MICROMATIC 941-094 User manual

DEDICATED TO
DRAFT QUALITY
NEW ”HOLDER”
FINGER
REPLACEMENT OF HOLDER AND
FINGER FOR TOOL NO. 941-094
HOLDER/FINGER
FOR 941-094

2 |MICRO-MATIC.COM
Fig. 1
Fig. 2
Fig. 3
FOR TOOL 941-094
HOLDER AND FINGER
Release the set screw.
Pull off the outer tube.
REPLACEMENT OF “HOLDER AND FINGER”
New ”Holder” with
new ”Finger”
Old ”Holder” with
old ”Finger”

MICRO-MATIC.COM |3
Fig. 4
Fig. 5
Fig. 6
1
2
Remove the 1st pin.
Turn the tool 180° and remove the 2nd pin.
Release the set screw.
FOR TOOL 941-094
HOLDER AND FINGER

4 |MICRO-MATIC.COM
Fig. 7
Fig. 8
Fig. 9
FOR TOOL 941-094
HOLDER AND FINGER
Pull out the handle bar.
Remove the plastic plug.
Release the set screw.

MICRO-MATIC.COM |5
Fig. 10
Fig. 11
Fig. 12
Pull out the 3rd pin.
Release the set screw for venting tap.
Release the venting tap.
FOR TOOL 941-094
HOLDER AND FINGER

6 |MICRO-MATIC.COM
Fig. 13
Fig. 14
Fig. 15
FOR TOOL 941-094
HOLDER AND FINGER
Pull out the 4th pin.
Release the set screw.
Remove the 5th pin.

MICRO-MATIC.COM |7
Fig. 16
Fig. 17
Fig. 18
Remove the old “holder with nger” from the tool.
Align the holes.
Turn the tool anti-clock wise 180°.
FOR TOOL 941-094
HOLDER AND FINGER

8 |MICRO-MATIC.COM
Fig. 19
Fig. 20
Fig. 21
FOR TOOL 941-094
HOLDER AND FINGER
Put in the new “holder with nger”.
Mount the Allen key on the “holder with nger”.
Slide-in the “holder with nger” and place it in the
square hole.

MICRO-MATIC.COM |9
Fig. 22
Fig. 23
Fig. 24
Insert the 5th pin. (xxx mm long)
(You are still having the Allen key in the “holder with
nger”).
Tighten the set screw.
Place the 4th pin. (xxx mm long).
FOR TOOL 941-094
HOLDER AND FINGER

10 |MICRO-MATIC.COM
Fig. 25
Fig. 26
Fig. 27
FOR TOOL 941-094
HOLDER AND FINGER
Tighten the set screw.
Put in the venting tap.
Place the 3rd pin.

MICRO-MATIC.COM |11
Fig. 28
Fig. 29
Fig. 30
Tighten the set screw.
Place the 2nd pin in the rst hole.
Turn the tool anti-clock wise 180° and place the 1st
pin in the second hole.
FOR TOOL 941-094
HOLDER AND FINGER

12 |MICRO-MATIC.COM
Fig. 31
Fig. 32
Fig. 33
FOR TOOL 941-094
HOLDER AND FINGER
Recommended grease.
Grease all grooves and pin holes.
Slide in the outer tube.

MICRO-MATIC.COM |13
Fig. 34
Fig. 35
Fig. 36
Tighten the set screw.
Slide in the handle bar.
Tighten the set screw.
FOR TOOL 941-094
HOLDER AND FINGER

14 |MICRO-MATIC.COM
Fig. 37
FOR TOOL 941-094
HOLDER AND FINGER
Put on the plastic plug.

MICRO-MATIC.COM |15
Fig. 38
Fig. 39
Fig. 40
Old “Finger”
Release the set screw.
Pull off the outer tube.
FOR TOOL 941-094
FINGER
REPLACING OF “FINGER” FOR SERVICE TOOL
Old ”Holder” with
old ”Finger”
New ”Holder” with
new ”Finger”

16 |MICRO-MATIC.COM
Fig. 41
Fig. 42
Fig. 43
FOR TOOL 941-094
FINGER
Turn the inner tube so the two screws are visible and
unscrew them both.
Pull out the “Finger”.
The tool is ready to have its “Finger” replaced.

MICRO-MATIC.COM |17
Fig. 44
Fig. 45
Fig. 46
Insert the new “Finger”.
Turn the inner tube so the two screws are visible and
in-screw both.
Put on outer tube.
FOR TOOL 941-094
FINGER

18 |MICRO-MATIC.COM
Fig. 47
FOR TOOL 941-094
FINGER
In-screw the set screw.

MICRO-MATIC.COM |19
NOTES

MICRO MATIC A/S |Holkebjergvej 48 |DK-5250 Odense SV |Denmark |micro-matic.com
MAR-3103-090517