Miele KM 360 G User manual

Installation Instructions
Gas cooktop
KM 360 G
To prevent accidents and
machine damage,
read these instructions
before installation or use, M-Nr, 06 390 460

= Donotstoreorusegasolineorotherflammable
vaporsandJiquidsinthevicinityof thisorany
otherappliance.
=WHAT TO DO iF YOU SMELL GAS
® Do not try to Jight any appliance.
® Do not touch any etectricaJ switch.
® Do not use any phone in your building.
®immediately call your gas supplier from a
neighbor's phone. Follow the gas supptier's
instructions.
®mfyou cannot reach your gas supplier, call the
fire department.
mnstaHationand service must be performed by a
qualified installer, service agency or the gas
supplier.
(ranMassachusetts a ticensed plumber /gas fitter)
Note to the installer:
PJease teave this instruction book with the
consumer for the tocat electrical / gas inspector's
use,

Contents

_iii}ii_i_i_i_iiiiiii_i_ii_i_i_i_ii_i_i`_`i_J_i_iii_iiiiiiiiiiiiiH_iiHiiiiii_i_i_i_`ii_i_iii_iii:_:_:_i_i_i!_ii_iii:iii_i_`_ii`iiiiii_i_iii_i_ii_i_i`i`i_i_iii_i_i_iii_HHiiiii_iii!_i_ii_i_i_i_iii_iii_i_ii:ii_i_iiii_iiiiiiii!i!ii_i_`i_i_`Xi`iiiiiii_i_i_i_ii_ii`ii_i_ii_i_ii_ii:i_iii`i_i_iii_i_iii_i_iii_i_ii_i_i`ii_iiiiiiiii!i_i!i_ii!i_iii`iii_i_i_i_iii!_i_i!_i!_iii!_i_ii_ii_i_`_ii`ii_i_iiiHii_iiii!iiii_i_iii_iiiiiii!_i!_i_:i_ii_:iii!`i_!_iiii_i_i_:ii_iii_`iii_i_i_i_i_i_i_:ii_iiiiiiiii_i_iii_ii_:_i_i_iii_
_MPORTANT SAFETY _NSTRUCT_ONS
installation
these Installation Instructions must
be observed in order to ensure safe
operation, Failure to do so increases
the risk of fire,
The cabinetry and venting hood
should be installed first, to prevent
damage to the cooktop.
Gas appliances should only be
}installed in a well ventilated area,
Theoountertopmustbebonded
with heat resistant (212°F/100°C)
adhesive to prevent distortion or
dissolving,
The cooktop should only be
,nstalledasshown,while
maintaining the required safety
distances shown, Do not install the
cooktop between two tall cabinets, this
is a fire hazard.
This equipment has not been
designed for maritime use or for
use in mobile installations such as
aircraft or recreational vehicles,
However, under certain circumstances
it may be possible for installation in
these applications, Please contact the
Miele Technical Service Department
with specific requirements,
2:W'
recommended
i i_ii:i_iiI
2 3/4
not recommended
not allowed

Appliance dimensions
40mm
(_ Built in depth
'_#Electrical connection box
,:s}Gas connection R 1//,NPT
[] When making the cut-out regard the minimum distance of 2 s/4"(70 mm) to the
rear wall and 4" (100 mm) to the left and right side,
See "IMPORTANT SAFETY INSTRUCTIONS" for more information,

installation
Setting the cooktop into p_ace
[] Screw the gas regulator onto the
nipple underneath the cook,top. See
"Gas connection - Gas pressure
regulator".
Securing the cooktop
i for the regulator does not exist ......
directly under the cook,top, it may be
moved closer to the shut off valve.
[] Guide the power cord through the
cut-out.
[] Set the cook,top in the cut-out and
center iL
[] Secure the cooktop in position with
the supplied fixing brackets, (_.
The cook,top must not be
permanently sealed into the
countertop when installed. !:
The sealing strip under the edge of
the cook,top provides a sufficient !i
seal for the countertop.
If the cooktop is sealed into position,
the countertop or appliance may be
damaged if the cook,top needs to be
removed for maintenance or service.

Electrical connection
three-prong grounding plug to
prevent shock hazards. It should be i:
plugged directly into a properly
grounded outleL Do not cut or
z_WARNING
Disconnect the appliance from the
main power supply before
installation or service. To reduce the
risk of electric shock, make sure that
the appliance is properly grounded
after installation.
Power supply
The automatic ignition requires that the
cooktop be connected to a 120 VAC,
60 Hz power supply. The supply line
should be protected by a 15 A breaker.
Actual power consumption (during
ignition only) is 25 W.
This appliance is equipped with a 4.5 ft.
(1.4 m) long power cord that is ready
for connection to the appropriate outlet.
Please place the power outlet so that it
is accessible after the appliance has
been installed in the countertop.
requirement be met. If there is any
doubt, have the electrical system of
the house checked by a qualified
electrician.
The manufacturer cannot be held
i responsible for damages caused by
the lack, or inadequacy, of an ............
Note to the installer
Please leave these instructions with the
consumer or the appliance.

Gas connection
This appliance must be installed
with its own shut off valve and the
included gas pressure regulator.
Both the valve and the regulator
must be easily accessible to the
consumer to turn on or shut off the
gas supply after the appliance is
installed.
This appliance and its individual
shut off valve must be disconnected
from the gas supply during any
pressure testing of the system
performed in excess of _' psi
(3.5 kPa). The machine must be
isolated from the gas supply line by
closing its individual manual shut off
valve at test pressures equal to or
less than _' psi (3.5 kPa).
Any pipe connections must be made
using a thread sealant approved for
gas connections. Failure to correctly
install these items could lead to a
......gas leak and subsequent explosion.
ANSI Z 21.1 for the USA
or
- the current Can/CGA
i Interim #58-M95
and _2Insta!lation Codes for gas
.........................................c a................
Make sure that the maximum gas
supply pressure, before the gas
pressure regulator, is never more than _/-
psi (3.5 kPa) for natural gas or LP gas.
The minimum supply pressure to get
the required gas input is
4"w.c. for natural gas
10"w.c. for LP gas.

Gas connection
Gas pressure regulator
A pressure regulator that is convertible
from natural to LP gas (Propane) or vice
versa is included with the appliance.
The adjusted pressure is for:
natural gas - 4" w.c.
LP gas - 10"w.c.
For convenience, an AGA or CGA
approved flexible stainless steel gas
hose (accordion type) may be used
between the gas connection and the
regulator. This will allow the appliance
to be lifted out of the countertop for
cleaning or servicing. Make sure that
any drawers, cabinet doors, etc., do not
rub on this gas hose.
'_ Regulator
As shown in the above diagram, the
included regulator must be used when
connecting the Miele cooktop to your
gas supply. This item has been
customized by Miele to meet a!l
applicable safety requirements. Make
sure the regulator is easily accessible
for adiustment after the appliance has
been installed.
so may cause a gas leak.
If there is any doubt concerning
installation contact the Miele Technical
Service Department at:
1-800-999-1360
[email protected]
!-800-565-6435
[email protected]
After connecting the appJJance check
aH fittings for gas leaks e.g. with
soapy water.
When installed properly, the flame will
be steady and quiet. It will also have a
sharp, blue inner core that will vary in
length proportional to the burner size.
Flame adiustment will not be necessary,
10