Mini Gadgets 8802aj User manual

User Manual
Wireless InsPection Camera
with Color LCD Monitor
w
Version No.: 1.0
Please read this user Manual carefully before using this product!

* 8802AJ means G88802(camera) + GB78o2(monitor)

WELCOME
Thanks you for choosing our inspection video camera and color LCD
monitor. Please read the operation guide carefully before using this
Droo ucr.
The product is designed as a remote inspection device. It can be
used to look into tight spots and beam back real-time video to monitor.
Typical applications might include HVAC inspection, automotive
inspection, cable routing, automotive/boat/aircraft inspection, etc.
PACKING LIST
r \*/
| | Mini camera wiih I
IHandholdcripxl J I rmtuOext Iw
l-.--_]
l"l
I Accessory I
I Mirrorxl I
_r-

STRUCTURE
Power Indicator
.Signal
Flexible
Tube
Camera.
ANd LEDS
,Power Indicator
"LCD ON/OFF
.Power ON/OFF
.Image Orientation
- Brig htness
"Contrast
Power SuoDlv
Socket Signal InPUt
''. Video Output
-2-

INSTALLATION
Please install the batteries. tube first before using the product, and
choose the accessory according to actual situation.
Steps of installation as following'
1. To Install Batteries
1-1. Using a screwdriver, remove screw and cover.
1-2. Remove battery compartment and insert four new AA batteries into
the proper slots in the battery compartment. Proper battery
orientation is indicated on the batterv compartment.
!!"ru-!!
1-3. Reinstall battery compartment and battery cover and screw as
before.
IIEEI O.V your hands before installation or replacing batteries.
-3-

2. To Install The Camera With Flexible Tube
Connect the camera with tube to the body, make sure the keyed ends
are properly aligned. Once they are aligned, finger tighten the knurled
knob to hold the connection in Dlace.
3. To Install Accessory
The three included accessories, {mirror, hook and magnet) all attached
to the imager head the same way.
To connect, hold the imager head, Slip the end of the accessory over
the flats of the imager head.
finqer tiqhten
the linurle? knob

MONITOR POWER SUPPLY
Plug the connect cable into power socket of monitor, and plug the end
of connect cable into adapter, then connect the adapter to 8V-36V
power, the power indicator will lights on red, which indicates being
charging.
6qn ffid
1.2'V o-Nlll)rcJ
\<=J W=4-
The built-in Li-battery will be charged after the adapter is plugged
in, and the Red indicator lights up during charging and will turn off after
a full charge.
A full charge can power the monitor for about 5 hours continuously'
lf, Wnen charging, the monitor will be available,
-5-

GENERAL SAFETY INFORMATION
WARNING! Read and understand all instructions.Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious Personal injurY.
SAVE THESE INSTRUCTIONS!
Prevent object and liquid entry. Never spill liquid of any kind on
the video display unit. Liquid increases the risk of electrical shock
and damage to the product
The unit is not shock-resistant. Do not use it as a hammer or
droD it.
Do not immerse the camera and monitor in water' Store in a
dry place. Such measures reduce the risk of electric shock and da-
mage. The imager head and the cable are water resistant when the
unit is fully assembled, but the monitor and camera is not.
Do not use the camera if condensation forms inside the lens'
Let the water evaporate before using again.
Operation
1. Roll the ON/OFF switch to turn on the camera, and the power indicator
will lights,The switch then acts as a dimmer for the twin LEDs that sur-
round the camera on the imager head and provide lighting.
provide lighting
-6-

)Slide the ON/OFF switch to ON position, and power indicator will lights
on green, the picture display on LCD. Adjust brightness. contrat.
orientation, and rollthe ON/OFF switch of the camera for better image
effect.
3. When in use, the tube should easily maneuver itself into position
going forward.
lllfl The flexible tube can be
bent into a certain shaDe.
This may help you explore
the tube into narrow areas,
* The camera/monitor are
comDatible with both wired
and wireless.
4. The accessories of Handhold
Inspection Camera can be used
to retrieve small items like
dropped rings or screws.
he switch act
as a dimmer
discretely i nteg rative
-7-