MINOURA GravityStand-2 User manual

GravityStand-2 instructions manual
1Insert Plastic Bracket into
each Leg.
Plastic
Bracket
Leg
2Insert Metal Plate Nut
into Lower Pillar from the
bottom.
Put Plastic Cover onto each
Leg, then put through Guide
Pin into either hole for
temporally assembling.
Make sure the square holes
on the Lower Pillar face to
the front side.
Lower Pillar
Guide Pin
Plastic Cover
Metal Plate Nut
Leg
3Screw M6x40 Bolt into the
hole without Guide Pin.
(You don't need to tighten
the bolts so much now.)
M6x40 Bolt
M6x40 Bolt
4
!
GravityStand is designed to keep
enough stability. But we highly
recommend you to x the stand
to the wall with the supplied strap
M3.5x15 or 25
Screw
to prevent any
accident.
Cradle Hook is
padded with soft
urethane to protect
your bikes finish.
Angle & position are
adjustable.
Cradle height is
adjustable in 3
positions without
requiring any tools.
Set up is very easy.
Just lean to the wall.
(Pillar should be set
parallel to the wall)
Remove Guide Pin.
Remove
5Screw M6x40 Bolt to
another hole.
M6x40 Bolt M6x40 Bolt
6Tighten all M6x40 Bolts
firmly.
7Install Metal Plate Nut to
the top holes on Lower Pillar
with M6x12 Bolt.
Metal
Plate
Nut
M6x12 Bolt
- 1 -
(ver.1.3 2014/8)
Required Tool: 1 x M5 Hex Wrench (included)
<Assembled Image>
Guide Pin
!
Hook pad may leave
a mark on the frame.
Consider wrapping
the hook with bar
tape to avoid any
staining.

- 2 -
8Join Upper Pillar with
the installed metal plate
nuts. Make sure the square
holes on Upper Pillar align
correctly.
Tighten the M6x12 bolts
firmly.
Lower Pillar
Upper
Pillar
M6x12 Bolt
9Install Cradle Base in the
preferred spot.
Hook both ends into the
square holes then slide down
to lock into place.
The lower hook is intentio-
nally wider than the hole
width and acts as a spring to
hold the cradle stably.
Cradle Base
10
Push the plastic Lock Lever
toward the pillar to lock
Cradle Base position.
To change Cradle Base
position, pull back Lock
Lever then pull out the
cradle.
11
Lock Lever
Use a at screw-driver
to release Lock Lever.
Do NOT do with your
nger, otherwise your
nail may be damaged.
!
Assemble Bike Cradle.
Angle Adjust Plate
Cradle Bar
Cradle Hook
M6x14 Bolt
M6x20 Bolt
Flat & Spring
Washers
Set Angle Adjust Plate with the
long hole facing down. Cradle
Hook must be installed from the
back of Cradle Bar to prevent
possible scratching or marring of
your frame.
12
Bike cradle is angle adjustable to fit
to your bike's top-tube angle.
Loosen the lower bolt (long hole
side) to adjust. After that tighten
the bolt firmly.
The bike should be set as hori-
zontal as possible.
Set and lean GravityStand to the
wall.
The pillar must be set parallel to
the wall so the bottom side will be
wider for increased stability.
Put the top-tube of your bike on
Cradle Hooks gently.
The stand should be in
contact directly with the
oor or carpet. Do not put
anything between the stand
and oor that might cause
the stand to slip.
!
13
Each position and angle of Cradle
Hook is also adjustable.
IMPORTANT NOTES
• GravityStand is only for holding
normal 2-wheel bikes. Do not use for
any other purposes than instructed.
• GravityStand is free standing. It is not
xed or supported. Be careful not to
hit or bump the stand when passing.
• GravityStand is designed to
absorb normal contact. But we do
recommend using the supplied strap
to provide greater stability.
• Remove any sand and dust from the
area Leg touches to prevent slippage
problem. Do not place paper or
sheet under the leg.
• The hook may stain lighter colored
frames. We suggest wrapping the
hook in bar tape to prevent any
cosmetic damage from happening.
• Check to make sure the bolts on the
stand are tight. Tighten rmly with
the proper tools when needed.
• Minoura offers 1-year limited
warranty from the date of your
purchase. Any problem caused by
manufacturer's defect and wrong
workmanship will be covered by this
program. But any trouble caused
by user's misuse, unapproved
modication, natural calamity and
every problem happened during
shipment will NOT be covered by
Minoura.
For more detail, please refer the
attached "Warranty Program
Instruction" card and Minoura's web
site.
FOR MORE INFORMATION
If you have any quetion, contact
the shop where you purchased or the
distributor in your country first.
The distributor information can be
found on Minoura's web site.
MINOURA JAPAN
1197-1 Godo, Anpachi, Gifu 503-2305
Phone [phone]
Fax [phone]
Mail [email protected]
Web www.minoura.jp
Made in Japan
Push