Microh LEDP38 User manual

LEDP38 AND LEDP38RSD
Operating Manual
Thank you for purchasing the LEDP38 RGB colour mixing LED Par. This unit has great output and has
been designed for use in Nights Clubs, Stage, Truss warmers and much more. This unit is controlled via
DMX 512 allowing the user to control it with other existing DMX lights.
Connection
This unit is connected using standard XLR 3 pin cable. To connect the signal cable(XLR), plug one side
into “ IN” socket in the back of light and other side into “ OUT” signal connector in the DMX512 board,
(signal input: 1=>Ground, 2=>data-, 3=>data+ ). Power supply for this unit is 120V – 220V switch able.
This unit requires 15W (.13amp) power which allows the user to connect up 100 units on one 15amp circuit.
Function
This unit has several operation modes, Stand Alone, Master Slave and DMX.
Stand Alone Mode :7 colour change/7 colour strobe/7 colour Automatic changing /7 colour automatic
fade in and fade out / sound colour changing.
Master Slave Mode – All units will perform the same function. One unit is set as the master and others
are set as the slave and will perform all the functions of the master unit giving the units a pre
programmed look. The units must be connected to each other via XLR cables.
DMX 512 Mode: In this mode each unit will be set to a DMX value and controlled by using a DMX
controller.
Note
This unit has been designed for Indoor use. Operating temperature: -20—45℃, humidity：0％－90％
Function
Stand Alone（Dip switch as below）●means “on” status。◎ means “OFF”status
function №1 №2 №3 №4 №5№6 №7 №8 №9№10
1 red ●◎◎◎◎◎◎◎◎◎
2 green ◎●◎◎◎◎◎◎◎◎
3 blue ◎◎●◎◎◎◎◎◎◎
4 strobe Speed
1
Speed
2
Speed
3
Speed
4 ●Red:off/on Green:
off/on Blue: off/on ◎◎

LEDP38 AND LEDP38RSD
5
fade in
and fade
out
Speed
1
Speed
2
Speed
3
Speed
4 ◎●◎◎◎◎
6 Auto. Speed
1
Speed
2
Speed
3
Speed
4 ◎◎●◎◎◎
7
Sound
activated
strobe
◎◎◎◎◎◎◎◎●◎
8
Sound
activated
color
change
●◎◎◎◎◎◎◎●◎
Remarks: Dip switch 1. 2. 3 “on” will run 7 colour, Dip switch 7, 8 “on” will adjust the music sensitivity via
potentiometer knob. Speed 1 means slowest , Speed 4 means fastest.
Master and slave (dip switch as below):
Master light: dip switch same as Stand Alone Mode, all slave lights: Dip Switch NO.1 and
NO.10 ”ON”, NO2-NO9 to “ OFF” status
DMX-512 Mode
Dip Switch“10” to “ ON” to receive DMX signal, 1-9 are selectable code, refer below:
●means “ on” status
№1 №2 №3 №4 №5 №6 №7 №8 №9 №10
1 2 4 8 16 32 64 128 256
●
Channel Assignment
This light has 4 DMX512 channels, please reference the below function channels:
Ch1: function selecting:
0-127 dimmer ( Ch2-Ch4 dimmer valid )
128-250 strobe (Ch2-Ch4 dimmer valid)
251-255 LIGHT ON(Ch2-Ch4 valid)
CH2: 0-255 all Red dimmer
CH3: 0-255 all Green dimmer
Ch4: 0-255 all Blue dimmer
Specification
1．Input power:AC100～240V/50-60Hz
2．Total power: 15W
3．10mmLEDs: 90pcs (red / 30pcs, blue / 30pcs, green / 30pcs ) (Angle:30°)
4．House size：18×17.5×17.5cm
5．Net/weight：0.8Kg
6．Gross/weight：1.3Kg
7．Shipping size：( 6pcs/master carton): 57×27×39cm
8．Gross/weight：8Kg
function №1 №2 №3 №4 №5№6 №7 №8 №9№10