COSTAMESA, CA 92626
PLACE
STAMP
HERE
14
17
The indispensable
companion
sofware
for your UPS
L'indispensable
complément
logiciel
de votre onduleur
solution-pac 98
19
BATTERYCONNECTOR
Volt:36Vdc = 20A
21 22 20
23
DC BREAKER
30A 65Vdc
I O
Volt:36Vdc = 20A
BATTERYCONNECTOR
U-Talk
5
12
710 811
9
6a 6b
Vac IN
6
4
13

MGE UPS SYSTEMS Pulsar EX
Rack : 86-153522-00 5
key to diagrams
2 "function" button: switches off audio
warning device or measures load
charge percentage (if utility power
present),
3 "ON/OFF" switch:
button pushed in: ON
button not pushed in: OFF,
4 input receptacle,
5 input cord (supplied, with ferrite for
Pulsar EX15 Rack )
6 input fuse receptacle,
6a input fuse:
T 15A/125V for Pulsar EX10 Rack ,
T 20A/125V for Pulsar EX15 Rack ,
6b fuse holder,
7 output receptacles for connection of
computer loads to Pulsar EX Rack ,
8 site wiring fault LED,
9 rating label,
yellow indicator LEDs 1a to 1d flashing
quickly:
1a overload,
1b device fault,
1c battery fault,
1d operating on bypass (fault tolerant
mode),
yellow indicator LEDs 1a to 1d on
continuously or flashing slowly: indicate
the battery charge level (if utility power
present) or remaining battery time (if no
utility power present). They may be on
continuously or flash slowly during a
transition period. By pressing the button
marked "function" 2when utility power is
present, they indicate the load charge level.
1e green indicator LED flashing: operating
on battery,
1f green indicator LED on continuously:
load powered by UPS,
green indicator light off: load no
powered by UPS,
10 fan,
11 SUB-D 9 pin connector for RS232
communication port,
12 cover for optional communication cards,
13 connector for Pulsar EXB10 Rack
EXB15 battery extension module,
14 warranty card,
17 Solution-PacTM ,CD-ROM, EX Drive,
18 RS232 cable,
19 Pulsar EXB10 Rack /EXB15 battery
extension module,
20 battery circuit-breaker,
21 connector to Pulsar EX10 Rack
EX15 Rack ,
22 connector for second Pulsar
EXB10 Rack /EXB15 battery extension
module,
23 battery connection cord.

6P-ulsar EX
Rack : 86-153522-00 MGE UPS SYSTEMS
technical data
coutput power:
vPulsar EX10 Rack : 1000VA/700W
vPulsar EX15 Rack : 1500VA/1050W
cinput voltage:
vPulsar EX10 Rack voltage (V): a 80V to 138V single phase (60V to 138V at 1/3 Power, 70V to 138V at 2/3 Power)
vPulsar EX15 Rack voltage (V): a 90V to 138V single phase (70V to 138V at 1/3 Power, 80V to 138V at 2/3 Power)
vfrequency (F): 47Hz to 53Hz or 57Hz to 63Hz
cbattery:
vtype :
maintenance free sealed lead-acid Pulsar EX10 Rack : 3 x 12V - 7.2Ah
Pulsar EX15 Rack : 4 x 12V - 7.2Ah
note: battery life (4 or 5 years) is halved every 10°C above 25°C
coutput specifications:
vvoltage (V): single phase 120V ±3% (can be adjusted from 100 to 127V using EX Driver)
vfrequency (F): 50/60Hz ±0.5% (frequency configuration using EX Driver)
cenvironment:
vnoise level: ≤40dBA (Pulsar EX10 Rack ) or ≤50dBA (Pulsar EX15 Rack ) for operation on utility power
≤45dBA (Pulsar /EX10 Rack ) or ≤50dBA (Pulsar EX15 Rack ) for battery backup mode
voperating temperature: 0 to 35°C
vrelative humidity: 0 to 90%
non condensing
cdimensions and weights: Pulsar EX10 Rack Pulsar EX15 Rack Pulsar EXB10 Rack
vheight H (inches): 3.46 3.46 3.46
vwidth W (inches): 19 19 19
vdepth D (inches): 16.25 19.5 16.25
vweight lbs (kg) : 37 (17) 51 (23) 48 (22)
–+
–+
/ a
/
a
H/2U
W
D

MGE UPS SYSTEMS Pulsar EX
Rack : 86-153522-00 7
Pulsar EX10 Rack battery back-up time Pulsar EX15 Rack battery back-up time
t (min)
0 50 100 150 200
ATM switch 32 slots
2 entry level servers
tower server + external mass storage / ATM switch 16 slots
tower server + modular hub
tower server
100 lines PBX
desktop server
entry level mini-computer system
t (h)
0123
EX10 Rack + 2 EXB10 Rack
EX10
Rack + EXB10 Rack
EX10 Rack
t (min)
0 80 160 240 320
EX15 Rack + 2 EXB15
EX15
Rack + EXB15
EX15 Rack
ATM switch 32 slots
2 entry level servers
tower server + external mass storage
tower server + modular hub
tower server
100 lines PBX
desktop server
entry level mini-computer system
t (h)
01234 5 6

8P-ulsar EX
Rack : 86-153522-00 MGE UPS SYSTEMS

MGE UPS SYSTEMS Pulsar EX Rack : 86-153522-00 9
contents
getting started ..................................................................................................................10
location......................................................................................................................................10
preliminary checks ....................................................................................................................10
connections ...............................................................................................................................10
communication .......................................................................................................................... 11
operation .............................................................................................................................12
starting up with utility power present .........................................................................................12
starting up with out utility power ................................................................................................13
operation on battery ..................................................................................................................14
overload ....................................................................................................................................15
operating anomalies..................................................................................................................15

10 Pulsar EX Rack : 86-153522-00 MGE UPS SYSTEMS
getting started
location
cobserve the safety rules indicated at the
beginning of this document.
preliminary checks
ccheck that button 3" " on the front is
not pushed in;
ccheck that rating shown on identification
plate 9corresponds to the input voltage
specification and power requirement of your
application.
connections
cuse your application cord to supply
input power to Pulsar as shown.
Connect the computer cord 5between
UPS utility power receptacle 4, and a
nearby utility power outlet. Note 1:
Following connection, the battery
automatically charges, whatever the position
of the ON/OFF button 3 "".
Note 2:
The batteries will provide full back-up time
after approximatively 8 hours of recharge
time.
Note 3:
The rating of input power cord must not be
less than the nominal input rating of
Pulsar EX10 Rack :Use the supplied cord.
cconnection of Pulsar EXB10 Rack
battery extension module (optional):
vcheck that button 3" " on the front of
the Pulsar EX10 Rack is not pushed in,
vdisconnect the utility power connection
cord 5 ,
vflip the circuit-breaker 20 of the unit to
the right (position "O"),
vconnect the battery connection cord 23
to connector 21 of the module and
connect 13 of the Pulsar EX10 Rack ,
vif the installation has 2 battery modules,
connect the second cord 23 to connectors
21 of the second module and 22 of the
first module,
vthe use of connectors 13 , 21 and 22
is strictly limited to connecting the battery
modules to the Pulsar EX10 Rack . Any other
connection to these connectors is prohibited
at the risk of damaging the battery and
losing the warranty,
vflip the battery circuit-breaker 20 to the
left (position "I"),
vif your installation is operated with MGE
UPS SYSTEMS software, update your
battery configuration with EX Tuner.
cuse IEC cords to connect your
applications to output sockets 7.
7
Vac IN
computer
loads
utility
power
outlet
Vac IN
5
4

MGE UPS SYSTEMS Pulsar EX Rack : 86-153522-00 11
communication
cthe U-Talk communication port, at the rear
of the Pulsar, delivers information in the
form of an RS232 series link supported by
the communication protocol exclusive to
MGE UPS SYSTEMS.
The Solution-PacTM programs use the data
made available by this protocol.
option 2
cSNMP card: after the card is installed in
the rear of the Pulsar, the communication
port transmits information supported by the
TCP/IP andSNMP protocols on an RJ45 or
BNC connector to any ethernet network.
Contact your sales agent for further details.
option 1
cstatus information card: after the card is
installed in the rear of the Pulsar,
communication port transmits the status
information on a SUB-D 9-pin female
connector using the following pinouts:
1- ground,
4- normal operation,
5- common,
6- operation on utility power,
7- low battery warning,
8- load supplied by UPS,
9- operation on battery.
optional port
12
54321
9876
0V
0V
n.o.
n.c.
0V
n.o.
0V
n.o.
0V
n.o.
Relay breaking capacity:
Vmax = 25V DC
Imax = 10mA
n.o. : normally open,
n.c. : normally closed.
With the EX Driver software program you
can set up Pulsar EX Rack to suit your user
conditions (EX Tuner). To install EX Driver,
connect the serial cable supplied to COM1
to COM4 (set up by EX Tuner) serial port of
your computer equipped with Windows 3.1
or 95/98 on the one end, and to the serial
Pulsar EX Rack connector on the other end.
Insert the CD and type A:\Install. Follow the
installation instructions on the screen.
11
54321
9876
0V RD TD
standard port

12 Pulsar EX Rack : 86-153522-00 MGE UPS SYSTEMS
operation
starting up with utility power present
17 s7 s5 s0 s
several beeps
UPS is on utility power
1 s beep
output off output off
normal operation
indicator lights testpress button "on/off" :
automatic sequence:
your load is supported
by the battery
device and battery test
indicating the
remaining battery
time percentage
(here 50%)
indicating the
recharge
percentage of the
battery (here 50%)
silence
silence

MGE UPS SYSTEMS Pulsar EX Rack : 86-153522-00 13
starting up with out utility power
17 s7 s5 s0 s
several beeps
1 s beep
output off output off
normal operation on battery
indicator lights testpress "on/off" button:
automatic sequence:
your load is supported
by the battery UPS is on utility power
device and battery test
indicating the
remaining battery
time percentage
(here 50%)
1 beep every 10 s
3 s beep
indicating the
remaining autonomy
percentage
(here 50%)

14 Pulsar EX Rack : 86-153522-00 MGE UPS SYSTEMS
operation on battery
no utility power
your load is supplied by the utility power
(on line)
At whatever point the utility power
returns, Pulsar switches to normal
operation:
return of utility power load charge percentage
Note:
The alarm silence button is to deactivate or
activate the audio warning device when
operating on battery, or when site wiring
fault occured.
If utility power is present, hold alarm
silence button in:
x + ε mn
x mn0 mn
Pulsar switches off
automatically
warning alarm at low
battery
indicating the
remaining battery
time: here, between
75 and 87%
silence
1 beep every 10 s
your load is supported
by the battery you have less than 12% battery time remaining: power down your load, Pulsar
will soon switch off automatically
UPS output "off"
1 beep every 3 s
break in utility power
indicating the battery
recharge percentage:
here, between 12 and
25%
silence
indicating the load
charge percentage:
here 50%
silence

MGE UPS SYSTEMS Pulsar EX Rack : 86-153522-00 15
overload
utility power present
automatic load transfer to bypass
operating anomalies
device fault
vv
vv
vautomatic load transfer to bypass,
vv
vv
vswitch off Pulsar (release "on/off" button),
disconnect from the wall socket (check input
cord), and check that Pulsar has not short-
circuited (disconnect all loads),
vv
vv
vif necessary, change the input fuse,
vv
vv
vre-start Pulsar.
battery fault
A battery test is carried out while Pulsar, is in
start-up mode, then automatically every 7
days (interval times adjustable using EX
Driver). If a battery fault is detected, the
following occurs:
recharge your battery for 8 hours.
operation on bypass
see "overload" and "device fault" section
Note:
This operating mode provides temporary
inverter fault tolerance.
no utility power present
Pulsar switches off automatically after a
length of time which depends on the level
of overload.
Note: overload occurs if the load
consumption is greater than the rated power
of Pulsar.
To acknowledge the fault, release the "on/
off" button, temporarily disconnected Pulsar
from the wall socket (check input cord),
disconnect loads and re-start Pulsar.
after the start-up sequence, if the audio
warning device sounds continuously,
recharge your battery for 8 hours.
Note: if the previous symptoms persist,
contact technical support.
battery low
1 beep
every
second
continuous
beep
…
1 beep
every
second
1 beep
every
second
1 beep
every
second
1 beep
every
second

16 Pulsar EX Rack : 86-153522-00 MGE UPS SYSTEMS