Mi-Light FUT095 RGBW User manual

This manual describes two types of RGBW remote controls used for our RGBW product.
Both of them have same functions but different design. Each remote control can control
the led lights up to four different zones, change the color, dim/brighten the lights,
warm/cool white, different programs. In this manual.
Product Features
FUT095 RGBW remote control with buttons
FUT096 Touch screen RGBW remote control
Technical Parameters
Product Name: RGBW remote control with buttons
Model No.: FUT095
Voltage: 3V(AAA * 2PCS)
Transmission Frequency: 2.4GHz
Modulation Method: GFSK
Transmitting Power: 6dBm
Standby Power Consumption: 20uA
Control Distance: 30m
Size: 52.5*21*120mm
21mm
21mm
Product Name: Touch screen RGBW remote control
Model No.: FUT096
Voltage: 3V(AAA * 2PCS)
Transmission Frequency: 2.4GHz
Modulation Method: GFSK
Transmitting Power: 6dBm
Standby Power Consumption: 20uA
Control Distance: 30m
Size: 52.5*21*120mm
52.5mm
120mm
52.5mm
120mm
ON OFF
OFF
M
M
S-
S- S+ S+
1 2 3 4
FUT095
ON OFF
OFF
M
M
S-
S- S+ S+
1 2 3 4
Color ring
Brightness- Brightness+
Master OFF
Master ON
Zone ON
Zone OFF
Modes(Programs)
Speed- Speed+
4×(un) Link Light
Indicator light
FUT096
Color ring
Brightness- Brightness+
Zone ON
Zone OFF
Modes(Programs)
Speed- Speed+
4×(un) Link Light
Indicator light
Master ON Master OFF
Products Key Diagram
Remark: Hold " " to get white mode. Under white mode, press ‘S-’ to get warm white,
press ‘S+’ to get cool white. Under color mode, press ‘S+/S-’ for saturation control. When
press 'M', S+/S- can adjust the speed of the dynamic modes.
To dim all RGBW lights at once or change the color, frist press “Master ON”. to do this
with individual lights, frist press “Zone ON”. secondly, choose the color or brightness
according to the color ring or brightness ring.

Made in China
Attention
1. This remote controller only control specified Mi-Light products; not all Mi-Light series
can work on this remote controller.
2. In the using of the remote, if the indicated lamp blinking quickly, pls change the
battery in time. Pls don’t use poor quality battery to avoid the leaking of battery
liquid to damage the remote controller.
3. Please keep your finger off the touch ring when installing the batteries, to improve
its sensitivity, and use the remote ( 3 seconds later ) after the batteries are installed.
Please reinstall the batteries, if the fouch ring is found low-sensitivity.
4. This 2.4GHz remote control system is precise electronic product; don’t use it in
humid, high temperature, dust and high voltage environment; Saving it at indoor, dry
and no static electricity environment.
5.
Pls don’t use the remote controller on the wide-range metal or strong electromagnetic
wave area, otherwise, it will badly affect the controlling distance.
Linking Instructions
If the light not blink slowly, the linking failed, Pls switch off the light
again, and follow the above steps again.
Switch off the light,
after 10 seconds
switch on again
1 2
Power
3The light blink 3 times slowly
means the linking is done
successfully.
Power
When the light on, short press
any zone of " " 1 time within 3
seconds
Unlinking Instructions
If the light not blink quickly, the unlink failed, pls switch off the light
again, and follow the above steps to unlink again.
Power
3The light blinking 10 times
quickly, means the unlinking
successfully.
Power
Switch off the light,
after 10 seconds
switch on again
1When the light on, long press
" " within 3 seconds
2
Unlinking must be the same
zone with the Linking
Linking&Unlinking
Remark: The light can be working after linking with the remote controller.
You can add an endless numbers of lights to a zone on the 4 channel remote by
linking the lights to different zones. This way you are completely flexible in creating
different group combinations. Below you can see some grouping examples.
Grouping of several lights
Remark:
1. The user can re-programme freely as needed. One remote can control countless
lamps or controllers, but one lamp or controller can only be controlled by four
remotes ( Max ).
2. Please check the battery installation and controller ( totally discharge the power ),
when you programme after switching off and switching on.
Link/Unlink
button
Link/Unlink
button
0157-2