MiLAN MIL-S800 User manual

MIL-S800 User’s Guide
8 port 10/100BASE-TX Switch

Regulatory Approval
- FCC ClassA
- UL 1950
- CSA C22.2 No. 950
- EN60950
- CE
- EN55022 Class B
- EN55024
Canadian EMI Notice
This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada.
European Notice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the
Commission of the European Community Compliance with these directives imply conformity to the following European Norms:
- EN55022 (CISPR 22) - Radio Frequency Interference
- EN61000-X - Electromagnetic Immunity
- EN60950 (IEC950) - Product Safety
Five-Year Limited Warranty
MiLAN Technology warrants to the original consumer or purchaser that each of it's products, and
all components thereof, will be free from defects in material and/or workmanship for a
period of five years from the original factory shipment date. Any warranty hereunder is
extended to the original consumer or purchaser and is not assignable.
MiLAN Technology makes no express or implied warranties including, but not limited to, any
implied warranty of merchantability or fitness for a particular purpose, except as expressly set
forth in this warranty. In no event shall MiLAN Technology be liable for incidental or
consequential damages, costs, or expenses arising out of or in connection with the
performance of the product delivered hereunder. MiLAN Technology will in no case cover damages
arising out of the product being used in a negligent fashion or manner.
Trademarks
The MiLAN logo and MiLAN Technology trademarks are registered trademarks ofof MiLAN Technology
in the United States and/or other countries.
To Contact MiLAN Technology
For prompt response when calling for service information, have the following information ready:
- Product serial number and revision
- Date of purchase
- Vendor or place of purchase
You can reach MiLAN Technology technical support at:
E-mail: [email protected]
Telephone: [phone]
Fax: [phone]
MiLAN Technology
1329 Moffett Park Drive
Sunnyvale, CA 94089
United States of America
Telephone: [phone]
Fax: [phone]
http://www.milan.com
info @ milan.com
© Copyright 2003 MiLAN Technology
P/N: 90000377_F

Table of Contents
Chapter1.Introduction Pg 1
1-1 General Description……………………………………. Pg. 1
1-2 Key Features……………………………………………… Pg. 1
1-3 Package Contents……………………………………… Pg. 2
1-4 Hardware Description………………………………….. Pg. 3
Chapter 2. Hardware Installation Pg 4
2-1 Quick Installation………………………………………... Pg. 4
2-2 LED Descriptions…………………………………………. Pg. 5
Chapter 3. Network Application Pg 6
3-1 Stand Alone……………………………………………… Pg. 6
3-2 Uplink Multiple Hubs……………………………………. Pg. 6
Chapter 4. Trouble Shooting Pg 7
Chapter 5. Product Specifications Pg 8
5-1 General Specification………………………………….. Pg. 8
5-2 Performance Specification Pg. 8
5-3 Physical & Environmental Specification……………..…. Pg. 8

1
Chapter 1 Introduction
1-1 General Description
The MIL-S800 switch provides eight auto-sensing 10/100Mbps RJ45 Ethernet ports. This high performance,
low cost, wire speed desktop switch is ideal for any network where 8 ports are needed, for a solution to an
enterprise need or for a home network. The MIL-S800 can be mounted on the wall with keyholes in the
chassis or magnetically attached to any metal surface.
1-2 Key Features
•Compliant with IEEE 802.3, 802.3u & 802.3x standards
•8 Auto-sensing RJ-45 ports for 10BASE-T or 100 BASE-TX connections
•Embedded 2K entry MAC address table
•512KB memory buffer sharing
•Store-and-Forward operation support
•Full duplex and half duplex flow control
•Plug-and-Play configuration auto addresses learning
•LED indicators for power, link speed 100Mbps, link and activity, full duplex and collision
•Space-saving compact size
•Wall or desktop mountable
•Magnets provide installation on any metal surface
•Auto MDI/MDIX

2
1-3 Package Contents
Your package contents should include the following parts:
•One 8-port Auto-sensing switching Hub
•One DC power adapter
•This User’s Guide
•Four rubber feet with adhesive pads
•Two magnets
•Warranty card
Figure 1. Package contents

3
1-4 Hardware Description
The Front Panel
The front panel contains power and LED Indicators.
Figure 2. Front panel view of the MIL-S800
Front panel LED Indicators
Per Device Power
100M (Link on 100Mbps)
LNK/ACT (Link/Activity)
Per Port FDX/COL (Full Duplex/Collision)
For LED details, please refer to Chapter 2, LED Descriptions.
The Rear Panel
The rear panel of the MIL-S800 consists of a DC power connector and 8 auto-sensing ports.
Figure 3. Rear panel view of the MIL-S800
·Eight Auto-sensing RJ-45 ports for 10BASE-T or 100 BASE-TX connections.
·Auto MDI/MDIX: Detects the straight cable connection, NIC or cascade to a hub or switch, without
changing the cable.
·DC Power Connector.

4
Chapter 2 Hardware Installation
2-1 Quick Installation
•The MIL-S800 should be placed in a well-ventilated room with proper temperature and humidity.
•Do not place the unit near water.
•The maximum distance between the port to the standard network interface is 100 meters.
•For desktop installation, ensure the surface is clean, smooth, level and sturdy. Apply self-adhesive rubber
feet to the bottom of the switch near the corners.
•For wall installation, place two screws securely into the wall. Slide the cross recesses on the bottom of the
MIL-S800 onto the screws.
•For mounting the MIL-S800 on a metal surface, install magnets as shown in instructions and apply to
surface.
•Visually check that the power cord is not damaged. Plug the female end of the cord into the rear of the
MIL-S800 and the male end (power converter) into a power outlet.
•Do not plug a phone jack connector into any RJ-45 port. This may cause damage. Use only twisted-pair
cables with RJ-45 connectors that conform to FCC standards.
Figure 4. Installation of switch

5
2-2 LED Descriptions
Figure 5. Front panel view of LED indicators
The following table lists the LEDs and their function.

6
Chapter 3 Network Application
3-1 Stand Alone
The application of a simple standalone switch is illustrated below. The maximum distance between the switch
and the workstation is 100 meters.
Figure 6. The switch as a backbone for a small 10/100BASE-TX network
3-2 Network
You can cascade the MIL-S800 to another hub or a switch without using a crossover cable.
Fi
g
ure 7. Small Network Confi
g
uration

7
Chapter 4 Troubleshooting
•Power
If the power indicator is not on after the power cord is plugged in, check the power outlet or power cord. If
you lose power after the switch has been operating for some time, check for loose power connections,
power losses or surges at the power outlet. Disconnect and reconnect the power. If the problem persists,
contact MiLAN Technical Support.
•Cabling
Verify that the cabling type is correct. Be sure all cable connectors are securely seated in the required
ports. Use standard unshielded twisted-pair (UTP), Category 3, 4, or 5 cables. Use only Category 5
when there is a Fast Ethernet connection. Make sure the distance between the MIL-S800 and the
workstation, is less than 100 meters.

8
Chapter 5 Product Specification
5-1 General Specification
Standard Compliance IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
Number of Ports 8 10/100Mbps Auto-sensing RJ-45 ports
Data Transfer Rate
Ethernet :10Mbps(half duplex)
20Mbps(full duplex)
Fast Ethernet : 100Mbps(half duplex)
200Mbps(full duplex)
Network Cables Unshielded twisted-pair cable
LED Indicators
Per Device Power
Per Port LNK/ACT, 100M, FDX/COL
5-2 Performance Specification
Transmission Method Store and forward
MAC address table 2 K entry MAC address table
Maximum Forwarding
Rate(64byte packets) 14,880 pps /10 BASE-T 148,800 pps /100BASE-TX
Maximum Filtering
Rate(64byte packets) 14,880 pps /10BASE-T 148,800 pps/100BASE-TX
Duplex mode Supports both half and full duplex mode
5-3 Physical & Environmental Specification
Power Supply External power adapter,
DC 9V, 700mA
4.2 Watt power consumption
Dimensions 6.5" (165mm) L x 4.0" (100mm) W x 1.0"
(25mm) H
Temperature
Operating temperature:
0C to 45C (32F to113F)
Storage temperature:
-30C to 60C (-22F to 140F)
Humidity 10% to 90% (non-condensing)
EMI FCC Class B, CE mark

9
90000377_F