Mi-T-M CD Series User manual

Mi-T-MCD-GASOLINE Operator's Manual 1
©Copyright 2005, Mi-T-M Corporation Form #37-0353-E-S-091305
OPERATOR'S MANUAL FOR
CD-GASOLINE
COLD WATER DIRECT DRIVEN
PRESSURE WASHERS
CAUTION
RISK OF INJURY!
READ MANUAL BEFORE OPERATING!
THIS MANUAL IS AN IMPORTANT PART OF THE PRESSURE WASHER
AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT.

2 Mi-T-M®CD-GASOLINE Operator's Manual
TABLE OF CONTENTS
INTRODUCTION.............................................................................................................................3
IMPORTANT SAFETY WARNINGS.............................................................................................4-7
FIRE & VENTILATION PRECAUTIONS.............................................................................4
SPRAY PRECAUTIONS.....................................................................................................5
DETERGENT CLEANING PRECAUTIONS ....................................................................... 6
MISCELLANEOUS SAFETY PRECAUTIONS ................................................................... 6
ADJUSTMENT PRECAUTIONS ........................................................................................7
FEATURES DRAWINGS........................................................................................................ 8 & 10
CD-HAND-CARRY SERIES ...............................................................................................8
CD-CART SERIES ...........................................................................................................10
SAFETY DECALS...................................................................................................................9 & 11
CD-HAND-CARRY SERIES ...............................................................................................9
CD-CART SERIES ........................................................................................................... 11
INSTALLATION & PREPARATION .........................................................................................12-15
ATTIRE .............................................................................................................................12
SET-UP.............................................................................................................................12
ENGINE FUEL TANK .......................................................................................................12
NOZZLE REVIEW ............................................................................................................13
NOZZLE CONNECTION ..................................................................................................13
WATER SUPPLY ..............................................................................................................14
UNLOADER......................................................................................................................14
THERMAL RELIEF VALVE...............................................................................................14
PRE-START INSPECTION PROCEDURES ....................................................................15
OPERATING INSTRUCTIONS ................................................................................................16-17
PRIMING THE PUMP.......................................................................................................16
START-UP ........................................................................................................................16
CLEANING WITH DETERGENTS ...................................................................................17
SHUTDOWN ....................................................................................................................17
STORAGE & MAINTENANCE.................................................................................................18-19
SPECIFIC MAINTENANCE .............................................................................................18
WINTERIZING..................................................................................................................19
TROUBLESHOOTING..................................................................................................................20
ACCESSORIES ............................................................................................................................21
STATEMENT OF WARRANTY .....................................................................................................22
NOTES ..........................................................................................................................................23

Mi-T-MCD-GASOLINE Operator's Manual 3
INTRODUCTION
Congratulations on the purchase of your new Mi-T-M pressure washer! You can be assured your Mi-T-M pressure
washer was constructed with the highest level of precision and accuracy. Each component has been rigorously tested
by technicians to ensure the quality, endurance and performance of this unit.
This operator's manual was compiled for your benet. By reading and following the simple safety, installation, operation,
maintenance and troubleshooting steps described in this manual, you will receive years of trouble free operation from
your new Mi-T-M pressure washer. The contents of this manual are based on the latest product information available at
the time of publication. Mi-T-M reserves the right to make changes in price, color, materials, equipment, specications
or models at any time without notice.
! IMPORTANT !
Theseparagraphsaresurroundedbya"SAFETYALERTBOX". Thisboxisusedtodesignateand
emphasize Safety Warnings that must be followed when operating this pressure washer.
Accompanying the Safety Warnings are "signal words" which designate the degree or level
of hazard seriousness. The "signal words" used in this manual are as follows:
DANGER: Indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided MAY
result in minor or moderate injury.
The symbols set to the left of this paragraph are "Safety Alert Symbols". These symbols
are used to call attention to items or procedures that could be dangerous to you or other
persons using this equipment.
ALWAYS PROVIDE A COPY OF THIS MANUAL TO ANYONE USING THIS EQUIPMENT. READ
ALL INSTRUCTIONS BEFORE OPERATING THIS PRESSURE WASHER AND ESPECIALLY
POINT OUT THE "SAFETY WARNINGS" TO PREVENT THE POSSIBILITY OF PERSONAL
INJURY TO THE OPERATOR.
Once the unit has been uncrated, immediately write in the serial number of your unit in the space provided below.
SERIAL NUMBER_________________________________
Inspect for signs of obvious or concealed freight damage. If damage does exist, le a claim with the transportation
company immediately. Be sure that all damaged parts are replaced and that the mechanical problems are corrected
prior to operation of the unit. If you require service, contact Mi-T-M Customer Service at 800-553-9053.
Please have the following information available for all service calls:
1. Model Number
2. Serial Number
3. Date and Place of Purchase
Mi-T-M Corporation
8650 Enterprise Drive
Peosta, IA 52068-0050

4 Mi-T-M®CD-GASOLINE Operator's Manual
IMPORTANT SAFETY WARNINGS
FIRE & VENTILATION PRECAUTIONS:
1. This unit was designed for outdoor use only. NEVER operate this unit in
an enclosed area. ALWAYS make certain there is adequate air (oxygen)
for combustion as well as ventilation to prevent the presence of poisonous
carbon monoxide gases. Beware of poorly ventilated areas or exhaust fans
which can cause inadequate combustion or engine overheating.
2. NEVER operate this unit in the presence of ammable vapors or combustible
dust, gases or other combustible materials. (Aspark may cause an explosion
or re.) When servicing this machine, be especially careful to properly
dispose of any ammable materials. DO NOT spray ammable liquids.
3. ENGINE FUEL TANK:
a. DO NOT SMOKE WHILE FILLING ENGINE FUEL TANK
b. NEVER ll the engine fuel tank while the unit is running or hot. Allow
the engine to cool two minutes before refueling.
c. DO NOT refuel indoors or in a poorly ventilated area.
d. ALWAYS refuel slowly to avoid the possibility of spilled fuel which may
cause a risk of re.
4. DO NOT operate the unit if gasoline is spilled. Wipe unit clean and move
the unit away from the spill. Avoid creating any ignition until the gasoline
has evaporated.
5. DO NOT store the unit near an open ame or any equipment such as a
stove, furnace, water heater, etc., which utilizes a pilot light or devices which
can create a spark.
IMPORTANT
The following is required by California State law, Section 4442 of the California
Public Resources Code. Other states may have similar laws. Federal laws
apply on federal lands.
A spark arrester must be added to the mufer of this engine if it is
to be used on any forest covered, brush covered or grass covered
unimproved land. The arrester must be maintained in effective
working order by the operator.
See your engine or equipment dealer for spark arrester mufer options.

Mi-T-MCD-GASOLINE Operator's Manual 5
IMPORTANT SAFETY WARNINGS
SPRAY PRECAUTIONS:
DANGER
RISK OF INJECTION OR SEVERE CUTTING INJURY
KEEP CLEAR OF NOZZLE
DO NOT DIRECT DISCHARGE STREAM AT PERSONS OR PETS
ONLY TRAINED OPERATORS SHOULD USE THIS PRODUCT. WHEN
USING THIS PRODUCT, BASIC PRECAUTIONS SHOULD ALWAYS BE
OBSERVED INCLUDING THE FOLLOWING:
1. KEEP AWAY FROM THE SPRAY:
a. Because of the high pressure and velocity of the spray, uids can
penetrate the skin, causing serious injury.
b. Never point the gun at yourself of anyone else. Never put your hand,
ngers or body directly over the spray nozzle. Always keep operating
area clear of all persons. Use extreme caution when operating near
children.
c. If an accident does occur and the spray appears to have penetrated
the skin, SEEK EMERGENCY MEDICAL CARE. DO NOT TREAT
AS A SIMPLE CUT. If you are using cleaning agents, be prepared
to tell a physician exactly what kind.
2. ALWAYS wear protective goggles when operating the unit to shield the
eyes from ying debris and detergents. Other protective equipment such
as rubber suits, gloves and respirators are advisable, especially when
using cleaning detergents. Use extreme caution when operating near
children.
3. Stay alert-watch what you are doing. Do not operate the unit when
fatigued or under the inuence of alcohol or drugs.
4. NEVER squeeze the trigger unless securely braced. The thrust from
the water traveling through the nozzle may be powerful enough to cause
the operator to lose balance if unprepared. DO NOT overreach or stand
on unstable support. Wet surfaces can be slippery, wear protective foot
gear and keep good footing and balance at all times. NEVER trigger
the gun while on a ladder or roof.
5. Caution should be used when directing spray toward fragile materials
such as glass. Shattering could result in serious injury.
6. ALWAYS hold on rmly to the gun/wand assembly when starting and
operating the unit. Failure to do so can cause the wand to fall and whip
dangerously. NEVER operate the gun with the trigger wired in the open
position. To prevent accidental discharge, the trigger gun should be
securely locked when not in use.
7. DO NOT direct spray on or into electrical installations of any kind! This
includes electrical outlets, light bulbs, fuse boxes, transformers, the unit
itself, etc. Severe electrical shock may occur.
8. Even after you shut off the unit, there is high pressure water left in the
pump, hose and gun until you release it by triggering the gun. Before
removing the spray nozzle or servicing the unit, ALWAYS shut off the
unit and trigger the gun to release trapped pressure.

6 Mi-T-M®CD-GASOLINE Operator's Manual
IMPORTANT SAFETY WARNINGS
DETERGENT CLEANING PRECAUTIONS:
1. DO NOT use solvents or highly corrosive detergents or acid type cleaners
with this pressure washer. Use only Mi-T-M detergents.
2. KNOW YOUR DETERGENTS! Be prepared to tell a physician exactly what
you are using in the event of an emergency. Read the Material Safety Data
Sheet (MSDS) provided with your Mi-T-M Detergent and all detergent labels.
Follow all appropriate instructions regarding preparation use, safety and
transportation. Keep ALL detergents out of the reach of children.
3. DO NOT use this pressure washer to dispense hazardous detergents.
4. DO NOT alter the detergent injection feature in any manner not prescribed
in this manual. Use only genuine Mi-T-M replacement parts for necessary
repairs.
MISCELLANEOUS SAFETY PRECAUTIONS:
1. NEVER ALLOW CHILDREN OR ADOLESCENTS TO OPERATE THIS
UNIT!
2. Readandfollowallhandling,operations,maintenanceandsafetyinstructions
listed in this manual and the Engine Operator's manual that accompanies
this unit, and provide such information to ANYONE who will be operating
this unit.
3. In freezing temperatures, the unit must always be warm enough to ensure
there is no ice formation in the pump. DO NOT start this unit if it has been
transported in an open or underheated vehicle without rst allowing the
pump to thaw.
4. When connecting the water inlet to the water supply mains, local regulations
of your water company must be observed. In some areas the unit must not
be connected directly to the public drinking water supply. This is to ensure
that there is no feedback of the detergents into the water supply. (Direct
connection is permitted if a back ow preventer is installed.)
5. DO NOT allow any part of your body or the high pressure hose to make
contact with the mufer. Avoid dragging the hose over an abrasive surface
such as cement. This causes wear and eventual rupturing.
6. High pressure hoses should be inspected daily for signs of wear. If evidence
of failure exists, promptly replace all suspect hoses to prevent the possibility
of injury from the high pressure spray. If a hose or tting is leaking , NEVER
place your hand directly on the leak.
7. DO NOT operate the unit if you see any pump oil or water leaks from the
machine. DO NOT resume operation until the unit has been inspected and
repaired by a qualied service person.
8. DO NOT operate the unit without all protective covers in place.
9. NEVER run the unit with the governor disconnected or operate at excessive
speeds.
10. To reduce the risk of injury, maintain a safe distance for persons while
operating this unit. Close supervision is necessary when operating the unit
near children.
11. DO NOT leave pressurized unit unattended. Shut off the unit and release
trapped pressure before leaving.
12. DO NOT move the unit by pulling on the hose.

Mi-T-MCD-GASOLINE Operator's Manual 7
IMPORTANT SAFETY WARNINGS
ADJUSTMENT PRECAUTIONS:
1. NEVER alter or modify the equipment, be sure any accessory items and
system components being used will withstand the pressure developed.
Use ONLY genuine Mi-T-M parts for repair of your pressure washer.
Failure to do so can cause hazardous operating conditions and will void
warranty.
2. NEVER make adjustments to the machinery while it is connected to the
engine without rst removing the ignition cable from spark plug. Turning
the machinery over by hand during adjustment or cleaning might start the
engine and machinery with it, causing serious injury to the operator.
3. Know how to stop the pressure washer and bleed pressures quickly. Be
thoroughly familiar with controls.
4. Before servicing the unit; turn the unit off, relieve the water pressure,
and allow the unit to cool down. Service in a clean, dry, at area. Block
the wheels to prevent the unit from moving.
5. Follow the maintenance instructions specied in this manual.
! SAVE THESE INSTRUCTIONS !

8 Mi-T-M®CD-GASOLINE Operator's Manual
CD-HAND-CARRY SERIES
10. Decal: Caution-Engine Fuel
11. Pump
12. Oil Dipstick
13. Oil Sight Glass
14. Water Outlet
15. High Pressure Discharge Hose
16. Gun/Wand Assembly
17. Decal: Warning-Risk of Injection
18. Quick Connect Nozzle
1. Detergent Strainer
2. Detergent Hose
3. Water Inlet Strainer
4. Water Inlet
5. Adjustable Unloader Knob
6. Thermal relief Valve
7A. Decal: Warning Statements
7B. Decal: Caution Statements
8. Engine
9A. Decal: Warning-Mufer Hot
9B. Decal: Warning-Hand Carry
FEATURES LISTING
CDGAS HANDCARRY-011400-RD
THISSIDEONL
Y
.
CARRYUNITFROM
200
EXCEED150F
.
AREASMAY
! WARNING
SURROUNDING
MUFFLERAND
HOTSURFACES

Mi-T-MCD-GASOLINE Operator's Manual 9
SAFETY DECALS & PLACEMENT FOR CD-HAND-CARRY SERIES
REFER TO PAGE 8 FOR PLACEMENT
Reference #10 Decal: Caution-Engine Fuel (Part #34-0599)
Reference #17 Decal: Warning-Risk of Injection (Part #34-1253)
Reference #9A Decal: Warning-Mufer Hot (Part #34-0598) Reference 9B Decal: Warning-Hand
Carry
(Part # 34-0662)
Reference #7A Decal: Warning Statements (Part #34-0582)
Reference #7B: Decal: Caution Statements (Part #34-0583)
34-0599-E/S-030600-ENG
No ponga combustible cuando
el producto este en operacion.
Permita que el motor se enfrie
por 2 minutos antes de
reablastecer de combustible.
RISK OF FIRE
Do not add fuel when
product is operating. Allow
engine to cool for two (2)
minutes before refueling.
RIESGO DE FUEGE
CAUTION/PRECAUCION
RISK OF INJECTION OR SEVERE INJURY.
Never put your hand, fingers or body directly
over the spray nozzle.
34-1253-030801-ENG.
WARNING ADVERTENCIA
RIESGO DE INYECCION O LISION SEVERA
Nunca coloque la mano, los dedos o el cuerpo
directamente sobre la boquilla de rocío.
RISK OF BURNS
MUFFLER AND
ADJACENT AREAS
MAY EXCEED 150°F.
RIESGO DE QUEMAR
EL AMORTIGUADOR Y LAS
AREAS ADYACENTES PUEDEN
TENER TEMPERATURAS POR
ARRIBA DE 150°F.
34-0598-010699-E/S-ENG.
WARNING ADVERTENCIA
WARNING
HOT SURFACES.
MUFFLER AND
SURROUNDING
AREAS MAY 
EXCEED 150˚F.
CARRY UNIT FROM
THIS SIDE ONLY.
34-0662-042400-ENG.
WARNING
•RISK OF INJECTION OR SEVERE INJURY: KEEP CLEAR OF 
NOZZLE. DO NOT DIRECT SPRAYTOWARD ANY PERSON OR 
SELF.
•RISK OF ASPHYXIATION: OUTDOOR USE ONLY REQUIRED.
•RISK OF FIRE: DO NOT SMOKEWHILE REFUELING. ALLOW 
TO COOLTWOTOTHREE MINUTES BEFORE REFUELING.
•RISK OF ELECTROCUTION: DO NOT DIRECT SPRAYTOWARD
ANY ELECTRICAL CONNECTIONS, OUTLETS OR POWER 
LINES.
•RISK OF EXPLOSION: DO NOT SPRAY FLAMMABLE LIQUIDS.
•RISK OF INJURY: USE ONLY PROPERLY RATED EQUIPMENT.
34-0582-022599-ENG.D1
CAUTION
•To Reduce Risk of Injury:Read and understand the
operation manual and all instructions before using.
•Stay Alert:Hold on to gun/wand firmly with both hands
to avoid dangerous kickbacks.Always wear eye
protection.
•Do not overreach or stand on unstable support.Keep
good footing and balance at all times.
•Always turn on water supply to pump before starting.
•Protect pump from freezing.
•Engage trigger safety lock-off when not in use.
34-0583-030600-ENG.

10 Mi-T-M®CD-GASOLINE Operator's Manual
CD-CART SERIES
10. Decal: Caution-Engine Fuel
11. Pump
12. Oil Dipstick
13. Oil Sight Glass
14. Water Outlet
15. High Pressure Discharge Hose
16. Gun Assembly
17. Decal: Warning-Risk of Injection
18. Lance
1. Detergent Strainer
2. Detergent Hose
3. Water Inlet Strainer
4. Water Inlet
5. Adjustable Unloader Knob
6. Thermal relief Valve
7. Decal: Caution/Warning Statements
8. Engine
9. Decal: Warning-Mufer Hot
FEATURES LISTING
CDGAS CART2-011400-EDW

Mi-T-MCD-GASOLINE Operator's Manual 11
Reference #10 Decal: Caution-Engine Fuel (Part #34-0599) E/S
Reference #17 Decal: Warning-Risk of Injection (Part #34-1253)
Reference #9 Decal: Warning-Mufer Hot (Part #34-0598) E/S
Reference #7 Decal: Caution/Warning Statements (Part #34-0981) E/S
SAFETY DECALS & PLACEMENT
FOR CD-CART SERIES
REFER TO PAGE 10 FOR PLACEMENT
34-0599-E/S-030600-ENG
No ponga combustible cuando
el producto este en operacion.
Permita que el motor se enfrie
por 2 minutos antes de
reablastecer de combustible.
RISK OF FIRE
Do not add fuel when
product is operating. Allow
engine to cool for two (2)
minutes before refueling.
RIESGO DE FUEGE
CAUTION/PRECAUCION
RISK OF INJECTION OR SEVERE INJURY.
Never put your hand, fingers or body directly
over the spray nozzle.
34-1253-030801-ENG.
WARNING ADVERTENCIA
RIESGO DE INYECCION O LISION SEVERA
Nunca coloque la mano, los dedos o el cuerpo
directamente sobre la boquilla de rocío.
RISK OF BURNS
MUFFLER AND
ADJACENT AREAS
MAY EXCEED 150°F.
RIESGO DE QUEMAR
EL AMORTIGUADOR Y LAS
AREAS ADYACENTES PUEDEN
TENER TEMPERATURAS POR
ARRIBA DE 150°F.
34-0598-010699-E/S-ENG.
WARNING ADVERTENCIA
• RISK OF INJECTION OR SEVERE INJURY. KEEP CLEAR OF
NOZZLE DO NOT DIRECT SPRAY TOWARD ANY PERSON OR
SELF.
• RISK OF ASPHYXIATION. OUTDOOR USE ONLY REQUIRED.
• RISK OF FIRE. DO NOT SMOKE WHILE REFUELING. ALLOWTO
COOL TWO TO THREE MINUTES BEFORE REFUELING. DO NOT
OPERATE WHILE REFUELING.
• RISK OF ELECTROCUTION. DO NOT DIRECT SPRAY TOWARD
ANY ELECTRICAL CONNECTIONS, OUTLETS, OR POWER LINES. 
• RISK OF EXPLOSION. DO NOT SPRAY FLAMMABLE LIQUIDS. 
• TO REDUCE RISK OF INJURY: READ AND UNDERSTAND THE
OPERATION MANUAL AND ALL INSTRUCTIONS BEFORE
USING.
• STAY ALERT: HOLD ONTO GUN/WAND FIRMLY WITH BOTH
HANDS TO AVOID DANGEROUS KICKBACKS.
• ALWAYS WEAR EYE PROTECTION.
• DO NOT OVERREACH OR STAND ON UNSTABLE SUPPORT.
KEEP GOOD FOOTING AND BALANCE AT ALL TIMES.
• ALWAYS TURN ON WATER SUPPLY TO PUMP BEFORE
STARTING.
• PROTECT PUMP FROM FREEZING.
• ENGAGE TRIGGER SAFETY LOCK-OFF WHEN NOT IN USE.

• AFTER ENSURING ALL CONNECTIONS ARE SECURE, OPEN INLET
WATER SUPPLY COMPLETELY. DO NOT OPERATEWITHOUT WATER.DO
NOT USE WATERTHAT IS OVER 125˚F. • WITH GUN LOCKED, REMOVE
NOZZLE.POINT GUN IN A SAFE DIRECTION. BRACEWAND SECURELY
TO AVOID RECOIL.SQUEEZETRIGGER OPEN. STEADY THE UNIT AND
START BY PULLING ON THE STARTER ROPE. • AFTER ENGINE IS
RUNNING, LOCK GUN AND INSERT DESIRED NOZZLE. POINT GUN IN A
SAFE DIRECTION.UNLOCK GUN AND SQUEEZETRIGGER TO SPRAY
AND RELEASETHETRIGGER TO STOP SPRAY. • AFTER STOPPING THE
ENGINE, ALWAYSTURN OFFWATER SUPPLY AND SQUEEZETRIGGER
TO
RELEASE TRAPPED PRESSURE.
• RIESGO DE INYECCION O LESION SEVERA. MANTENGA LA
BOUILLA DESPEJADA. NO DIRIJA EL CHORRO HACIA PERSONA
ALUNA O HACIA USTED.
• RIESGO DE ASFIXIA: UNICAMENTE PARA USO EN EL EXTERIOR.
• RIESGO DE FUEGO: NO FUME MIENTRAS ESTE
REABASTECIMIENTO DE COMBUSTIBLE. PERMITA QUE EL
MOTOR SE ENFRIE DOS O TRES MINUTOS ANTES DEL
REABASTECIMIENTO. NO OPERE EL PRODUCTOR DURANTE EL
REABASTECIMIENTO. 
• RIESGO DE ELECTROCUCION: NO DIRECTA EL CHORRO HACIA
CONEXIONES. ELECTRICAS. TOMAS DE CORRIENTE O LINEAS
DE ALIMENTACION DE CORRIENTE.
• RIESGO DE EXPLOSION: NO ROCIE LIQUIDOS INFLAMMABLES.
• RIESGO DE LESION: USE UNICAMENTE EQUIP CON
CLASIFICACION ADEDUADA.

• PARA REDUCIR EL RIESGO DE QUE OCURRAN LESIONS:
LEA Y ENTIENDA EL MANUAL DE OPERACIONY TODAS LAS 
INSTRUCCIONES ANTE DE USAR EL PRODUCTO.
• PERMANIZCA ALERTA: SOSTENGA LA PISTOLA VARILLA 
FIRMENMENTE CON AMBAS MANO PARA EVITAR GOLPES
DE RETROCESO PELIGROSOS.
• USE SIEMPRE PROTECCION OCULAR.
• NO SE EXTIENDA DEMASIADO O SE PARE EN UN APOYO 
INESTABLE. MANTENGA UNA BUENA POSICIONY
BALANCE TODO EL TIEMPO.
• ANTES DE COMENZAR. ABRA SIENPRE EL SUMINSTRO DE 
AGUA A LA BOMBA.
• PROTEJA LA OMBA DE LA CONGELACION. 
• COLOQUE EL SUGURO DEL GATILLO EN LA POSICION 
APAGADO CUANDO NO ESTE USANDO EL PRODUCTO.
• DISPUES DE ASEGURARSE QUETODAS LAS CONEXIONES 
ESTAN SEGUIRSE. ABRA LA ENTRADA DEL SUMINSTRO DE AGUA 
COMPLETAMENT NO SE OPERE SIN AGUA. NO SE USE CON AGUA 
CONTEMPERATURAS DE MAS DE 125˚F.
• CON LA PISTOLA ASEGURADA.REMUEVA LA BOQUILLA 
APUNTANDO LA PISTOLA HACIA UNA DIRECCION SEGURA.
REFURESE LAVARA PARA EVITAR QUE RETROCEDA.APRIETE EL 
GATILLO PARA ABRIRLO. MANTEGA LA UNIDAD QUIETA.Y COMIENZE 
HALANDO FIRMEMENTE EN LA CUERDA DE INICIAR.
• DESPUES DE QUE EL MOTOR ESTE TRABAJANDO. ADJUSTE LA 
BOQUILLA A LA POSICION DESEADA.APRIETE EL GATILLO PARA 
ROCIARY SUELTELO PARA DETENER EL ROCIADO. 
• DESPUES DE DETENER EL MOTOR. CIERRE DIEMPRE EL 
SUMINSTRO DEL AGUO AND APRIETE EL GATILLO PARA LIBERAR
LA PRESION ATRAPADA.
WARNING/ADVERTENCIA CAUTION/PRECAUCION OPERATION/OPERACION
34-0981-063099-E/S-ENG.

12 Mi-T-M®CD-GASOLINE Operator's Manual
INSTALLATION & PREPARATION
SETUP:
1. This unit should only be placed on a level surface to ensure proper lubrication
for the engine and water pump while operating. NEVER spray water directly
on the unit!
2. Do not place unit in an area:
a. with insufcient ventilation
b. where there is evidence of oil or gas leaks
c. where ammable gas vapors may be present
3. Be certain to block the wheels to prevent the unit from moving while
operating.
4. Do not allow the unit to be exposed to rain, snow or freezing temperatures.
If any part of the unit becomes frozen, excessive pressure may build up in
the unit which could cause it to burst resulting in possible serious injury to
the operator or bystanders.
5. Before initial use, ensure the oil dipstick is inserted into the pump. Because
of varying shipping requirements, the pump may need to be shipped with
an oil travel plug instead of the dipstick in the pump. If your pump has been
shipped with an oil travel plug, you will need to remove it and replace the
plug with the oil dipstick provided with the unit.
6. Once properly installed, check the oil sight glass on the pump crankcase.
Make certain the oil level is in the center of the sight glass before each use.
If the level appears to be low, use Mi-T-M pump oil #AW-4085-0016. DO
NOT OVERFILL!
ATTIRE:
Proper attire is essential to your safety. It is advised to utilize whatever means
necessary to protect eyes, ears, and skin. Additional safety attire (such as
respiratory mask) may be required when using detergent cleaning agents with
this washer.
WARNING
RISK OF EXPLOSION OR FIRE!
ALWAYS STORE FUEL AWAY
FROM THE WASHER WHILE THE
UNIT IS RUNNING OR HOT.
DANGER
RISK OF FIRE!
-DO NOT SM O K E W H ILE
FUELING!
-DO NOT FILL THE FUEL TANK
WHILE UNIT IS RUNNING OR
HOT. ALLOW UNIT & ENGINE
TO COOL FOR TWO MINUTES
BEFORE REFUELING.
-DO NOT FILL FUEL TANK TO
POINT OF OVERFLOWING.
ALLOW APPROXIMATELY 1/4"
OF TANK SPACE FOR FUEL
EXPANSION.
DANGER
RISK OF EXPLOSION OR FIRE!
DO NOT PLACE UNIT IN AN
AREA WHERE FLAMMABLE
GASVAPORSMAYBEPRESENT.
A SPARK COULD CAUSE AN
EXPLOSION OR FIRE!
RISK OF UNIT BURSTING!
DONOTSTORE/OPERATEUNITIN
A FREEZING ENVIRONMENT!
WARNING
RISK OF ASPHYXIATION!
-DO NOT OPERATE IN AN
ENCLOSED AREA. USE THIS
PRODUCT ONLY IN WELL
VENTILATED AREAS!
-THE EXHAUST FROM THE
ENGINE CONTAINS CARBON
MONOXIDE, A POISONOUS,
ODORLESS AND INVISIBLE
GAS. BREATHING THIS GAS
CAN CAUSE SERIOUS INJURY,
ILLNESS & POSSIBLE DEATH.
ENGINE FUEL TANK:
1. Review "Fire & Ventilation Precautions" pg. 4, before fueling.
2. Locate the Safety Decals on your unit and heed their warnings.
3. A minimum of 86 octane fuel is recommended for use with this unit. DO
NOT MIX OIL WITH GASOLINE.
4. Purchase fuel in quantities that may be used within 30 days. Use of clean,
fresh lead free gasoline is recommended. Leaded gasoline may be used
if lead-free is unavailable. DO NOT use gasoline containing methanol or
alcohol.
5. Check the engine oil level before starting the engine. (See Engine
manual.)
6. Fill the fuel tank according to accompanying engine manual instructions.
7. Occasionalcarburetorandchokeadjustmentswillbenecessaryfortheengine.
Refer to the engine manual supplied with this unit for proper adjustment
procedures.
8. Review the engine manual accompanying this pressure washer for
correct engine start-up and maintenance procedures.

Mi-T-MCD-GASOLINE Operator's Manual 13
INSTALLATION & PREPARATION
NOZZLE REVIEW:
Various nozzles may be quick-connected into the end of the wand to change
the spray pattern or use the detergent feature. When using Quick Connects
(Q.C.), be certain the connection is securely locked. If not, the high pressure
water may shoot the nozzle from the wand, causing severe injury or serious
damage. To determine spray fan, refer to the actual number stamped on
the nozzle. The rst two digits indicate the spray fan in degrees, i.e.; 00=0°,
15=15°, 25=25°, 6540°=detergent/low pressure.
1. The 0° nozzle (RED): This is a blasting nozzle. It delivers a very
concentrated stream of water. Be cautious when using the straight narrow
stream. It is not recommended for use on painted or wood surfaces,
or items attached with adhesive backings. Uses: Removing weeds
from sidewalk cracks, stubborn stains from concrete, masonry, aluminum
and steel, caked mud from equipment, and cleaning lawn mower
undersides.
2. The 15° nozzle (YELLOW): This is a chiseling nozzle. The spray
should be directed at a 45° angle to the surface and used like a scraper
to remove paint, grease and dirt. Uses: Surface preparation (removing
mildew stains and paint chips).
3. The 25° nozzle (GREEN): This is a ushing nozzle. This pattern is best
suited for ushing dirt, mud, and grime. Uses: Wet sweeping leaves from
walks, curbs and driveways, cleaning stable oors, washing swimming
pool bottoms, degreasing engines.
4. The 65° nozzle (BLACK): This is a low pressure detergent application
nozzle. This broad spray pattern distributes solution over vast areas
under low pressure. Uses: Detergent application, misting or rinsing.
WARNING
RISK OF INJECTION CAUSING
SEVERE INJURY!
NEVER LOOK DIRECTLY AT THE
NOZZLE ORIFICE UNLESS IT
IS DISCONNECTED FROM THE
GUN/WAND ASSEMBLY!
QUICK-CONNECT (Q.C.) NOZZLES
CONNECTION OF Q.C. NOZZLES
WARNING
RISK OF SEVERE INJURY!
THE TRIGGER GUN SHOULD
ALWAYS BE LOCKED IN THE OFF
POSITION WHEN NOT IN USE!
QUICK-CONNECTION
NOZZLE CONNECTION:
1. Be certain the trigger gun is locked in the "OFF" position. See WARNING,
right.
2. The nozzle assembly should be disconnected from the gun assembly at
this time. Retract the locking ring on the quick-connect tting to remove
the nozzle.

14 Mi-T-M®CD-GASOLINE Operator's Manual
CHECK WATER INLET STRAINER
INSTALLATION & PREPARATION
THERMAL RELIEF VALVE:
To ensure the water temperature does not exceed acceptable levels, never allow
the pressure washer to operate in the bypass mode (with the unit running and
the trigger gun closed) for more than three minutes.
A "thermal relief valve" has been added to this unit to protect the pump. It
may begin to open and release water if the water temperature in the pump has
exceeded 140°F. This will allow fresh, cool water to enter the system.
WATER SUPPLY:
1. Selecta water supplyhosewhich is aquality grade of gardenhose measuring
at least 3/4" ID and no longer than 50 feet.
2 Checkthewaterinletstrainerto ensure it is cleanandfreeof any obstructions.
Periodic cleaning of the water strainer will help prevent pump problems. As
a strainer becomes obstructed, it restricts proper ow of water to the pump.
This can result in cavitations which will cause premature failure of pump
packings. Using a screw driver, remove the screen; clean or replace with
Mi-T-M #19-0001 if necessary.
3. Connect the hoses:
a. Connect one end of the water supply hose to the water inlet of the
unit.
b. Connect the other end of the hose to your pressurized water supply.
NOTE: Do not use a non-pressurized water supply (i.e. from a pond or well)
with this unit.
c. Quick-connect the high pressure discharge hose to the water outlet of
the unit.
4. Follow the incoming water requirements listed below:
a. Water pressure must be a minimum of 20 pounds per square inch (PSI)
and a maximum of 125 PSI. (A typical outdoor faucet will generally
supply this PSI if turned completely "ON".)
b. IncomingGPMmustbe approximatelyonegallonmore than the outgoing
GPM stated on the pressure washer nameplate. (You can check GPM
by timing how long it takes to ll a 5 gallon container.)
c. Incoming water temperature must not exceed 125°F. Excessive pump
damage may result if the water temperature exceeds this acceptable
level.
5. Never allow the unit to operate without the incoming water line attached and
the water supply completely turned on.
UNLOADER:
The unloader on your machine is equipped with an adjustment knob so you
can adjust the pressure. Should less pressure be required, simply turn the
adjustment knob counterclockwise. To set back to maximum, turn adjustment
knob completely clockwise. DO NOT OVERTIGHTEN!
CAUTION
RISK OF UNIT DAMAGE!
DO NOT OVERTIGHTEN THE
UNLOADER. BREAKAGE WILL
RESULT IN IMMEDIATELOSSOF
WATERPRESSUREANDCOSTLY
REPAIRS.

Mi-T-MCD-GASOLINE Operator's Manual 15
INSTALLATION & PREPARATION
PRE-START INSPECTION PROCEDURES:
Before starting the unit, perform the following procedures:
1. Check the oil level in the pump and engine.
2. Inspect the inlet water strainer. Clean or replace if necessary. See
"Water Supply", #2, pg. 14.
3. Check all hose connections to ensure they are securely tightened. See
"Water Supply", #3, pg. 14.
4. Inspect for system fuel leaks. If a fuel leak is found, DO NOT START
UNIT! See "Fire & Ventilation Precautions", #2 and #4, pg. 4. Be sure
that all damaged parts are replaced and that the mechanical problems
are corrected prior to operation of the unit. If you require service, contact
Mi-T-M Customer Service.
5. Inspect high pressure hoses for kinking, cuts and leaks. If a cut or leak
is found, DO NOT USE HOSE! Replace hose before starting unit. See
"Miscellaneous Safety Precautions" #6, pg. 6. Be sure that all damaged
parts are replaced and that the mechanical problems are corrected prior
to operation of the unit. If you require service, contact Mi-T-M Customer
Service.
END OF PREPARATION INSTRUCTIONS
WARNING
THE FOLLOWING PAGES CONTAIN OPERATING AND
MAINTENANCE INSTRUCTIONS
DO NOT ATTEMPT TO OPERATE THIS PRESSURE WASHER UNTIL
YOU HAVE READ AND UNDERSTOOD ALL SAFETY
PRECAUTIONS AND INSTRUCTIONS LISTED IN THIS MANUAL.
INCORRECT OPERATION OF THIS UNIT CAN CAUSE SERIOUS
INJURY!!
DO NOT ALTER OR MODIFY THIS EQUIPMENT IN ANY MANNER!

16 Mi-T-M®CD-GASOLINE Operator's Manual
DANGER
RISK OF INJECTION CAUSING
SEVERE INJURY!
-KEEPCLEAROFNOZZLE!NEVER
PLACE HAND OR FINGERS IN
FRONT OF NOZZLE!
-DO NOT DIRECT DISCHARGE
STREAM AT PEOPLE OR PETS!
-BE CERTAIN THE NOZZLE
IS SECURELY CONNECTED
TO THE WAND TO PREVENT
ACCIDENTAL DISCHARGE!
CAUTION
RISK OF DAMAGE.
DONOTALLOWSPRAYPATTERN
TO REMAIN ON A FIXED AREA
FOR AN EXTENDED PERIOD OF
TIME. POSSIBLE DAMAGE MAY
OCCUR TO THE AREA.
OPERATING INSTRUCTIONS
PRIMING THE PUMP:
1. It is essential to prime the pump on initial start-up and each time the water
supply is disconnected from the unit after initial use.
2. Lay the high pressure hose out to remove any loops. Water ow will tighten
the hose, creating tight loops if the hose is not straight.
3. Securely connect the gun assembly to the high pressure hose.
NOTE: The nozzle assembly should NOT be connected to the gun assembly
at this time. See "Nozzle Connection", pg. 13.)
4. With the trigger gun locked in the "OFF" position, turn the water supply
completely on. Pointing the gun in a safe direction, unlock the trigger gun
and squeeze the trigger.
5. Low pressure water will begin owing from the hose/gun assembly. This
allows the unit to prime and purge any air from the system. The unit is
primed when water ow is uninterrupted by air.
6. Once the unit is primed, release the trigger and lock the gun in the "OFF"
position. Securely connect the nozzle assembly. (See "Nozzle Connection",
pg. 13.)
START-UP:
1. Refer to the "Safety Precautions" pgs. 4-7 before starting the unit.
2. Locate the Safety Decals on your unit and heed their warnings.
3. With the gun locked in the "OFF" position, point the trigger gun away from
yourself or anyone else.
4. Disengage the safety lock-off on the gun and squeeze the trigger. Low
pressure water will begin owing from the nozzle.
5. BE CERTAIN the trigger gun remains in an open position while starting
the engine. Brace yourself as the gun will kickback from the high pressure
created by the pump once the engine has started.
6. Put your foot on the frame or wheel to steady the unit during engine start-
up. (Refer to the engine manual accompanying this pressure washer for
the correct procedures needed to start the engine.)
7. Once the engine has started, perform the following procedures with the gun
open:
a. Inspect for system water leaks, oil leaks and fuel leaks. If a fuel leak
is found, TURN UNIT OFF IMMEDIATELY! See "Fire & Ventilation
Precautions", #2 and #4, pg. 4. Be sure that all damaged parts are
replaced and that the mechanical problems are corrected prior to
operation of the unit. If you require service, contact Mi-T-M Customer
Service.
b. Inspect high pressure hoses for kinking, cuts and leaks. If a cut
or leak is found, DO NOT TOUCH HOSE AT LEAK!!! TURN UNIT
OFF IMMEDIATELY! Replace hose before restarting the unit. See
"Miscellaneous Safety Precautions" #6, pg. 6. Be sure that all damaged
parts are replaced and that the mechanical problems are corrected prior
to operation of the unit. If you require service, contact Mi-T-M Customer
Service.
8. Trigger the gun several times and try adjusting the spray pattern. Be
certain to LOCK the trigger gun in the "OFF" position whenever moving the
adjustable or high/low nozzle, or changing quick-connect nozzles. NEVER
look directly into the nozzle! High pressure water creates a risk of severe
injury!
9. Do not allow unit to operate in bypass mode (with trigger closed) for more
than three minutes without triggering the gun. Failure to follow this simple
rule can cause premature failure of pump packing seals, resulting in costly
pump repair.
10. Because your pressure washer delivers a high pressure spray and a variety
of spray patterns, there are many cleaning jobs that can be done without
the use of detergents. If a cleaning agent is required, see "Cleaning With
Detergents" pg. 17 for the correct procedures.

Mi-T-MCD-GASOLINE Operator's Manual 17
OPERATING INSTRUCTIONS
CLEANING WITH DETERGENTS:
1. Refer to "Detergent Cleaning Precautions" pg. 6 before working with
detergents. Be certain to wear protective safety attire as stated on pg.
12.
2. Prepare detergent solution according to label directions. Never pump
acids, alkaline, abrasive uids or solvents through the unit. Due to the
unknownandoftencorrosivecharacteristicsofmanydetergentscommonly
used in the pressure washer cleaning industry, it is recommended to use
only Mi-T-M detergents with this unit.
3. Connect the detergent hose to the unit as shown on the Feature Page
pertaining to your unit. (Page 8 or 10.)
4. Adjust the amount of detergent desired by locating the adjustment knob
at the end of the clear vinyl hose near the pump head. Turn the knob
completely counterclockwise to set at the maximum siphon rate.
5. Immerse the strainer into the detergent solution to allow detergent to
siphon.
6. Be certain the water supply is completely turned "ON".
7. With the trigger gun locked in the "OFF" position, securely quick-connect
the detergent spray nozzle (#6540° BLACK) into the end of the wand.
NOTE: This injection system is designed to apply detergents under low
pressure only. It will not allow detergent solutions to be introduced
into the system unless the nozzle assembly is in the low pressure
detergent mode.
8. To apply solution; unlock the trigger gun and squeeze the trigger. In a
few moments a detergent/water mixture will exit the low pressure nozzle.
Start spraying the lower portion of the surface being cleaned and move
up, using long overlapping strokes. Applying from the bottom up helps
avoid streaking. Allow to soak briey. DO NOT allow detergent solution
to dry on the surface. (Avoid working on hot surfaces or in direct sunlight
to minimize the chances of the detergent drying, which may result in
damaging painted surfaces.) Be certain to rinse a small section at a
time.
9. To rinse; lock the trigger gun in the "OFF" position, securely quick-
connect the 40° nozzle into the end of the wand. Unlock the trigger gun
and spray. It will take about 30 seconds to purge all detergent from the
line. For best rinsing results, start at the top and work down.
10. Siphon a gallon of water through the low pressure detergent injection
system after each use. This prevents the possibility of corrosion or
detergent residue causing mechanical problems during the next use.
SHUTDOWN:
1. Turn engine "OFF" as directed in the Engine Manual.
2. Turn the water supply "OFF".
3. Pointing the gun in a safe direction, trigger gun momentarily to relieve
any trapped pressure.
4. Once pressure is relieved, disconnect the nozzle assembly.
5. Disconnect and drain gun, wand and hoses.
6. Wipe unit clean and store with gun, wand and hoses in a safe, non-
freezing area.
QUICK CONNECT DETERGENT

18 Mi-T-M®CD-GASOLINE Operator's Manual
STORAGE & MAINTENANCE
SPECIFIC MAINTENANCE
ENGINE: The engine instructions that accompany your unit detail specic
procedures for maintenance of the engine. Following the engine
manufacturer's recommendations will extend engine work life.
PUMP: Change the pump oil after the rst 25 hours of operation. After initial
change, every 3 months or 250 hour intervals are recommended.
If oil appears dirty or milky, changes may be required in greater
frequency. Fill only to the dot on the oil sight glass using Mi-T-M
pump oil #AW-4085-0016. DO NOT overll.
QUICK COUPLERS: There is an o-ring seal inside the female quick-coupler
at the water outlet of your unit. This o-ring will deteriorate or, if
the unit is allowed to pump without the high pressure hose or
nozzle attached, it may be blown out occasionally. Simply insert a
replacement o-ring to correct the leak. (Additional o-rings can be
purchased from your dealer.)
NOZZLES: Water ow through the spray nozzle will erode the orice, making
it larger, resulting in a pressure loss. Nozzles should be replaced
wheneverpressureislessthan85% of the maximum. Thefrequency
of replacement will depend upon such variables as mineral content
in the water and number of hours the nozzle is used.

Mi-T-MCD-GASOLINE Operator's Manual 19
STORAGE & MAINTENANCE
WINTERIZING:
For storage and transportation purposes in subfreezing ambient temperatures,
it will be necessary to winterize this unit. This unit must be protected to the
lowest incurred temperature for the following reasons:
1. If any part of the pumping system becomes frozen; excessive pressure may
build up in the unit which could cause the unit to burst resulting in possible
serious injury to the operator or bystanders.
2. The pumping system in this unit may be permanently damaged if frozen.
FREEZE DAMAGE IS NOT COVERED BY WARRANTY.
If you must store your unit in an area where the temperature may fall below
32°F, you can protect your unit by following the procedure outlined below.
1. Gather the following items:
a. Two 5 gallon containers.
b. One gallon of antifreeze. (Mi-T-M recommends an environmentally safe
antifreeze.)
c. Water supply.
d. Three foot hose, 1/2-3/4 I.D. with a 3/4 inch male garden hose tting.
2. Procedure:
a. To start winterizing, unit must be run and primed according to the "Start-
up Procedures" listed on page 12.
b. After running and priming, shut off the unit and water supply.
c. Relieve system pressure by pointing the trigger gun in a safe direction
and squeezing the trigger until water ow ceases to exit the nozzle.
d. Lock the trigger gun in an OFF position and remove the nozzle.
e. Remove the water supply hose from the unit and attach the 3 foot hose
securely to the inlet connection.
f. Shut off the detergent injector if applicable.
g. Fill one 5 gallon bucket with water.
h. Holding the 3 foot hose in an upright position, completely ll the hose
with water. Then plug the hose outlet with your thumb or nger. Place
the plugged end into the 5 gallon bucket of water.
i. Start the unit. Trigger the gun several times until all the air is worked
out of the system (unit is primed). It may be necessary to adjust the
engine RPM down to an idle to aid in priming.
NOTE: Proper winterizing is based on the recommended manufacturer's
instructions listed on the "Protection Chart" shown on the back label
of most antifreeze containers.
j. With the trigger gun held open, siphon enough water out of the 5 gallon
bucket until there is just enough water left to mix with the antifreeze.
k. Point the wand into the empty container.
l. Trigger the gun until the antifreeze begins to exit the wand. Release
the trigger for 3 seconds, then trigger the gun for 3 seconds. Continue
cycling the gun several times until all the antifreeze mixture is siphoned
from the container.
m. Detach the 3 foot hose from the unit and drain any excess antifreeze
back into the 5 gallon container.
n. Disconnect the hose/gun/wand assembly from the unit and drain any
excess antifreeze back into the 5 gallon container.
o. Store the hose, gun and wand with the unit in a safe area.
p. Store antifreeze solution for next use or dispose of according to state
EPA laws.
3. Optional Procedure:
a. Shut the unit and water supply off.
b. Relieve system pressure by pointing the trigger gun in a safe direction
and squeezing the trigger until water ow ceases to exit the nozzle.
c. Disconnect and drain the hose, gun and wand.
d. Start the unit and allow it to run until all the water exits the unit. Once
the water has stopped owing from the unit, turn off.
NOTE: When using this procedure, caution should be used as ice chips can
form from drops of water which could cause the unit to burst if starting
before completely thawed.
WARNING
RISK OF UNIT BURSTING!
DONOTSTORE/OPERATEUNITIN
A FREEZING ENVIRONMENT!
32˚F 0˚C

20 Mi-T-M®CD-GASOLINE Operator's Manual
TROUBLESHOOTING
SYMPTOM PROBABLE CAUSE
Engine will not start. Various engine problems. Refer to the engine manual
accompanying your unit.
Unit components are frozen. Allow to thaw. If any part of the unit
becomes frozen; excessive
pressure may build up in the unit
which could cause the unit to burst,
resulting in possible serious injury to
the operator or bystanders.
No discharge at nozzle when Inadequate water supply. Ensure hose is 3/4" diameter and
trigger mechanism is squeezed. incoming water supply is turned on.
Kink in water inlet hose. Remove kink.
Low or uctuating pressure. Kink in high pressure discharge hose. Replace kinked high pressure hose.
Water inlet screen obstructed. Remove screen, clean or replace.
Pump sucking air. (Prime eliminated) Tighten all water intake connections
Eliminate leaks in intake line.
Not in high pressure mode. Adjust pressure on the unloader.
Obstructed or worn spray nozzle. Remove, clean, or replace.
Damaged or obstructed valve assy. Remove, inspect, clean or replace.
on pump.
Pump packings worn. Replace packings.
Bypass valve not operating correctly. Repair or replace.
Water is leaking from the "Thermal Water temperature is too high. Do not allow unit to operate in
Relief Valve". the bypass mode (with trigger gun
closed) for more than three minutes.
Defective valve. Replace.
Oil appears milky or foamy. Water in oil. Change pump oil. Fill to proper
level.
Oil leaking from unit. DO NOT USE!!!!! Contact Mi-T-M Service.
Detergent will not siphon into Detergent strainer is not completely Check, submerge if necessary.
Low Pressure Detergent mode. submerged in detergent solution.
Detergent strainer obstructed. Inspect, clean or replace.
Detergent hose cut, obstructed or Inspect, clean or replace.
kinked.
Detergent adjusting knob turned to Open adjusting knob. Refer to
closed position. "Cleaning with Detergents" pg. 17.
Not in Low Pressure mode. Insert 6540° nozzle.
Nozzle assembly is plugged. Clean or replace.
Too many high pressure hose Use one extension maximum.
extensions attached to the water outlet.
Ball & Spring in Venturi stuck. Remove, clean or replace.
Water ows back into detergent Ball & Spring in Venturi reversed, Remove, clean or replace.
container. missing or corroded.
Water ows from the nozzle when the Gun is malfunctioning. Repair or replace.
trigger gun is locked in the "OFF"
position.
REMEDY