Midian Electronics ANI-F Maxon User manual

1
ANI-F Maxon
Multi-Format ANI Encoder
Manual Revision: 04-08-25
Covers Software Revisions:
ANI-F: 1.0
SPECIFICATIONS
Operating Voltage 9.8 VDC
Operating Current 2.6 mA
Operating Temperature -30 - +60 C
Frequency Range 280-3600 Hz
Audio Output Level 1 V (RMS)
Audio Output Impedance 22 KΩ
PTT Output Current 200 mA
Tone Distortion <1%
ABOUT THE ANI-F
The ANI-F offers ANI & Emergency ANI encoding
tone signaling formats such as Motorola’s MDC-
1200 & MDC-600, M/A-Com’s G-Star, DTMF, 5-
tone, 2-tone, ANI with Status, or Burst Tone. A
special POCSAG paging version is also available.
The ANI-F can be used with Midian’s CAD or DDU
Series products for monitoring ANI and ENI
transmissions.
PRODUCT PROGRAMMING
Midian’s ANI-F Maxon is programmed via Midian’s
KL-3 programmer. Please reference the KL-3
manual for setup instructions of the KL-3 software
and hardware. From the product selection screen
on the KL-3 UP software, select the appropriate
product name from the list and click OK.
Set the parameters of the ANI-F Maxon software to
fit the application. If any clarifications on a feature
are required, move the mouse cursor over the
feature name until the question mark appears and
right click, a definition of the feature will be shown.
After entering the parameters, save the file by going
to File - Save As. Enter the file name in the File
Name block and click Save. Saving the file will allow
for quick and easy reprogramming of units.
After plugging the board into the radio, but with the
radio still open (see next section), connect the black
lead of the KL-3 to a common ground, the yellow clip
lead to Program Out pad, and the green clip lead to
the Program In pad. Ground the PTT Input, apply
power to the radio and click “Program Unit” in the
KL-3 software. Follow the same procedure to read
the unit, but select “Read Unit” in the menu bar.
HARDWARE INSTALLATION
Be certain to follow standard anti-static procedures
when handling any of Midian’s products.
SP-120/130/140/310/320/330/340/SL-55/55+: Open
the radio, following the instructions detailed in the
Maxon radio manual. The following table lists the
factory settings of the radio links and how they
should be configured for installation of the Midian
board. Once the link positions are correct, plug the
Midian board onto the options connector labeled
CON404, and then reassemble the Maxon radio.
For the SP-300 Series it will be necessary to keep
LK14 out and insert LK19.
LK # Factory ANI-F
LK1 Out Out
LK2 In In
LK3 In In
LK4 In Out
LK5 In In
LK6 Out Out
LK7 In In
LK8 Out Out
LK9 Out Out
LK12 In In
LK14 Out In
LK15 Out Out
LK16 In In
LK17 Out Out
LK18 Out Out
LK19 Out Out
LK20 Out Out
LK21 Out In
LK22 Out Out
SM-2000 Series & PM-100/160: Open the radio,
following the instructions detailed in the Maxon radio
manual. The following table lists the factory settings
of the radio links and how they should be configured
for installation of the Midian board. Once the link

2
positions are correct, plug the Midian board onto the
options connector labeled CON404, and then
reassemble the Maxon radio.
LK # Factory ANI-F
LK1 Out Out
LK2 Out Out
LK3 In In
LK4 In Out
LK5 In In
LK6 Out In
LK7 Out Out
LK8 Out Out
LK9 Out Out
LK10 Out Out
LK11 In In
LK12 Out Out
LK13 In In
LK14 In In
LK15 Out Out
LK16 Out Out
LK17 In In
LK18 Out Out
LK19 Out Out
It will also be necessary to insert LK2 and remove
LK4 in the front panel if using the auxiliary switch for
Emergency ANI.
HARDWARE ALIGNMENT
For the TX Audio Output in a wide band system, set
the ANI modulation pot R12 to 3.3 KHz (66% of 5
KHz) of deviation per EIA specifications. For the TX
Audio Output in a narrow band system, set the ANI
modulation pot R12 to 1.65 KHz (66% of 2.5 KHz) of
deviation per EIA specifications.
RADIO PROGRAMMING
Other than the link positions noted under hardware
installation, no special programming is necessary.
TECHNICAL NOTES
Portable Radio Emergency ANI: The transmission
of the Emergency ANI is accomplished with the
momentary options button, the bottom side button.
Mobile Radio Emergency ANI: The transmission
of the Emergency ANI is accomplished with the
latched auxiliary button. Since it is a latched button,
it will be necessary to push the auxiliary button again
to ready the button for another emergency.
Common/Non-Common PTT: If Common PTT is
to be used, it will be necessary to insert LK4 and
program the ANI-F for common PTT.
SP-300 Alert Tone: In the SP-300 Series, it may be
necessary to install a wire from the ANI-F Maxon’s
Pin 7 (Alert Tone) to the radio’s + speaker terminal.
OPERATION
ANI Encode: When the PTT Input is grounded, the
unit will assert the PTT Output and send the
programmed ANI tones out the TX Tone Output.
ENI Encode: When the Emergency Input is
grounded, the unit will assert the PTT Output and
send the programmed Emergency ANI tones out the
TX Tone Output.
MIDIAN CONTACT INFORMATION
Midian Electronics Inc.
2302 East 22nd Street
Tucson, Arizona 85713 USA
Orders: 1-800-MIDIANS
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
Web: http://www.midians.com/