Mikrotron EoSens 3CXP User manual

Remarks, Notes and Warnings
MIKROTRON GmbH page 1 of 63
3CXP Camera
EoSens 3CXP Reference
Guide

Remarks, Notes and Warnings
page 2 of 63 MIKROTRON GmbH
3CXP Camera
Table of Content
Table of Content ........................................................................................................................... 2
About This Reference Guide.......................................................................................................... 6
Remarks, Notes and Warnings ............................................................................................................ 6
Registered Trademarks........................................................................................................................ 6
Conformity and Use ...................................................................................................................... 7
Supplements........................................................................................................................................ 8
Declaration of Conformity ................................................................................................................... 9
Warranty and Non-Warranty Clause................................................................................................. 10
Scope of Delivery ............................................................................................................................... 11
System Requirements........................................................................................................................ 12
Introduction ............................................................................................................................... 13
Most Important Features .................................................................................................................. 13
Hardware ................................................................................................................................... 14
Rear Side of the Camera with DIN Connector ................................................................................... 14
Rear Side of the Camera with 5W5 Connector.................................................................................. 15
Connecting a Frame Grabber ............................................................................................................ 15
DIN Connector ............................................................................................................................... 16
5W5 Connector.............................................................................................................................. 17
Connecting an External Power Supply............................................................................................... 18
12 Pin Hirose Connector and I/O-Signals....................................................................................... 18
6 Pin Hirose and I/O-Signals .......................................................................................................... 19
Status LED .......................................................................................................................................... 20
Resolution and Speed........................................................................................................................ 21
Cleaning the Sensor or the Lens ........................................................................................................ 21
First Steps................................................................................................................................... 22
Initial Setup........................................................................................................................................ 22
Serial Number and Firmware............................................................................................................. 22
Powering-up the Camera................................................................................................................... 22
Configure Your 3CXP Camera ...................................................................................................... 23
GenICam Standard............................................................................................................................. 23
Camera Registers........................................................................................................................ 24
Bootstrap registers ............................................................................................................................ 25
Standard ........................................................................................................................................ 26
Revision.......................................................................................................................................... 27
XmlManifestSize ............................................................................................................................ 27

Remarks, Notes and Warnings
MIKROTRON GmbH page 3 of 63
3CXP Camera
XmlManifestSelector ..................................................................................................................... 27
XmlVersion[XmlManifestSelector] ................................................................................................ 28
XmlSchemeVersion[XmlManifestSelector].................................................................................... 28
XmlUrlAddress [XmlManifestSelector].......................................................................................... 29
Iidc2Address .................................................................................................................................. 29
DeviceVendorName....................................................................................................................... 30
DeviceModelName ........................................................................................................................ 30
DeviceManufacturerInfo ............................................................................................................... 30
DeviceVersion................................................................................................................................ 31
DeviceSerialNumber ...................................................................................................................... 31
DeviceUserID ................................................................................................................................. 31
Manufacturer-specific Addresses.................................................................................................. 32
ConnectionReset............................................................................................................................ 32
DeviceConnectionID ...................................................................................................................... 32
MasterHostConnectionID .............................................................................................................. 33
ControlPacketSizeMax................................................................................................................... 33
StreamPacketSizeMax ................................................................................................................... 33
ConnectionConfig .......................................................................................................................... 34
ConnectionConfigDefault .............................................................................................................. 34
TestMode....................................................................................................................................... 35
TestErrorCountSelector ................................................................................................................. 35
TestErrorCount[TestErrorCountSelector]...................................................................................... 35
TestPacketCountTx[TestErrorCountSelector]................................................................................ 36
TestPacketCountRx[TestErrorCountSelector] ............................................................................... 36
HsUpConnection............................................................................................................................ 36
Acquisition Control ............................................................................................................................ 37
AcquisitionMode............................................................................................................................ 37
AcquisitionStart ............................................................................................................................. 37
AcquisitionStop.............................................................................................................................. 38
TriggerSelector............................................................................................................................... 38
TriggerMode [TriggerSelector] ...................................................................................................... 38
TriggerSource [TriggerSelector]..................................................................................................... 39
TriggerActivation [TriggerSelector] ............................................................................................... 39
TriggerSoftware ............................................................................................................................. 40
ExposureMode............................................................................................................................... 40
ExposureTime ................................................................................................................................ 40
ExposureTimeMax ......................................................................................................................... 41

Remarks, Notes and Warnings
page 4 of 63 MIKROTRON GmbH
3CXP Camera
AcquisitionFrameRate ................................................................................................................... 41
AcquisitionFrameRateMax ............................................................................................................ 41
TestImageSelector ......................................................................................................................... 42
DualSlopeEnable............................................................................................................................ 42
DualSlope....................................................................................................................................... 43
Device Control ................................................................................................................................... 44
DeviceReset ................................................................................................................................... 44
Image Format Control........................................................................................................................ 45
Width ............................................................................................................................................. 45
Height ............................................................................................................................................ 45
OffsetX ........................................................................................................................................... 46
OffsetY ........................................................................................................................................... 46
SensorWidth .................................................................................................................................. 46
SensorHeight ................................................................................................................................. 46
WidthMax ...................................................................................................................................... 47
HeightMax ..................................................................................................................................... 47
PixelFormat.................................................................................................................................... 47
TapGeometry................................................................................................................................. 48
Image1StreamID ............................................................................................................................ 48
DeviceScanType............................................................................................................................. 48
User Set Control................................................................................................................................. 49
UserSetSelector ............................................................................................................................. 49
UserSetLoad[UserSetSelector] ...................................................................................................... 49
UserSetSave[UserSetSelector]....................................................................................................... 50
UserSetDefaultSelector ................................................................................................................. 50
Analog Control................................................................................................................................... 51
BlackLevel ...................................................................................................................................... 51
Gain................................................................................................................................................ 51
Custom Features................................................................................................................................ 52
DeviceInformationSelector............................................................................................................ 52
DeviceInformation[DeviceInfoSelector] ........................................................................................ 53
FixedPatternNoiseReduction......................................................................................................... 54
Firmware and Update ................................................................................................................. 55
Firmware Updater ............................................................................................................................. 55
Technical Data ............................................................................................................................ 56
Sensor ................................................................................................................................................ 56
Camera............................................................................................................................................... 56

Remarks, Notes and Warnings
MIKROTRON GmbH page 5 of 63
3CXP Camera
Sensor Defect Specifications ....................................................................................................... 57
Spectral response ....................................................................................................................... 58
Sensitivity without UV/IR Cut Filter................................................................................................... 58
Sensitivity with UV/IR Cut Filter ........................................................................................................ 59
Bayer Color Filter........................................................................................................................ 60
Bayer Pattern..................................................................................................................................... 60
Dimensions of MC3086/3087 ...................................................................................................... 61
Rear View........................................................................................................................................... 61
Side View ........................................................................................................................................... 61
Dimensions of MC3082/MC3083 ................................................................................................. 62
Rear View........................................................................................................................................... 62
Side View ........................................................................................................................................... 62
3CXP Camera Reference Guide V2.0 ......................................................................................... 63

Remarks, Notes and Warnings
MIKROTRON GmbH page 6 of 63
3CXP Camera
About This Reference Guide
This reference guide contains helpful information to install and operate 3CXP cameras of the type MC3082 and
MC3086 (monochrome) as well as MC3083 and MC3087 (color). It has been produced with care. Nevertheless,
information might be erroneous or incomplete. MIKROTRON cannot be held responsible for any problems
resulting from incomplete or erroneous information.
In case you detect errors or need further information, please inform us via mail: [email protected]
or call [phone].
We highly recommend, reading this reference guide carefully.
This reference guide is subject to change without notice.
Remarks, Notes and Warnings
This reference guide contains remarks, notes and warnings that are helpful and often important in order to
avoid data loss or camera damage. They are emphasized as follows:
Remark
Hints and other helpful information
Note
Hints concerning frame quality, timeouts, or other
WARNING
Important information concerning data loss or camera damage
Registered Trademarks
In this reference guide the following products are registered trademarks:
CoaXPress®
EoSens®
GenICam®
In the following, these product names are not specially marked as registered trademarks. Nevertheless, these
product names have not to be used in other context without the trade mark sign!

Registered Trademarks
MIKROTRON GmbH page 7 of 63
3CXP Camera
Conformity and Use
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These requirements are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions given in this reference guide, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will have to correct the interference at its own expense.
Remark: You are herewith cautioned that any changes or modifications not expressly approved in this
reference guide could void your authority to operate this equipment.
制造说明：
此设备的生产与测试依照 FCC 条例第 15 条条例，符合 A类电子设备标准。产品提供在商用使用环境中的合理
保护，以防止使用过程中可能涉及到的损害。
此设备会产生、使用并可发射出无线电波，如果未按照本手册中所述安装和使用，可能会对无线通信设备产
生干扰。如本设备在居民区操作出现干扰等情况，用户需要自费处理。
备注：请注意，如未按照此使用说明操作而自行更改设备，那么您将无权使用本设备。
規制適合宣言とご使用について （米国 FCC）
この機器は、FCC 規則のパート 15 に定められたクラス Aデジタル装置に関する規制要件に基づい
て所定の試験が実施され、その適合が認証されています。 これらの規制要件は、商業環境において
機器を使用する際、有害な干渉に対する妥当な保護を提供するために設けられています。 この機器は
、無線周波数エネルギーを生成かつ利用するとともに、放射することもあります。 このリファレン
スガイドの指示に従って設置および使用が行われない場合は、無線通信に有害な干渉を引き起こす恐
れがあります。 この機器を住宅地で利用すると有害な干渉を起こすこともあり、その場合、使用者
は自己負担において適切な対策を講じる必要があります。
注意事項： このリファレンスガイドに明示的に承認していない変更や修正を行った場合には、本
製品を使用する権利が無効となることがあります。

Supplements
page 8 of 63 MIKROTRON GmbH
3CXP Camera
Supplements
For customers in Canada
This apparatus complies with the Class A limits for radio noise emissions set out in Radio Interference
Regulations.
Pour les utilisateurs au Canada
Cet appareil est conforme aux normes Classe A pour bruits radioélectriques, spécifiées dans le Règlement sur le
brouillage radioélectrique.
Life Support Applications
The products described in this reference guide are not designed for use in life support appliances, or devices
and systems where malfunction of these products can reasonably be expected to result in personal injury.
MIKROTRON customers using or selling these products for use in such applications do so at their own risk and
agree to fully indemnify MIKROTRON for any damages resulting from such improper use or sale.

Declaration of Conformity
MIKROTRON GmbH page 9 of 63
3CXP Camera
Declaration of Conformity
Manufacturer: MIKROTRON GmbH
Address: Landshuter Str. 20-22
D-85716 Unterschleissheim / Germany
Product: Cameras MC3082 / MC3086 and MC3083 / MC3087
We herewith declare under our sole responsibility that the dedicated products are in conformity with the
following EU directives:
Title
EU Directive
RoHS Directive on the Restriction of the Use of Certain
Hazardous Substances in Electrical and Electronic Equipment
2011/65/EU
Approximation of the laws of the Member States relating to
electromagnetic compatibility and repealing Directive
89/336/EEC
2004/108/EC
During conformity-testing the following standards were consulted:
Title
EU Standard
Information technology equipment - Immunity
characteristics - Limits and methods of measurement
EN 55024:1998 + A1:2001 + A2:2003
Information technology equipment - Radio disturbance
characteristics - Limits and methods of measurement
EN 55022:2006 + A1:2007
Unterschleissheim, May 06, 2015 Dipl. Kfm. Christian Pilzer (CEO)

Warranty and Non-Warranty Clause
page 10 of 63 MIKROTRON GmbH
3CXP Camera
Warranty and Non-Warranty Clause
Warranty is described in §8 of our General Terms and Conditions which can be downloaded on MIKROTRONS’
webpage: www.mikrotron.de
In addition, take the following non-warranty clauses into account:
WARNING
The camera does not contain serviceable parts. Do not open
the body of the camera. If the camera has been opened, the
warranty will be void.
The camera may only be used with a supply voltage
according to the camera specification. Connecting a lower
or higher supply voltage, AC voltage, reversal polarity or
using wrong pins of the power connector may damage the
camera. Doing so will void warranty.
Our warranty does not protect against accidental damage,
loss, or acts of nature.
MIKROTRON cannot be held responsible for the loss of
data. We recommend a backup plan.
Before sending back the camera, ask for a RMA number and form either by:
phone: +49 - 89 - 7263 4250 or by
e-mail: [e-mail]
In case of warranty, please, make a note
of the camera type and serial number
and send the camera back to your
distributor. If no distributor is available,
send it back to MIKROTRON.
You find all necessary information on the
identification plate of the camera.

Scope of Delivery
MIKROTRON GmbH page 11 of 63
3CXP Camera
Scope of Delivery
The following components are part of delivery. Please check whether the delivery is complete,
before you start to install the camera:
Camera MC308x
C-Mount/F-Mount adapter (as ordered)
MIKROTRON’s Support CD
Optional:
several lenses www.mikrotron.de/en
DIN 1.0/2.3: four bundle cable KKRDDINDINxx/6Gx4 with DIN 1.0/2.3 connector at
both ends (4x); available in lengths of 5, 10, 15 or 20 m
Remark: The triangle on the connector indicates connection 1.
DIN 1.0/2.3: cable KKRDDINBNCxx/6Gx4 with DIN 1.0/2.3 at one end and 4 BNC
connectors at the other; available in cable lengths of 5, 10, 15, 20 or 25m

System Requirements
page 12 of 63 MIKROTRON GmbH
3CXP Camera
5W5: there are several cables (KKRD5W5BNCxx) for 6 GHz with a length of 5, 10, 15,
20 m or longer available. Please, contact your sales representative
external power supply unit:
MC3086/MC3087: NTCAM132x (12 V/2.5 A) with 12 pin Hirose connector
and 5 m cable
MC3082/MC3083: NTCAM13xx/NTCAM13XX10 with 6 pin Hirose connector
and 5/10 m cable
F-mount adapter
System Requirements
In order to use the MC308x camera you need:
image processing system, e.g.: PC and software
completely installed frame grabber (Device Driver, Software,...)
CoaXPress cable either with DIN 1.0/2.3 or 5W5 connector
if wanted, an external power supply (NTCAM132x or NTCAM13xx)
All cables, connectors and frame grabber have to be CoaXPress V1.1 compliant. Please, read the
application note AN0036 for more information on tested frame grabbers.

Most Important Features
MIKROTRON GmbH page 13 of 63
3CXP Camera
Introduction
The EoSens 3CXP family includes the cameras MC3082 and MC3086 (monochrome) as well as
MC3083 and MC3087 (color). All 3CXP cameras are CoaXPress compliant. These high-speed CMOS
cameras come with a 3 Megapixel sensor of 1696 (H) x 1710 (V) and are widely configurable and
scalable to fit to your needs. Furthermore, 3CXP cameras are highly photo sensitive and reach 1270
V.m²/W.s at 600 nm with micro lens. This sensitivity allows using the sensor in a great variety of
lighting conditions.
Using the CoaXPress high-speed interface technology a transfer speed of up to 1.9 GByte/s to
transfer image data can be achieved. 3CXP cameras support CoaXPress connection speeds from 1.25
to 5.00 Gbps.
The camera offers a very high frame rate of over 560 fps at full resolution. By defining a Region of
Interest (ROI), you can increase this frame rate by 1000ths of fps in order to optimize the resolution
and frame rate ratio.
A compact and solid full metal housing protects the camera’s electronics to make sure that it will
work properly in heavy industrial surroundings. Shielded coaxial cables as recommended by the
CoaXPress standard are a perfect combination.
3CXP cameras can be equipped with standard C-Mount or F-Mount lenses made for industrial
purpose.
Most Important Features
The most important features of 3CXP cameras are:
small, compact housing (page 61)
3 Megapixel high speed CMOS sensor
global shutter
monochrome or color (Bayer Filter)
CXP connection speed of 1.250, 2.500, 3.125 and 5.000 Gbps
8 µm2pixels
high resolution of 1696 x 1710 pixels
8 bit pixel output (256 gray levels)
1” optical format
up to 560 fps @ full resolution
sensitivity of 1270 V.m²/W.s at 600 nm
dual slope (up to 80 dB optical dynamic range)
asynchronous trigger
trigger frequency of 150 (one edge) and 300 kHz in AnyEdge mode
arbitrary region of interest (ROI)
over 17,236 frames/s with reduced resolution
communication and image transfer via CoaXPress interface (CXP1, CXP2, CXP3 and
CXP5)
wide power supply range of 12 –24V

Rear Side of the Camera with DIN Connector
page 14 of 63 MIKROTRON GmbH
3CXP Camera
Hardware
3CXP cameras are available with 5W5 (MC8082/8083) or DIN connector (MC-3086/3087). All
versions come with the same sensor providing a resolution of 1696 x 1710 pixels. The color versions
are equipped with a Bayer color filter at the top of the sensor. This filter will code the color
information in the image pixels.
Table A: 3CXP camera features
Camera
Data width
[bit]
Mono: M
Color: C
Lens
adapter
Link
speed
Max. frame rate
@ 1696 x 1710
Connector Type
MC3082
8
M
C/F
CXP-5
566 fps
5W5
MC3083
8
C
C/F
CXP-5
566 fps
5W5
MC3086
8
M
C/F
CXP-5
566 fps
DIN1.0/2.3
MC3087
8
C
C/F
CXP-5
566 fps
DIN1.0/2.3
Rear Side of the Camera with DIN Connector
At the back of the cameras MC3086/3087 the DIN1.0/2.3 connector and the power connector are to
be found. The DIN connector is used to connect the camera with a CoaXPress frame grabber and to
supply the camera with power (power-over-coax, so called PoCXP).
Alternatively, a 12 pin Hirose power connector is available to connect an external power supply.
Remark: In order to connect an external trigger take the pinning of the Hirose connector on
page 17 into account and read the trigger settings starting on page 38.
CoaXPress DIN 1.0/2.3 connector providing PoCXP
12 pin
power
connector
LED

Rear Side of the Camera with 5W5 Connector
MIKROTRON GmbH page 15 of 63
3CXP Camera
Rear Side of the Camera with 5W5 Connector
At the back of the camera the DIN1.0/2.3 connector and the power connector are to be found. The
DIN connector is used to connect the camera with a CoaXPress frame grabber and to supply the
camera with power (power-over-coax, so called PoCXP).
Alternatively, a 12 pin Hirose power connector is available to connect an external power supply.
Connecting a Frame Grabber
At the time being, the CoaXPress standard describes 4 connections for data transmission between
camera and frame grabber. The transmission speed of a 3CXP camera can either be set to 1.25, 2.5,
3.125 or 5 Gbit/s. The possible cable length depends on the cable type used and the transmission
speed. The following table gives examples. These values can only be reached if the signal quality
meets the requirements of the CXP-1.1 specification.
Table B: Maximal cable length depending on transmission speed
CXP type
Transmission speed
Max. cable length
RG59 style
CXP-1
1.25 Gbit/s
up to 130 m
CXP-2
2.5 Gbit/s
up to 110 m
CXP-3
3.125 Gbit/s
up to 100 m
CXP-5
5 Gbit/s
up to 60 m
4x CXP-5
4*5 Gbit/s = 20 Gbit/s
up to 60 m
Remark: If several connections are used, all connections will have to be run with the same
transmission speed.
6-pin power
connector
5W5 connector
for CoaXPress
LED

Connecting a Frame Grabber
page 16 of 63 MIKROTRON GmbH
3CXP Camera
DIN Connector
In order to connect a MC4086/4087 camera with a frame grabber, use any compatible CoaXPress
cable with DIN connector. MIKROTRON offers cables with the following connectors (page 11):
DIN<->DIN (KKRDDINDINxx/6Gx4)
DIN<->BNC (KKRDDINBNCxx/6Gx4)
WARNING
Please, carefully connect and release the socket with
the DIN1.0/2.3 connector. Connect them precisely to
avoid deformation of the connectors or other
damages!
If connecting a frame grabber via BNC, keep the order from left to right when making one, two, or
four connections. The inner left connector (1) is the master connector and always has to be
connected. All connections are hot-pluggable.
No. of
connections
Connector
combination
1
2
1+2 (link)
4
1+2+3+4 (link)
When using the DIN connector with a cable from MIKROTRON (e.g.: KKRDDINDINxx/6Gx4, use the
pin with the triangle on the connector housing as pin 1.
The assignment of the DIN-cables KKRDDINDINxx/6Gx4 and KKRDDINBNCxx/6Gx4 connector pins is
as follows:
DIN connector pin
Cable color
Function
1 (triangle)
blue
TX channel 0
2
white
TX channel 1
3
green
TX channel 2
4
red
TX channel 3

Connecting a Frame Grabber
MIKROTRON GmbH page 17 of 63
3CXP Camera
5W5 Connector
In order to connect a MC3082/3083 camera with a frame grabber, use MIKROTRON’s cable
KKRD5W5BNCxx for 6 GHz and different lengths.
WARNING
Please, carefully connect and release the socket with
the 5W5 connector. Connect them precisely to avoid
deformation of the connectors or other damages!
If connecting a frame grabber via BNC, keep the order from right to left. The outer right connector
(1) is the master connector and always has to be connected. All connections are hot-pluggable.
Connector 5 is not used.
Table 1: Assignment of the cable of the 5W5 connector
5W5 Connector Pin
Cable Color
Function
1
red
TX channel 0
2
green
TX channel 1
3
blue
TX channel 2
4
white
TX channel 3
5
yellow
TX channel 0 (not yet
assigned, do not use)

Connecting an External Power Supply
page 18 of 63 MIKROTRON GmbH
3CXP Camera
Connecting an External Power Supply
All 3CXP cameras can either be supplied with power over coax (PoCXP) or via the Hirose connector
with an external power supply. MC3082/3083 cameras are equipped with a female 6-pin and
MC3086/3087 with a female 12 pin Hirose connector.
12 Pin Hirose Connector and I/O-Signals
In case you prefer an external power supply for MC3086/3087, connect it with the 12 pin Hirose
connector (HR10A-10R-12PB (71)) at the back of the camera. The DC power supply has to deliver 12 -
24 V DC (7 W) (page 11).
The 12 pin connector provides a strobe signal (STRBOUT) which is low during exposure and two inputs
for an external trigger (page 39).
In case you assemble your own cable, pay attention to the pinning described below.
Table C: Pinning of the Hirose 12 pin power connector
Pin
Signal
Pin
Signal
1 + 12
GND
5
TRIGLine0 GND
2 + 11
VIN
(8 24 V)
6
TRIGLine0 IN
3
STRBGND
9
TRIGLine1 GND
4
STRBOUT
10
TRIGLine1 IN
Remarks:
The I/O pins 7 and 8 are not in use.
The I/O standard 3.3V LVTTL applies to all signal I/Os (STRB + TRIG).
WARNING
The power connector of the camera has to be connected with a
DC power supply providing 12 to 24 V DC. Connecting a lower or
higher supply voltage, an AC voltage, reversal polarity (+/-) or
using wrong pins of the power connector may damage the
camera and will void warranty.

Connecting an External Power Supply
MIKROTRON GmbH page 19 of 63
3CXP Camera
6 Pin Hirose and I/O-Signals
The power connector of the cameras MC3082/MC3083 has to be connected via the 6-pin Hirose
connector (HR10A-7P-6S) with a DC supply voltage between 12 and 24 V at a power consumption of
7W max. The DC power supply unit is connected to a dedicated connector at the back side of the
camera. Please, take attention to the pin wiring of the connector as described below.
The 6 pin connector provides a strobe signal (STRBOUT) which is low during exposure.
In case you assemble your own cable, pay attention to the pinning described below.
Table 2: Pinning of the 6 pin power connector
Pin
Signal
Pin
Signal
1
VCC
6
GND
2
VCC
5
GND
3
STRBOUT
(3.3 V LVTTL
I/O standard)
4
GNDSTRB
WARNING
The power connector of the camera has to be connected with a
DC power supply providing 12 to 24 V DC. Connecting a lower or
higher supply voltage, an AC voltage, reversal polarity (+/-) or
using wrong pins of the power connector may damage the
camera and will void warranty.

Status LED
page 20 of 63 MIKROTRON GmbH
3CXP Camera
Status LED
A multi-color LED on the backplane of the camera indicates camera and CXP connection states
according to the CXP 1.1 standard.
Table D: LED indications
LED State
Indication
OFF
no power
solid orange
system is booting
slow pulse red
powered, but nothing connected
(not applicable to a device reliant on PoCXP power)
fast flash alternate green/orange
connection detection in progress, PoCXP active
fast flash orange
connection detection in progress, PoCXP not in use
slow flash alternate red/green
device incompatible, PoCXP active
slow flash alternate red/orange
device incompatible, PoCXP not in use
solid green
device connected but no data being transferred
slow pulse orange
device connected, waiting for event (e.g. trigger)
fast flash green
device connected, data being transferred
slow flash alternate green/orange
connection test packets being sent
red - 500 ms pulse
error during data transfer
slow flash alternate red/green/orange
compliance test mode enabled
fast flash red
system error
Remark: If the LED signals the end of a successfully firmware update (green –slowly pulsating),
the camera can be switched off.
WARNING
Never switch off the camera during a firmware update.
Otherwise the camera might be permanently damaged.
status LED