MiLAN MIL-225C User manual

Installation Guide MIL-225C
® Copyright 1997 MiLAN Technology Printed in the USA P/N: 90000063 Rev. B
Regulatory Approvals
• FCC Class A
• UL 1950
• CSA 22 No. 950
• EN60950
• CE
– EN55022 Class B
– EN50082-1
Canadian EMI Notice
This Class Adigital apparatus meets all the requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleir du Canada.
European Notice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low
Voltage Directive (73/23/EEC) issued by the commission of the European Community. Compliance
with these directives implies conformity to the following European Norms:
• EN55022 (CISPR 22) - Radio Frequency Interference
• EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity
• EN60950 (IEC950) - Product Safety
To Contact MiLAN Technology
For prompt response when calling for service information, have the following information ready:
• Product serial number and rev.
• Date of purchase
• Vendor or place of purchase
You can reach MiLAN Technical Support at 408/744-2751
Or E-mail at [email protected]
Address:
1299 Orleans Drive
Sunnyvale, CA 94089
Voice:
408/744-2775
Fax:
408/744-2793
Web:
www.milan.com
MIL-225C
100BaseFX/OC-3
Single-mode to Multi-mode
Fiber Converter
Installation Guide
Multi-mode to Single-mode
and
Single-mode to Multi-mode
This guide includes the following information:
• “Introduction” on page 2
• “Installation” on page 3
• “Theory of Operation” on page 4
• “Specification” on page 5
Five-Year Limited Warranty
MiLAN Technology warrants to the original consumer or purchaser that each of its products,
and all components thereof, will be free from defects in material and/or workmanship for a
period of five years from the original factory shipment date. Any warranty hereunder is
extended to the original consumer or purchaser and is not assignable.
MiLAN Technology makes no express or implied warranties including, but not limited to, any
implied warranty of merchantability or fitness for a particular purpose, except as expressly set
forth in this warranty. In no event shall MiLAN Technology be liable for incidental or
consequential damages, costs, or expenses arising out of or in connection with the performance
of the product delivered hereunder. MiLAN Technology will in no case cover damages arising
out of the product being used in a negligent fashion or manner.

Installation Guide MIL-225C
2 7
Introduction
The MIL-225C is a 100Mbps Fast Ethernet and ATM
(OC-3) device that converts multi-mode fiber optic signals
to single-mode fiber optic signals and vice versa. The
device has two SC connectors:
• SM port (single-mode fiber)
• MM port (multi-mode fiber)
The MIL-225C is capable of supporting both multi-mode
fiber cable with a 2 Km signal driving distance and single-
mode fiber cable with a 15 Km signal driving distance.
The device can also be used in FDDI.
Packaging Contents
The MIL-225C package contains the following:
• MIL-225C multi-mode to single-mode fiber
converter
• Power supply adapter
• Installation guide
Specification for Multi-Mode (MM) Port
• Connector type: SC
• Wavelength: 1261-1360 nm
• Cable specs.: 62.5/125 µ
m
• Min. optical power output: -19.0 dBm
• Max. optical power output: -14.0 dBm
• Receive sensitivity: -30.0 dBm
• Max. optical power input: -14 dBm
• Supports up to 2 km of multi-mode cable
Dimensions:
4.0” x 3.5” x 1”
SC-type Connector
Figure 4. SC-type Connector
SC-Type
TX RX

Installation Guide MIL-225C
6 3
Storage Temperature
• Minimum: -25° C
• Maximum: 75° C
Operating Conditions
Specification for Single-Mode (SM) Port
• Connector type: SC
• Wavelength: 1261-1360 nm
• Cable specs.: 9/125 µ
m
• Min. optical power output: -15.0 dBm
• Max. optical power output: -8.0 dBm
• Receive sensitivity: -31.0 dBm
• Max. optical power input: -8.0 dBm
• Supports up to 15 km of single-mode cable
Features
• Compact, painted metal enclosure
• Power supply adapter
• Diagnostic LEDs
Installation
To install the MIL-225C:
1. Connect an SC-type, single-mode cable to the SM
port on the device.
2. Connect an SC-type, multi-mode cable to the MM
port on the device.
3. Supply power to the MIL-225C using the power
supply adapter included with the unit. Make sure
the PWR LED illuminates.
4. Check the SMSD LED and the MMSD LED for
proper status. This depends on the status of the
devices connected to the unit.
Please contact MiLAN’s technical support if you
experience difficulties installing the MIL-225C.
Table 1: Recommended operation conditions
Parameters Minimum Maximum
Operating Temperature +5° C 40° C
Humidity: non-condensing 10% 95%
Signal Output Load 35 ohm 75 ohm
Supply Voltage 4.75 V 5.25 V

Installation Guide MIL-225C
4 5
Theory of Operation
The MIL-225C is a single-mode to multi-mode fiber
converter for Fast Ethernet, ATM (OC-3), and FDDI
networks. When the device receives an optical input
signal from one port, it will convert it into an electrical
signal. The device will then convert the electrical signal
back to an optical signal suitable for transmission over the
other port.
Figure 3.Theory or Operation
Indicators
There are 3 LED indicators on the MIL-225C:
•
SMSD
:
Single-mode Signal Detection
. This LED
illuminates when MIL-225C receives a valid
link or data traffic signal from the device
connected to the SM port
•
PWR:
Power
. This LED illuminates when the MIL-
225C is powered up (using the power
supply adapter)
•
MMSD
:
Multi-mode Signal Detection
. This LED
illuminates when MIL-225C receives a valid
link or data traffic signal from the device
connected to the MM port
Specifications
Power Supply
External power is required for the MIL-225C. The system
draws 700 mA at normal operation in room temperature
of 25° C.
• A 110 V AC wall mount power supply adapter for
domestic use
• A 220 V AC power supply with IEC receptacle
converting to 5 V DC 1.5 Amp for international use
(according to the country where the unit will
operate in)