Millipore Milli-Q Advantage A10 User manual

MILLI-Q®ADVANTAGE A10®SYSTEM
USER MANUAL

Safety Information
Safety Statement
Your Milli-Q System should be operated according to the instructions in this manual. In particular, the hydraulic and
electrical specifications should be followed and met. It is important to use this equipment as specified in this
manual; using this equipment in a different manner may impair the safety precautions of the Milli-Q System.
Do not remove the covers of the Milli-Q System at any time.
Electrical and mechanical components inside the Milli-Q System
could pose a hazard. A qualified Millipore®Service
Representative should perform any work that needs to be done
while the Milli-Q System is opened.
Safety Symbols
SYMBOL WHAT IT MEANS
This HAZARD symbol is used to refer to instructions in this
manual that need to be done safely and carefully.
This ATTENTION symbol is used to refer to instructions in
this manual that need to be done carefully.
This UV RADIATION sticker is used to refer to a position
on the Milli-Q System Cabinet or inside of it where
exposure to UV light is possible.
This DANGER sticker is used to refer to a position on the
Milli-Q System Cabinet or inside of it that could be
hazardous.
This ELECTRICAL GROUND sticker is used to refer to a
position on the Milli-Q System Cabinet or inside where
an electrical ground connection is made.
This ELECTRICAL DANGER sticker is used to refer to a
position on the Milli-Q System Cabinet or inside where
an electrical danger could exist.
!HAZARD
!

Notice
The information in this document is subject to change without notice and should not be construed as a commitment
by Millipore Corporation. Millipore Corporation assumes no responsibility for any errors that might appear in this
document. This manual is believed to be complete and accurate at the time of publication. In no event shall
Millipore Corporation be liable for incidental or consequential damages in connection with or arising from the use of
this manual.
We manufacture and sell water purification systems designed to produce pure or ultrapure water with specific
characteristics (μS/cm, T, TOC, CFU/ml, Eu/ml) when it leaves the water purification system provided that the
Milli-Q System is fed with water quality within specifications, and properly maintained as required by the supplier.
We do not warrant these systems for any specific applications. It is up to the end user to determine if the quality of
the water produced by our systems matches his expectations, fits with norms/legal requirements and to bear
responsibility resulting from the usage of the water.
Millipore’s Standard Warranty
Millipore Corporation (“Millipore”) warrants its products will meet their applicable published specifications when
used in accordance with their applicable instructions for a period of one year from shipment of the products.
MILLIPORE MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED. THERE IS NO WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The warranty provided herein and the
data, specifications and descriptions of Millipore products appearing in Millipore’s published catalogues and
product Literature may not be altered except by express written agreement signed by an officer of Millipore.
Representations, oral or written, which are inconsistent with this warranty or such publications are not authorised and
if given, should not be relied upon.
In the event of a breach of the foregoing warranty, Millipore’s sole obligation shall be to repair or replace, at its
option, the applicable product or part thereof, provided the customer notifies Millipore promptly of any such breach.
If after exercising reasonable efforts, Millipore is unable to repair or replace the product or part, then Millipore shall
refund to the customer all monies paid for such applicable product or part. MILLIPORE SHALL NOT BE LIABLE
FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR ANY OTHER INDIRECT DAMAGES RESULTING
FROM ECONOMIC LOSS OR PROPERTY DAMAGE SUSTAINED BY ANY CUSTOMER FROM THE USE
OF ITS PRODUCTS.
COPYRIGHT
©2006 MILLIPORE CORPORATION. PRINTED IN FRANCE. ALL RIGHTS RESERVED. THIS BOOK OR PARTS
THEREOF MAY NOT BE REPRODUCED IN ANY FORM WITHOUT THE WRITTEN PERMISSION OF THE
PUBLISHERS.
REV. 0, 11/06
TRADEMARKS
Millipore, A10, Elix, Q-Gard, Milli-Q, Millipak and Milli-RO are registered trademarks of Millipore
Corporation.
BioPak, Quantum, Milli-RX, RiOs and Q-POD are trademarks of Millipore Corporation.
All other trademarks are trademarks of their respective manufacturers.

TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION .............................................................................1
SECTION 1-1 PURPOSE OF THIS USER MANUAL .......................................................................................1
SECTION 1-2 ABOUT MILLIPORE .........................................................................................................1
CHAPTER 2 PRODUCT INFORMATION .................................................................2
SECTION 2-1 OVERVIEW OF THE MILLI-Q WATER SYSTEM ..........................................................................2
SECTION 2-2 MILLI-Q®WATER SPECIFICATIONS .....................................................................................4
SECTION 2-3 FLOW SCHEMATIC........................................................................................................4
SECTION 2-4 TECHNICAL SPECIFICATIONS ............................................................................................7
CHAPTER 3 INSTALLATION ...............................................................................9
SECTION 3-1 INSTALLATION REQUIREMENTS ...........................................................................................9
SECTION 3-2 ASSEMBLING THE Q-POD DISPENSER ...............................................................................11
SECTION 3-3 CONNECTING THE Q-POD DISPENSER TO THE MILLI-Q SYSTEM CABINET ...................................12
SECTION 3-4 FEEDWATER CONNECTION TO THE MILLI-Q SYSTEM CABINET...................................................16
SECTION 3-5 QUICK REFERENCE GUIDE .............................................................................................17
SECTION 3-6 MILLI-Q SYSTEM IS POWERED ON ....................................................................................18
SECTION 3-7 Q-GARD PACK INSTALLATION.........................................................................................20
SECTION 3-8 QUANTUM CARTRIDGE INSTALLATION................................................................................22
SECTION 3-9 RINSING THE MILLI-Q ..................................................................................................24
SECTION 3-10 A10 TOC MONITOR CLEANING ...................................................................................25
SECTION 3-11 INSTALLATION OF THE POD PAK......................................................................................25
SECTION 3-12 HOW TO REGISTER A POD PAK BEING INSTALLED..................................................................27
SECTION 3-13 HOW TO ENTER THE MANAGER MENU .............................................................................28
SECTION 3-14 SELECTING THE LANGUAGE ...........................................................................................29
SECTION 3-15 SETTING THE DATE AND TIME .........................................................................................30
SECTION 3-16 CALIBRATING THE MILLI-Q WATER FLOWRATE ......................................................................31
SECTION 3-17 CHANGING THE SET POINTS .........................................................................................32
SECTION 3-18 OTHER SETTINGS........................................................................................................34
SECTION 3-19 REGISTERING UV AND A10 LAMPS LIFETIME ........................................................................41
CHAPTER 4 USING THE MILLI-Q SYSTEM ..........................................................43
SECTION 4-1 MILLI-Q SYSTEM CABINET KEYPAD AND LCD.......................................................................43
SECTION 4-2 SOFTWARE MAP ........................................................................................................44
SECTION 4-3 STANDBY MODE AND READY MODE ............................................................................45
SECTION 4-4 HOW TO DISPENSE WATER ............................................................................................46
SECTION 4-5 VIEWING AND PRINTING WATER QUALITY ..........................................................................49
SECTION 4-6 UNDERSTANDING THE Q-POD DISPENSER DISPLAY AND KEYPAD ...............................................51
SECTION 4-7 PRINTING THE SYSTEM HISTORY ......................................................................................53

TABLE OF CONTENTS
SECTION 4-8 VIEW OPERATION...................................................................................................... 54
SECTION 4-9 VIEWING CONSUMABLES STATUS................................................................................... 55
SECTION 4-10 CALL MILLIPORE ......................................................................................................... 56
SECTION 4-11 VIEWING SERVICE TRACKING ........................................................................................ 56
SECTION 4-12 VIEWING INFORMATION.............................................................................................. 57
CHAPTER 5 MAINTENANCE............................................................................58
SECTION 5-1 MAINTENANCE SCHEDULE ........................................................................................... 58
SECTION 5-2 HOW TO REPLACE THE Q-GARD PACK ............................................................................. 59
SECTION 5-3 HOW TO REPLACE THE QUANTUM CARTRIDGE .................................................................... 63
SECTION 5-4 HOW TO REPLACE A POD PAK ...................................................................................... 68
SECTION 5-5 HOW TO REPLACE THE UV 185 NM LAMP ........................................................................ 70
SECTION 5-6 HOW TO REPLACE THE A10 LAMP................................................................................... 70
SECTION 5-7 CLEANING THE A10 TOC MONITOR ............................................................................. 71
SECTION 5-8 HOW TO CLEAN THE INLET STRAINER ............................................................................... 72
CHAPTER 6 ALERT AND ALARM MESSAGES.........................................................74
SECTION 6-1 WHAT ARE ALERT AND ALARM MESSAGES? ........................................................................ 74
SECTION 6-2 HOW TO SEE AND CANCEL ALERT MESSAGES ..................................................................... 75
SECTION 6-3 HOW TO SEE AND CANCEL ALARM MESSAGES.................................................................... 79
SECTION 6-4 SUMMARY OF ALERT MESSAGES AND WHAT TO DO .............................................................. 82
SECTION 6-5 SUMMARY OF ALARM MESSAGES AND WHAT TO DO ............................................................. 84
CHAPTER 7 ORDERING INFORMATION .............................................................89
SECTION 7-1 CATALOGUE NUMBERS FOR CONSUMABLES....................................................................... 89
SECTION 7-2 CATALOGUE NUMBERS FOR ACCESSORIES......................................................................... 90
SECTION 7-3 CATALOGUE NUMBERS FOR MILLI-Q ADVANTAGE A10 SYSTEM............................................... 90

INTRODUCTION
1
CHAPTER 1 INTRODUCTION
Section 1-1 PURPOSE OF THIS USER MANUAL
This User Manual is intended for use with a Milli-Q® Advantage A10 Water Purification System.
This User Manual is a guide for use during the installation, normal operation and maintenance of a
Milli-Q Advantage A10 Water Purification System. It is highly recommended to completely read this manual and to
fully comprehend its contents before attempting installation, normal operation or maintenance of the Water
Purification System.
If this User Manual is not the correct one for your Water Purification System, then please contact Millipore.
The term “Milli-Q Advantage A10 Water Purification System” is replaced by the term “Milli-Q System” for the
remainder of this User Manual unless otherwise noted.
Section 1-2 ABOUT MILLIPORE
1-2.1 TELEPHONE
See the Business Card(s) on the inside cover of the User Manual binder.
1-2.2 INTERNET
The Millipore Internet site address can be used to submit a question to Millipore via electronic mail. The Millipore
Internet site can be used to find addresses, telephone/fax numbers and other information.
Internet site address: www.millipore.com/bioscience
1-2.3 CONTACT INFORMATION FOUND ON THE MAIN DISPLAY
Contact information about Millipore can be found on the Main Display. See Section 4-10 (CALL MILLIPORE) for
more information.
1-2.4 MANUFACTURING SITE
Millipore SAS
67120 Molsheim
FRANCE

PRODUCT INFORMATION
2
CHAPTER 2 PRODUCT INFORMATION
Section 2-1 OVERVIEW OF THE MILLI-Q WATER SYSTEM
2-1.1 MILLI-Q SYSTEM CABINET
Milli-Q System Cabinet Input or output connections
1 Not Used A Power Entry (100 – 240 VAC)
2 Feedwater Port B Accessories Power (maximum 24
VDC)
3 Water to Q-POD Dispenser C PS/2 Connection (maximum 5 VDC)
4 Water from Q-POD
Dispenser
D Level Sensor Input (maximum 5
VDC)
5, 6, 7, 8, 9 Not Used E Ethernet Connection (maximum 5
VDC)
A
C
D
B
E

PRODUCT INFORMATION
3
2-1.2 Q-POD DISPENSER
Printer
Port PS/2 Connections Footswitch Tubings
2-1.3 RC-LINK
PS/2 Cable Termination Plug Tubings

PRODUCT INFORMATION
4
Section 2-2 MILLI-Q®WATER SPECIFICATIONS
FLOWRATES (FROM Q-POD DISPENSER 1)
 0.05 Lpm – 2.0 Lpm
RESISTIVITY
 18.2 MΩ.cm @25°C
CONDUCTIVITY
 0.055 μS/cm @25°C
PYROGENS
 < 0.001 Eu/ml with BioPak™ Ultrafilter
PARTICLES
 ≤1/ml (particle size > 0.22 μm) with Millipak®
Express 40 Filter or BioPak Ultrafilter
TOC
 < 5 ppb
This specification came from test conditions where a
Milli-Q System was fitted with a Q-Gard®T1 Pack
and a Quantum™ TEX Cartridge and the feedwater
came from a Millipore RiOs™ Water System. The
feedwater TOC value was < 50 ppb. The TOC of
the Milli-Q Water can vary as a function of the
feedwater TOC.
MICRO-ORGANISMS
 ≤1 CFU/ml with Millipak Express 40 Filter or
BioPak Ultrafilter
RNASE AND DNASE
 RNase < 0.01 ng/mL with BioPak Ultrafilter
 DNase < 4 pg/μL with BioPak Ultrafilter
Section 2-3 FLOW SCHEMATIC
2-3.1 DIAGRAM
The water flow through a Milli-Q System is shown here in a flow diagram. A description of each item is in Section
2-3.2.
ITEM DESCRIPTION ITEM DESCRIPTION
A Pump D Quantum Cartridge
B Q-Gard Purification Pack E POD Pak
C UV 185 nm Lamp F A10 TOC Monitor
A
BCD
E
F

PRODUCT INFORMATION
5
2-3.2 DESCRIPTION OF FLOW SCHEMATIC
The flow schematic is a simplified drawing of all the major components in a Milli-Q System.
Q-GARD PURIFICATION PACK
The Q-Gard Purification Pack is used to remove ions and organic molecules from the feedwater. The term “Q-Gard
Pack” replaces “Q-Gard Purification Pack” for the remainder of this User Manual unless otherwise noted.
The Q-Gard Pack is a consumable. A consumable is something that is periodically changed out for a new one
during the maintenance of the Milli-Q System.
There are different types of Q-Gard Packs. The use of each Q-Gard Pack is dependent upon the type of feedwater.
 Q-GARD T1 PACK
The Q-Gard T1 Pack is used when the feedwater comes from RO, distillation or Electrodeionisation (EDI). An
example of RO or EDI feedwater is the water coming from either a Millipore RiOs System or Elix®Water Purification
System. This type of feedwater typically has some ions but contains little organic, particulate and colloidal
contamination.
 Q-GARD T2 PACK
The Q-Gard T2 Pack is used whenever the feedwater comes from a source other than mentioned above. The same
feedwater would have a Fouling Index ≤5.
 Q-GARD T3 PACK
The Q-Gard T3 Pack is used instead of a Q-Gard T2 Pack whenever the feedwater has a Fouling Index > 5.
UV 185 NM LAMP
The dual wavelength UV 185 nm Lamp emits light at 185 nm (for TOC reduction) and at 254 nm (Germicidal
action). The UV 185 nm Lamp is used to kill bacteria and to reduce the levels of organic molecules in the water.
The UV 185 nm Lamp is a consumable.
QUANTUM CARTRIDGE
The Quantum Cartridge is used to remove trace levels of ions and organic molecules.
The Quantum Cartridge is a consumable.
 QUANTUM TIX CARTRIDGE
The Quantum TIX Cartridge contains only ion exchange resin. This type of Quantum Cartridge is used when
maintaining absolutely trace levels of ions is critical.
 QUANTUM TEX CARTRIDGE
The Quantum TEX Cartridge contains ion exchange resin and synthetic carbon. These purification media are used
when the Milli-Q Water needs to have both trace levels of ions and trace levels of organic molecules.
A10 TOC MONITOR
The A10 TOC Monitor measures the Total Oxidizable Carbon (TOC) of the Milli-Q Water.
The A10 TOC Monitor uses a small lamp during its TOC Analysis Mode. This is called the A10 Lamp.
The A10 Lamp is a consumable.

PRODUCT INFORMATION
6
POD PAK
The POD Pak is a water purification device that is attached to the Q-POD Dispenser outlet. It is the final purification
device used before Milli-Q Water is dispensed. The POD Pak provides additional quality and insurance that trace
contaminants related to specific applications are removed just before ultrapure water is delivered.
The POD Pak is a consumable.
The LCD messages sometimes refer to POD Pak 1 or POD Pak 2 (or 3). POD Pak 1 means the POD Pak on the 1st
Q-POD Dispenser. POD Pak 2 refers to the POD Pak installed on a second Q-POD Dispenser.
 MILLIPAK EXPRESS 40 FILTER
The Millipak Express 40 Filter is a type of POD Pak. The Millipak Express 40 Filter is a membrane-based filter that
removes all particles and bacteria with a size greater than 0.22 μm by a sieving mechanism. All contaminants
larger than the filter pore size are retained on its surface. This blocks and retains any bacteria in the water passing
through it.
 BIOPAK ULTRAFILTER
The BioPak Ultrafilter is a type of POD Pak. The BioPak Ultrafilter removes bacteria, nucleases (RNases, DNases)
and Endotoxins (Pyrogens) from the Milli-Q Water.

PRODUCT INFORMATION
7
Section 2-4 TECHNICAL SPECIFICATIONS
2-4.1 DIMENSIONS
MILLI-Q CABINET
Q-POD DISPENSER

PRODUCT INFORMATION
8
2-4.2 WEIGHT
ITEM SHIPPING WEIGHT DRY WEIGHT WET WEIGHT
Milli-Q System Cabinet (no
Q-POD Dispenser) 17.0 kg 13.0 kg 19.0 kg
Q-POD Dispenser 7.2 kg 4.7 kg 4.7 kg
2-4.3 ELECTRICAL
 Power source voltage 100-230 V ±10%
 Power used 160 VA
 Power source frequency range 50-60 Hz ±10%
 Power Entry Module Fuse 2.5 Amp Fast Acting; 5 mm x 20 mm; 250 V Safety
Voltage; Millipore Spare Part Number FTPF07054. The
fuse should be serviced by a qualified Millipore Service
Representative.
 Earth Ground The power source must be earth grounded.
 Power Cord The Power Cord should be plugged into a wall outlet that is
accessible. The Milli-Q System is powered on and off by
removing the power cord from the wall outlet.
 Maximum distance from power source to
Milli-Q System 2.5 meters
2-4.4 DISPLAYED VALUE RANGES
 Resistivity displayed value range 2 MΩ.cm – 18.2 MΩ.cm @25°C
 Conductivity displayed value range 1 μS/cm – 0.055 μS/cm @25°C
 Temperature displayed value range 0°C – 50°C
 TOC displayed value range 1 ppb – 999 ppb
 Flowmeter displayed value range 0.5 Lpm – 3 Lpm
2-4.5 MATERIALS OF CONSTRUCTION
Please contact Millipore for a list of the Materials of Construction.
2-4.6 NOISE LEVEL
Noise level = 47 dB at a distance of 1 meter.

INSTALLATION
9
CHAPTER 3 INSTALLATION
Section 3-1 INSTALLATION REQUIREMENTS
3-1.1 CONSUMABLES
The consumables needed for installation are listed below. Please note that these items are not included with the
Milli-Q System. A Milli-Q System is comprised of a Milli-Q System Cabinet, a Q-POD Dispenser with RC-Link.
In addition to the Milli-Q System, you need:
 1 Q-Gard Pack
 1 Quantum Cartridge
 1 POD Pak (Millipak Express 40 Filter or BioPak Ultrafilter)
3-1.2 SPACE
See Section 2-4.1 for dimensional information. The installation area needs to accommodate the total operating
space of the Milli-Q System.
3-1.3 WEIGHT
See Section 2-4.2 for weight information. The installation area needs to accommodate the total operating weight
of the Milli-Q System.
3-1.4 ELECTRICAL
See Section 2-4.3 for electrical information. The electrical supply needs to meet the stated electrical specifications.
3-1.5 FEEDWATER
TYPE OF FEEDWATER REQUIRED
 Pre-treated water including one or several of the following technologies: RO; RO + EDI; RO
+ DI; Distillation; DI.
FEEDWATER PHYSICAL REQUIREMENTS
 Flowrate > 2 Lpm
 Pressure range 0.0 – 0.3 bar
 Connection thread size and connection type 1/2 inch male GAZ (BSP, NPT)
 Feedwater tubing OD 8 mm OD
 Feedwater tubing maximum length 2 meters
FEEDWATER CHEMISTRY REQUIREMENTS
 Temperature range 5°C – 35°C
 pH range 4 - 10
 Conductivity range < 100 μS/cm @25°C
 Fouling Index < 5
 TOC (maximum value) < 50 ppb

INSTALLATION
10
3-1.6 ENVIRONMENTAL
AMBIENT TEMPERATURES
 Ambient storage temperature range 4°C – 40°C
 Ambient operation temperature range 4°C – 40°C
OTHER ENVIRONMENTAL REQUIREMENTS
 Location The Milli-Q System is intended for indoor use only.
 Relative Humidity during storage
and operation Maximum relative humidity 80% for temperatures up to 31°C decreasing linearly to 50% relative humidity at 40°C.
 Altitude < 3000 meters
 Pollution Degree 2
 Installation Category II

INSTALLATION
11
Section 3-2 ASSEMBLING THE Q-POD DISPENSER
1. Open the Q-POD Dispenser box.
2. Locate the Q-POD Base and the Q-POD Mast. Screw them together. See the photograph below.
3. Locate the Q-POD Arm. Press on the locking handle and slide the Q-POD Arm onto the Q-POD Mast. Note
that the height can be adjusted up or down.
Q-POD Mast to Q-POD Base with bolt. Q-POD Arm being put on Q-POD
Mast.
Q-POD Dispenser on Q-POD Arm.

INSTALLATION
12
Section 3-3 CONNECTING THE Q-POD DISPENSER TO THE MILLI-Q SYSTEM CABINET
3-3.1 CONNECTING THE RC-LINK TO THE Q-POD DISPENSER
The Q-POD Dispenser installation instructions in this User Manual
are written for the case of one Q-POD Dispenser being connected to
the Milli-Q System Cabinet. If the Milli-Q System Cabinet is going
to have two or three Q-POD Dispensers, then refer to the Insert
document supplied with the Q-POD Dispenser.
Locate the RC-Link in the Q-POD Dispenser Accessories Bag. The RC-Link consists of a PS/2 cable with two lengths
of tubing. The cable and the tubing lengths are enclosed in a sheath. The RC-Link is 2.5 metres in length. The
cable terminates on each end with a PS/2 connection.
RC-LINK TUBING CONNECTIONS TO THE Q-POD BASE
1. Locate the two tubing ports on the back of the Q-POD Dispenser Base. See the illustrations below.
2. Unscrew the 2 nuts from the Q-POD Dispenser ports.
Either end of the RC-Link can be attached to the Q-POD Dispenser.
3. Connect the RC-Link tubing to the Q-POD Dispenser Ports.
RC-LINK CABLE CONNECTION TO THE Q-POD BASE
1. Locate the Termination Plug (small electronic device) that came in the Q-POD Dispenser Accessories Bag. Plug
this into one PS/2 connection on the Q-POD Base.
When the Milli-Q System Cabinet is connected to one Q-POD
Dispenser, both PS/2 connections are used on the Q-POD Base.
One connection is used with the RC-Link cable. The other
connection is used for the Termination Plug.
2. Plug the RC-Link cable in the other PS/2 connection on the Q-POD Base.
The RC-Link cable can be plugged into either PS/2 connection on
the Q-POD Dispenser Base.
ATTENTION
ATTENTION
ATTENTION
ATTENTION

INSTALLATION
13
Q-POD Base without RC-Link attached. RC-Link tubing being attached to one port
on Q-POD Base.
RC-Link tubing attached to 2nd port on Q-POD Base.
PS/2 Cable from RC-Link attached to
Q-POD Base.
Termination Plug attached to
Q-POD Base.

INSTALLATION
14
3-3.2 CONNECTING THE RC-LINK TO THE MILLI-Q SYSTEM CABINET
RC-LINK TUBING CONNECTIONS TO THE MILLI-Q SYSTEM CABINET
1. Locate Port 3 and Port 4 on the Milli-Q System Cabinet.
2. Plug one length of tubing from the RC-Link into Port 4. When the tubing is pushed in, pull on it to make sure it is
securely fastened.
The Q-POD Dispenser design allows for either length of RC-Link
tubing to be connected to Port 4 on the Milli-Q System Cabinet.
3. Plug the other length of tubing into Port 3. This Port uses a nut to secure the tubing to a plastic stem. Unscrew
the nut from Port 3. Push the end of the tubing through the nut. Push this end of the tubing onto the plastic stem.
Screw the nut.
Make sure the RC-Link tubing lengths are connected to Port 3 and to
Port 4. Do not connect the RC-Link tubing to any other ports on the
Milli-Q System Cabinet.
RC-LINK CABLE CONNECTION TO THE MILLI-Q SYSTEM CABINET
1. Locate the PS/2 connection on the Milli-Q System Cabinet. It is located below where the Power Cord plugs
in.
2. Plug the RC-Link PS/2 cable into the Milli-Q System Cabinet.
Make sure all PS/2 connections (cable and termination plug) are
pushed in completely.
A
TTENTION
A
TTENTION
A
TTENTION

INSTALLATION
15
Milli-Q System Cabinet without RC-
Link connected.
PS/2 Cable connected to Milli-Q
System Cabinet.
RC-Link tubing to Port 4. RC-Link tubing to Port 3.