Mi-Light MiBOXER FUT086 User manual

This product is a 433MHz frequency wireless remote control. We use LoRa SPSP
Modem technology. It can control specified 433MHz series smart lights with color
changing, color temperature, saturation and brightness adjustable.
Products Key Diagram
Product Features
Model No.: FUT086
LoRa 433MHz RF Remote
Slide the brightness slider to adjust the brightness.
Touch the color ring to change colors.
Under white light mode, adjust color temperature;
Under color light mode, change color saturation.
M
S-
ON
OFF
WPress the button to get white light.
Touch ON button, turn on the linked device.
Touch OFF button, turn off the linked device.
Dynamic mode switching button.
Short press: Lower the dynamic mode speed.
Long press under static mode, lamp will blink one time into 60S Delay OFF mode.
Short press: Accelerate the dynamic mode speed.
Long press under static mode, lamp will blink one time into 10min Delay OFF mode.
S+
Color Ring
Antenna
Speed+ /
10min Delay OFF
Mode
Speed- / 60S Delay OFF
White light
Saturation / CCT Control
Indicator light
Master OFF
Master ON ON OFFW
MS- S+
1 2
3 4
5 6
7 8
“ ” Zone OFF
“ ” Zone ON
(Link/Unlink)
Brightness Dimming
LoRa 433MHz RF Remote
Technical Parameters
Model No.: FUT086
Voltage: 3V(AAA * 2PCS)
Transmitting Power: 10dBm
Standby Power Consumption: 16uA
RF: 433MHz
Modulation Method: LoRa Spread Spectrum
Control Distance: 50m(Lamps 0.5m underwater)Size: 197.5mm*47mm*19mm
19mm47mm
197.5mm
78mm
24mm
53mm
ON OFFW
MS- S+
1 2
3 4
5 6
7 8
LoRa 433MHz RF Remote
0298-2
Subordinate New Brand

Attention
1. In the using of the remote, if the indicated lamp blinking quickly, pls change the
battery in time. Pls don’t use poor quality battery to avoid the leaking of battery
liquid to damage the remote controller.
2. This 433MHz remote control system is precise electronic product; don’t use it in
humid, high temperature, dust and high voltage environment; Saving it at indoor, dry
and no static electricity environment.
3. Pls don’t use the remote controller on the wide-range metal or strong electromagnet-
ic wave area, otherwise, it will badly affect the controlling distance.
You can add an endless numbers of lights to a zone on the 8 channels remote by
linking the lights to different zones. This way you are completely flexible in creating
different group combinations. Below you can see some grouping examples.
Grouping of several lights
1 2 3 11 2
Remark:
1. The user can re-programme freely as needed. One remote can control countless
lamps or controllers, but one lamp or controller can only be controlled by four
remotes ( Max ).
2. Please check the battery installation and controller ( totally discharge the power ),
when you programme after switching off and switching on.
Linking Instructions
If the light not blink slowly, the linking failed, Pls switch off the light
again, and follow the above steps again.
Switch off the light,
after 10 seconds
switch on again
12
Power
3The light blink 3 times
slowly means the linking is
done successfully.
Power
When the light on, short press
any zone of " " 3 times within
3 seconds
Unlinking Instructions
If the light not blink quickly, the unlink failed, pls switch off the light
again, and follow the above steps to unlink again.
3The light blinking 10 times
quickly, means the unlinking
successfully.
Switch off the light,
after 10 seconds
switch on again
1When the light on, short press
" " 5 times within 3 seconds
2
Unlinking must be the same zone
with the Linking
Linking&Unlinking
Remark: The light can be working after linking with the remote controller.
Link/Unlinkbutton
Power Power
Light 1
Light 2
Light 3
Light 4
Light 5 Light 1
Light 2
Light 3
Light 4
Light 5 Light 1
Light 2
Light 3
Light 4
Light 5
ON OFFW
MS- S+
1 2
3 4
5 6
7 8
LoRa433MHz RF Remote
Link/UnlinkbuttonON OFFW
MS- S+
1 2
3 4
5 6
7 8
LoRa433MHz RF Remote
Made in China