Miele KMR1124 G User manual

Installation Instructions
KMR1124 G, KMR1134 G, KMR1135 G
KMR1136 G, KMR1354 G, KMR1355 G
KMR1356 G en - CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.

Notes on installation
38
Distance to the range hood
The minimum clearance between the
appliance and a range hood above will
be listed by the hood manufacturer.
If there is more than one appliance in‐
stalled below the range hood, each with
a different safety clearance, the largest
clearance must be used.

Notes on installation
39
Weights
The net weight of the rangetop with accessories is as follows:
Model Width Net weight incl. acces‐
sories:
KMR 1124 G/LP 30" approx. 100 lbs / 45 kg
KMR 1134 G/LP
KMR 1135 G/LP
KMR 1136 G/LP 36" approx.120 lbs / 55 kg
approx. 130 lbs / 60 kg
approx. 151 lbs / 68.5 kg
KMR 1354 G/LP
KMR 1355 G/LP
KMR 1356 G/LP 48" approx. 150 lbs / 68 kg
approx. 160 lbs / 73 kg
approx. 170 lbs / 78 kg

Dimensional drawings
40
In case of the presence of combustible material an additional minimum clear‐
ance of 6“ (each side) is necessary. Ensure local codes are observed.
Position Dimension Description
13" (330 mm) Maximum depth of top cabinet
18" (457 mm) Minimum distance to bottom edge
of top cabinet
7¹/₂" (190.5 mm) Distance top edge of worktop to
top edge of platform
10" (254 mm) Minimum distance to flammable
surfaces
Platform1)
1) The Platform must be ³/₄" (19.05 mm) thick.
It must include a cut-out of 5¹/₈" x 3¹/₈" (130 mm x 80 mm) (gas connection) at the rear right
and a cut-out of 4³/₄" x 1⁹/₁₆" (120 mm x 40 mm) (elctrical connection) at the rear left.

Dimensional drawings
41
KMR 1124
Position Dimension Description
min. 30"
(762 mm) Width of cabinet opening
6“ + + 6"
(150 mm + + 150 mm)
In case of the presence of com‐
bustible material an additional min‐
imum clearance of 6“ (each side) is
necessary. Ensure local codes are
observed.
37" (940 mm) Minimum distance between the top
of the cooking area and the bottom
of an unprotected combustible sur‐
face.
30" (762 mm) Minimum distance between the top
of the cooking area and the bottom
of the Miele Range Hood (DAR
model with DRxB XL Blower).
For all other Hoods, please consult with manufacturer's instructions
for required distances.

Dimensional drawings
42
KMR 1134
Position Dimension Description
min. 36"
(914 mm) Width of cabinet opening.
6“ + + 6"
(150 mm + + 150 mm)
In case of the presence of com‐
bustible material an additional min‐
imum clearance of 6“ (each side) is
necessary. Ensure local codes are
observed.
37" (940 mm) Minimum distance between the top
of the cooking area and the bottom
of an unprotected combustible sur‐
face.
36" (914 mm) Minimum distance between the top
of the cooking area and the bottom
of the Miele Range Hood (DAR
model with DRxB XL Blower).
30" (762 mm) Minimum distance between the top
of the cooking area and the bottom
of the Miele Range Hood (DAR
model with DRxB XXL Blower).
For all other Hoods, please consult with manufacturer's instructions
for required distances.

Dimensional drawings
43
KMR 1135 / KMR 1136
Position Dimension Description
min. 36"
(914 mm) Width of cabinet opening
6“ + + 6"
(150 mm + + 150 mm)
In case of the presence of com‐
bustible material an additional min‐
imum clearance of 6“ (each side) is
necessary. Ensure local codes are
observed.
37" (940 mm) Minimum distance between the top
of the cooking area and the bottom
of an unprotected combustible sur‐
face.
30" (762 mm) Minimum distance between the top
of the cooking area and the bottom
of the Miele Range Hood (DAR
model with DRxB XL or DRxB XXL
Blower).
For all other Hoods, please consult with manufacturer's instructions
for required distances.

Dimensional drawings
44
KMR 1354 / KMR 1355 / KMR 1356
Position Dimension Description
min. 48"
(1219 mm) Width of cabinet opening
6“ + + 6"
(150 mm + + 150 mm)
In case of the presence of com‐
bustible material an additional min‐
imum clearance of 6“ (each side) is
necessary. Ensure local codes are
observed.
37" (940 mm) Minimum distance between the top
of the cooking area and the bottom
of an unprotected combustible sur‐
face.
36" (914 mm) Minimum distance between the top
of the cooking area and the bottom
of the Miele Range Hood (DAR
model with DRxB XXL Blower).
For all other Hoods, please consult with manufacturer's instructions
for required distances.
12" (305 mm) minimum distance is necessary from back of range to combustible rear wall
above countertop.

Dimensional drawings
45
aSide view
bFront views
cRear view
dElectrical connection
eGas connection

Electrical connection
46
ATTENTION:
During installation, maintenance and
repair work, the rangetop must be
disconnected from the electricity
supply. It is only completely isolated
from the electricity supply if the plug
fuses have been fully unscrewed
(where applicable), the main circuit
breaker has been tripped or the
power cable has been unplugged
from the wall outlet.
Do not cut off the plug on the power
cord. If the plug does not fit in the
outlet, have an electrician install an
appropriate outlet.
The socket must be easily accessi‐
ble after the rangetop has been in‐
stalled.
Installation, repair and maintenance
work should only be performed by a
Miele authorized service technician.
Work by unqualified persons can
cause considerable danger to users.
Miele cannot be held liable for any
damage arising as a result of such
work.
To avoid damaging the rangetop,
make sure that the information (volt‐
age and frequency) on the data plate
correspond to the building's power
supply before connecting the appli‐
ance.
When in doubt, consult a qualified
electrician.
The power cable plug must be in‐
serted into a suitable outlet that has
been installed and grounded in com‐
pliance with all applicable local regu‐
lations.
WARNING: THIS APPLIANCE MUST
BE GROUNDED
Installer: Please pass these instruc‐
tions on to the customer.
Electrical connection
The rangetop is equipped with an ap‐
prox. 4 ft. long power cord with a plug
for connection to the electrical supply
with:
– 120 V, 15 A, 60 Hz
SAVE THESE INSTRUCTIONS FOR
THE ELECTRICAL INSPECTOR'S
USE.
This appliance must be grounded in
compliance with all applicable local
and national regulations.
Installation, repair and maintenance
work should only be performed by a
Miele authorized service technician
in compliance with local regulations
and the ANSI National Electrical
Code / NFPA 70 in the United States
or the Canadian Electrical Code, Part
I in Canada (CSA standard C22.1).

Gas connection
47
Connection to the gas supply
and any switchover to a different gas
type may only be performed by a du‐
ly authorized gas company techni‐
cian. This technician is responsible
for proper function at the installation
site.
In Massachusetts installation must
be performed by a licensed
plumber/gas fitter.
The rangetop must be connected
with its own shut-off valve.
The shut-off valve must be accessi‐
ble and visible, after the opening of a
cabinet door, if necessary.
The gas connection of the rangetop
can be to natural gas or liquid gas
(propane) according to the model.
Ask your gas company what kind of
gas is used and compare it with the
specifications on the data plate.
The rangetop is not connected to an
exhaust vent.
During the setup and connection of
the rangetop, observe the applicable
installation conditions, especially
suitable ventilation measures.
The gas connections must be ar‐
ranged in such a way that they are
not heated and damaged by the op‐
eration of the range.
In particular, make sure that the gas
hose lines and connection fittings on
the rangetop do not come into con‐
tact with hot exhaust gases.
The gas hose and power cord could
be damaged by hot spots on the
rangetop.
Make sure that the gas hose and
power cord do not come into con‐
tact with hot spots on the rangetop.
Flexible connection lines can be
damaged by incorrect routing.
Attach flexible connecting lines in
such a way so that they do not come
into contact with any moving kitchen
parts (e.g., a drawer) and are not ex‐
posed to mechanical stress.
The rangetop and the shut-off valve
must be disconnected from the gas
supply during gas pressure tests.
Disconnect the rangetop and the
shut-off valve from the gas supply
before performing a gas pressure
test at a pressure of more than
1/2 psi (3.5 kPA). Close the shut-off
valve of the gas supply before per‐
forming a gas pressure test at a
pressure of less than or equal to
1/2 psi (3.5 kPA).
Incorrectly sealed gas lines can lead
to a gas leak and thus to an explo‐
sion.
Seal all gas lines with a suitable
thread sealant.
Seal tightness tests on the rangetop
must be performed according to
manufacturer specifications.

Gas connection
48
The gas connection must be made in
accordance with local codes or, in
the absence of local codes, with:
the National Fuel Gas Code,
ANSI Z223.1 / NFPA 54 for the USA
or the current Can / CGA B 149.1
and .2 Installation Codes for gas
burning appliances for Canada.
The gas pressure may not under‐
shoot or exceed certain values.
Make sure that the maximum gas
pressure upstream of the gas pres‐
sure controller does not amount to
more than 1/2 psi (3.5 kPA) for natu‐
ral and propane gas.
Make sure that the minimum gas
pressure amounts to a 6" water head
in the case of natural gas and a 11"
water head in the case of propane
gas.
The gas connection of the rangetop is
designed for natural gas or liquid gas
(propane) according to the ordered
model.
If the rangetop is not equipped with the
correct connection for the gas type in
your household, contact your Miele
dealer.
Miele gas rangetops will function up to
an altitude of 10,000' (3000 m). If the in‐
stallation exceeds these elevations, the
appliance must be converted. Contact
your Miele dealer.

Burner ratings
49
KMR 1124 G/LP
Gas type Btu/hr kW
Max Max
Simmer burner Natural gas 12,500 3.70
Propane gas 12,500 3.70
Power burners Natural gas 19,500 5.70
Propane gas 19,500 5.70
Total output Natural gas 71,000 20.80
Propane gas 71,000 20.80
KMR 1134 G/LP
Gas type Btu/hr kW
Max Max
Simmer burner Natural gas 12,500 3.70
Propane gas 12,500 3.70
Power burners Natural gas 19,500 5.70
Propane gas 19,500 5.70
Total output Natural gas 110,000 32.20
Propane gas 110,000 32.20

Burner ratings
50
KMR 1135 G/LP
Gas type Btu/hr kW
Max Max
Simmer burner Natural gas 12,500 3.70
Propane gas 12,500 3.70
Power burners Natural gas 19,500 5.70
Propane gas 19,500 5.70
Grill Natural gas 19,000 5.50
Propane gas 15,500 4.50
Total output Natural gas 90,000 26.30
Propane gas 86,500 25.30
KMR 1136 G/LP
Gas type Btu/hr kW
Max Max
Simmer burner Natural gas 12,500 3.70
Propane gas 12,500 3.70
Power burners Natural gas 19,500 5.70
Propane gas 19,500 5.70
Griddle Natural gas 13,000 3.80
Propane gas 14,300 4.20
Total output Natural gas 84,000 24.60
Propane gas 85,300 25.00

Burner ratings
51
KMR 1354 G/LP
Gas type Btu/hr kW
Max Max
Simmer burners Natural gas 12,500 3.70
Propane gas 12,500 3.70
Power burners Natural gas 19,500 5.70
Propane gas 19,500 5.70
Total output Natural gas 142,000 41.60
Propane gas 142,000 41.60
KMR 1355 G/LP
Gas type Btu/hr kW
Max Max
Simmer burners Natural gas 12,500 3.70
Propane gas 12,500 3.70
Power burners Natural gas 19,500 5.70
Propane gas 19,500 5.70
Grill Natural gas 19,000 5.50
Propane gas 15,500 4.50
Total output Natural gas 122,000 35.70
Propane gas 118,500 34.70

Burner ratings
52
KMR 1356 G/LP
Gas type Btu/hr kW
Max Max
Simmer burners Natural gas 12,500 3.70
Propane gas 12,500 3.70
Power burners Natural gas 19,500 5.70
Propane gas 19,500 5.70
Griddle Natural gas 13,000 3.80
Propane gas 14,300 4.20
Total output Natural gas 116,000 34.00
Propane gas 117,300 34.40

Miele service, data plate, warranty
53
After sales service
In the event of a fault which you cannot easily correct yourself, please contact:
– your Miele dealer, or
– the Miele Technical Service Department.
See back cover for contact details.
Please quote the model and serial number of your appliance when contacting
Miele.
Data plate
Adhere the extra data plate supplied with the appliance here. Ensure that the mod‐
el number is the same as the one on the back of these operating instructions.
Warranty
For further information, please refer to your warranty booklet.

Caring for the environment
54
Disposal of the packing mate‐
rial
The cardboard box and packing materi‐
als protect the appliance during ship‐
ping. They have been designed to be
biodegradable and recyclable.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children. Dan‐
ger of suffocation!
Disposal of your old appliance
Old electrical and electronic appliances
often still contain valuable materials.
However, they also contain harmful
substances that were essential for the
proper functioning and safe use of the
equipment. Handling these materials
improperly or disposing of them in your
household waste can be harmful to
your health and the environment.
Therefore, please do not dispose of
your old appliance with regular house‐
hold waste.
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
Please be sure that your old appliance
does not pose a danger to children
while being stored for disposal.

9 Independence Way
Princeton, NJ 08540
Phone:
Fax:
www.mieleusa.com
U.S.A.
Miele, Inc.
National Headquarters
Please have the model and serial number
of your appliance available before
contacting Technical Service.
Canada
Importer
Miele Limited
Headquarters and Miele Centre
800-843-7231
609-419-9898
609-419-4298
Technical Service & Support
Nationwide
Phone:
Fax:
[email protected]
161 Four Valley Drive
Vaughan, ON L4K 4V8
www.miele.ca
800-999-1360
888-586-8056
Customer Care Centre
Phone:
[email protected]
800-565-6435
905-532-2272
Germany
Manufacturer
Miele & Cie. KG
Carl-Miele-Straße 29
33332 Gütersloh
55

M.-Nr. 10 004 330 / 02en-US
KMR 1124 / KM 1134 / KMR 1135 / KMR 1136 / KM 1354 / KMR
1355 / KMR 1356
