Miele PW 5105 EL User manual

Installation Plan
Washer-extractor
PW 5105 EL (Electrically Heated)
en - US
22.15 M.-Nr. 10 182 730 / 01

It is essential to read the operating and installation instructions before
installing, commissioning or using the machine.
This avoids the risk of accidents or damage.
All rights reserved
2

Technical datasheet
Washer-extractor:
Heating:
PW 5105 AV (Dump valve)
Electric (EL)
Legend: Abbreviations in bold type:
Connection required en - US
Abbreviations in circle with dashes:
Connection optional or required depending on model version
Optional extras:
UM Miele base
UO 5010 (UO = open base)
Height
12''
305 mm
Width
27''
684 mm
Depth
31''
787 mm
UG 5010 (UG = closed base)
Height
12''
305 mm
Width
27 1/4''
692 mm
Depth
31''
788 mm
BS Concrete base Quality and density of concrete must comply with load.
Concrete base must be firmly secured to floor!
Recommended height
11 13/16''
300 mm
Minimum height
2 3/4''
70 mm
Recommended width
≥27 9/16''
≥700 mm
Recommended depth
≥31 1/2''
≥800 mm
Dispensing
pump Pump installation may only be performed by Miele Service.
External dispensing pumps (2 or 4 head pump):
Voltage (external power supply required)
120V
Fusing
15A
Supplied with supply cable and plug
NEMA 5-15
Machine connections:
Electrical
connection
(convertible)
2 AC 220 - 240V
60 Hz
4.4 - 5.2 kW
2x 30 A
2000 mm NEMA
L6-30P
Electrical connection must comply with national regulations.
Connection using multi-pole wall lockable socket in compli-ance with IEC/EN 60309 and IEC/EN 60947 is
recommended in order to simplify electrical tests. Ifmachines are hard-wired, a multi-pole mains switch must be
provided on site. Switches with a contact gap of more than 3 mm can be used. These include switches, fuses and
contactors (IEC/EN 60947).Awall socket or mains isolator must be easily accessible after installation.
Reinstallation of the supply point, changes to the equipment or checks on the protective conductor, including
determination of correct fuse rating, should only be performed by a properly trained electrician.
If necessary, equipotential bonding with good galvanic contact must be provided in accordance with all
appropriate national and local regulations.
Technical datasheet: PW5105 EL AV (Dump valve)
Date: 01.2015 Page: 11
Convertible to
Frequency
Rated load
Fuse rating
Length of supply lead
Supplied with plug
2 AC 208V
60 Hz
4.0 kW
2x 30 A
2000 mm NEMA
L6-30P
6.5'
Standard voltage
Frequency
Rated load
Fuse rating
Length of supply lead
Supplied with plug
6.5'

Cold water
(Soft water)
Min. flow pressure
Max. pressure
Max. throughput
On-site connection thread
14.5 psi
145 psi
2.9 gal/min
3/4"garden hose
thread, male
61''
approx.
18.5 gal/h
100 kPa
1000 kPa
11 l/min
3/4"garden hose
thread, male
1550 mm
approx.
70 l/h
Length of connection hose (supplied: 1 connection hose)
Hourly water demand (average for 60°Cprogram) for
standard connection (with warm and cold water)
If warm water supply is not available add warm water
demand to cold water demand.
Warm water
(Soft water)
Max. temperature
158°F
70°C
Min. flow pressure
14.5 psi
100 kPa
Max. pressure
145 psi
1000 kPa
Max. throughput
2.9 gal/min
11 l/min
On-site connection thread
3/4"garden hose
thread, male
3/4"garden hose
thread, male
Length of connection hose
(supplied: 1 connection hose)
61''
1550 mm
Hourly water demand (average for 60°C program)
approx.
18.5 gal/h
approx.
70 l/h
If reprogrammed by Miele Service, the Machine can also be
connected to a hot water supply line with a temperature of
70°C to max. 85°C. This requires a separate inlet hose.
This additional inlet hose is available from Miele Spares.
If warm water isnot available, connect warm water hoseto
cold water valve!
Drain: Dump
valve
Max. temperature
158°F
70°C
Machine-side drain connection (ext. diameter)
2 15/16''
75 [DN 70] mm
On-site drain (int. diameter)
2 15/16''
75 [DN 70] mm
Max. transient throughput
16.4 gal/min
62 l/min
Vented drainage required. If ventilation is insufficient, fit Miele
kit, Mat. no. 05238090.
Drain manifolds serving several machines must be of
sufficient cross-section.
Fittings for
base/floor
installation
Miele base UG/UO 5010
4 × metal angled brackets
(to secure machine to base )
4 × screws DIN 571 (Ø × length)
5/16'' x2 9/16'' 8 mm x65 mm
4 × rawl plugs (Ø × length)
1/2'' x 2 3/8'' 12 mm x60 mm
Machine must be bolted to the base and floor!
Fixing materials for a floating screed floor are to be provided
on site.
Installation on floor or concrete base
2 × clamps
2 × screws DIN 571 (Ø × length)
2 × rawl plugs (Ø × length)
1/2'' x 2'' 6 mm x50 mm
5/16'' x1 9/16'' 8 mm x40 mm
Machine must be bolted to the base or floor. Fittings are
supplied with machine
Fixing materials for a floating screed floor are to be provided
on site.
AV
Technical datasheet: PW5105 EL AV (Dump valve)
Date: 01.2015 Page: 12

Machine data
Unit width
27 9/16''
700 mm
Machine depth
32 9/16''
827 mm
Unit height
40 3/16''
1020 mm
Casing width
31 3/16''
792 mm
Casing depth
31 1/8''
790 mm
Minimum width of delivery access to installation site
28 3/8''
720 mm
Recommended rear wall gap (measured to front of machine) 47 1/4''
1200 mm
Minimum rear wall gap (to front of machine)
Recommended rear wall gap ensures sufficient space for
maintenance and servicing.
39 3/8''
1000 mm
Net weight
327 lbs
148 kg
Dynamic floor load, max.
2750 N
2750 N
Static floor load, max.
1960 N
1960 N
Dynamic load, max.
790 N
790 N
Drum frequency, max.
18 Hz
18 Hz
Average heat dissipation
(dependent on ambient room temperature and program
selected)
2630 BTU/hr
0.77kWh
Sound pressure (re 20 mPA),
workplace-related (at distance of 1 m and height of 1.6 m)
<70 dB (A)
<70 dB (A)
Installation should only be carried out by authorized installers in accordance with valid regulations!
Follow installation instructions when installing machine! All rights reserved!
Technical datasheet: PW5105 EL AV (Dump valve)
Date: 01.2015 Page: 13