Miele TOUCHTRONIC T 1312 Parts list manual

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010706
Product Dimensions
Large Capacity Vented Dryers
Flat Controls
T1312
2"
23 1/2"
33 3/8" - 34 1/8"
22 1/2"
3 3/4" - 4 1/2"
V
Notes
• All installations must be done in accordance with local codes
• See "Cut-out Dimensions" sheet for undercounter or built-in space requirements
• Optional Easy Installation Kits utilize existing 208-240 Volt - 30 Amp line to
connect two Miele machines without rewiring .
E -
V-
5 foot - 208-240 Volt - 15 Amp 4-wire
(2 live / neutral / ground) molded plug
power supply connects upper right
rear (NEMA 14-30 Configuration).
Venting location may be adjusted to
lower right or left side or lower left
rear (see separate sheet).
Location Codes
E

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010706
Product Dimensions
Large Capacity Vented Dryer
Angled control
T1313
2"
23 1/2"
33 3/8" - 34 1/8"
22 1/2"
3 3/4" - 4 1/2"
21 1/2"
V
Notes
• All installations must be done in accordance with local codes
• See "Cut-out Dimensions" sheet for undercounter or built-in space requirements
• Optional Easy Installation Kits utilize existing 208-240 Volt - 30 Amp line to
connect two Miele machines without rewiring.
E -
V-
5 foot - 208-240 Volt - 15 Amp 4-wire
(2 live / neutral / ground) molded plug
power supply connects upper right
rear (NEMA 14-30 Configuration).
Venting location may be adjusted to
lower right or left side or lower left
rear (see separate sheet).
Location Codes
E

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010706
Product Dimensions
Large Capacity Condenser Dryers
Flat Controls
T1332C
2"
23 1/2"
33 3/8" - 34 1/8"
22 1/2"
3 3/4" - 4 1/2"
Notes
• All installations must be done in accordance with local codes
• See "Cut-out Dimensions" sheet for undercounter or built-in space requirements
• Optional Easy Installation Kits utilize existing 208-240 Volt - 30 Amp line to
connect two Miele machines without rewiring.
E -
D -
CD -
5 foot - 208-240 Volt - 15 Amp 4-wire
(2 live / neutral / ground) molded plug
power supply connects upper right
rear (NEMA 14-30 Configuration).
Drain location
Removable drawer if drain connection
is not utilized
Location Codes
CD
D
E

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010706
Product Dimensions
Large Capacity Condeser Dryer
Angled control
T1333C
2"
23 1/2"
33 3/8" - 34 1/8"
22 1/2"
3 3/4" - 4 1/2"
21 1/2"
Notes
• All installations must be done in accordance with local codes
• See "Cut-out Dimensions" sheet for undercounter or built-in space requirements
• Optional Easy Installation Kits utilize existing 208-240 Volt - 30 Amp line to
connect two Miele machines without rewiring.
E -
D -
CD -
5 foot - 208-240 Volt - 15 Amp 4-wire
(2 live / neutral / ground) molded plug
power supply connects upper right
rear (NEMA 14-30 Configuration).
Drain location
Removable drawer if drain connection
is not utilized
Location Codes
CD
D
E

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010706
Product Dimensions
Large Capacity Condenser Dryers
Flat Controls - Decor unit
T1339C
CD
2"
23 1/2"
33 3/8" - 34 1/8"
22 1/2"
5 7/8"
3 3/4" - 4 1/2"
1 1/2"
Notes
• All installations must be done in accordance with local codes
• See "Cut-out Dimensions" sheet for undercounter or built-in space requirements
• Optional Easy Installation Kits utilize existing 208-240 Volt - 30 Amp line to
connect two Miele machines without rewiring.
E -
D -
CD -
5 foot - 208-240 Volt - 15Amp 4-wire
(2 live / neutral / ground) molded plug
power supply connects upper right
rear (NEMA 14-30 Configuration).
Drain location
Removable drawer if drain connection
is not utilized
Location Codes
D
E

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010706
Cut-out Dimensions
Built-in Installations
Large Capacity Laundry Products
24"
See Notes
Water & Electrical
Connection
Location
C
32 3/8" - 35 1/4"
• Needed depth will vary by model number:
T1302,T1303,T1322C,T1323C: 24" minimum
T1329C: 25" minimum
• Typically requires removal of unit's lid. Out of box unit height dimension without
lid is 32 5/16" - 32 11/16".
Notes
Location Codes
C - Cutout for Electric and Vent or Drain
pass-through. Adjust according to duct
or drain location.

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010706
5 1/2"
4"
7 1/2"
Existing
208 / 240 Volt
30 Amp
Product Dimensions
Easy Installation Kits
057B / 060B
Notes
• Connect Washer and Dryer to Easy
Installation Kit
• All installations must be done in
accordance with local codes
• 057B Kit fitted with a NEMA10-30 Plug
• 060B Kit fitted with a NEMA14-30 Plug

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010706
Product Dimensions
Laundry Stand
WTS420 - White Only
26"
11"
Notes
• For use with both large and super
capacity washers or tumble dryers.
• All installations must be done in
accordnace with local codes
23 3/8"

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010706
Product Dimensions
Stacked Washer & Dryer
Example Combination
W1113 + T1313
2"
D
W
E
3 3/4" - 4 1/2"
23 1/2"
22 1/2"
66 3/8" - 67 1/8"
V
D -
E -
W -
V-
5 foot flexible drain hose connects
upper left rear.
208-240 Volt - 15 Amp 5 foot 4-wire
(2 live / neutral / ground) molded plug
power supply connects upper right
rear.
5 foot separate flexible hot and cold
water intake hoses connect upper left
rear.
Venting location may be adjusted to
lower right or left side or lower left rear
(see separate sheet).
Location Codes
Notes
• All installations must be done in accordance with local codes
• See "Cut-out Dimensions" sheet for undercounter or built-in space requirements
• Optional Easy Installation Kits utilize existing 208-240 Volt - 30 Amp line to
connect two Miele machines without rewiring.
• Remove transport struts in rear of washing machine before installation.
D
E

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010706
Panel Information
Integrated Laundry
T1339C Decor Unit
These units come equipped with a full size white front panel. These units are also designed to either accept a thin insert or
a custom front panel supplied by the custom cabinet maker.
Sizes are as follows: Version 1 - Thin insert
Width: 23 1/4" for all machines
Thickness: up to 1/8"
Height: 25" in all cases
With this version, a thin white frame will be exposed after
installation
Version 2 - Custom Front Panel
Width: 23 3/8" for all machines
Thickness: up to 3/4"
Height: Up to 25"
With this version, the existing front panel is removed and
replaced by the new custom panel
Miele
Decor
Laundry unit
Hinge Notches
In certain installations, notches will be required to
accomodate the hinges in the front panel.
Miele
Decor
Laundry
Control
Panel
To center lines
16 3/4"
Notch Pattern
For this installation, drill the following
pattern in the appropriate locations.
Note: To insure access to customer servicable features,
a minimum 4" toe kick above finished floor (AFF)
is required.
3 7/8"
C
C
C
1 1/8"
7/8"
1/4" Ø
1/4" Ø
1"
1"
Drill all holes
to a 5/8" depth
1 3/8" Ø

Vent Locations
Vented dryers
T1312, T1313
Rear ViewLeft Side View Right Side View
4 3/4" 3 7/8" 4 3/4"
3 1/2" - 4 1/4"
3 1/2" - 4 1/4"
3 1/2" - 4 1/4"
Vent Locations
Vent Duct Calculations
Maximum Duct Lengths
4" diameter 65 feet
4 3/16" diameter 98 feet
4 3/4" diameter 140 feet
5" diameter 196 feet
Type of Bend or duct Effective Radius Subtract
Flexible duct 90° 4 - 12 inches 1 3/4 feet
Flexible duct 90° 12 - 20 inches 1 1/4 feet
Flexible duct 45° 4 - 20 inches 1 1/4 feet
Smooth duct 90° or 45° 4 - 8 inches 1 1/4 feet
Elbow 90° Sharp bend 8 1/4 feet
Concertina bend 8 inch 2 3/4 feet
Segmented bend 8 inch 2 feet
Louvered wall or window vent (#03780400) 12 1/2 feet
Wall vent kit with flap (#00087184) 5 feet
Window vent kit with flap (#00087185) 5 feet
Exhaust connection - left 20 feet
Exhaust connection - right 33 feet
Flat duct (#01221330) 59 feet
DO NOT use vinyl ducting
with Miele appliances.
Corresponding Dryer Height with NO lid: 32 1/8" - 32 7/8"
Corresponding Dryer Height with lid: 33 3/8" - 34 1/8"

Vent Locations
Stacked Washer & Dryer
Example Combination
Rear ViewLeft Side View Right Side View
Vent Locations
Corresponding Total Height with lid: 66 3/8" - 67 1/8"
4 3/4"
36 3/8" - 37 1/8"
Stacking KitStacking Kit
36 3/8" - 37 1/8"
3 7/8" 4 3/4"
Stacking Kit
36 3/8" - 37 1/8"