Milwaukee M12 T LED User manual

Cat. No.
M12 T LED, M18 T LED
M12 / M18 LEDWork Light
WARNING
To reduce the risk of injury, user must read and understand operator's manual.
OPERATOR'S MANUAL

• To reduce the risk of injury, close supervision
is necessary when an appliance is used near
children.
• Store idle work light out of reach of children.
Warm work lights can become hazardous in the
hands of children.
• Do not use outdoors.
SAVE THESE
INSTRUCTIONS
1
FUNCTIONAL DESCRIPTION
2
4
3
5
5
1. Bezel
assembly
2. On/Off
button
3. Magnet
4. Hook
5. Pivot head
2
•
•Use work light only with specifically desig-
nated battery pack. Use of any other batteries
may create a risk of fire.
•When battery pack is not in use, keep it away
from metal objects like: paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause sparks, burns, or a fire.
Inserting/Removing Battery Pack
Insert the battery pack by sliding battery pack into
the body of the tool. Insert the battery pack until
the battery latches lock.
To remove the battery pack, press in both battery
latches and slide the battery pack off of the tool.
Before using the work light, read this operator's
manual, your battery pack and charger operator's
manual, and all labels on the battery pack, charger
and work light.
Batteries must be recharged only with the
charger specified by MILWAUKEE®.A charger
that may be suitable for one type of battery may
create a risk of fire when used with another
battery.
• Maintain labels and nameplates. These carry
important information.
The light source contained in this luminaire shall
only be replaced by the manufacturer or his
service agent or a similar qualified person.
•
READ AND UNDERSTAND ALL
INSTRUCTIONS. When using
IMPORTANT SAFETY INSTRUCTIONS
WARNING
WARNING
Do not charge non-rechargeable
batteries.
electric appliances, basic precautions should
always be followed, including the following:
WARNING
The lens gets very hot
during use. To reduce the risk
of burns, do not touch hot lens.
SPECIFICATIONS
Cat. No......................... M12 T LED / M18 T LED
Volts............................................... 12V / 18 V DC
Watts ................................................. 4 W / 3.7 W
Charger Type............................................. M18™
Use only MILWAUKEE®M12 or M18 Li-Ion
battery packs.
SYMBOLOGY
Read Operator's Manual
Regulatory Compliance Mark (RCM).
This product meets applicable
regulatory requirements.
Do not dispose of electric tools
together with household waste
material. Electric tools and electronic
equipment that have reached the end
of their life must be collected
separately and returned to an
environmentally compatible recycling
facility.
Volts
Direct Current
Do not stare into light.
Class III protection
Warning
Indoor use
ADDITIONAL BATTERY SAFETY RULES
WARNING
WARNING
Do not charge non-rechargeable
batteries.
2
ASSEMBLY
To reduce the risk of fire, personal
injury, and product damage due to
a short circuit, never immerse your tool, battery
pack or charger in fluid or allow a fluid to flow
inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and
bleach or bleach-containing products, etc., can
cause a short circuit.
WARNING
Recharge only with the charger
specified for the battery. For
specific charging instructions, read the
operator’s manual supplied with your charger
and battery.
WARNING
To reduce the risk of injury, do
not look directly into the light
when the work light is on.

3
Cleaning
Pull
out
Press
To turn on the work light, press the ON/OFF but-
ton. To turn off the work light, press the ON/OFF
button again.
Hook
M18 T LED
Adjusting the Pivot Head
M 2 - The pivot head can pivot to a
range of 90°; with detents every 15°. Pivot head to
desired position. Allow the detent to snap into
place. Do not forcibly pivot the head.
Maintain Work Light
M18 T LED - The pivot
head can pivot to a
range of 135°; with
detents every 10°. Pivot
head to desired
position. Allow the
detent to snap into
place. Do not forcibly
pivot the head.
To use the
hanging hook,
press in the
hook joint. Pull
the hook out.
WARNING
OPERATION
MAINTENANCE
To reduce the risk of injury,
always unplug the charger and
remove the battery pack from the charger or
tool before performing any maintenance.
Never disassemble the tool, battery pack or
charger. Contact a MILWAUKEE®service
facility for ALL repairs.
Keep your work light, battery pack and charger in
good repair by adopting a regular maintenance
program. If the work light does not work properly,
return the work light to a MILWAUKEE®service
facility for evaluation and repair.
Keep tool handles clean, dry and free of oil or
grease. Use only mild soap and a damp cloth to
clean the tool, battery pack and charger since
certain cleaning agents and solvents are harmful
to plastics and other insulated parts. Some of
these include petrol, turpentine, lacquer thinner,
paint thinner, chlorinated cleaning solvents,
ammonia and household detergents containing
ammonia. Never use flammable or combustible
solvents around tools.
ACCESSORIES
WARNING
Always remove battery pack
before changing or removing
accessories. Only use accessories
specifically recommended for this tool.
Others may be hazardous.
For a complete listing of accessories, refer to your
MILWAUKEE®Electric Tool catalogue or go online
to milwaukeetool.com.au / milwaukeetool.co.nz or
contact a distributor. To obtain a catalogue,
contact your local distributor or a service centre.

WARRANTY - AUSTRALIA and NEW ZEALAND
SERVICE - AUSTRALIA and NEW ZEALAND
MILWAUKEE®prides itself in producing a premium quality product that is Nothing But Heavy DutyTM.
Your satisfaction with our products is very important to us! If you encounter any problems with the
operation of this tool, please contact your authorised MILWAUKEE®dealer.
For a list of MILWAUKEE®dealers, guarantee or service agents please contact MILWAUKEE®
Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 645 928)
(New Zealand Toll Free Telephone Number 0800 645 928)
or visit milwaukeetool.com.au/milwaukeetool.co.nz.
Please refer to Australian and New Zealand warranty supplied with tool. This warranty applies only to
product sold by authorised dealers in Australia and New Zealand.
961011193-03(A)
DESIGNED BY MILWAUKEE ELECTRIC TOOL CORP.
PROFESSIONALLY MADE IN CHINA
PRINTED IN CHINA
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Tool (Australia)
26 - 40 Nina Link, Dandenong South,
Victoria, 3175, Australia
Milwaukee Tool (New Zealand)
274 Church Street, Penrose,
Auckland, 1061, New Zealand