Milwaukee MW500 User manual

USER MANUAL
MW500
PRO ORP Meter
milwaukeeinstruments.com (USA & CAN)
milwaukeeinst.com
CERTIFICATION
Milwaukee Instruments conform to the
CEEuropean Directives.
Disposal of Electrical & Electronic
Equipment. Do not treat this product as
household waste. Hand it over to the
appropriate collection point for the recycling of
electrical and electronic equipment.
Disposal of waste batteries. This product
contains batteries. Do not dispose of them
with other household waste. Hand them
over to the appropriate collection point for recycling.
Please note: proper product and battery disposal
prevents potential negative consequences for human
health and the environment. For detailed information,
contact your local household waste disposal service
or go to www.milwaukeeinstruments.com (USA &
CAN) or www.milwaukeeinst.com.
RECOMMENDATION
Before using this product, make sure it is entirely
suitable for your specific application and for the
environment in which it is used. Any modification
introduced by the user to the supplied equipment
may compromise the meter’s performance. For your
and the meter’s safety do not use or store the meter in
hazardous environment. To avoid damage or burn, do
not perform any measurement in microwave ovens.
WARRANTY
This instrument is warranted against defects in
materials and manufacturing for a period of 2 years
from the date of purchase. Probe is warranted for
6 months. This warranty is limited to repair or free
of charge replacement if the instrument cannot be
repaired. Damage due to accidents, misuse, tampering
or lack of prescribed maintenance is not covered by
warranty. If service is required, contact your local
Milwaukee Instruments Technical Service. If the repair
is not covered by the warranty, you will be notified of the
charges incurred. When shipping any meter, make sure
it is properly packaged for complete protection.
Milwaukee Instruments reserves the right to make
improvements in design, construction and appearance
of its products without advance notice.
SATISFACTION
GUARANTEED
ISTMW500 07/20

OPERATION
yThe meter is supplied complete with a 9V battery.
Slide o the battery compartment cover located
on the back of the meter. Install the battery into the
battery clip connector while observing polarity.
yAlways remove the electrode protective cap before
taking any measurement. If the electrode has been
left dry, soak the tip in storage solution for a few
minutes to reactivate it.
yConnect the ORP electrode to the BNC socket on the
top of the meter.
yImmerse the tip (2.5 cm) of the ORP electrode into the
sample.
yTurn the instrument on by pressing the ON/OFF key.
yAllow the reading to stabilize before taking
measurements.
yAfter use, switch the meter o and store the
electrode with a few drops of storage solution in the
protective cap.
yThe meter is factory calibrated. ORP electrodes are
interchangeable and no mV calibration is needed
when they are replaced.
MAINTENANCE:
yThe surface of the ORP electrode must always be
clean. Use M10000B rinse solution for this purpose.
If needed, clean the Platinum tip with very fine
abrasive paper.
yWhen not in use, the tip (reference junction) of the
electrode should always be kept moist and safe
from any mechanical stress.
BATTERY REPLACEMENT
When the battery becomes weak the meter will
display “ “, the low battery indicator. The battery
has about 50 hours of working time left. A low battery
will result in unreliable measurements. Prompt battery
replacement is required.
Battery replacement must only take place in a non
hazardous area using an alkaline 9V battery.
Turn the meter o, slide the battery compartment
cover located at the rear of the meter o and replace
the 9V battery with a new one. Make sure the battery
contacts are fully engaged in the connector, seat the
battery in its compartment and replace the cover.
SPECIFICATIONS
RANGE ±1000 mV
RESOLUTION 1 mV
ACCURACY (@25 °C) ±5 mV
TYPICAL EMC
DEVIATION ±5 mV
ORP ELECTRODE SE-300 (included)
ENVIRONMENT 0 to 50 °C; 95% RH max.
BATTERY TYPE 9V alkaline (included)
BATTERY LIFE approx. 300 hours of use
DIMENSIONS 143 x 80 x 32 mm
WEIGHT 220 g (with battery)
meter only
OPTIONAL ACCESSORIES
M10000B Electrode rinse solution, 20 ml sachet,
25 pcs.
MA9015 Electrode storage solution, 220 mL
bottle
SE-300 Platinum ORP electrode with 1 m cable