MiLAN MIL-C2112 User manual

Installation Guide: MIL-C2112
ST - Type
Connector
LEDs RJ-45
Connector
The MIL-C2112 comes equipped with ST-type connectors and
supports Fast Ethernet in both half and full-duplex mode. For
network budget constraint, the MIL-C2112 uses 150 nanoseconds
(approximately 30 meters of cable) during conversion in each
direction.
To maximize the fiber cable distance, use one meter of category 5
(CAT 5) UTP cable when connecting directly to a node (subject to
fiber budget of 16dBm and collision domain restrictions). In full-
duplex environments, up to 100m of CAT 5 UTP and 2Km of
1300 nm multi-mode fiber cable can be used.
-Launch power: -19dB
-Receive sensitivity: -30dB
•
•
•
•
•
•
•
•
•.
•
•
Regulatory Approval
Canadian EMI Notice
European Notice
Trademarks
To Contact MiLAN Technology
FCC Class A
UL 1950
CSA C22.2 Number 950
EN60950
CE
- EN55022 Class B
- EN50082-1
This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada.
Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage
Directive (73/23/EEC) issued by the commission of the European Community Compliance with these directives
implies conformity to the following European Norms:
EN55022 (CISPR 22) - Radio Frequency Interference
EN50082-1 (IEC801-2, -3, -4) - Electromagnetic Immunity
EN60950 (IEC950) - Product Safety
Five-Year Limited Warranty
MiLAN Technology warrants to the original consumer or purchaser that each of it’s products, and
all components thereof, will be free from defects in material and/or workmanship for a period of
five years from the original factory shipment date. Any warranty hereunder is extended to the
original consumer or purchaser and is not assignable.
MiLAN Technology makes no express or implied warranties including, but not limited to, any
implied warranty of merchantability or fitness for a particular purpose, except as expressly set
forth in this warranty. In no event shall MiLAN Technology be liable for incidental or
consequential damages, costs, or expenses arising out of or in connection with the performance
of the product delivered hereunder. MiLAN Technology will in no case cover damages arising
out of the product being used in a negligent fashion or manner.
© 2000 MiLAN, the MiLAN logo and MiLAN Technology are either trademarks or registered
trademarks of Digi International, Inc. in the United States and/or other countries. All other
trademarks are the property of their respective holders.
For prompt response when calling for service information, have the following information ready:
Product serial number and revision
Date of purchase
Vendor or place of purchase
You can reach MiLAN Technology technical support at:
E-mail: [email protected]
Telephone: [phone]
Fax: [phone]
MiLAN Technology
1299 Orleans Drive
Sunnyvale, CA 94089-1138
United States of America
Telephone: [phone]
Fax: [phone]
http://www.milan.com
[email protected]
© Copyright 2000 MiLAN Technology Printed in the USA P/N: 90000209 Rev. A

Installation
1. Attach a UTP cable from the network to the RJ-45 port.
(Use screened UTP cabling for CISPR 22 class B installation.)
2. Cross-connect the fiber cables: Attach both fiber cables
TX to RX and RX to TX from the fiber network cabling to the
ST-type connectors on the MIL-C2112.
3. Apply power to the unit:
A. Insert the power adapter’s receptacle into the power plug.
B. Insert the power adapter into a wall outlet.
Diagnostic LEDs and Conditions Indicated
There are five LEDs, including power and:
•
•
•
•
MDI-X/MDI Switch
The MDI-X/MDI switch allows for quick configuration
of the 100BASE-TX port. Cables used when the switch is
in the MDI-X position (the “left” position):
• For a hub/repeater , use a swap cable (pins are
connected 1 to 3, 2 to 6, 3 to 1, and 6 to 2)
• For a workstation/PC, use a straight-through cable
(pins are connected 1 to 1, 2 to 2, 3 to 3, and 6 to 6)
Cables used when the switch is in the MDI position (the
“right” position):
• For a hub/repeater , use a straight-through cable (pins
are connected 1 to 1, 2 to 2, 3 to 3, and 6 to 6)
• For a workstation/PC port, use a swap cable (pins are
Figure 1. Inside of the MIL-C2112
Link Sentry Configuration
The Link Sentry feature on the MIL-C2112 is configured through
a 4-position DIP switch (refer to Figure 1).
Default setting for the DIP switches: All switches are in the “up”
Position.
Link Sentry allows users to add new management tools to the network.
When enabled, it monitors the selected receiver port and, if the Link
test signal is not seen, the unit will stop sending a signal through the
selected transmit port.
The following table shows which Link Sentry feature is enabled.
Table 1. Link Sentry Features
1 (down) Fiber port Fiber port
2 (down) UTP port UTP port
3 (down) UTP port Fiber port
4 (down) Fiber port UTP port
MDI-X/MDI
Switch
RJ-45 Female
Connector
ST-Type
Connectors
4
3
2
1
LEDs
4-pin DIP Switch
connected 1 to 3, 2 to 6, 3 to 1, and 6 to 2)
MDI-X MDI
1234568
7
Pin 1=RX+
Pin 2=RX-
Pin 3=TX+
Pin 6=TX-
Pin 1=TX+
Pin 2=TX-
Pin 3=RX+
Pin 6=RX-
Switch Losing Link on RX of Stop sending Link on TX of
Figure 2. RJ-45 Pinouts
TX/ACTIVE: Receiving packets from the 100BASE-TX port.
FX/ACTIVE: Receiving packets from the 100BASE-FX port.
TX/LINK: An active connection on the 100BASE-TX port.
FX/LINK: An active connection on the 100BASE-FX port.
Note: For two MIL-C2112s used back-to-back and UTP-to-UTP,
all DIP switches must be enabled in the “down” position on the first
MIL-C2112. On the second MIL-C2112, set switches 1 and 4 in the
“down” position.
To enable Link Sentry with two MIL-C2112s used back-to-back and
fiber-to-fiber, enable all DIP switches in the “down” position on the
first MIL-C2112. On the second MIL-C2112, enable switches 2 and 3
in the “down” position.