Miele ELECTRIC BARBECUE CS 1322 User manual

Installation Instructions
CS 1322 en - CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.

Note to the installer:
Please leave this instruction book
with the consumer for the local
electrical inspector’s use.
The minimum distances given in
these Installation Instructions must
be observed in order to ensure safe
operation. Failure to do so increases
the risk of fire.
The cabinetry and venting hood
should be installed first to prevent
damage to the appliance.
~The countertop must be bonded
with heat resistant (212 °F/100 °C)
adhesive to prevent distortion or
dissolving.
The wall strips must be heat-resistant
as well.
~To eliminate the risk of burns or fire
by reaching over heated surfaces
cabinet storage space above the
appliance should be avoided. If cabinet
storage is necessary, the risk can be
reduced by installing a venting hood to
project horizontally a minimum of 5"
(127 mm) beyond the bottom of the
cabinets.
~This appliance must not be used in
a non-stationary location (e.g. on a
ship).
~You must ensure the power cable
for the appliance will not come under
any mechanical strain once installed
e.g., while the water is draining.
~Be sure that after installation the
power cord does not come into contact
with any parts of the appliance which
may become hot.
~The appliance must not be
permanently sealed into the countertop
when installed. The sealing strip under
the edge of the appliance provides a
sufficient seal for the countertop. See
"Sealing".
Keep this instruction book in a safe
place for reference and pass it on to
any future user.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS
22

Safety distances above the
appliance
The minimum safety distance given by
the hood manufacturer must be
maintained between the electric
barbecue and the hood above it. See
the installation instructions of the hood
for these safety measurements.
If the hood manufacturers instructions
are not available or if flammable objects
are installed over the electric barbecue
(e.g. cabinets, utensil rail, etc.), a
minimum safety distance of 30"
(760 mm) must be maintained.
If there is more than one appliance
beneath a hood (e.g. wok burner
and electric barbecue), and they
have different minimum safety
distances always observe the
greater distance.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS
23

Safety distances to the sides
of the appliance
The appliance should only be installed
as shown in the illustrations while
maintaining the required safety
distances shown. Do not install the
appliance between two tall cabinets,
this is a fire hazard.
A distance of at least 2" (50 mm) must
be kept between the countertop cut-out
and the rear wall because of the high
temperatures radiated.
The minimum distance required from
the countertop cut-out to a side wall or
tall cabinet right or left a:
2" (50 mm) for CS 1112
CS 1122
CS 1221
CS 1326
CS 1327
CS 1411
8" (200 mm) for CS 1312
CS 1322
10" (250 mm) for CS 1011
CS 1012
CS 1012-1
CS 1028
recommended
not recommended
not permitted
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS
24
2 " (50 mm)
(50mm)
1
2"

Safety distance from the wall covering
If a wall covering is installed, a minimum safety distance must be maintained
between the countertop cut-out and the covering, since high temperatures can
damage these materials.
If the covering is made of a combustible material (such as wood), the distance
between the countertop cut-out and the wall covering must be a minimum of
2" (50 mm).
For coverings made of non-combustible materials (such as metal, marble, granite
or ceramic tiles) the minimum safety distance ebetween the countertop cut-out
and the wall covering must be 2" (50 mm) minus the thickness of the covering.
For example: thickness of wall covering 9/16" (15 mm)
2" (50 mm) - 9/16" (15 mm) = minimum safety distance 1 3/8" (35 mm).
aWall frame
bWall covering
x= thickness of the wall covering
cCountertop
dCountertop cut-out
eMinimum safety distance
with flammable materials 2" (50 mm)
with non-flammable materials 2" (50 mm) minus x
Installation
25

Installation dimensions CS 1312
aSpring clips
bAppliance front
cInstallation height
dPower supply box with connection cable,L=783/4" (2000 mm)
eDrain valve
fRating label
Installation
26

Installation dimensions CS 1322
aSpring clips
bAppliance front
cInstallation height
dPower supply box with connection cable,L=783/4" (2000 mm)
eDrain valve
fRating label
Installation
27

Cut out
^Make the countertop cut-out for the
desired number of appliances.
Remember to maintain a minimum
safety distance from the back wall,
as well as from any tall unit or side
wall to the left or right of the
combiset.
See also the "IMPORTANT
INSTALLATION SAFETY
INSTRUCTIONS".
^Seal the cut surfaces with a suitable
sealant to avoid swelling caused by
moisture.
The materials used must be heat
resistant.
If, during installation, the seal
around the frame does not sit flush
with the countertop in the corners,
the corner radius, maximum 3/16"
(4 mm), can be carefully filed down
to fit.
Installation
28

Installation of multiple
appliances
When installing more than one combiset appliance, a support bar bmust be
installed between the appliances.
Countertop cut-out
two appliances
For the installation of two appliances
the width of the countertop cut-out D is
the sum of A and C.
A,Band C= appliance width
11 5/16", 15" or 22 11/16"
(288 mm, 380 mm or 576 mm)
minus 5/16" (8 mm) to allow for the
overhang
D= width of the countertop cut-out
Countertop cut-out
three appliances
For the installation of three appliances
the width of the countertop cut-out D is
the sum of A and B and C.
If more than three appliances are
being installed, you will need to add,
A, B or C for each additional
appliance.
Installation
29

Sample calculations for a countertop cut-out for three appliances
A
appliance width
minus 5/16"
(8 mm)
B
appliance width
C
appliance width
minus 5/16"
(8 mm)
D
Countertop
cut-out
11" (280 mm) 11 5/16" (288 mm) 11" (280 mm) 33 3/8" (848 mm)
11" (280 mm) 15" (380 mm) 14 5/8" (372 mm) 40 5/8" (1032 mm)
11" (280 mm) 22 11/16" (576 mm) 22 3/8" (568 mm) 56 1/16" (1424 mm)
14 5/8" (372 mm) 11 5/16" (288 mm) 11" (280 mm) 37" (940 mm)
14 5/8" (372 mm) 15" (380 mm) 14 5/8" (372 mm) 44 1/4" (1124 mm)
14 5/8" (372 mm) 22 11/16" (576 mm) 22 3/8' (568 mm) 59 11/16" (1516 mm)
22 3/8" (568 mm) 11 5/16" (288 mm) 11" (280 mm) 44 3/4" (1136 mm)
22 3/8" (568 mm) 15" (380 mm) 14 5/8" (372 mm) 52" (1320 mm)
22 3/8" (568 mm) - 22 3/8" (568 mm) 44 3/4" (1136 mm)
Installation
30

aSpring clips
bSupport bars
cSpace between support bar and countertop
dCover
The illustration represents the attachment of spring clips aand support bars b
for 3 appliances.
An additional support bar is required for each additional appliance. The position
for attachment of an additional support bar depends on the width of appliance B.
Installation
31

Attach the spring clips and
support bars
Wood or solid surface countertops
^Place the supplied spring clips a
and the support bars bat the
marked positions as shown above,
by laying them on the upper edge of
the cut-out and then securing them
with the 1/8" x 1" (3.5 x 25 mm) screws
(supplied).
Installation
32

Granite countertop
The screws are not needed for
granite countertops.
^Position and attach the spring clips
aand support bars bwith strong,
double-sided tape c.
^Coat the side and lower edges of the
spring clips between aand bwith
silicone.
^Fill the space ebetween the support
bars band the countertop with
silicone.
Installation
33

Installing the appliance(s)
^Feed the power cord down through
the cut-out.
^Place the front edge of the appliance
into the cut-out.
^With a hand on each side of the
appliance press down evenly on the
edges until it clicks into position.
When doing so make sure that the
appliance seal sits tightly on the
countertop to ensure it is sealed
correctly. This is important to ensure
an effective seal. Do not permanently
seal into the countertop.
^Push the installed appliance to the
side until the holes in the support bar
are visible.
^Insert the cover dinto the holes in
the support bar b.
^Place the front edge of the next
appliance into the cut-out.
^Connect the appliance(s) to the main
power supply (see "Electrical
connection").
^Turn the appliance(s) on and check
the function.
The appliance may be lifted out
using a special tool.
The appliance can also be pushed
up and out from underneath.
Note: push the rear out first.
Installation
34

After the appliance has been built in, the splash guard and protection plate(s)
should be fitted.
The protection plate(s) is only required if the barbecue grill is installed on its
own, i.e. detached from a multiple combiset configuration or another
appliance.
^Place the bracket aon the countertop against the back of the appliance.
^Align it so that it sits in the middle, and screw it to the countertop.
^Remove the paper from the adhesive tape underneath the protection plate(s)
bc.
^Position the protection plate(s) bc against the side(s) of the appliance and
press down.
^Attach the splash guard dto the bracket a.
The splash guard can be removed for cleaning.
Installation
35

Sealing
The appliance must not be permanently
sealed into the countertop when
installed. The sealing strip under the
edge of the appliance provides a
sufficient seal for the countertop.
If the appliance is sealed into
position, the countertop or appliance
could be damaged if it needs to be
removed for maintenance or service.
Tiled surfaces
The grouting aand shaded area under
the appliance frame must be flat and
even so that the frame will lie evenly
and the sealing strip under the edge of
the upper part of the appliance can
provide an adequate seal against the
countertop.
Installation
36

,CAUTION: Before installation or
servicing, disconnect the power
supply by either removing the fuse,
shutting off the main power or
manually "tripping" the circuit
breaker.
Installation work and repairs should
only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and service by unqualified
persons could be dangerous.
Before connecting the appliance to
the power supply, make sure that
the voltage and frequency listed on
the rating label correspond with the
household electrical supply. This
data must correspond to prevent
appliance damage. Consult an
electrician if in doubt.
Only operate the appliance after it
has been installed into the
countertop.
Installer:
Please leave these instructions with
the consumer.
Power supply
^Be sure your electrical supply
matches the rating label.
The rating label is located on the
underside of the appliance.
The combiset is equipped with a power
cord encasing 3 wires ready for
connection to a grounded power
supply.
They must be connected to a
dedicated line through the use of an
approved junction box.
Black : connect to L1 (hot)
Red: connect to L2 (hot)
Green: connect to GND (ground):
208 V, 60 Hz, 20 A fuse rating
240 V, 60 Hz, 15 A fuse rating
Be sure the power outlet is accessible
after installation.
For further information, see the wiring
diagram provided with the appliance.
,WARNING:
THIS APPLIANCE MUST BE
GROUNDED!
Electrical connection
37

Disposal of packing materials
The cardboard box and packing
materials are biodegradable and
recyclable. Please recycle.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!
Disposal of an old appliance
Old appliances contain materials that
can be recycled. Please contact your
local recycling authority about the
possibility of recycling these materials.
Before discarding an old appliance
disconnect it from the electrical supply
and cut off the power cord to prevent it
from becoming a hazard.
Help protect our environment
38

39

Alteration rights reserved / 3911
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
M.-Nr. 07 346 950 / 05