Miele DA 5000 D User manual

Operating and installation instructions
Cooker hood
DA 5000 D
To avoid the risk of accidents
or damage to this appliance
it is essential to read these
instructions before it is installed
and used for the first time. M.-Nr. 07 087 760
en-GB

Caring for the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mode of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
To switch the fan on s.............................................13
To select a power level .............................................13
Run-on option "5m15"..............................................14
To switch the fan off s.............................................14
Hob lighting n...................................................14
Feature lighting ...................................................15
Safety cut-out.....................................................15
Operating hours counter l..........................................15
Sensor control audible tones .........................................16
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Housing .........................................................17
Grease filters .....................................................18
Resetting the grease filter operating hours counter .....................19
Changing a halogen lamp ...........................................20
Changing a fluorescent tube .........................................21
Appliance dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Safety distance between hob and cooker hood........................22
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Installation instructions .............................................23
Assembly parts ...................................................23
Connection for air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Operation with Control module DSM 400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Connection to a window contact switch ..............................27
Potential free connection .........................................27
Connection to a light switch .......................................28
After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Contents
2

Disposal of the packing
material
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and can normally be
recycled.
Packaging e.g. cling film, polystyrene
and plastic wrappings must be kept out
of the reach of babies and young
children. Danger of suffocation!
Dispose of or recycle all packaging
materials safely as soon as possible.
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of your
old appliance with your household
waste.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person.
Caring for the environment
3

This appliance complies with all
relevant local and national safety
requirements. Inappropriate use
can, however, lead to personal injury
and damage to property.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time.
They contain important information
on the safety, installation, use and
maintenance of the appliance.
Keep these instructions in a safe
place and ensure that all users are
familiar with the contents. Pass them
on to any future owner of the
appliance.
Correct application
This appliance is intended for
domestic use only.
The manufacturer cannot be held liable
for damage caused by improper or
incorrect use of the appliance.
This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
have been given supervision or
instruction concerning use of the
appliance by a person responsible for
their safety.
Safety with children
This appliance is only intended for
use by adults who have read these
instructions.
This appliance is not a toy! To
avoid the risk of injury, keep
children well away, and do not allow
them to play with it or to use the
controls. They will not understand the
potential dangers posed by it. They
should be supervised whenever you
are working in the kitchen.
Older children may use the
appliance only when its operation
has been clearly explained to them and
they are able to use it safely,
recognising the dangers of misuse.
Please be aware that on
appliances with halogen lighting,
the lamps will get very hot during use
and remain hot for some time after
switching off. To safeguard against
burning, keep children well away from
the lamps at all times.
Warning and Safety instructions
4

Technical safety
Before installation, check the
cooker hood for visible signs of
damage. Under no circumstances
should you use a damaged appliance.
A damaged appliance is dangerous.
Before connecting the appliance to
the mains supply, make sure that
the voltage and frequency details given
on the data plate correspond with the
on-site electricity supply, otherwise the
appliance could be damaged. Consult
a qualified electrician if in any doubt.
The electrical safety of this
appliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system which complies with current
local and national safety regulations. It
is most important that this basic safety
requirement is present and tested
regularly, and where there is any doubt,
the household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).
For safety reasons, this appliance
may only be used when it has been
fully installed.
Only open the housing as
described in the instructions given
in the installation sheet and in the
Cleaning and care section of this
booklet. Under no circumstances
should any other parts of the housing
be opened.
Tampering with electrical connections
or components and mechanical parts is
highly dangerous to the user and can
cause operational faults.
Installation, maintenance and
repairs may only be carried out by
a Miele authorised person in
accordance with current national and
local safety regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
Faulty components must only be
replaced by genuine Miele original
parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
During installation, maintenance
and repair work, the appliance
must be disconnected from the mains
electricity supply. It is only completely
isolated from the electricity supply
when:
–it is switched off at the isolator,
–the screw-out fuse is removed (in
countries where this is applicable),
–the fuse from the fused spur
connection unit is withdrawn, or
–it is switched off at the mains fuse
box.
Warning and Safety instructions
5

Do not connect the appliance to
the mains electricity supply by a
multi-socket unit or an extension lead.
These do not guarantee the required
safety of the appliance (e.g. danger of
overheating).
This equipment may only be used
in mobile installations such as
ships, caravans, aircraft etc. if a risk
assessment of the installation has been
carried out by a suitably qualified
engineer.
In countries where there are areas
which may be subject to infestation
by cockroaches or other vermin, pay
particular attention to keeping the
appliance and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the guarantee.
Using at the same time as other
heating appliances that depend on
the air from the room
Warning - danger of toxic fumes
Great care should be taken when
using the cooker hood at the same
time and in the same room or area of
the house as another heating appliance
which depends on the air in the room.
Such appliances include gas, oil, wood
or coal-fired boilers and heaters,
continuous flow or other water heaters,
gas hobs, cookers or ovens which draw
air in from the room and duct exhaust
gases out through a chimney or
extraction ducting.
When used in extraction mode, the
appliance draws air in from the room in
which it is installed and from
neighbouring rooms.
If there is insufficient air, an
underpressure will occur. The heating
appliance may be starved of oxygen,
impairing combustion.
Harmful gases could be drawn out of
the chimney or extraction ducting back
into the room, with potentially fatal
consequences.
Warning and Safety instructions
6

In order to ensure safe operation, and
to prevent gases given off by the
heating appliances from being drawn
back into the room when the extractor
and the heater are in operation
simultaneously, an underpressure in the
room of 0.04 mbar (4 pa) is the
maximum permissible.
Ventilation can be maintained by air
inlets which cannot be blocked, in
windows, doors and outside wall vents,
or by other technical measures, such
as ensuring that the extractor can only
be switched on when the heating
appliance is switched off or vice versa.
A ventilation brick alone is not generally
sufficient to ensure safe ventilation.
,The overall ventilation condition
of the dwelling must be taken into
account. If in any doubt, the advice
of a competent builder or, for gas, a
"Corgi" installer, must be sought.
One of the following technical
measures may be necessary to ensure
safe operation.
–If the only way of ensuring adequate
ventilation is via an open window, a
window contact switch should be
fitted to ensure that the cooker hood
can only operate when the window is
opened sufficiently. A window
contact switch kit is available from
good builders' merchants.
Take care when ventilating the room
through an open window that
ventilation is not impaired by a
closed blind or curtain.
–The cooker hood can be set up to
automatically switch on an air intake
fan or open a motorised inlet flap
when it is switched on.
–The cooker hood can be set up to
automatically switch off a heating
appliance which also depends on
the air from the room when it is
switched on.
The Miele DSM 400 control module
offers the possibility of combining other
components with the cooker hood (see
"Operation with Control module DSM
400").
It is available to purchase as an
optional extra.
If in any doubt, the advice of a
competent builder or, for gas, a "Corgi"
installer, must be sought.
If the hood is being operated in
recirculation mode, the above
restrictions do not apply.
Warning and Safety instructions
7

Correct use
Never use an open flame beneath
the cooker hood. To avoid the
danger of fire, do not flambé or grill
over an open flame under the cooker
hood. When switched on, the cooker
hood could draw flames into the filter.
Fat particles drawn into the cooker
hood present a fire hazard.
When using the cooker hood over
a gas hob, ensure that any burners
in use are always covered by a pan.
Switch the cooking zone off when a pan
is removed, even for a short time.
Regulate the flame so that it does not
burn up the sides of the pan.
Do not allow the pans to overheat
excessively (e.g. when using a wok).
The cooker hood can become
damaged when exposed to excessive
heat.
Always switch the cooker hood on
when a cooking zone is in use,
otherwise condensation may collect in
the hood, which could cause corrosion.
When cooking with oil or fat, chip
pans and deep fat fryers etc, do
not leave the pans unattended. Never
leave an open grill unattended when
grilling. Overheated oil and fat can
ignite and could set the cooker hood on
fire.
Do not use the cooker hood without
the filters in place. This way you
will avoid the risk of grease and dirt
getting into the appliance and
hindering its smooth operation.
The filters should be regularly
cleaned or changed as
appropriate. Saturated filters are a fire
hazard. See "Cleaning and care".
Do not use a steam-cleaner to
clean this appliance. Pressurised
steam could reach the electrical
components and cause a short circuit.
Correct installation
The minimum safety distances
between the top of a cooker or hob
and the bottom of the cooker hood are
as follows, unless a greater distance is
specified by the manufacturer of your
cooking appliance:
–550 mm above electric hobs
and cookers,
–650 mm above gas hobs and
cookers,
–650 mm above an open grill or deep
fat fryer.
If more than one appliance is fitted
beneath the cooker hood and they have
different minimum safety distances to
the cooker hood, select the greater
distance.
Warning and Safety instructions
8

Safety regulations prohibit the
fitting of a cooker hood over solid
fuel stoves.
All ducting, pipework and fittings
must be of non-flammable material.
These can be obtained from the Miele
Spare Parts department or from
builders' merchants.
The appliance must not be
connected to a chimney or vent
flue which is in use. Neither should it be
connected to ducting which ventilates
rooms with fireplaces.
If exhaust air is to be extracted into
a chimney or ventilation duct no
longer used for other purposes, seek
professional advice.
Accessories
Accessory parts may only be fitted
when expressly approved by
Miele. If other parts are used,
guarantee, performance and product
liability claims may be invalidated.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
Warning and Safety instructions
9

Guide to the appliance
10

aCover plate
bTower
cCanopy
The canopy opens as soon as the fan is
switched on.
dFeature lighting
eControls
The symbols act as touch controls. To
select a function, touch the relevant
symbol. An audible tone sounds briefly
to confirm selection.
fHob lighting
gGrease filters
hTouch control for the
feature lighting
iTouch control for hob lighting
This control switches the lighting on
and off, and is also a dimmer switch.
jTouch control for switching the fan
on and off
kTouch controls to select the fan
power level
lTouch control for the run-on
option The fan can be set to switch
off automatically after either 5 or 15
minutes.
mTouch control for the grease filters
The touch control lights up when the
grease filters need to be cleaned.
The touch control is used to reset the
operating hours counter every time the
grease filters are cleaned (see
"Cleaning and care").
It can also be used to check and alter
the operating hours counter.
For information about using the
appliance, see "Operation".
Guide to the appliance
11

The cooker hood works with
. . . air extraction:
The air is drawn in and cleaned by the
grease filters and directed outside.
The cooker hood is fitted with a
non-return flap which is closed when
the cooker hood is switched off. No
exchange of room and outside air can
take place.
When the cooker hood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
Mode of operation
12

To switch the fan on
^Touch the ssensor.
The fan runs at power level 2.
The sand "2" sensors light up. The
canopy will open.
If the cooker hood has been
connected to a window contact
switch via the Miele DSM 400 control
module, then the fan cannot be
switched on if the window is shut.
The ssensor will flash.
To select a power level
Depending on the intensity of the
cooking vapours, levels 1 to 3 are
usually sufficient for normal cooking.
^Select the level you require by
touching the "1", "2" or "3" sensors.
Intensive setting
^For short periods of cooking food
with intensive vapours and a strong
aroma, e.g. when searing meat, you
may wish to select level 4, the
Intensive Setting.
Automatic switch-off of the Intensive
setting
You can set the Intensive setting so that
it always only runs for 10 minutes
before reverting automatically to level 3.
^To set this option, both the fan and
the hob lighting must be switched off.
^Touch the "5m15" sensor for approx.
10 seconds until the "1" sensor lights
up.
^Touch in turn
–the nsensor,
–the "1" sensor and
–the nsensor again.
The sensors for fan power levels 1 and
4 will flash if the automatic switch-off for
the Intensive setting is not activated.
^Touch the "4" sensor to activate auto-
matic switch-off.
The "1" and "4" sensors will now light
up constantly.
Touch the "1" sensor to deactivate the
automatic switch-off function.
^Touch the "5m15" sensor to confirm
your selection.
If you do not confirm your selection
within 4 minutes, the cooker hood will
automatically revert to the original
setting.
Operation
13

Run-on option "5 15"
It is advisable to leave the fan running
for a few minutes after cooking has
finished to neutralise any lingering
odours in the air.
The fan can be set to switch off
automatically after either 5 or 15
minutes.
^After cooking has finished, press the
run-on option control "5m15" whilst
the fan is still running.
–Press once = The fan will switch off
after 5 minutes (the "5" lights up).
–Press twice = The fan will switch off
after 15 minutes (the "15" lights up).
To switch off the run-on option, touch
the run-on option sensor again. The
appliance will then not switch off
automatically.
To switch the fan off
^Touch the ssensor to switch the fan
off.
The canopy will close.
^If the canopy needs to be kept open
after it has been switched off (e.g. for
cleaning), touch the current fan level
sensor for approx. 5 seconds whilst
the fan is running, until the fan
switches off. The canopy will remain
open.
To switch the fan on again, touch any
of the fan level sensors.
Hob lighting
The hob lighting can be switched on
and off independently of the fan.
To switch the hob lighting on
^Touch the nsensor briefly.
The lighting will switch on at maximum
brightness.
To dim the hob lighting
The brightness of the lighting can be
adjusted.
^With the lighting switched on, touch
and hold the nsensor.
The brightness will gradually dim until
you release the sensor.
^To increase the brightness, touch the
sensor again to the level required,
then release it.
If you keep your finger on the sensor,
the light will continually change
between bright and dim.
To switch the hob lighting off
^Touch the nsensor briefly.
Operation
14

Feature lighting
The feature lighting can be switched on
and off by touching the" "sensor.
Safety cut-out
Should the cooker hood be left on, the
fan will switch off automatically after 10
hours. The lighting will remain on.
^Touching the ssensor will switch the
fan back on again.
Operating hours counter
The number of hours the appliance has
been in operation is stored in memory.
The operating hours counter tells you
when the grease filters need to be
cleaned.
After 30 hours of operation (or another
time if the operating hours counter has
been altered), the lsensor will light
up. The grease filters must then be
cleaned.
Afterwards, the operating hours counter
will need to be reset (see "Cleaning and
care").
Reading the grease filter operating
hours counter
To check the percentage of time set
already used:
^Touch the ssensor to switch the fan
on.
^Touch and hold the lsensor.
One or more of the "1" to "4" sensors will
flash.
The number of flashing sensors
indicates the percentage of the
operating time which has already been
used up.
Sensor "1" = 25 %
Sensors "1" and "2" = 50 %
Sensors "1" to "3" = 75 %
Sensors "1" to "4" = 100 %
The number of operating hours used
remains in the memory, even when the
appliance is switched off or there is a
power cut.
Operation
15

Altering the grease filter operating
hours counter
You can set the operating hours
counter to suit the type of cooking you
do.
The operating hours counter is set at
the factory for 30 hours.
Select a shorter time of 20 hours if you
fry a lot.
If you only cook occasionally, we still
recommend 20 hours, because grease
which has built up gradually over a long
period of time will harden on the grease
filters and make cleaning more difficult.
If you use very little fat for cooking,
select a longer time.
To alter the operating time:
^Touch the ssensor to switch the fan
off.
^Touch the "5m15" and lsensors at
the same time.
The land one of the "1" to "4" sensors
will flash.
The "1" to "4" sensors indicate the time
which has been set:
Sensor "1" = 20 hours
Sensor "2" = 30 hours
Sensor "3" = 40 hours
Sensor "4" = 50 hours
^Touch the "1" sensor to select a
shorter time and the "4" sensor to
select a longer time, until the time
required has been set.
^Confirm your selection by touching
the lsensor.
All the lamps will go out.
If you do not confirm your selection
within 4 minutes, the cooker hood will
automatically revert to the original
setting.
Sensor control audible tones
When selecting a function with the
sensors, an audible tone will sound
briefly to confirm.
The audible tone can be deactivated.
^Touch the ssensor to switch the fan
off.
^Touch the "4" and lsensors at the
same time for approx. 5 seconds until
an audible tone sounds briefly. The
audible tone is now switched off for
all functions.
^To reactivate the audible tone, repeat
the above process.
After the cooker hood has been
disconnected from the mains electricity
supply or after a power cut, the audible
tone is activated regardless of the last
setting.
Operation
16

Housing
General notes
The surfaces are susceptible to
scratches and abrasions. Please
observe the following cleaning
instructions.
^All external surfaces and controls can
be cleaned using an E-cloth
(available from the Miele Spare Parts
Department or via the Internet on
www.miele.co.uk), or with warm water
and a little washing-up liquid applied
with a well wrung-out soft sponge or
cloth.
Only use a damp cloth as water
could get into the appliance and
cause damage.
^Wipe the surfaces dry using a soft
cloth.
Do not use:
–cleaning agents containing soda,
acids, chlorides or solvents,
–abrasive cleaning agents, e.g.
powder cleaners or cream cleaners,
and abrasive sponges, e.g. pot
scourers or sponges which have
been previously used with abrasive
cleaning agents. These will damage
the surface material.
Important for appliances with
stainless steel surfaces
^Stainless steel surfaces can be
cleaned using the Miele E-Cloth or
with a suitable, non-abrasive,
proprietary cleaning agent, following
the manufacturer's instructions on the
packaging.
^To help prevent re-soiling, a
proprietary conditioning agent for
stainless steel (available from the
Miele Spare Parts Department or via
the internet on www.miele.co.uk) can
also be used.
Important for appliances with glass
surfaces
^Glass surfaces can be cleaned using
a proprietary non-abrasive cleaning
agent designed specifically for use
on glass.
Do not use:
–sharp metal tools,
–oven sprays.
Cleaning and care
17

Grease filters
The re-usable metal grease filters in the
appliance remove solid particles
(grease, dust, etc.) from the kitchen
vapours, preventing soiling of the
cooker hood.
The grease filters should be cleaned
regularly (at least every 3-4 weeks) to
avoid a build-up of fat, but always clean
immediately if the lsensor lights up.
An oversaturated filter is a fire
hazard.
To remove the grease filters, the
canopy needs to be open.
^Touch the ssensor to switch the fan
on.
The fan will start running at power level
2, and the canopy will open.
^Touch the "2" sensor for approx. 5
seconds, until the fan switches off.
The canopy will remain open.
To avoid damaging the filters or the
hob below, make sure you hold the
filters securely at all times when
handling them.
^Holding the grease filter by the
handle, push upwards out of the
lower groove, hinge it forwards and
lift it down and out.
Cleaning the grease filters by hand
^Clean the filters with a soft nylon
brush in a mild solution of hot water
and a little washing-up liquid.
Do not use "neat" washing up liquid.
Do not use:
–cleaning agents containing
descaling agents,
–alkaline cleaning agents (with a pH
value higher than 7), such as powder
cleaners, cream cleaners or abrasive
all-purpose cleaning agents,
–oven sprays.
Cleaning and care
18

Cleaning the grease filters in the
dishwasher
^Place the filters with the short side
upright in the lower basket, and wash
on a 65°C programme using a mild
dishwasher detergent, ensuring the
spray arm is not obstructed.
Avoid alkaline dishwasher detergents
(with a pH value higher than 7).
Depending on the cleaning agent
used, cleaning the filters in a
dishwasher can cause permanent
discolouration to the surface.
However, this will not affect the
functioning of the filters in any way.
^After cleaning, leave the filters to dry
on an absorbent surface before
replacing them.
^When removing the filters for
cleaning, also clean off any residues
of oil or fat from the now accessible
housing to prevent the risk of these
catching fire.
^When the cooker hood is operating,
grease residues are deposited in the
grooves on either side of the canopy.
Clean these grooves and the grease
filter holders every time the grease
filters are removed.
^Replace the grease filters.
^Then touch any of the "1" to "4"
sensors. The fan will then switch
back on.
Resetting the grease filter operating
hours counter
After cleaning, the operating hours
counter needs to be reset.
^Touch the ssensor to switch the fan
on.
^Touch the lsensor for approx.
3 seconds until only the "1" sensor is
flashing.
The lsensor light will go out.
If the grease filters are cleaned before
the operating hours counter has
reached its maximum,
^touch the lsensor for approx.
6 seconds until only the "1" sensor is
flashing.
Cleaning and care
19

Changing a halogen lamp
To change the lamps, the canopy
needs to be open.
^Touch the ssensor.
The fan will start running at power level
2, and the canopy will open.
^Touch the "2" sensor for approx. 5
seconds, until the fan switches off.
The canopy will remain open.
^Before any cleaning or maintenance
work, disconnect the cooker hood
from the mains supply. Ensure that:
–it is switched off at the isolator, or
–the screw-out fuse is removed (in
countries where this is applicable), or
–the fuse from the fused spur
connection unit is withdrawn, or
–it is switched off at the mains fuse
box.
^Remove the grease filters.
,Exercise caution when changing
halogen lamps. They get very hot
during use, and remain hot for some
time after being switched off: danger
of burning.
Wait until the lamps have cooled
down before changing them.
^Press the lighting unit down slightly
through the hole above the lamp, as
shown.
^Turn the halogen lamp anti-clockwise
out of its socket.
^Replace it with a new halogen lamp
(specification: GU/GZ 10, 230 V, 50
W, 50°). Screw the lamp into the
socket and push it upwards.
We recommend only using lamps of the
same specification and also made by
the same manufacturer as the ones
being replaced.
^Replace the grease filters.
^Reconnect the cooker hood to the
mains supply.
The canopy will close.
Cleaning and care
20