MiLAN MIL-160T User manual

Ethernet Media Converters
MIL-160T/ MIL-170T
•Allows long fiber segments to
be connected without optical
attenuation
•Ensures compatibility with all
10BASE-FL and non-10BASE-T
802.3 Ethernet equipment
•Allows data transmissions of up
to 15 km over full-duplex fiber
cabling
•Fits easily into small spaces
The 160T Fiber-Twist is an unshielded twisted pair (UTP) to single-mode fiber optic media
converter designed to interconnect standard LAN-based Ethernet ports at distances up to 4 km.
The unit features MiLAN’s LinkSentry™ Remote Sensing Technology, which enables the 160T to
pass through line failures when signals are lost, as well as looping back failures, in the event one
strand is damaged in a cable.
The 170T Fiber-Twist single-mode duplexer is UTP to single-mode fiber optic media converter. It
is designed to interconnect half- or full-duplex LAN-based Ethernet ports at recommended
distances of up to 15 km. The 160T and 170T convert Ethernet media without adding the delay
associated with repeaters and will not add to your repeater budget.
ST connectors are used for single-mode fiber optic cabling. A shielded RJ-45 connector is used
for the UTP 10BASE-T port.
Datasheet
Media Converters802.11b WirelessPrint Servers Switches
MiLAN Technology
1329 Moffett Park drive
Sunnyvale, CA 94089
1-800-466-4526
www.milan.com
*
Transceivers

Ethernet Media Converters
MIL-160T / MIL-170T
Features
• Converts UTP to single-mode fiber optic cabling without
adding delay
• Switch selectable LinkSentry
• Supports both half- or full-duplex Ethernet
• Automatic sensing of low-light level conditions disables
link upon detection
• IEEE 802.3 compliant
• Small form factor
10BASE-T
> IEEE 802.3 compliant UTP interface
RJ-45 Connector
Type: 8-position shielded RJ-45 receptacle for:
MDI
1: TX+ 5: NC
2: TX- 6: RX-
3: RX+ 7: NC
4: NC 8: NC
MDI-X
1: RX- 5: NC
2: RX+ 6: TX-
3: TX+ 7: NC
4: NC 8: NC
10BASE-FL
IEEE 802.3 compliant, FOIRL
Regulatory Approvals
FCC Class A
UL 1950
CSA 950
CE Marked
- EN55022 Class B
- EN50082
EN60950
LED’s
Provides a complete set of diagnostic LEDs to analyze your network
activity at a glance.
LEDs light to indicate:
RCV/TP: Receiving data packets from the UTP network
UTP LINK: UTP link is intact
POWER: Receiving power from wall adapter
RCV/FIBER: Receiving data packets from the fiber port
FIBER LINK: Fiber link is intact
Environmental
Operating temperature: 0 to 50ºC (32ºF to 122ºF)
Storage temperature: -20ºC to 70ºC (-4ºF to 158ºF)
Relative humidity: 10% to 90% (non-condensing)
Altitude: 0 to 3,660 m (0 to 12,000 feet)
Power Requirements
Voltage: 16 - 20 VAC
Amperage: 200 mA
Power rating: 10 W
Fiber Characteristics
Unit Typical
160T 170T
Diameter
µm 8 - 9 8 - 9
TX-RX Wavelength
nm 1300 1300
TX Launch power
dBm -31 -19
RX- Sensitivity
dBm -36 -36
Dynamic range
dBm 5 17
Ordering Information
MIL-160T Ethernet UTP to SMF 4 km
MIL-160TIN (International)
MIL-170T Ethernet UTP to SMF 15 km
MIL-170TIN (International)
Warranty
Comprehensive 5 years, see product manuals for details
MiLAN Technology
1329 Moffett Park Drive
Sunnyvale, CA 94089
1-800-466-4526
www.milan.com
Milan Technology reserves the right to change specifications or other product information without notice. This publication could include technical
inaccuracies or typographical errors. Milan Technology provides this publication “as is” without warranty of any kind, either expressed or implied,
including implied warranties of merchantability or fitness for a particular purpose. If your jurisdiction does not allow disclaimer of expressed or implied
warranties in certain transactions, this disclaimer may not be applicable.
Milan Technology, the Milan Technology logo are trademarks of MiLAN Technology. All other trademarks are the property of their respective holders.
® Copyright 2003 MiLAN Technology