MicroConnect HB-102A User manual

1
1X2 4K60HZ HDMI 2.0
HDBASET SPLITTER
Quick Installation Guide
Ver. 1.0
All brand names and trademarks are properties of
their respective owners
2
INTRODUCTION:
FEATURES:
34
● Advanced HDBaseT technology offering uncompressed video and audio with
zero latency
● Features 1x HDMI input that is replicated to 1x HDBaseT outputs
● Features 1x HDMI loop out for integrating local displays or cascading to
multiple devices
● Supports 4K 60Hz 4:4:4 UHD video up to 70m via cat6a cable
● Extends HDMI 1080p video up to 100m via cat6a cable
● Supports all known HDMI audio formats including Dolby TrueHD, Dolby
Atmos, Dolby Digital Plus and DTS-HD Master Audio transmission
● HDMI audio breakout to both Optical and coaxial digital outputs concurrently
● Supports PoE (Power over HDBaseT) to power compatible HDBaseT
receivers
● Compatible with the HDBaseT receivers - ET-13S-RX (4K 60Hz 4:4:4)
● Advanced EDID management
● HDCP2.2 compliant
Our HB-102A 4K HDBaseT splitter distributes a single HDMI 2.0 4K 60Hz 4:4:4
source to One simultaneous HDBaseT outputs. The HB-102A splitter utilizes
technology to deliver HDMI, Bi-directional IR and PoH (PoE) up to lengths of
100m (70m 4K 60Hz 4:4:4) over a single CAT6a cable. The 2-Way splitter also
features audio breakout, EDID management, and HDMI loop out for integrating
local displays or cascading to multiple devices.
● 1 x HB-102A
● 1 x 48V/0.5A DC power supply
● 1 x IR emitter (IRE)
● 1 x IR receiver (IRR)
● 1 x User manual
PACKAGE CONTENTS:
① IR In: plug the IR receiver into this jack
② IR Out: plug the IR blaster into this jack
③ Power indicator: constant blue color when the device is powered on
④ HDMI Input indicator: constant blue color when a HDMI source is connected
⑤ HDMI output indicator: constant blue color when a HDMI output is connected
⑥ HDBaseT out indicator: constant blue color when HDBaseT receiver is
connected
⑦ RS232 port
⑧ EDID DIP switch - used for global EDID settings
① HDMI input - connect to a HDMI source
② Coaxial audio out - RCA connector, de-embedded audio from the HDMI input
③ Optical out - Connect audio equipment
④ HDMI output - connect to a HDMI display or additional HDMI distribution
equipment
⑤ HDBaseT outputs - connect to HDBaseT receivers
⑥ DC 48V 0.5A
PRODUCT OVERVIEW:
Rear Panel :Front Panel :
RS232 EDIDIR In IR Out Power HDBaseT OutHDMI OutHDMI In HDBaseT OutHDMI In Coaxial Optical HDMI Out 48V
④ ⑤ ⑧⑦② ③① ⑥ ④ ⑤② ③① ⑥
Attention:
Customer need to buy the receiver separately

SPECIFICATIONS:
CONNECTION AND OPERATION:
EDID CONTROL :
EDID (Extended Display Identification Data) is a data structure that is used
between a display and a source. This data is used by the source to find out what
audio and video resolutions are supported by the display. By pre-determining
the video resolution and audio format of the source and display device you can
reduce the time need for EDID handshaking thus making switching quicker
and more reliable.
The configuration of HB-102A splitter EDID settings is achieved by using EDID
dip-switches located on the rear of the splitter - See below
5 6
78
● Video input : 1x HDMI Type A female
● Video output : 1x HDBaseT RJ45 connector, 1x HDMI Type A female
● Audio output :1x Optical & 1x digital coaxial
● PoH (Power over HDBaseT) supplied to compatible Blustream HDBaseT
receivers from the splitter
● IR input : 1x 3.5mm stereo jack
● IR output : 1x 3.5mm mono jack
● EDID : 16-bit potentiometer switch
● Power : 48V/0.5A DC
● Operating temperature : 32°F to 104°F (0°C to 40°C)
● Storage temperature : -4°F to 140°F (-20°C to 60°C)
● Compatible with (HDBaseT Receivers) : ET-13S-RX (4K 60Hz 4:4:4 maximum
output)
NOTE: Specifications are subject to change without notice. Weights and
dimensions are approximate.
MAINTENANCE:
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or benzene
to clean this unit. Components inside this unit are not user serviceable. Do not
remove the protective cover from the unit. Removing any panel from this
product will invalidate the manufacturer's warranty.
HD TV HD TV
Speaker
IR BlasterIR Receiver
HDMI Source
PS3,PC,STB,
Blu-ray DVD player etc
HDMI In
HDMI Out HDMI Out
RS232 Equipped
PC or Notebook
RS232 Cable
HDMI Cable
CAT6a Cable
RS232 Cable
CAT6a
Global EDID Setting
RS-232 linked images
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
EDID_BYPASS_HDBT
EDID_BYPASS_HDMI
1080P_2CH
1080P_8CH
4K60HzY420_3D_2CH
4K60HzY420_3D_6CH
4K60HzY420_3D_8CH
4K60HZ_3D_2CH
4K60HZ_3D_6CH
4K60HZ_3D_8CH
4K60Hz_3D_2CH_HDR
4K60HZ_3D_6CH_HDR
4K60Hz_3D_8CH_HDR
User_EDID
Copy_Tx_EDID
CASMode_SET
COPY HDBT EDID,DEFAULT HDBT OUTPUT1
COPY HDMI EDID,DEFAULT HDMI OUTPUT1
1080P AND 2 CHANNEL AUDIO
1080P AND 7.1 CHANNEL AUDIO
4K 60Hz,YUV4:2:0,3D AND 2 CHANNEL AUDIO
4K 60Hz,YUV4:2:0,3D AND 6 CHANNEL AUDIO
4K 60Hz,YUV4:2:0,3D AND 7.1 CHANNEL AUDIO
4K 60Hz,3D AND 2 CHANNEL AUDIO
4K 60Hz,3D AND 6 CHANNEL AUDIO
4K 60Hz,3D AND 7.1 CHANNEL AUDIO
4K 60Hz,3D,2 CHANNEL AUDIO AND HDR
4K 60Hz,3D,4 CHANNEL AUDIO AND HDR
4K 60Hz,3D,7.1 CHANNEL AUDIO AND HDR
EDID CAN BE SET BY USER
COPY OUTPUT EDID,PRIORITY COPY THE
EDID OF OUTPUT1 TO USER EDID (ONLY
COPY ONCE). THE OUTPUT AND INPUT
INDICATORS WILL FLASH THREE TIMES IF
COPY SUCCESSFULLY.
CAS MODE ENABLE,multiple product are used
in tandem stacking, setting it to this mode will
result in better compatibility.
EDID TYPE REMARKS
SWITCHING
POSITIONS
RX
RX