ZIGBEE SR-ZG9001K2-DIM User manual

Single Color Wall Mounted ZigBee Remote Controller
09.ZGK4D.04836
55.57 mm
71.20 mm
11 mm
Function introduction
Important: Read All Instructions Prior to Installation
Front side
Back side
Battery: CR2430
Before the first use, please remove the protective film
• Single color ZigBee remote controller.
• Supports 1 group for binding lighting devices.
• 2.4 GHz global operation.
• Long battery life mesh technology.
• Transmission range up to 30m.
• Compatible with ZigBee Gateway products.
• Compatible with single color ZigBee lighting
devices.
Product Data
55.57 mm
71.20 mm
The remote control can be fixed on
the wall with 3M glue or screw.
• This device contains a button lithium battery that shall be stored and disposed properly.
• DO NOT expose the device to moisture.
Safety & Warnings
71.2x71.2x13.6mm
Operation
1. This wall controller is a single color ZigBee remote control that works with a ZigBee
gateway/coordinator, it shall join ZigBee network and bind compatible ZigBee lighting devices from
ZigBee controller or hub interface so that it can control the devices.
2. This ZigBee remote supports 1 group for binding lighting devices and enables to control single color
ZigBee lighting devices.
3. ZigBee Network Pairing – Join the remote to the ZigBee network
1) The ZigBee remote is under sleepy mode at most of the time due to ZigBee low power mesh network. Before
pairing to ZigBee network, press and hold down both I and O keys until the LED status indicator turns on green
and flashes 3 times quickly, then flashes every 2 seconds to indicate the remote is activated and searching
nearby network. Once timeout, the indicator will turn off, repeat the operation.
2) From your ZigBee Controller or hub interface, choose to add device and enter Locating/Pairing mode as
instructed by the controller.
3) Network Pairing Begins Automatically: LED indicator on the remote blinks 5 times quickly as the remote
scans for a compatible network controller to pair with.
4) After the remote is located and paired to the ZigBee network, the indicator will stop blinking and turn off, then
the remote will appear in your controller's menu.
5) The remote is now paired to the ZigBee network.
4.The remote has battery power monitor function:
1) Press and hold down both I and O keys at the top row to report battery power value to the gateway.
2) The remote will wake up every 2 hours to check battery power, and will report battery power value to the
gateway if the voltage is≤ 2.7V.
5. Binding Between the Remote and ZigBee Lighting Devices
1)Once the remote and compatible ZigBee lighting devices are paired to the same network, from your ZigBee
controller or hub interface, choose to bind devices to the remote as instructed by the controller. Then the
devices can be controlled by the remote.
2)Once the binding operation is done between the remote and ZigBee lighting devices, the remote can still
control the devices in the event of gateway/coordinator loss.
Press and hold down both keys together to search and
pair to ZigBee network or factory reset the controller.
Click to turn on.
Press and hold down to
increase light intensity.
Note: This remote
supports 1 group for
binding lighting devices.
Transmission Range
(free field) 30m
Operating temperature 0-40°C
Relative humidity 8% to 80%
Dimming Range 0.1%-100%
Power Supply 3VDC (Cr2430)
Operation Frequency 2.4GHz
Dimensions
Protection Type Ip20
Click to turn off.
Press and hold down to
decrease light intensity.

Mounting
The key part of this controller is an universal one, especially rotary standard switch element that can be
integrated in numerous frames by different manufactures as below list:
BEKER S1, B1, B3, B7 glass
GIRA Standard55, E2, Event, Esprit
JUNG A500, Aplus
MERTEN M-smart, M-Arc, M-Plan
Note: This remote supports 1 group for binding lighting devices. Each group supports maximum 12
devices.
6. Unbinding Between the Remote and ZigBee Lighting Devices
To unbind the remote and ZigBee lighting devices, from your ZigBee controller or hub interface, choose to
unbind the device from a remote as instructed by the controller.
7. Factory Reset the Remote (Remove From ZigBee Network)
From the ZigBee Controller or Hub Interface
1)From your ZigBee controller or hub interface, choose to remove or reset the remote as instructed. The LED
indicator on the remote will turn on green and flash 3 times quickly and then flash every 2 seconds to indicate
successful reset and searching for a network again.
Manual
2)Press and hold down both I and O keys on the remote until the LED indicator on the remote turns on green
and flashes 3 times quickly and then flash every 2 seconds to indicate successful reset and searching for a
network again.
Note: All configuration parameters will be reset after the remote is removed from the network.