mikroElektronika mikromedia for PIC32 User manual

Compact development system rich with on-board peripherals for all-round
multimedia development on PIC32MX460F512L device.
for PIC32®
mikromedia™
PIC32

I want to express my thanks to you for being interested in our products and for having
condence in Mikroelektronika.
The primary aim of our company is to design and produce high quality electronic products
and to constantly improve the performance thereof in order to better suit your needs.
The PIC32®and Windows®logos and product names are trademarks of Microchip Technology®and Microsoft®in the U.S.A. and other countries.
TO OUR VALUED CUSTOMERS
Nebojsa Matic
General Manager

Page 3
Introduction to mikromedia for PIC32®4
Package Contains 5
Key Features 6
System Specication 7
1. Power supply 8
USB power supply 8
Battery power supply 8
2. PIC32MX460F512L microcontroller 10
Key microcontroller features 10
3. Programming the microcontroller 11
Programming with mikroBootloader 12
step 1 – Connecting mikromedia 12
step 2 – Browsing for .HEX le 13
step 3 – Selecting .HEX le 13
step 4 – Uploading .HEX le 14
step 5 – Finish upload 15
Programming with mikroProg™programmer 16
mikroProg Suite™for PIC® Software 17
Programming with ICD2®or ICD3®programmer 18
4. Reset Button 20
5. Crystal Oscillator 22
6. MicroSD Card Slot 23
7. Touch Screen 24
8. Audio Module 26
9. USB connection 28
10. Accelerometer 30
11. Flash Memory 31
12. Pads 32
13. Pinout 33
14. Dimensions 34
15. Mikromedia Accessories 35
16. What’s Next 36
Table of Contents

Page 4
Introduction to mikromedia for PIC32®
The mikromedia for PIC32®is a compact
development system with lots of on-board
peripherals which allow development of devices
with multimedia contents. The central part of
the system is a 32-bit PIC32MX460F512L
microcontroller. The mikromedia for PIC32®
features integrated modules such as stereo MP3
codec, TFT 320x240 touch screen display,
accelerometer, USB connector, audio connector,
MMC/SD card slot, 8 Mbit ash memory, 2x26
connection pads and other. It comes pre-
programmed with USB HID bootloader, but can
also be programmed with external programmers,
such as mikroProg™or ICD2/3. Mikromedia is
compact and slim, and perfectly ts in the palm
of the hand, which makes it convenient platform
for mobile devices.

Page 5
Package Contains
Copyright ©2012 Mikroelektronika.
All rights reserved. MikroElektronika, MikroElektronika logo and other
MikroElektronika trademarks are the property of MikroElektronika.
All other trademarks are the property of their respective owners.
Unauthorized copying, hiring, renting, public performance
and broadcasting of this DVD
is strictly prohibited.
M
I
K
R
O
M
E
D
I
A
B
O
A
R
D
S
•
•
•
•
•
•
•
•
•
M
A
N
U
A
L
S
•
•
•
•
•
•
•
•
•
D
E
V
E
L
O
P
M
E
N
T
B
O
A
R
D
S
•
•
•
•
•
•
•
•
•
S
C
H
E
M
A
T
I
C
S
•
•
•
•
•
•
•
•
•
A
C
C
E
S
S
O
R
Y
B
O
A
R
D
S
•
•
•
•
•
•
•
•
•
E
X
A
M
P
L
E
S
•
•
•
•
•
•
•
•
•
A
D
D
I
T
I
O
N
A
L
S
O
F
T
W
A
R
E
•
•
•
•
•
•
•
•
•
C
O
M
P
I
L
E
R
S
•
•
•
•
•
•
•
•
•
M
I
K
R
O
C
,
M
I
K
R
O
B
A
S
I
C
,
M
I
K
R
O
P
A
S
C
A
L
C
O
M
P
I
L
E
R
S
•
•
•
•
•
•
•
•
•
D
R
I
V
E
R
S
•
•
•
•
•
•
•
•
•
P
R
O
G
R
A
M
M
E
R
S
A
N
D
D
E
B
U
G
G
E
R
S
•
•
•
•
•
•
•
•
•
PRODUCT DVD
www.mikroe.com
www.libstock.com
01 02
04 05
03
06
Damage resistant
protective box
mikromedia for PIC32®
development system
mikromedia for PIC32®
user’s guide
mikromedia for PIC32®
schematic
DVD with documentation
and examples
USB cable

Page 6
Key Features
16
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Connection Pads
TFT 320x240 display
USB MINI-B connector
CHARGE indication LED
LI-Polymer battery connector
3.5mm headphone connector
Power supply regulator
Serial Flash memory
RESET button
VS1053 Stereo mp3 coder/decoder
PIC32MX460F512L microcontroller
Accelerometer
Crystal oscillator
Power indication LED
microSD Card Slot
ICD2/3 connector
mikroProg connector
17
01
02
09

Page 7
System Specication
power supply
Via USB cable (5V DC)
board dimensions
81.2 x 60.5mm (3.19 x 2.38 inch)
weight
~50 g (0.11 lbs)
power consumption
58 mA with erased MCU
(when on-board modules are inactive)
03
06
07
08
11
10
12
13
14
15
16
04 05
17

Page 8
1. Power supply
You can apply power supply to the board
using MINI-B USB cable provided with
the board. On-board voltage regulators
provide the appropriate voltage levels
to each component on the board. Power
LED (GREEN) will indicate the presence of
power supply.
You can also power the board using Li-Polymer battery,
via on-board battery connector. On-board battery charger
circuit MCP73832 enables you to charge the battery
over USB connection. LED diode (RED) will indicate
when battery is charging. Charging current is ~250mA
and charging voltage is 4.2V DC.
Battery power supply
USB power supply
Figure 1-1: Connecting
USB power supply
Figure 1-2: Connecting Li-Polymer battery

Page 9
2
3
5
4
1
VCC-BAT
D1
PMEG3010ER
R44
3K9
Charging Current approx. 250mA
R39
4K7
VCC-3.3
E7
10uF
C40
2.2uF
R34
4K7
R6
4K7
VCC-BAT
VSENSE
VCC-SYS
VCC-SYS
R43
10K
R37
10K
R36
10K
VCC-3.3
STAT
R38
10K
R45
1K
VCC-3.3
E5
10uF
R35
10K
VCC-3.3
R49
4K7
M1
DMP2160UW
STAT
VSS
VBAT VDD
PROG
U5
MCP73832
Q4
BC846
Q5
BC846
FP2
FERRITE
VCC-USB
C29
2.2uF
VCC-3.3
R46
100K
E10
10uF
R47
220K
VCC-1.8
VCC-1.8
R50
0R
1
2
3
5
4
Vin
GND
EN ADJ
Vout
U3
MIC5205-ADJ
DATA BUS
LD2
CHARGE
VCC-BAT
VCC-1.8VREF-1.8
E11
10uF
FP3
FERRITE
CN1
BATT CONN
C28
10nF
VBUS
1D-
2D+
3ID
4GND
5
CN3
USB MINIB
VCC-SYS VCC-3.3
E3
10uF
E4
10uF
R26
2K2
Vout
3
Vin
1
2
GND
REG1
LD29080DT33
LD1
POWER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
HDR1
M1X26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
HDR2
M1X26
VCC-3.3 VCC-3.3
VCC-SYS
Figure 1-3: Power supply schematics

Page 10
2. PIC32MX460F512L microcontroller
The mikromedia for PIC32®development system comes with the
PIC32MX460F512L microcontroller. This high-performance 32-bit
microcontroller with its integrated modules and in combination with
other on-board modules is ideal for multimedia applications.
Key microcontroller features
- 1.56 DMIPS/MHz, 32-bit MIPS M4K Core;
- 512K Flash (plus 12K boot Flash);
- 32K RAM (can execute from RAM);
- 85 I/O pins;
- SPI, I2C, A/D;
- 16-bit, 32-bit Digital Timers;
- Internal Oscillator 8MHz, 32kHz;
- RTCC; etc.
Bus Matrix
Peripherial Bus
PIC32
MIPS M4K 32-bit core
- 80MHz, 1.5 DMIPS/MHz
- 5 Stage Pipeline, 32-bit ALU
Trace 32-bit
HW
Mul/Div
32 Core
Registers
Shadow Set
JTAG
Instruction Data
RTCC
Analog
Comparators
(2)
I2C
(2)
16 Ch
10-bit
ADCs
UARTs
(2)
Input
Capture
(5)
SPI
(2)
Output
Compare
PWM(5)
16-bit
Timers
(5)
Prefetch
Buffer Cache Flash SRAM Interrupt
Controller
GPIO
(85) VREG
DMA
4Ch
2-wire
Debug
USB
OTG
16-bit
Parallel
Port

Page 11
The microcontroller can be programmed in three ways:
01
02
03
Over USB HID mikroBootloader
Using mikroProg™external programmer
Using ICD2/3 external programmer
3. Programming the microcontroller
Figure 3-1:
PIC32MX460F512L
microcontroller

Page 12
Programming with mikroBootloader
You can program the microcontroller with bootloader which is
pre-programmed by default. To transfer .hex le from a PC to
MCU you need bootloader software (mikroBootloader USB
HID) which can be downloaded from:
After the mikroBootloader software is downloaded, unzip it to
desired location and start it.
Figure 3-2: USB HID mikroBootloader window
step 1 – Connecting mikromedia
01
01
To start, connect the USB cable, or if already connected
press the Reset button on your mikromedia board. Click the
Connect button within 5s to enter the bootloader mode,
otherwise existing microcontroller program will execute.
http://www.mikroe.com/downloads/get/1605/
mikrobootloader_pic32_v200.zip

Page 13
step 3 – Selecting .HEX le step 2 – Browsing for .HEX le
Figure 3-3: Browse for HEX Figure 3-4: Selecting HEX
01 01
02
01
01
02
Click the Browse for HEX button and from a
pop-up window (Figure 3.4) choose the .HEX le
which will be uploaded to MCU memory.
Select .HEX le using open dialog window.
Click the Open button.

Page 14
step 4 – Uploading .HEX le
Figure 3-5: Begin uploading Figure 3-6: Progress bar
01
01
01 01
To start .HEX le bootloading click the
Begin uploading button.
Progress bar enables you to monitor .HEX le upload-
ing.

Page 15
step 5 – Finish upload
Figure 3-7: Restarting MCU Figure 3-8: mikroBootloader ready for next job
01
01
02
Click OK button after the uploading process is nished
Press Reset button on mikromedia board and wait
for 5 seconds. Your program will run automatically

Page 16
The microcontroller can be programmed with mikroProg™
programmer and mikroProg Suite™for PIC®software. The
mikroProg™programmer is connected to the development
system via the CN6 connector, Figure 3-9.
mikroProg™is a fast
USB 2.0 programmer with
mikroICD™hardware In-Circuit
Debugger. Smart engineering allows
mikroProg™to support PIC10®, PIC12®, PIC16®,
PIC18®, dsPIC30/33®, PIC24®and PIC32®devices in
a single programmer. It supports over 570 microcontrollers
from Microchip®. Outstanding performance, easy operation and
elegant design are it’s key features.
Programming with mikroProg™
programmer
Figure 3-9:
Connecting mikroProg™to mikromedia™

Page 17
mikroProg Suite™for PIC®Software
mikroProg™programmer requires
special programming software called
mikroProg Suite™for PIC®. This
software is used for programming of
ALL Microchip®microcontroller families,
including PIC10®, PIC12®, PIC16®, PIC18®,
dsPIC30/33®, PIC24®and PIC32®.
Software has intuitive interface and
SingleClick™programming technology.
Just by downloading the latest version
of mikroProg Suite™your programmer
is ready to program new devices.
mikroProg Suite™is updated regularly,
at least four times a year, so your
programmer will be more and more
powerful with each new release.
Figure 3-10: Main Window of mikroProg Suite™for PIC®programming software
PIC32

Page 18
Figure 3-11:
Placing ICD2®
connector
The microcontroller can be also programmed with ICD2®
or ICD3®programmer. These programmers connects
with mikromedia board via ICD2 CONNECTOR BOARD.
Programming with
ICD2®or ICD3®programmer
In order to enable the ICD2®and ICD3®programmers to be connected to the
mikromedia board, it is necessary to provide the appropriate connector such as the
ICD2 CONNECTOR BOARD. This connector should be rst soldered on the CN5 connector.
Then you should plug the ICD2®or ICD3®programmer into it, Figure 3-11.
Figure 3-12:
Connecting ICD2®
or ICD3®programmer

Page 19
Figure 3-13: mikroProg™& ICD2 / ICD3 programmer connection schematic
ICD2/3
MCLR#
PGD2
PGC2
VCC-3.3
MCLR#
PGD2
PGC2
R15 100
R3 100
RB6
RB7
mikroProg
1
2
3
4
5
CN6
M1X5
1
2
3
4
5
6
CN5
M1X6
VCC-3.3
MCLR#
PGD2 PGC2
VCC-3.3
Vcap
E9 10uF
VDD
16
RE6
4RE5
3
RB0
25 RB1
24 RB2
23 RB3
22 RB4
21 RB5
20
RE7
5
RG6/SCK2
10
RG7/SDI2
11
VSS
15 RG9
14
RG8/SDO2
12
MCLR
13
RG15
1
VDD
2
RC1
6
RC2
7
RC3
8
RC4
9
RA0/TMS
17
RE8/INT1
18
RE9/INT2
19
RB11
35
AVDD
30
RB9
33 RB8 32
RB13
42 RB12 41
RB15
44 RB14 43
RF4
49
RF5
50
VSS
36
RB6
26
AVSS
31
RB10
34
RB7
27
VDD
37
RA9
28
RA10/VREF+
29
RA1
38
RF13
39
RF12
40
RD14
47
RD15
48
VSS
45
VDD
46
RC14 74
RC13 73
RD0 72
RD11 71
RD10 70
VDD 62
VSS 65
D+/RG2 57
RF3 51
U1RX/RF2 52
VUSB 55
D-/RG3 56
OSC2 64
RD8 68
OSC1 63
RD9 69
VSS 75
RA14 66
RA15 67
RA4 60
RA5 61
SCL2/RA2 58
SDA2/RA3 59
U1TX/RF8 53
VBUS 54
RD2 77
RF0 87
RD7 84 RD6 83 RD5 82 RD4 81
RE4 100
ENVREG 86
Vcap/VDDcore 85
RD1 76
RE0 93
RD3 78
RF1 88
RE1 94 RE2 98 RE3 99
RG13 97 RG12 96 RG14 95
RA7 92 RA6 91
RG0 90 RG1 89
RD13 80 RD12 79
U1
PIC32MX460F512L
C5
100nF
C6
100nF
C7
100nF
C8
100nF
VCC-3.3 VCC-3.3
VCC-3.3 VCC-3.3
VCC-3.3
C25
100nF
VCC-3.3
E8
10uF

Page 20
Board is equipped with reset button, which is located
at the top of the front side (Figure 4-2). If you want to
reset the circuit, press the reset button. It will generate
low voltage level on microcontroller reset pin (input). In
addition, a reset can be externally provided through pin
27 on side headers (Figure 4-3).
4. Reset Button
Figure 4-2: Frontal reset button
Figure 4-1: Location of additional reset button
You can also solder additional reset button
on the appropriate place at the back side
of the board, Figure 4-1.
NOTE