Mi-T-M RC-0002-0001 User manual

Mi-T-MPit Cleaner Operator's Manual 1
OPERATORS MANUAL FOR Mi-T-M®
PIT CLEANING SYSTEM
PIT CLEANER ASSEMBLY:
RC-0002-0001
SLUDGE CARRIER:
RC-0003-0001
©Copyright 2005, Mi-T-M Corporation® Form #37-0541-092018
CAUTION
RISK OF INJURY!
READ MANUAL BEFORE OPERATING!
This manual is an important part of the pit cleaning system and must remain
with the unit when you sell it!

2 Mi-T-M®Pit Cleaner Operator's Manual
Table of Contents
INTRODUCTION............................................................................................................................................................. 3
CONTENTS .................................................................................................................................................................... 4
SPECIFICATIONS........................................................................................................................................................... 4
PURPOSE....................................................................................................................................................................... 5
IMPORTANT SAFETY WARNINGS ............................................................................................................................. 6-7
-RISK OF BURSTING ..................................................................................................................................................... 6
-RISK OF INJECTION OR SEVERE CUTTING INJURY................................................................................................ 6
-RISK OF BODILY INJURY ............................................................................................................................................. 7
PIT CLEANER SYSTEM FLOW CHART......................................................................................................................... 8
EXPLANATION OF SLUDGE PUMP OPERATION......................................................................................................... 9
PIT CLEANER ASSEMBLY INSTRUCTIONS ............................................................................................................... 10
OPERATING INSTRUCTIONS.......................................................................................................................................11
REPLACEMENT PARTS ................................................................................................................................................11
PARTS LIST PIT CLEANER.......................................................................................................................................... 12
PARTS LIST SLUDGE CART........................................................................................................................................ 14
STATEMENT OF WARRANTY...................................................................................................................................... 15
WARNING: This product can expose you to
chemicals including carbon monoxide, which is
known to the State of California to cause birth
defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov
WARNING
WARNING: This product can expose you to
chemicals including Lead, which is known to
the State of California to cause cancer and birth
defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov
WARNING

Mi-T-MPit Cleaner Operator's Manual 3
Congratulations on the purchase of your new Mi-T-M Pit Cleaning system! You can be assured your Mi-T-M Pit Clean-
ing system was constructed and designed with quality and performance in mind. Each component has been rigorously
tested to ensure the highest level of acceptance.
This operator's manual was compiled for your benet. By reading and following the simple safety, installation, operation,
maintenance and troubleshooting steps described in this manual, you will receive years of trouble free operation from
your new Mi-T-M Pit Cleaning system. The contents of this manual are based on the latest product information available
at the time of publication. Mi-T-M reserves the right to make changes in price, color, materials, equipment, specications
or models at any time without notice.
! IMPORTANT !
These paragraphs are surrounded by a "SAFETY ALERT BOX". This box is used to designate
and emphasize Safety Warnings that must be followed when operating this Pit Cleaning
system.
Accompanying the Safety Warnings are "signal words" which designate the degree or level
of hazard seriousness. The "signal words" used in this manual are as follows:
DANGER: Indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided MAY
result in minor or moderate injury.
The symbols set to the left of this paragraph are "Safety Alert Symbols". These symbols
are used to call attention to items or procedures that could be dangerous to you or other
persons using this equipment.
ALWAYS PROVIDE A COPY OF THIS MANUAL TO ANYONE USING THIS EQUIPMENT. READ
ALL INSTRUCTIONS BEFORE OPERATING THIS PIT CLEANING SYSTEM AND ESPECIALLY
POINT OUT THE "SAFETY WARNINGS" TO PREVENT THE POSSIBILITY OF PERSONAL
INJURY TO THE OPERATOR.
Once the unit has been uncrated, inspect for signs of obvious or concealed freight damage. If damage does exist, le a
claim with the transportation company immediately. Be sure that all damaged parts are replaced and that the mechanical
and electrical problems are corrected prior to operation of the unit. If you require service, contact Mi-T-M Customer
Service.
CUSTOMER SERVICE
CALL OUR TOLL-FREE NUMBER
for the Sales or Service Center nearest you!
800-553-9053
Please have the following information available for all service calls:
1. Model Number
2. Date and Place of Purchase
INTRODUCTION

4 Mi-T-M®Pit Cleaner Operator's Manual
CONTENTS
Carefully unpack your new Mi-T-M Pit Cleaning system. Check the contents against the packing list. Contact the freight
line if a damage claim is required on any component. The following items are the basic equipment sent with your Pit
Cleaning system.
SPECIFICATIONS
Pit Cleaner Assembly
1. Suction lance
a) Main wand assembly
b) Extension assembly
2. Gun with hose
3. Suction head
4. Flex hose
Sludge Carrier
1. Sludge Carrier Assembly
2. 5 Biodegradable lter bags
MAXIMUM FLOW 50 GPM
MAXIMUM FLOW OF PRESSURE WASHER 5 GPM
MAXIMUM PRESSURE OF PRESSURE WASHER 4000 PSI
MINIMUM FLOW OF PRESSURE WASHER 2 GPM
MINIMUM PRESSURE OF PRESSURE WASHER 1000 PSI
DIMENSIONS L x W x H (Inches)
PIT CLEANER ASSEMBLY 93 x 12 x 4
SLUDGE CARRIER 22 x 29 x 48
NET WEIGHT (lbs.)
PIT CLEANER ASSEMBLY 25
SLUDGE CARRIER 53

Mi-T-MPit Cleaner Operator's Manual 5
The Mi-T-M Pit Cleaning System uses your existing Pressure Washer to operate a high volume Sludge Pump. This
Sludge Pump will move liquids, sludge, and solid debris from the bottom of a pit, through 1 ½” PVC pipe and hose, into
the Sludge Cart where it is deposited into a Filtration Bag. The Filtration Bag may then be disposed of in any manner
compliant with EPA standards.
The Pit Cleaner connects to your Mi-T-M pressure washer in place of its standard gun/lance assembly, and uses the
force of the high pressure water to create a vacuum to remove debris and sludge from the pit. The Pit Cleaner comes
with a #4 nozzle which will work with a variety of pressure washers ranging from 1000-4000 PSI and 2–4 GPM. The Pit
Cleaner has a 1:11 ow ratio; a 3 GPM pressure washer will produce a ow of 33 GPM. The more powerful the pressure
washer, the higher volume of debris is removed from the pit.
NOTE: The actual output volumes will vary with the weight and particle size of the material being removed and the
height and distance that the material is moved. For best results with heavier or larger particles use a pressure
and ow nearer to the high end of the suggested pressure and ow.
The following is a chart showing the relationship of pressure and ow for various nozzles in GPM.
PURPOSE
Nozzle Number 1000 PSI 1500 PSI 2000 PSI 2500 PSI 3000 PSI 3500 PSI 4000 PSI
3.0 1.5 1.8 2.1 2.4 2.6 2.8 3.0
4.0 2.0 2.5 2.8 3.2 3.5 3.7 4.0
4. 2.3 2.8 3.2 3.6 3.9 4.2 4.5
5.0 2.5 3.1 3.5 4.0 4.3 4.7 5.0
5.5 2.8 3.4 3.9 4.3 4.8 5.1 5.5
6.0 3.0 3.7 4.2 4.7 5.2 5.6 6.0
0°Replacement Nozzles
Nozzle Mi-T-M Part #
3.0 18-0149
4.0 18-0045
4.5 18-0111
5.0 18-0046
5.5 18-0010
6.0 18-0047

6 Mi-T-M®Pit Cleaner Operator's Manual
POTENTIAL CONSEQUENCE PREVENTION
IMPORTANT SAFETY WARNINGS
WARNING: When using this product, basic precautions should always be observed, including the following:
READ ALL SAFETY WARNINGS BEFORE USING PIT CLEANING SYSTEM
HAZARD
RISK OF BURSTING Serious injury or death could occur
from bursting.
Serious injurymayoccur ifattempting
to start the unit when frozen.
Serious injury may occur from
exploding accessories if incorrect
system components, attachments
or accessories are used.
Do not use this accessory to pump ammable
material! An explosion could occur from a gas
vapor buildup inside the system.
In freezing temperatures, the unit must always
be warm enough to ensure there is no ice
formation in the accessory. Do not operate
the accessory if it has been in a freezing
environment without rst allowing to thaw.
Use only manufacturer recommended repair
parts for the unit.
Serious injury or death could occur
from high pressure spray penetrating
the skin.
Keep clear of nozzle and spray! Never put
your hand, ngers or body directly over the
spray nozzle.
Never point the high pressure discharge spray
at yourself or anyone else.
SEEK EMERGENCY MEDICAL CARE if the
spray appears to have penetrated the skin!
DO NOT TREAT AS A SIMPLE CUT!!
Do not move the unit by pulling on the hose.
High pressure hoses should be inspected
daily for signs of wear. If evidence of failure
exists, promptly replace all suspect hoses to
prevent the possibility of injury from the high
pressure spray. If a hose or tting is leaking,
NEVER PLACE YOUR HAND DIRECTLY ON
THE LEAK.
NEVER operate the gun with the trigger wired
in the open position. To prevent accidental
discharge, the trigger gun should be securely
locked when not in use.
Before removing the spray nozzle or servicing
the unit, ALWAYS shut off the unit and trigger
the gun to release trapped pressure. (Even
after you shut off the unit, there is high pressure
water left in the pump, hose and gun until you
release it by triggering the gun.)
RISK OF INJECTION OR
SEVERE CUTTING INJURY

Mi-T-MPit Cleaner Operator's Manual 7
RISK OF BODILY INJURY Injury may occur from the unit.
!SAVE THESE INSTRUCTIONS!
POTENTIAL CONSEQUENCE PREVENTION
IMPORTANT SAFETY WARNINGS
READ ALL SAFETY WARNINGS BEFORE USING PIT CLEANING SYSTEM
DO NOT DRINK THE WATER IN THE UNIT!!
This is non-potable water and is not suitable
for consumption.
DO NOT allow children to operate this unit.
DO NOT overreach or stand on unstable
support.
Wet surfaces can be slippery, wear protective
foot gear and keep good footing and balance
at all times.
Know how to stop the unit. Be thoroughly
familiar with controls.
Before servicing,ALWAYS shut off the pressure
washer.
Consult Material Safety Data Sheets for safe
handling of chemicals used with your system,
especially oxidizers and acids.
SEEK EMERGENCY MEDICAL CARE if the
spray appears to have penetrated the skin!
DO NOT TREAT AS A SIMPLE CUT!! Be
prepared to tell a physician exactly what kind
of chemicals you were using by reading the
Material Safety Data Sheet (MSDS) provided
with your chemical.
Never use any solvents, detergents or acid type
cleaners with this unit.
Protective equipment such as gloves and rubber
boots are advisable, especially when using
cleaning detergents.
ALWAYS wear protective goggles when
operating the unit to shield the eyes from ying
debris.
DO NOT direct spray toward fragile materials
such as glass for shattering could occur.
Stay alert-watch what you are doing. Do not
operate the unit when fatigued or under the
inuence of alcohol or drugs.
NEVER squeeze the trigger unless securely
braced.
NEVER trigger the gun while on a ladder or
roof.
DO NOT leave pressurized unit unattended.
Shut off the pressure washer and release
trapped pressure before leaving.
Serious injury can occur from loose
debris being propelled at a high speed
from the spray gun.
Injury may occur if the operator loses
his balance caused by the thrust of
water traveling through the spray
nozzle.
HAZARD

8 Mi-T-M®Pit Cleaner Operator's Manual
High-pressure water ows from the existing Pressure Washer (1) into the Gun/Lance (2) of the Pit Cleaner where it is
directed into the Sludge Pump (3). The high-pressure stream is directed up into the PVC Body (4) of the Pit Cleaner
creating a vacuum (venturi effect) at the bottom opening of the Sludge Pump. This vacuum pulls liquids, sludge, and or
solids from the bottom of the pit into the PVC Body (4) of the Pit Cleaner where it mixes with the high-pressure ow from
the Pressure Washer (1). This mix is then forced out through the back end of the Pit Cleaner and into the PVC Hose
(5), the hose directs the mixed ow into the Sludge Cart (6). The mixed ow is then deposited into the Filtration Bag
where the solids and sludge materials are ltered from the water, and retained in the bag allowing the cleaned water to
return to the pit system.
PIT CLEANER SYSTEM FLOW CHART
PIT-0027-022900-JJ

Mi-T-MPit Cleaner Operator's Manual 9
EXPLANATION OF SLUDGE PUMP OPERATION
High-pressure water ows into the Sludge Pump through a 0° nozzle and is injected into the body of the Pit Cleaner. As
the high-pressure water is owing up the PVC body of the Pit Cleaner a vacuum (venturi action) is formed at the bottom
end of the Sludge Pump. Debris and Sludge from the pit is pulled up into the high pressure stream and out through the
body of the Pit Cleaner.
PIT-0026-113099-JJ

10 Mi-T-M®Pit Cleaner Operator's Manual
PIT CLEANER ASSEMBLY INSTRUCTIONS
PIT-0023-111099-JTR
1. Main Wand Assembly
2. Extension Assembly
3. Sludge Pump Assembly
4. Lance Assembly
1. Screw main wand assembly into extension assembly. Make sure there is an adequate amount of Teon tape on the
male adapter of the main wand assembly.
2. Insert the sludge pump assembly into the coupler on the extension assembly and pull the levers back to lock in
place.
3. Attach the lance assembly to the main wand assembly by pressing the pipe into the clamps until the clamps are
fastened securely (two clicks).
4. Attach the quick connect from the lance assembly to the plug of the sludge pump assembly.

Mi-T-MPit Cleaner Operator's Manual 11
OPERATING INSTRUCTIONS
1. Place the Sludge Carrier on the wash pad so that water will drain to catch basin.
2. Attach one of the Biodegradable lter bags to the Sludge Carrier by pushing the bolts through the burlap weave of
the bag. Make sure all eight bolts are pushed through the bag.
PIT0025-JJ
3. Connect one end of the Flex Hose to the cam lock tting of the Sludge Carrier and the other end to the cam lock
tting on the top of the Pit Cleaner Assembly.
4. Attach the gun of the Pit Cleaner Assembly to the pressure washer with a hose that has a 3/8” female quick-connect
tting.
5. Start the pressure washer
6. To clean the pit, insert the head of the Pit Cleaner Assembly into the sludge at the bottom of the pit and pull the
trigger on the gun.
7. The unit is operating correctly when you can feel a surge of uid through the ex hose and see the sludge dump into
the Biodegradable lter bag.
8. If the unit is not working correctly, check the following causes:
a. The sludge is too thick to pump up the Pit Cleaner Assembly. Move the Pit Cleaner Assembly up and down in
the pit to dislodge the sludge or remove it from the pit to ush out the sludge.
NOTE: The pressure washer must be shut off before checking causes "b-d".
b. An object is lodged in the head of the Pit Cleaner Assembly. Remove the head if necessary to dislodge the
object.
c. Sludge has plugged the Pit Cleaner Assembly or Flex Hose. Undo cam lock ttings and remove obstruction.
d. The nozzle in the head of the Pit Cleaner Assembly is clogged. Remove the head and use a 9/16” socket to
remove and clean out the nozzle.
NOTE: Some debris cannot be removed from the pit. It may be necessary to periodically empty the pit and shovel the
debris out by hand.
9. When a bag is full, stop cleaning the pit and disconnect the hose from the Sludge Carrier and cart it over to a drainage
area. Tie off the bag and remove it from the cart to let it drain. It may take a couple hours to drain the bag.
10. Place the next bag on the Sludge Carrier and continue cleaning, replacing the bag when necessary.
REPLACEMENT PARTS
Biodegradable Filter Bags (Qty. 5) ................................... RC-0003-0002
Replacement O-ring for 1/4” Quick Connect .................... 25-0123
Repair Kit for Gun............................................................. 70-0055

12 Mi-T-M®Pit Cleaner Operator's Manual
PARTS LIST PIT CLEANER
RC-0002-0001-113099-JJ

Mi-T-MPit Cleaner Operator's Manual 13
RC00020001-113099-JJ
PIT CLEANER
R E F. # DESCRIPTION PART# Q T Y. R E F. # DESCRIPTION PART# Q T Y.
1Main Wand Assembly N/A 117 Sludge Pump 50-0163 1
2Adapter-Cam & Groove 55-0024 118 Lance Assembly N/A 1
3Adapter-Female 55-1621 219 Quick Connect Plug 17-0005 1
4Pipe-1 1/2" *(6.18' required) 55-1600 120 Trigger Gun 16-0001 1
5Cap - 1" 55-1238 121 Pipe Clamp 42-0026 2
6Pipe-1" *(.68' required) 55-1200 122 Locknut 30-5202 2
7Te e 55-1603 123 Washer 28-0121 4
8Adapter-Male 55-1622 224 Bolt 27-5016 2
9Extension Assembly N/A 125 Lance 16-0380A01 1
10 Coupler-Cam & Groove 55-0060 126 Hose 15-0216 1
11 Gasket (with 55-0060) 25-0481 327 Quick Coupler Socket 17-0001 1
12 Sludge Pump Assembly N/A 128 Hose Assembly N/A 1
13 Quick Connect Plug 17-0002 129 Coupler 55-0053 2
14 Reducer 23-0017 130 Flex Hose (20') 15-0212 1
15 Adapter-Cam & Groove 55-0061 1*Must order in one foot lengths.
16 Nozzle-0004 18-0045 1

14 Mi-T-M®Pit Cleaner Operator's Manual
PARTS LIST SLUDGE CART
RC-0003-0001-022800-JJ
RC-0003-0001-022800-JJ
SLUDGE CART
R E F. # DESCRIPTION PART# Q T Y. R E F. # DESCRIPTION PART# Q T Y.
1Sludge Cart 5-0166-A01 1 8 Gasket 25-0481 1
2Plug 62-0125 3 9 Filter Bag-Burlap 41-0190 5
3Elbow Fitting 55-1610 110 Wheel 14-0017 2
4Adapter 55-0024 111 Nut 30-0117 2
5Pipe *(.23' required) 55-1600 112 Handle Grips 7-0143 2
6Fitting 55-1622 1*Must order in one foot lengths.
7Fitting 55-1686 1

Mi-T-MPit Cleaner Operator's Manual 15
STATEMENT OF WARRANTY
Mi-T-M warrants all parts (except those referred to below) of your new Pit Cleaning system
to be free from defects in materials and workmanship for One (1) Year from the date of
original purchase.
Defective parts not subject to normal wear and tear will be repaired or replaced at Mi-
T-M's option during the warranty period which upon examination is disclosed to have
been defective in material or workmanship. In any event, reimbursement is limited to the
purchase price paid.
EXCLUSIONS
1. Normal wear parts:
-Quick Connects
-Nozzles
-Trigger Gun Valve Assembly
2. This warranty does not cover parts damaged due to:
-normal wear, misapplication, modications/alterations, abuse,
-operation at other than recommended speeds, pressures or temperature,
-the use of caustic liquids,
-chloride corrosion or chemical deterioration,
-uctuations in electrical or water supply,
-operating unit in an abrasive, corrosive or freezing environment.
3. This warranty does not cover parts damaged by failure to follow recommended:
-installation, operating and maintenance procedures.
4. This warranty does not cover the cost of:
-normal maintenance or adjustments,
-labor charges,
-transportation charges to Service Center,
-freight damage.
5. The use of other than genuine Mi-T-M parts will void warranty. Parts returned, prepaid
to Mi-T-M's factory or to an Authorized Service Center will be inspected and replaced
free of charge if found to be defective and subject to warranty. There are no warranties
which extend beyond the description of the face hereof. Under no circumstances
shall Mi-T-M bear any responsibility for loss of use of the unit, loss of time or rental,
inconvenience, commercial loss or consequential damages.
For Service or Warranty consideration, contact
Mi-T-M Corporation, 50 Mi-T-M Drive, Peosta, IA 52068-0050
563-556-7484 / 800-553-9053 / Fax [phone]
Monday-Friday 7:30 a.m. - 5:00 p.m. CST

16 Mi-T-M®Pit Cleaner Operator's Manual